Supero AOC-SIM1U Add-on Card User manual

Rev. 1.1a
®
SUPER
USER'S GUIDE
AOC-SIM1U/SIM1U+
Add-On Card

AOC-SIM1U/SIM1U+ User's Guide
1-2
The information in this User’s Guide has been carefully reviewed and is believed to be accurate.
The vendor assumes no responsibility for any inaccuracies that may be contained in this document,
makes no commitment to update or to keep current the information in this user's guide, or to notify
any person or organization of the updates.
Please Note: For the most up-to-date version of this user's guide, please see our
web site at www.supermicro.com.
SUPERMICRO COMPUTER reserves the right to make changes to the product described in this
user's guide at any time and without notice. This product, including software, if any, and documenta-
tion may not, in whole or in part, be copied, photocopied, reproduced, translated or reduced to any
medium or machine without prior written consent.
IN NO EVENT WILL SUPERMICRO COMPUTER BE LIABLE FOR DIRECT, INDIRECT, SPECIAL,
INCIDENTAL, OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO
USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES. IN PARTICULAR, THE VENDOR SHALL NOT HAVE LIABILITY FOR ANY
HARDWARE, SOFTWARE, OR DATASTORED OR USED WITHTHE PRODUCT, INCLUDING THE
COSTS OF REPAIRING, REPLACING, INTEGRATING, INSTALLING OR RECOVERING SUCH
HARDWARE, SOFTWARE, OR DATA.
Any disputes arising between manufacturer and customer shall be governed by the laws of Santa
Clara County in the State of California, USA. The State of California, County of Santa Clara shall
be the exclusive venue for the resolution of any such disputes. Supermicro's total liability for all
claims will not exceed the price paid for the hardware product.
WARNING: Handling of lead solder materials used in this
product may expose you to lead, a chemical known to
the State of California to cause birth defects and other
reproductive harm.
Unless you request and receive written permission from SUPER MICRO COMPUTER, Inc., you
may not copy any part of this document.
Information in this document is subject to change without notice. Other products and companies
referred to herein are trademarks or registered trademarks of their respective companies or mark
holders.
Copyright © 2012 by SUPER MICRO COMPUTER, INC.
All rights reserved.
Printed in the United States of America
User's guide Revision: Rev. 1.1a
Release Date: July 16 , 2012

1-3
Chapter 1: Introduction
Table of Contents
Chapter I: Introduction.............................................................................1-4
1.1 Overview....................................................................................................1-4
1.2 IPMI Version 2.0........................................................................................1-5
1.3 Product Features......................................................................................1-5
1.4 Checklist...................................................................................................1-5
1.5 An Important Note to the User................................................................1-5
1.6 Contacting Supermicro............................................................................1-6
&KDSWHU7HFKQLFDO6SHFL¿FDWLRQVDQG+DUGZDUH,QVWDOODWLRQ..........2-1
 7KH&RQ¿JXUDWLRQRIWKH$2&6,086,08WKH$2&86%5-.....
.........................................................................................................................2-1
$2&6,086,08&RQQHFWRUDQG-XPSHU/RFDWLRQV...................... 2-2
2.2.1 Front Components on the AOC-SIM1U(+)..............................................2-2
2.2.2 The Dedicated LAN LED on the AOC-USB2RJ45.................................. 2-2
2.2.3 Front Connectors and LED Indicators.....................................................2-3
2.2.4 Dedicated LED Indicators........................................................................2-4
2.2.5 Rear Components on the AOC-SIM1U(+)...............................................2-5
2.2.6 Rear LED Indicators................................................................................2-5
%ORFN'LDJUDP ..........................................................................................2-6
 ,QVWDOOLQJWKH$2&6,08....................................................................2-7
2.4.1 Safety Guidelines ....................................................................................2-7
2.4.2 SIM1U Slot Locations..............................................................................2-8
Chapter 3: Software Application and Usage..........................................3-1
+RPH3DJH ................................................................................................3-3
)XQFWLRQV/LVWHG2QWKH+RPH3DJH .....................................................3-5
3.2.1 Remote Control .......................................................................................3-5
3.2.2 Virtual Media............................................................................................3-7
3.2.3 System Health........................................................................................3-11
3.2.4 User Management.................................................................................3-17
3.2.5 KVM Settings.........................................................................................3-21
3.2.6 Device Settings......................................................................................3-25
3.2.7 Maintenance..........................................................................................3-38
5HPRWH&RQVROH0DLQ3DJH ..................................................................3-42
3.3.1 Remote Console Options ......................................................................3-43
Chapter 4: Frequently Asked Questions ................................................4-1

