Supermicro X12SPA-TF User manual

X12SPA-TF
ENGLISH
繁體中文
简体中文
日本語
( 한국어
QUICK REFERENCE GUIDE
Revision 1.0b

X12SPA-TF QUICK REFERENCE GUIDE
Standardized Warning Statements
Motherboards
About Standardized Warning Statements
The following statements are industry standard warnings, provided to warn the user of situations where bodily injury
might occur. Should you have questions or experience di󰀩culty, contact Supermicro's Technical Support Department
for assistance. Only certied technicians should attempt to install or congure components.
Read this section in its entirety before installing or conguring components in the Supermicro chassis.
WARNING: This product can expose you to chemicals including
lead, known to the State of California to cause cancer and birth
defects or other reproductive harm. For more information, go
to www.P65Warnings.ca.gov.
!
Battery Handling
Warning!
There is a danger of explosion if the battery is replaced incorrectly. Replace the battery only with the same or an equiva-
lent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer's instructions.
警告
電池更換不當會有爆炸危險。請使用製造商建議之相同或功能相當的電池更換原有電池。請按照製造商的說明指示處理
廢棄舊電池。
警告
电池更换不当会有爆炸危险。请只使用同类电池或制造商推荐的功能相当的电池更换原有电池。请按制造商的说明处理
废旧电池。
電池の取り扱い
電池交換が正しく行われなかった場合、破裂の危険性があります。 交換する電池はメーカーが推奨する型、または同等のもの
を使用下さい。 使用済電池は製造元の指示に従って処分して下さい。
경고!
배터리가 올바르게 교체되지 않으면 폭발의 위험이 있습니다. 기존 배터리와 동일하거나 제조사에서 권장하는 동등한
종류의 배터리로만 교체해야 합니다. 제조사의 안내에 따라 사용된 배터리를 처리하여 주십시오.




Note: For complete product safety information, refer to http://www.supermicro.com/about/policies/safety_information.cfm.
Product Safety Information

X12SPA-TF QUICK REFERENCE GUIDE 限用物質含有情況標示聲明書
限
限
用
用
物
物
質
質
含
含
有
有
情
情
況
況
標
標
示
示
聲
聲
明
明
書
書
設備名稱：主機板
/
Motherboard
型號（型式）：
X12SPA-TF
單元Ｕnit
限用物質及其化學符號
鉛Lead
(Pb) 汞Mercury (Hg) 鎘Cadmium (Cd)
六價鉻
Hexavalent
chromium
(Cr+6)
多溴聯苯
Polybrominated
biphenyls
(PBB)
多溴二苯醚
Polybrominated
diphenyl ethers
(PBDE)
主機板
(Motherboard)
－○○○○○
備考1.〝超出0.1 wt %〞及〝超出0.01 wt %〞係指限用物質之百分比含量超出百分比含量基準
值。
備考2.〝○〞係指該項限用物質之百分比含量未超出百分比含量基準值。
備考3.〝－〞係指該項限用物質為排除項目。
Equipment name
Type designation (Type)
Restricted substances and its chemical symbols
Declaration of the Presence Condition of the Restricted Substances Marking
Note 1：“Exceeding 0.1 wt %” and “exceeding 0.01 wt %” indicate that the percentage content of the restricted substance exceeds the
reference percentage value of presence condition.
Note 2：“○” indicates that the percentage content of the restricted substance does not exceed the percentage of reference value of presence.
Note 3：The “−” indicates that the restricted substance corresponds to the exemption.

X12SPA-TF QUICK REFERENCE GUIDE BIOS POST Codes
AMI BIOS POST Codes
About AMI BIOS POST Codes
The table below lists some of AMI BIOS POST codes for this motherboard. For more information, refer to https://www.
supermicro.com/manuals/other/AMI_AptioV_BIOS_POST_Codes_for_SM_Motherboards.pdf.
Code Description
0x32 CPU post-memory initialization is started
0x55 No Memory detected or memory failed
0x63 CPU DXE initialization is started
0x69 North Bridge DXE initialization is started
0x70 South Bridge DXE initialization is started
0x92 PCI Bus initialization is started
0x99 Super IO Initialization
0x9A USB initialization is started
0xA0 IDE initialization is started
0xA9 Boot into BIOS setup menu
0xAE Legacy Boot event
0xB2 Legacy Option ROM Initialization
0xB4 USB hot plug
0xD6 No console output devices are found
0xD7 No console input devices are found
0xF2 Recovery process started
0xF9 Recovery capsule is not found

