Supero Supero SAS-825TQ User manual

Rev. 2.0
SAS-825TQ Backplane
USER'S GUIDE
1
1
16
32
48
BAR CODE
REV 2.0
SAS825TQ
1
GNDGND+12V +5VGNDGND+12V +5V
#2
I C
#1
ACT_IN
JP29:9072 RESET
I C
SIDEBAND #2
SIDEBAND #1
2
2
+
++
++ ++
+
+
+
++
+
+
1
1
1
16
32
48
GNDGND+12V +5VGNDGND+12V +5V
+
+
+
BAR CODE
+
+
+
REV 2.0
SAS825TQ
#2
2
I C
#1
ACT_IN
JP29:9072 RESET
2
I C
SIDEBAND #2
SIDEBAND #1
+
++
++ ++
+
SUPER ®

SAS-825TQ Backplane User’s Guide
Manual Revision 2.0
Release Date: June 10, 2013
The information in this User’s Manual has been carefully reviewed and is believed to be accurate.
The vendor assumes no responsibility for any inaccuracies that may be contained in this document,
makes no commitment to update or to keep current the information in this manual, or to notify any
person or organization of the updates. Please Note: For the most up-to-date version of this
manual, please see our web site at www.supermicro.com.
Super Micro Computer, Inc. ("Supermicro") reserves the right to make changes to the product
described in this manual at any time and without notice. This product, including software and
documentation, is the property of Supermicro and/or its licensors, and is supplied only under a
license. Any use or reproduction of this product is not allowed, except as expressly permitted by
the terms of said license.
IN NO EVENT WILL SUPERMICRO BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL,
SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO
USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES. IN PARTICULAR, SUPERMICRO SHALL NOT HAVE LIABILITY FOR ANY
HARDWARE, SOFTWARE, OR DATA STORED OR USED WITH THE PRODUCT, INCLUDING THE
COSTS OF REPAIRING, REPLACING, INTEGRATING, INSTALLING OR RECOVERING SUCH
HARDWARE, SOFTWARE, OR DATA.
Any disputes arising between manufacturer and customer shall be governed by the laws of Santa
Clara County in the State of California, USA. The State of California, County of Santa Clara shall
be the exclusive venue for the resolution of any such disputes. Super Micro's total liability for all
claims will not exceed the price paid for the hardware product.
California Best Management Practices Regulations for Perchlorate Materials: This Perchlorate
warning applies only to products containing CR (Manganese Dioxide) Lithium coin cells. “Perchlorate
Material-special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate”
WARNING: Handling of lead solder materials used in this
product may expose you to lead, a chemical known to
the State of California to cause birth defects and other
reproductive harm.
Unless you request and receive written permission from Super Micro Computer, Inc., you may not
copy any part of this document.
Information in this document is subject to change without notice. Other products and companies
referred to herein are trademarks or registered trademarks of their respective companies or mark
holders.
Copyright © 2013 by Super Micro Computer, Inc.
All rights reserved.
Printed in the United States of America

Preface
iii
Table of Contents
Contacting Supermicro.......................................................................................iv
Returning Merchandise for Service.....................................................................v
Chapter 1 SAS-825TQ Safety Guidelines
1-1 ESD Safety Guidelines ................................................................................... 1-1
1-2 General Safety Guidelines .............................................................................. 1-1
1-3 An Important Note to Users ............................................................................ 1-2
1-4 Introduction to the SAS-825TQ Backplane..................................................... 1-2
Chapter 2 Connectors, Jumpers and Pin Denitions
2-1 Front Connectors and SAS Ports ................................................................... 2-1
Front Connectors ............................................................................................ 2-1
SAS Ports........................................................................................................ 2-1
2-2 FrontConnectorandPinDenitions............................................................... 2-2
2-3 FrontJumperLocationsandPinDenitions................................................... 2-4
Explanation of Jumpers .................................................................................. 2-4
SGPIO and I2C Modes and Jumper Settings ................................................. 2-5
SAS Port Connections in I2C and SGPIO Settings ....................................... 2-7
Front LED Indicators ....................................................................................... 2-7
2-4 Rear Connectors and LED Indicators............................................................. 2-8