AOC-SIM1U/SIM1U+ User's Guide
1-4
Chapter 1
Introduction
This user's guide is written for system integrators, PC technicians and
knowledgeable PC users who intend to integrate Supermicro's unique IPMI 2.0
Management Utility with support of KVM-over-LAN () into their systems. It pro-
vides detailed information for the application and use of the AOC-SIM1U/SIM1U+
that supports remote access for system monitoring, diagnosis and management.
With the most advanced technologies built-in, the AOC-SIM1U/SIM1U+ offers a
FRPSOHWHHI¿FLHQWDQGFRVWHIIHFWLYHUHPRWHVHUYHUPDQDJHPHQW 
(Note: KVM-over-LAN is only for the AOC-SIM1U+ only.)
1.1 Overview
7KH$2&6,086,08 LV D KLJKO\ HI¿FLHQW KLJKO\ FRPSDWLEOH DQG HDV\WRXVH
IPMI card that allows the user to take advantage of the BMC, a baseboard man-
agement controller installed on a server motherboard and the IPMIView, an IPMI-
compliant management application software loaded in a PC, to provide serial links
between the main processor and other system components, allowing for network
interfacing via remote access. With an independent Raritan KIRA100 processor
built-in, theAOC-SIM1U/SIM1U+ provides the user with a solution to ease the com-
plex and expensive systems, allowing an administrator to access, monitor, diagnose
and manage network interfacing anywhere, anytime.
1.2 IPMI Version 2.0
The AOC-SIM1U/SIM1U+ supports the functionality of IPMI Version 2.0. The key
features include the following:
 Supports IPMI 2.0 over LAN
 Supports Serial over LAN
 Supports Virtual Media over LAN
 Supports KVM over LAN (For the AOC-SIM1U+ only)
 Supports LAN Alerting-SNMP Trap
 Supports Event Log
 Offers OS (Operating System) Independency
 Provides remote Hardware Health Monitoring via IPMI. Key features include
the following:
 Temperature monitoring
 Fan speed monitoring
 Voltage monitoring
 Power status monitoring, chassis intrusion monitoring
 Remote power control to power-on, power-off or reboot a system

1-5
Chapter 1: Introduction
 Remote access to text-based, graphic-based system information,
LQFOXGLQJ%,26FRQ¿JXUDWLRQVDQG26RSHUDWLRQLQIRUPDWLRQ.90
 Remote management of utility/software applications
 Provides Network Management Security via remote access/console redirec-
tion. Key features include:
 User authentication enhancement
 (QFU\SWLRQVXSSRUWHQKDQFHPHQWDOORZLQJIRUSDVVZRUGFRQ¿JXUD-
tion security to protect sensitive data transferring via Serial over
LAN
 Supports the following Management tools: IPMIView, CLI (Command Line
Interface) and Webengine
 Supports RMCP & RMCP protocols
1.3. Product Features
D7KH$2&6,086,086HULHV,30,ZLWKD'HGLFDWHG/$1
 6OLPVL]H:[+PP:[PP+
 6XSSRUWV,30,RYHU/$1
 6XSSRUWV8DQGDERYH
 6XSSRUWVGHGLFDWHG/$1
1.4 Checklist
If your shipping package came with missing or damaged parts, please contact
Supermicro's Tech. Support. Please refer to the following checklist when contacting
us.
i. AOC-SIM1U/SIM1U+
ii. Bracket: One bracket (SKT-0240L, including the AOC-USB2RJ45 Add-On Card,
WKH &%// &DEOH )XOO DQG /RZ 3UR¿OH ,2 %UDFNHWV 7KH 6.7/ LV
LQFOXGHGLQWKH6,08VKLSSLQJSDFNDJHRQO\
iii. CDR-SIMIPMI: One Installation CD
iv. White Box with Correct Barcode Label (showing AOC-SIM1U/SIM1U+).
1.5 An Important Note to the User
The graphics shown in this user's guide were based on the latest PCB Revision
available at the time of publishing of this guide. The SIM1U/SIM1U+ card you’ve
received may or may not look exactly the same as the graphics shown in this
user's guide.