X12SPA-TF QUICK REFERENCE GUIDE M.2 Device Installation
M.2 Device Installation
This motherboard has four M.2 M-key sockets that support M.2 2260/2280/22110 modules. One
stando󰀨 and a screw are pre-installed into the position of each 2280 mounting hole; one stando󰀨
is pre-installed into the position of each 22110 mounting hole.
Note 1: It is strongly recommended that you install a heatsink on the M.2 device or use a M.2 device
with a built-in heatsink.
Note 2: Be sure to install the M.2 device(s) prior to placing the motherboard into a chassis.
2280/22110 M.2 Device Installation
1. Locate the pre-installed screw (in the position of 2280 mounting hole). Remove the screw and
set it aside.
2. Insert the M.2 device into the M.2 socket at a 30 degree and press it down.
3. Tighten the screw to secure the M.2 device into place. Do not overtighten so as to avoid dam-
aging the M.2 device.

X12SPA-TF QUICK REFERENCE GUIDE M.2 Device Installation
2260 M.2 Device Installation
1. Locate the pre-installed stando󰀨 and screw (in the position of 2280 mounting hole). Remove
the screw and set it aside.
2. Using a hex socket screwdriver, remove and then re-install the stando󰀨 to the position of 2260
mounting hole.
3. Insert the M.2 device into the M.2 socket at a 30 degree and press it down.
4. Tighten the screw to secure the M.2 device into place. Do not overtighten so as to avoid dam-
aging the M.2 device.

X12SPA-TF QUICK REFERENCE GUIDE Memory Population
Memory Population
Note: Unbalanced memory conguration decreases memory performance and is not recommended for Supermicro
motherboards.
Intel® Optane™ Persistent Memory (PMem) 200 Series Population Table for X12SPA-TF (w/16
Slots) based on the 3rd Generation Intel Xeon Scalable (83xx/63xx/53xx/4314) Series Processors
16-DIMM Motherboard PMem Population within 1 CPU socket
DDR4+
Pmem Mode AD Inter- leave
P1-
DIMMF1
P1-
DIMMF2
P1-
DIMME1
P1-
DIMME2
P1-
DIMMH1
P1-
DIMMH2
P1-
DIMMG1
P1-
DIMMG2
P1-
DIMMC2
P1-
DIMMC1
P1-
DIMMD2
P1-
DIMMD1
P1-
DIMMA2
P1-
DIMMA1
P1-
DIMMB2
P1-
DIMMB1
4+4 AD
MM
One - x4 PMem - DDR4 - PMem - DDR4 - - DDR4 - PMem - DDR4 - PMem
One - x4 DDR4 - PMem - DDR4 - PMem - - PMem - DDR4 - PMem - DDR4
6+1 AD One - x1
DDR4 - DDR4 - - - DDR4 - - DDR4 - PMem - DDR4 - DDR4
- - DDR4 - DDR4 - DDR4 - - DDR4 - DDR4 - DDR4 - PMem
DDR4 - DDR4 - PMem - DDR4 - - DDR4 - - - DDR4 - DDR4
PMem - DDR4 - DDR4 - DDR4 - - DDR4 - DDR4 - DDR4 - -
DDR4 - DDR4 - DDR4 - - - - PMem - DDR4 - DDR4 - DDR4
DDR4 - - - DDR4 - DDR4 - - DDR4 - DDR4 - PMem - DDR4
DDR4 - DDR4 - DDR4 - PMem - - - - DDR4 - DDR4 - DDR4
DDR4 - PMem - DDR4 - DDR4 - - DDR4 - DDR4 - - - DDR4
8+1 AD One - x1
DDR4 - DDR4 - DDR4 - DDR4 - - DDR4 - DDR4 PMem DDR4 - DDR4
DDR4 - DDR4 - DDR4 - DDR4 - PMem DDR4 - DDR4 - DDR4 - DDR4
DDR4 - DDR4 PMem DDR4 - DDR4 - - DDR4 - DDR4 - DDR4 - DDR4
DDR4 - DDR4 - DDR4 - DDR4 PMem - DDR4 - DDR4 - DDR4 - DDR4
DDR4 - DDR4 - DDR4 - DDR4 - - DDR4 PMem DDR4 - DDR4 - DDR4
DDR4 - DDR4 - DDR4 - DDR4 - - DDR4 - DDR4 - DDR4 PMem DDR4
DDR4 PMem DDR4 - DDR4 - DDR4 - - DDR4 - DDR4 - DDR4 - DDR4
DDR4 - DDR4 - DDR4 PMem DDR4 - - DDR4 - DDR4 - DDR4 - DDR4
8+4 AD
MM
One - x4 DDR4 - DDR4 PMem DDR4 - DDR4 PMem PMem DDR4 - DDR4 PMem DDR4 - DDR4
Two - x2 DDR4 - DDR4 PMem DDR4 PMem DDR4 - - DDR4 PMem DDR4 PMem DDR4 - DDR4
Two - x2 DDR4 PMem DDR4 DDR4 - DDR4 PMem PMem DDR4 - DDR4 - DDR4 PMem DDR4
One - x4 DDR4 PMem DDR4 - DDR4 PMem DDR4 - - DDR4 PMem DDR4 - DDR4 PMem DDR4
8+8 AD, MM, One - x8 DDR4 PMem DDR4 PMem DDR4 PMem DDR4 PMem PMem DDR4 PMem DDR4 PMem DDR4 PMem DDR4
12+2 AD One - x2
DDR4 - DDR4 DDR4 DDR4 DDR4 DDR4 DDR4 DDR4 DDR4 DDR4 DDR4 DDR4 DDR4 - PMem
DDR4 DDR4 DDR4 DDR4 PMem - DDR4 DDR4 DDR4 DDR4 - PMem DDR4 DDR4 DDR4 DDR4
DDR4 DDR4 PMem - DDR4 DDR4 DDR4 DDR4 DDR4 DDR4 DDR4 DDR4 - PMem DDR4 DDR4
DDR4 DDR4 DDR4 DDR4 DDR4 DDR4 PMem - - PMem DDR4 DDR4 DDR4 DDR4 DDR4 DDR4