SAS-825TQ Backplane User’s Guide
iv
Contacting Supermicro
Headquarters
Address: Super Micro Computer, Inc.
980 Rock Ave.
San Jose, CA 95131 U.S.A.
Tel: [phone]
Fax: [phone]
Email: [email protected] (General Information)
[email protected] (Technical Support)
Web Site: www.supermicro.com
Europe
Address: Super Micro Computer B.V.
Het Sterrenbeeld 28, 5215 ML
's-Hertogenbosch, The Netherlands
Tel: [phone]
Fax: [phone]
Email: [email protected] (General Information)
[email protected] (Technical Support)
[email protected] (Customer Support)
Asia-Pacic
Address: Super Micro Computer, Inc.
3F, No. 150, Jian 1st Rd.
Zhonghe Dist., New Taipei City 23511
Taiwan (R.O.C)
Tel: [phone]
Fax: [phone]
Web Site: www.supermicro.com.tw
Technical Support:
Email: [email protected]
Tel: [phone]

Preface
v
Returning Merchandise for Service
A receipt or copy of your invoice marked with the date of purchase is required be-
fore any warranty service will be rendered. You can obtain service by calling your
vendor for a Returned Merchandise Authorization (RMA) number. When returning
to the manufacturer, the RMA number should be prominently displayed on the
outside of the shipping carton, and mailed prepaid or hand-carried. Shipping and
handling charges will be applied for all orders that must be mailed when service
is complete.
For faster service, RMA authorizations may be requested online (http://www.super-
micro.com/support/rma/).
Whenever possible, repack the backplane in the original Supermicro box, using the
original packaging materials. If these are no longer available, be sure to pack the
backplane in an anti-static bag and inside the box. Make sure that there is enough
packaging material surrounding the backplane so that it does not become damaged
during shipping.
This warranty only covers normal consumer use and does not cover damages in-
curred in shipping or from failure due to the alteration, misuse, abuse or improper
maintenance of products.
Duringthewarrantyperiod,contactyourdistributorrstforanyproductproblems.

SAS-825TQ Backplane User’s Guide
vi
Notes

1-1
Chapter 1: Safety Guidelines
Chapter 1
SAS-825TQ Safety Guidelines
To avoid personal injury and property damage, carefully follow all the safety steps
listed below when accessing your system or handling the components.
1-1 ESD Safety Guidelines
Electrostatic Discharge (ESD) can damage electronic components. To prevent dam-
age to your system, it is important to handle it very carefully. The following measures
are generally sufcient to protect your equipment from ESD.
•Use a grounded wrist strap designed to prevent static discharge.
•Touch a grounded metal object before removing a component from the antistatic
bag.
•Handle the backplane by its edges only; do not touch its components, peripheral
chips, memory modules or gold contacts.
•When handling chips or modules, avoid touching their pins.
•Put the card and peripherals back into their antistatic bags when not in use.
1-2 General Safety Guidelines
•Always disconnect power cables before installing or removing any components
from the computer, including the SAS-825TQ backplane.
•Disconnect the power cable before installing or removing any cables from the
SAS-825TQ backplane.
•Make sure that the SAS-825TQ backplane is securely and properly installed on
the motherboard to prevent damage to the system due to power shortage.

1-2
SAS-825TQ Backplane User's Guide
1-3 An Important Note to Users
All images and layouts shown in this user's guide are based upon the latest PCB
Revision available at the time of publishing. The card you have received may or
may not look exactly the same as the graphics shown in this manual.
1-4 Introduction to the SAS-825TQ Backplane
The SAS-825TQ backplane has been designed to utilize the most up-to-date tech-
nology available, providing your system with reliable, high-quality performance.
ThismanualreectsSAS-825TQRevision2.0,themostcurrentreleaseavailableat
the time of publication. Always refer to the Supermicro Web site at www.supermicro.
comforthelatestupdates,compatiblepartsandsupportedcongurations.