AOC-SIM1U/SIM1U+ User's Guide
1-6
1.6 Contacting Supermicro
+HDGTXDUWHUV
Address: SuperMicro Computer, Inc.
980 Rock Ave.
San Jose, CA 95131 U.S.A.
Tel: [phone]
Fax: [phone]
Email: [email protected] (General Informaion)
[email protected] (Technical Support)
Web Site: www.supermicro.com
Europe
Address: SuperMicro Computer B.V.
Het Sterrenbeeld 28, 5215 ML
's-Hertogenbosch, The Netherlands
Tel: [phone]
Fax: [phone]
Email: [email protected] (General Information)
[email protected] (Technical Support)
[email protected] (Customer Support)
$VLD3DFL¿F
Address: SuperMicro, Taiwan
4F, No. 232-1 Liancheng Road
Chung-Ho Dist., New Taipei City 235
Taiwan, R.O.C.
Tel: [phone]
Fax: [phone]
Web Site: www.supermicro.com.tw
Email: [email protected] (Technical Support)
Tel: [phone] (Technical Support)

2-1
&KDSWHU7HFKQLFDO6SHFL¿FDWLRQVDQG,QVWDOODWLRQ
Chapter 2
7HFKQLFDO6SHFL¿FDWLRQVDQG+DUGZDUH
Installation
&RQ¿JXULQJWKH$2&6,086,08DQG 
  WKH$2&86%5-$GG2Q&DUGV  
The AOC-SIM1U/SIM1U+ Add-On Card is connected to a Dedicated LAN Ethernet
port located on the AOC-USB2RJ45 Add-On Card via an SMC Proprietary cable
(CBL-0165L) for External LAN access. One end of the CBL-0165L cable is con-
nected to the mini USB connector (J3) located on the AOC-SIM1U(+) card and the
other end to that of the AOC-USB2RJ45 card. There are two LEDs located on the
LAN port to indicate network links and activities. Refer to the picture below for the
FRQ¿JXUDWLRQ
*Note 1: You can also use LAN1 on the motherboard if you do not need the dedi-
cated LAN support. However, dedicated LAN is recommended for better graphic
support when the KVM feature is used.
*Note 2: The SKT-0240L is included in the SIM1U+ shipping package only.
$2&6,08
&%//&DEOH
$2&86%5-
'HGLFDWHG
Ethernet
/$13RUW
0LQL86%
&RQQHFWRU-
0LQL86%
Connector
%UDFNHW
/$1/('V
7KH6.7/
1RWHDERYH

AOC-SIM1U/SIM1U+ User's Guide
2-2
$2&6,086,08&RQQHFWRUDQG-XPSHU
/RFDWLRQV
5
6
)URQW&RPSRQHQWVRQWKH$2&6,08
1. V-RAM (64Mb/166MHz)
2. SDRAM (128Mb/133MHz)
3. Transformer
4. J3: Mini USB 9-pin Connector 1RWH
5. JP5: Kira 100 Processor Reset 1RWH
6. D3: Standby Power LED Indicator
7KH'HGLFDWHG/$1/(',QGLFDWRUVRQWKH$2&86%5-
8. Dedicated LAN LED Indicators
1RWH
(*Note: See Pages 2-3, 2-4 for details)
48
Front View
1
2
3
V-RAM
SDRAM SDRAM
Transformer
4
(*Note RU LQGLFDWHV3LQ
2
J3
JP5
D3

2-3
&KDSWHU7HFKQLFDO6SHFL¿FDWLRQVDQG,QVWDOODWLRQ
-0LQL86%&RQQHFWRU
There is a mini USB connector (J3) located on the
AOC-SIM1U/SIM1U+ and another mini USB con-
nector is located on theAOC-USB2RJ45. Use Cable
CBL-0165L to connect the two mini USB connectors
on both add-on cards for external LAN access. Refer
to Page 2-1 for details. See the table at right for the
SLQGH¿QLWLRQV
)URQW&RQQHFWRUDQG/(',QGLFDWRUV
Mini USB
Connector
AOC-USB2RJ45
0LQL86%3LQ'H¿QLWLRQV
-
3LQ'H¿QLWLRQ
1 Eth-TX_H
2 Eth-TX_L
3 Phy-100
4 Eth-RX_L
5 Eth-RX_H
6 Phy-ACT
7 Dedicated LAN-
Detected
8 3V-duall
9 Ground
AOC-SIM1U(+)
CBL-0165L Cable
(*Note)
-35,6&&385HVHW
JP5 is used to reset the Kira 100 Processor, NIC,
and R.T. Close Pin 1 and Pin 2 to enable this
function.After a reset or AC power-on, the AOC-
SIM1U(+)willautomaticallydetectifacable(CBL-
0165L) is connected. If a cable is not detected,
WKH$2&6,08 ZLOO WUDQVIHU WKH 5HPRWH
&RQWURO)XQFWLRQWR/$1RQWKHPRWKHUERDUG
If a cable is detected, theAOC-SIM1U(+) will use
the dedicated LAN attached to it via the mini USB
connector to manage motherboard activities via
Remote Console. See the table on the right for
jumper settings.
5,6&&385HVHW
Setting Description
Open Disabled (*Default)
Close Enabled
Dedicated LAN
port
*Note: The SKT-0240L is included in the SIM1U+ shipping package only.
7KH6.7/
1RWHEHORZ