X12SPA-TF QUICK REFERENCE GUIDE Notes
Notes

X12SPA-TF
Quick RefeRence Guide Rev. 1.0b
SUPERMICR R
Motherboard Layout and Features
=mounting hole
DIMMD2
DIMMD1
DIMMB1
DIMMA2
DIMMA1
DIMMB2
DIMMC1
DIMMC2
JP4
I-SGPIO2 I-SGPIO1
J9701
J9702
JPFR1
JPFR2
JPFR3
JPME2
JPG1
JWD1
JL1
JOH1-OH
COM2
JD1
JPRG1
JSD2
+
COM1
VGA
LAN
CTRL
JPWR3
JPL1
JPUSB1
USB7/8
( USB3.2 Gen.1)
IPMI_LAN
USB5/6
( USB3.2 Gen.1 )
LAN2
JPL2
LAN
CTRL
( USB3.2 Gen.2x2)
USB4
ASM
3242
UID-SW
UID-LED
BMC
DESIGNED IN USA
X12SPA-TF
REV:1.01
BIOS LICENSE
IPMI CODE
MAC CODE
MAC CODE BAR CODE
LEDBMC (BMC Heartbeat LED)
M.2-C01 (PCI-E 4.0 X4)
PCH
12V_PUMP_PWR1
FAN4
FAN3
JPWR2
JIPMB1
(for IPMI)
BATTERY
JPWR1
JPI2C1
(PWR I2C)
SP1
LE6
M.2-C02 (PCI-E 4.0 X4)
M.2-C03 (PCI-E 4.0 X4)
M.2-C04 (PCI-E 4.0 X4)
LE5
LE4
LE3
MH14_SRW7
MH14_SRW6
MH14_SRW5
MH14_SRW4
CPU SLOT1 PCI-E 4.0 X16 CPU SLOT2 PCI-E 4.0 X8(IN X16)
CPU SLOT3 PCI-E 4.0 X16
CPU SLOT4 PCI-E 4.0 X8(IN X16)
CPU SLOT5 PCI-E 4.0 X16
CPU SLOT6 PCI-E 4.0 X8(IN X16) CPU SLOT7 PCI-E 4.0 X16
LAN1
USB9/10
JPWR4
FAN C
FAN D
HD AUDIO
AUDIO FP
JPAC1 JSPDIF_OUT
JBT1
DIMMH2
DIMMH1
DIMMF1
DIMME1
DIMMF2
DIMME2
DIMMG1
DIMMG2
FAN B FAN A
USB2/3
(
USB3.2 Gen.1 )
USB11
(
USB3.2 Gen.2 )
USB0/1
USB12
(
USB3.2 Gen.2 )
LEDPWR
(Power LED)
FAN1
FAN2
JF1
JSTBY1
(5V STBY)
JTPM1
(RAID Key Header)
JRK1
I-SATA0
I-SATA1 I-SATA3
I-SATA2 I-SATA4
I-SATA5 I-SATA6
I-SATA7
JSD1
CPU
FAN6
FAN5
JP5
I/O BACK PANEL
LGA 4189