2-1
Chapter 2: Safety Guidelines
1
1
16
32
48
BAR CODE
REV 2.0
SAS825TQ
1
GNDGND+12V +5VGNDGND+12V +5V
#2
I C
#1
ACT_IN
JP29:9072 RESET
I C
SIDEBAND #2
SIDEBAND #1
2
2
+
++
++ ++
+
+
+
++
+
+
1
1
1
16
32
48
GNDGND+12V +5VGNDGND+12V +5V
+
+
+
BAR CODE
+
+
+
REV 2.0
SAS825TQ
#2
2
I C
#1
ACT_IN
JP29:9072 RESET
2
I C
SIDEBAND #2
SIDEBAND #1
+
++
++ ++
+
1
1
16
32
48
BAR CODE
REV 2.0
SAS825TQ
1
GNDGND+12V +5VGNDGND+12V +5V
#2
I C
#1
ACT_IN
JP29:9072 RESET
I C
SIDEBAND #2
SIDEBAND #1
2
2
+
++
++ ++
+
+
+
++
+
+
1
1
1
16
32
48
GNDGND+12V +5VGNDGND+12V +5V
+
+
+
BAR CODE
+
+
+
REV 2.0
SAS825TQ
#2
2
I C
#1
ACT_IN
JP29:9072 RESET
2
I C
SIDEBAND #2
SIDEBAND #1
+
++
++ ++
+
Chapter 2
Connectors,JumpersandPinDenitions
2-1 Front Connectors and SAS Ports
Front Connectors SAS Ports
1
1
1
9
1
7
1
31
41
51
61
8
1
2
1
10
1
14
1
17
1
13
1
16
1
19
1
11
1
12
1
15
1
18
Figure 2-1: Front Connectors
Figure 2-2: Front SAS Ports
1. 4-pin power connector: JP13
2. 4-pin power connector: JP10
3. CD-ROM/oppyconnector:JP18
4. CD-ROM/oppyconnector:JP17
5. SAS activity LED header: JP26
6. I2C connector #2: JP45
7. I2C connector #1: JP44
8. Sideband connector #2: JP52
9. Sideband connector #1: JP51
10. MG9072 chip
11. Upgrade header: JP46
12. SAS Port #0
13. SAS Port #1
14. SAS Port #2
15. SAS Port #3
16. SAS Port #4
17. SAS Port #5
18. SAS Port #6
19. SAS Port #7

2-2
SAS-825TQ Backplane User's Guide
Backplane
Main Power
4-Pin Connector
Pin#Denition
1+12V
2 and 3 Ground
4 +5V
CD-ROM/FDD Power
4-Pin Connector
Pin#Denition
1+5V
2 and 3 Ground
4 +12V
#1 and #2 Backplane Main Power Connec-
tors
The 4-pin connectors, designated JP10, and
JP13 provide power to the backplane. See
thetableontherightforpindenitions.
#3 and #4 CD-ROM/Floppy Pin Connectors
Pin connectors designated J17 and J18,
provide power to the CD-ROM and oppy
drives. See the table on the right for pin
denitions.
2-2 FrontConnectorandPinDenitions
SAS Activity LED Header
PinDenitions
Pin#Denition Pin#Denition
1 ACT IN#0 6 ACT IN#4
2 ACT IN#1 7 ACT IN#5
3 ACT IN#2 8 ACT IN#6
4 ACT IN#3 9 ACT IN#7
5 Ground 10 Empty
#5 Activity LED Headers
The activity LED header, designated JP26
is used to indicate the activity status of
each SAS drive. The activity LED header is
located on the front panel. For the activity
lead header to work properly, connect to it
using a 10-pin LED cable. This is only used
when the activity LED is not supported by
the hard drive.
#6 and #7 I2C Connectors
The I2C Connectors, designated JP44 and
JP45, are used to monitor the HDD activity
and status. See the table on the right for pin
denitions.
I2C Connector
PinDenitions
Pin#Denition
1 Data
2 Ground
3 Clock
4 No Connection