AOC-SIM1U/SIM1U+ User's Guide
2-4
/LQN/('
Activity
/('
*/$1/LQN,QGLFDWRU
/('&RORU'H¿QLWLRQ
Off No Connection or 10 Mbps
Green 100 Mbps
*/$1$FWLYLW\,QGLFDWRU
&RORU6WDWXV'H¿QLWLRQ
Amber Flashing Active
'HGLFDWHG/$1/(',QGLFDWRUV
There are two LAN LED Indicators located
on the (Dedicated) LAN port on the AOC-
USB2RJ45 Add-On Card. The green LED
indicates activity, while the power LED may
be green or off to indicate the speed of the
Ethernet connection. See the tables on the
right for more information.
'6WDQGE\3RZHU/(',QGLFDWRU
When this LED is on, the standby power is
on. Be sure to remove power cables before
installing or removing components.
'HGLFDWHG/$1/(',QGLFDWRUV

2-5
&KDSWHU7HFKQLFDO6SHFL¿FDWLRQVDQG,QVWDOODWLRQ
Rear View
5HDU6LGHComponents
1. Raritan's Kira 100 RISC System on Chip
2. Flash Memory
3. PHY LAN
4. Heartbeat LED
1
2
3
5HDU&RPSRQHQWVRQWKH$2&6,08
4
Kira 100 Processor
PHY LAN
Flash Memory
Heartbeat LED
+HDUWEHDW/(',QGLFDWRU
Heartbeat LED, located on the rear side
of the AOC-SIM1U(+) card, indicates the
functionality and activity of the add-on
card. Heartbeat LED blinks when the
AOC-SIM1U(+) is active. However, when
the Linux OS and the drivers are being
loaded after each AC power-on or reset,
Heartbeat LED is off for about a minute.
Then, Heartbeat LED will be on again to
indicate that the AOC-SIM1U(+) is active.
See the table on the right for details.
+HDUWEHDW/('
On (Blinking) SIM1U(+): active
Off (for 1 minute) Loading Firmware
Off (Continuously) SIM1U is not active
5HDU6LGH/(',QGLFDWRUV

AOC-SIM1U/SIM1U+ User's Guide
2-6
2.3 Block Diagram
Ethernet PHY
DVO interface
UART Interface
USBInterface
LPC Interface
FML Interface
RMII
KIRA100
IPMI-200 Connector
MotherBoard SMDATA
MotherBoard SMCLK
MotherBoard SMALT#
mini USB cable
RJ45
Dedicated LAN
miniUSB
CABLE detection (Lo active)
PIN 7
GPIO24
SIM1U only

2-7
Chapter 2: Technical Specifications and Installation
2.4 Installing the AOC-SIM1U/SIM1U+
To avoid personal injury and property damage, please
carefully follow all the safety steps listed below when
installing the AOC-SIM1U(+) into your system.
ESD Safety Guidelines
Electro-StaticDischarge (ESD)can damageelectronic components.To prevent dam-
age to your system, it is important to handle it very carefully. The following measures
are generally sufficient to protect your equipment from ESD.
• Use a grounded wrist strap designed to prevent static discharge.
• Touch a grounded metal object before removing a component from the antistatic
bag.
• Handle the add-on card by its edges only; do not touch its components, peripheral
chips, memory modules or gold contacts.
• When handling chips or modules, avoid touching their pins.
• Put the card and peripherals back into their antistatic bags when not in use.
General Safety Guidelines
• Always disconnect power cables before installing or removing any components
from the computer.
• Disconnect the power cable before removing any cable from the add-on card.
• Make sure that the SIM1U(+) add-on card is securely seated in the SIM1U slot to
prevent damage to the system due to power shortage. For SIM1U slot locations,
please refer to Section 2.4.2.
SMC Motherboards with SIM1U(+) support
The following Supermicro's motherboards support the AOC-SIM1U(+).
1. The X7DB8/X7DBE/X7DB8+/X7DBE+/X7DB8-X/X7DBE-X/X7DB3 Series
2. The X7DA8/X7DAE/X7DVA-8/X7DVA-E/X7DVL-3/i Series (*Note)
3. The X7DVL-E Series
4. The PDSM4+/PDSME+ Series
(*Note: KVM-over-LAN is not supported by the X7DA8/X7DAE/X7DVL-3/i.)
2.4.1 Safety Guidelines