2-3
Chapter 2: Safety Guidelines
#8 and #9 Sideband Headers
The sideband headers are designated JP51
and JP52. For SES-2 to work properly, you
must connect an 8-pin sideband cable. See
thetabletotherightforpindenitions.
Sideband Headers
Pin#Denition Pin#Denition
2 SGPIO:
SDIN;
I2C:
Backplane
Addressing
1 Controller
ID (SB6)
4 SGPIO:
SDOUT;
I2C: Reset
3 GND (SB2)
6 GND (SB3) 5 SGPIO:
SLOAD;
I2C: SDA
8 Backplane
ID (SB7)
7 SGPIO:
SCLOCK;
12C: SCL
10 No Connec-
tion
9 No Connec-
tion
#12 to #19 SAS Ports
The SAS ports are used to connect the SAS
drive cables. The eight ports are designated
#0 - #7. Each port is also compatible with
SATA drives.
#10 MG9072 Chip
The MG9072 is an enclosure management
chip that supports the SES-2 controller and
SES-2 protocols.
#11 Upgrade Header
The upgrade header is designated JP46 and is
used for manufacturing purposes only.

2-4
SAS-825TQ Backplane User's Guide
1
1
16
32
48
BAR CODE
REV 2.0
SAS825TQ
1
GNDGND+12V +5VGNDGND+12V +5V
#2
I C
#1
ACT_IN
JP29:9072 RESET
I C
SIDEBAND #2
SIDEBAND #1
2
2
+
++
++ ++
+
+
+
++
+
+
1
1
1
16
32
48
GNDGND+12V +5VGNDGND+12V +5V
+
+
+
BAR CODE
+
+
+
REV 2.0
SAS825TQ
#2
2
I C
#1
ACT_IN
JP29:9072 RESET
2
I C
SIDEBAND #2
SIDEBAND #1
+
++
++ ++
+
2-3 FrontJumperLocationsandPinDenitions
Explanation of Jumpers
To modify the operation of the backplane,
jumpers can be used to choose between
optional settings. Jumpers create shorts
between two pins to change the function
of the connector. Pin 1 is identied with
a square solder pad on the printed circuit
board. Note: On two pin jumpers, "Closed"
means the jumper is on and "Open" means
the jumper is off the pins.
Connector
Pins
Jumper
Setting
3 2 1
3 2 1
Jumper Settings
Jumper Jumper Settings Note
JP29 Open (Jumper off the pins): Default
Closed (Jumper on the pins): Reset
MG9072 chip reset
JP18 Open (Jumper off the pins): Default
Closed (Jumper on the pins): Reset
Buzzer reset*
Figure 2-3: Front Jumpers
*The buzzer sound indicates that a condition requiring immediate attention has
occurred.
The buzzer alarm is triggered by the following conditions:
1. Hard drive failure
2. System temperature over 45º Celsius.
JP18 JP29
JP50
JP37
JP38 JP34
JP36
JP43
JP33
JP42
JP41
JP40
Closed, jumper on
Open, jumper off
the pins.
the pins.

2-5
Chapter 2: Safety Guidelines
SGPIO and I2C Modes and Jumper Settings
This backplane can utilize SGPIO or I2C, which is the default mode and can be
used without making changes to your jumpers. The following information describes
whichjumpermustbeconguredtouseSGPIOmode.
SGPIO Settings
Jumper Jumper Setting Notes
JP33 1-2 Controller ID #1
JP34 1-2 Backplane ID #1
1-2: ID#0
JP36 1-2 Controller ID #2
JP37 1-2 Backplane ID #2
1-2: ID#0
JP38 Open (Jumper off the pins) I2C Reset #2
JP40 Closed (Jumper on the pins) I2C Reset_SDOUT#1
JP41 Closed (Jumper on the pins) I2C Reset_SDOUT#2
JP42 1-2 I2C Backplane ID_SDIN#1
JP43 1-2 I2C Backplane ID_SDIN#2
JP50 Open (Jumper off the pins) I2C Reset #1

2-6
SAS-825TQ Backplane User's Guide
I2C Settings (Default)
Jumper Jumper Setting Notes
JP33 2-3 Controller ID #1
JP34 1-2
Backplane ID #1
1-2: ID#0
2-3: ID#1
JP36 2-3 Controller ID #2
JP37 2-3
Backplane ID #2
1-2: ID#0
2-3: ID#1
JP38 Closed (Jumper on the pins) I2C Reset #2
JP40 Open (Jumper off the pins) I2C Reset_SDOUT#1
JP41 Open (Jumper off the pins) I2C Reset_SDOUT#2
JP42 2-3 I2C Backplane ID_SDIN#1
JP43 2-3 I2C Backplane ID_SDIN#2
JP50 Closed (Jumper on the pins) I2C Reset #1