AOC-SIM1U/SIM1U+ User's Guide
2-8
6,086ORW/RFDWLRQV
To properly use the AOC-SIM1U(+), be sure to install it in the right slot. Refer to
the MB layouts below for SIM1U slot locations.
7KH;'%;'%(;'%;'%(;'%;;'%(;;'%6HULHVDQG
7KH;'$;'$(;'9$;'9$(;'9/L6HULHV1RWH
SIM1U(+) Slot (Slot 7)
7KH;'9/(
SIM1U(+) Slot
7KH3'603'60(6HULHV
SIM1U(+) Slot
(*Note:KVM-over-LAN isnot supportedby
the X7DA8/X7DAE/X7DVL-3/i.)

Chapter 3: Software Application and Usage
3-1
Chapter 3
Software Application and Usage
With an independent I/O processor embedded in Raritan's Kira 100 RISC System
Chip, the AOC-SIM1U/SIM1U+ Add-On Card allows the user to access, monitor,
manage and interface with systems that are in remote locations via LAN. (See the
QRWHRQ3DJH7KHQHFHVVDU\XWLOLWLHVIRUWKHDFFHVVDQGFRQ¿JXUDWLRQRIWKH
add-on card are included on the Supermicro bootable CDs that came with your
FDUG7KLVVHFWLRQSURYLGHVLQIRUPDWLRQRQWKHFRQ¿JXUDWLRQDQGWKHDFFHVVRIWKH
IPMI card on the network.
8VLQJWKH,30,&)*8WLOLW\WR&RQ¿JXUH,30$&$GGUHVVHVDQGRWKHU
IPMI Network Settings
1. Run the ipmicfg utility from the bootable CD that came with your shipment.
5HIHUWRWKHWDEOHEHORZWRFRQ¿JXUHWKH,30$&DGGUHVVHV
Board IPMI MAC IP Communication through
X7 Series SIM1U IPMI Card Available
IP/DHCP Dedicated LAN
LAN1 on MB
H8 DDR2
Memory SIM1U IPMI Card Available IP/DHCP Dedicated LAN
LAN1 on MB
H8QM3/i-x
(Note 2 below) SIM1U IPMI Card Available IP/DHCP Dedicated LAN
LAN1 LAN1 LAN1 on MB
)ROORZWKHLQVWUXFWLRQVJLYHQLQWKH5HDGPHW[W¿OHWRFRQ¿JXUH*DWHZD\,31HW-
PDVN,3DGGUHVVHVWRHQDEOHGLVDEOH'+&3DQGWRFRQ¿JXUHRWKHU,30,VHWWLQJV
Note 17KH5HDGPHW[W¿OHLVLQFOXGHGLQWKH&'WKDWFDPHZLWK\RXUVKLSPHQW$
FRS\RIWKH5HDGPHW[W¿OHGDWHGLVDOVRLQFOXGHGEHORZ
IPMICFG Version 1.04 Copyright 2007 SuperMicro Computer Inc.
Usage: IPMICFG Parameters (Example: IPMICFG -m 192.168.1.123)
-m Show IP and MAC
-m IP Set IP (format: ###.###.###.###)
-a MAC Set MAC (format: ##:##:##:##:##:##)
-k Show Subnet Mask
-k Mask Set Subnet Mask (format: ###.###.###.###)
-dhcp on Enable the DHCP
-dhcp off Disable the DHCP
-g Show Gateway IP
-g IP Set Gateway IP (format: ###.###.###.###)
Note 2)RUWKH+40LWKH$2&6,08,30,FDUGKDVWRÀDVKWKH¿UP-
ware bin from \Firmware\H8Qxx-x in the driver CD. If the AOC-SIM1U(+) IPMI card
communicates through the onboard LAN1 on the H8QM3/i-2(+), you can only use
the IPMIView Utility to access the AOC-SIM1U(+) IPMI card.

3-2
AOC-SIM1U/SIM1U+ User's Guide
7R/RJ,Q
Once you are connected to the remote server, the following Log In screen
displays.
7\SHLQ\RXU8VHUQDPHLQWKH8VHUQDPHER[
7\SHLQ\RXU3DVVZRUGLQWKH3DVVZRUGER[DQGFOLFNRQ/RJLQ
(Note: The default username is ADMIN. The default password is ADMIN.)
3. The Home Page will display as follows:
Note: KVM-over-LAN is available on theAOC-SIM1U+ only. All features and options
related to the functionality of KVM-over-LAN are supported by the AOC-SIM1U+
only. In addition, KVM-over-LAN is not supported by the following motherboards:
1. X7DA8/X7DAE
2. X7DVL-3/X7DVL-i.
7R$FFHVVWKH6,086,08&DUGIURPD&RPSXWHU
1. Choose a computer that is connected to the same network and open the
browser.
2. Type in the IP address of each server that you want to connect in the address
bar in your browser.
3. Once the connection is made, the Log In screen as shown below displays.

Chapter 3: Software Application and Usage
3-3
+RPH3DJH
%XWWRQVIURPWKH+RPH3DJH
HomeConsole Logout
Remote Console Screen
1
2
3
4
5
678
9
Function Keys
+RPH: Click this icon to return to the Home Page.
Console: Click this icon to go to the Remote Console Screen.
5HPRWH&RQVROH6FUHHQ:Displayed in the window is RemoteConsole
Screen. Click on this window to go to the Remote Console Screen.
/RJRXW: Click on this icon to log out.
1
2
3
4
5
5HIUHVK: Click on this icon to refresh the screen of the re-
mote console preview.
Power On: Click on this icon to power on the system of the
remote host.
6
7
3RZHU'RZQ: Click on this icon to power down the system
of the remote host.
5HVHW: Click on this icon to reset the remote host.
8

3-4
AOC-SIM1U/SIM1U+ User's Guide
)XQFWLRQ.H\VIURPWKH+RPH3DJH
&OLFNRQWKHVHIXQFWLRQNH\VWRXVHWKHIXQFWLRQVDVVSHFL¿HGEHORZ
(Note3OHDVHVHHWKHQH[WSDJHIRUGHWDLOVRQWKHIXQFWLRQVVSHFL¿HGDERYH
1
2
3
4
5
6
7
5HPRWH&RQWURO: Click on this icon for remote access
and management of Video Console Redirection.
2. Virtual Media: Click on this icon to use virtual remote
media devices.
6\VWHP+HDOWK: Click on this icon to view and manage
health monitoring for remote systems
4. User Management: Click on this icon for User Man-
agement.
5. KVM Settings &OLFN RQ WKLV LFRQ WR FRQ¿JXUH NH\-
board, Video and mouse settings.
'HYLFH6HWWLQJV&OLFNRQWKLVLFRQWRFRQ¿JXUHGHYLFH
settings.
7. Maintenance: Click on this icon to access, diagnose
and manage hardware devices
9

Chapter 3: Software Application and Usage
3-5
)XQFWLRQV/LVWHGRQWKH+RPH3DJH
5HPRWH&RQWURO
Click on the icon of Remote Control to activate its submenus-KVM Console and
Remote Power as listed below.
a. KVM Console
&OLFN RQ WKLV LWHP WR FRQ¿JXUH NH\ERDUG PRXVH RU YLGHR VHWWLQJV IRU WKH UHPRWH
host.
1
5HPRWH&RQVROH6FUHHQ
2
3
4
1
In the Single/Synchronized Mouse Mode, this cursor indicates the sys-
tem that is currently active. For the Double Mouse mode, this is the cur-
sor for the remote host.
2
3
This icon indicates the availability of Keyboard and Mouse.
4
This icon indicates the number of networks (users) that are connected
YLD&RQVROH5HGLUHFWLRQ7KHQXPEHURI¿JXUHLFRQVLQGLFDWHVWKHQXP-
ber of users connected.)
Explanation of Functions
This second mouse cursor only appears in the Double Mouse Mode.
This cursor represents the local mouse.

3-6
AOC-SIM1U/SIM1U+ User's Guide
E5HPRWH3RZHU
&OLFN RQ WKLV LWHP WR FRQ¿JXUH WKH SRZHU VHWWLQJV IRU 5HPRWH &RQVROH DV VKRZQ
below.
1
2 3
5HPRWH3RZHU6FUHHQ
Explanation of Functions
1
Power On: Click on this icon to power on the remote host.
3RZHU 'RZQ: Click on this icon to power down the remote
host.
2
3
5HVHW: Click on this icon to reset the remote host.