2-7
Chapter 2: Safety Guidelines
SAS Port Connections in I2C and SGPIO Settings
Use the following chart when connecting this backplane. If the SAS ports are con-
nected out of order, it is not easy to identify drives using the LED function.
SAS Port Connections in I2C and SGPIO Settings
Port # I2C SGPIO
# 0 - 3 I2C #1 Sideband #1
# 4 - 7 I2C #2 Sideband #2
Front Panel LEDs
LED State Specication
D3 On Overheat/drive failure LED indicator.
(Red light: Flashing. Buzzer: On, if activated)
Front LED Indicators
Figure 2-4: Front LED
1
1
16
32
48
BAR CODE
REV 2.0
SAS825TQ
1
GNDGND+12V +5VGNDGND+12V +5V
#2
I C
#1
ACT_IN
JP29:9072 RESET
I C
SIDEBAND #2
SIDEBAND #1
2
2
+
++
++ ++
+
+
+
++
+
+
1
1
1
16
32
48
GNDGND+12V +5VGNDGND+12V +5V
+
+
+
BAR CODE
+
+
+
REV 2.0
SAS825TQ
#2
2
I C
#1
ACT_IN
JP29:9072 RESET
2
I C
SIDEBAND #2
SIDEBAND #1
+
++
++ ++
+
D3

2-8
SAS-825TQ Backplane User's Guide
R156 R155
D8
D7
D6
D5
D26
D23
D20
D19
D25
D22
D21
D18
D15
D14
D13 D12
C106
+
+ + +
+
+ + +
+
+ +
+
+
+ + +
FAIL1
ACT0FAIL0
ACT2FAIL2
ACT1
FAIL4
ACT3FAIL3
ACT5FAIL5 ACT4
FAIL6 ACT6
ACT7
FAIL7
2-4 Rear Connectors and LED Indicators
Rear SAS/SATA Connectors
Rear
Connector
SAS Drive
Number
Rear
Connector
SAS Drive
Number
SAS #0 J1 SAS/SATA HDD #0 SAS #4 J9 SAS/SATA HDD #4
SAS #1 J2 SAS/SATA HDD #1 SAS #5 J11 SAS/SATA HDD #5
SAS #2 J3 SAS/SATA HDD #2 SAS #6 J13 SAS/SATA HDD #6
SAS #3 J4 SAS/SATA HDD #3 SAS #7 J15 SAS/SATA HDD #7
Rear LED Indicators
Rear LED Hard Drive Activity Failure LED
SAS #0 D12 D5
SAS #1 D13 D6
SAS #2 D14 D7
SAS #3 D15 D8
SAS #4 D18 D19
SAS #5 D21 D20
SAS #6 D22 D23
SAS #7 D25 D26
D15
D8
SAS #3
J4
D26
D25
SAS #7
J15
D22
D23
SAS #6
J13
D21
D20
SAS #5
J11
D18
D19
SAS #4
J9 D14
D7
SAS #2
J3
D13
D6
SAS #1
J2
D12
D5
SAS #0
J1
Figure 2-5: Rear Connectors and LEDs

2-9
Chapter 2: Safety Guidelines
Notes

2-10
SAS-825TQ Backplane User's Guide
Disclaimer (cont.)
The products sold by Supermicro are not intended for and will not be used in life sup-
port systems, medical equipment, nuclear facilities or systems, aircraft, aircraft devices,
aircraft/emergency communication devices or other critical systems whose failure to per-
formbereasonablyexpectedtoresultinsignicantinjuryorlossoflifeorcatastrophic
property damage. Accordingly, Supermicro disclaims any and all liability, and should
buyer use or sell such products for use in such ultra-hazardous applications, it does so
entirely at its own risk. Furthermore, buyer agrees to fully indemnify, defend and hold
Supermicro harmless for and against any and all claims, demands, actions, litigation,
and proceedings of any kind arising out of or related to such ultra-hazardous use or
sale.