Suptek MD6843 User manual

MD6843
Step 5 Adjust the Angle of Monitor
Step 3 Attach the VESA Plate to the Monitor
Step 6 Manage the Wires and Store the Allen Keys on Wire Clip
Step 4 Mount the Monitor on the Rotating Arm
Fixed on the back of the monitor Secure the back of the monitor
with a washer
Insert the monitor into the head
of the rotating arm
Screw and lock the monitor with
screws
Adjust the head of the monitor
as necessary to prevent the head
of the monitor from sagging
Thank you for choosing our products!
qs
r
h
o
d
Use the supplied Allen Key(o) to do the necessary adjustment.
The wire is fixed with a clamp (n1).
o
The height of the monitor can be
adjusted by adjusting the tightness
of screw
o
o
UNPACKING INSTRUCTIONS
Carefully open the carton, remove contents and lay out on cardboard or other
protectivesurface to avoid damage.
Check package contents against the Supplied Parts List in the next page to assure thatall
components wete received undamaged. Do not use damaged or defective parts.
Carefully read all instructions before attempting installation.
IMPORTANT SAFETY INFORMATION
Install and operate this device with care. Please read this instruction before installation,
and carefully follow all instructions contained herein. Use proper safety equipment during
installation.
Please call a qualified installation contractor for help if you don’t understand these
directions or have any doubts about the safety of the installation.
Do not use this product for any purpose or in any configuration not explicitly specified in
this instruction. We hereby disclaims any and all liability for injury or damage arising from
incorrect assembly, incorrect mounting, or incorrect use of this product.
Installation instruction

(2) Pole-a (1) Clamp-b (1) Clamp Brace-c (1) Swivel Arm-d
(3) VESA Plate-e (3) M5X16 Bolt-f (2) M8X12Bolt-g (3) Nut-h
(1) Grommet Base Plate
-m
(2) Wire Clip-n1 (4)Wire Clip-n2 (1) Allen Key-o
(1) M10 Bolt -i (1) Support Plate-j (1) M10 Washer-k (1) Spring Washer-l
(1) Wrench-p
(12) M4X12Bolt-q (12) M4X30 Bolt-r (12) M8Spacer-s
WARNING
CAUTION!
This monitor desktop mount must be securely
attached to the horizontal desk. If the mount is
not properly installed it may fall, resulting in
possible injury and/or damage!
Supplied Parts List Step 1 Install the Pole to the Desktop
Step 2 Install Arm to the Pole
Option A: Desk Clamp Install
1.Install the Clamp Brace(c) to the Pole(a),
Using 3pcs M5x16 Bolts(f), and tighten using
the ALLen Key(o) , see Figure 1.
2.Install the Clamp(b) to the pole assembly according
to the thickness of the desktop. The thickness can be
changed of three positions. Connect it using 2 pcs
M8x12 Bolts(g), and tighten using the Allen Key(o).
Tighten with the Allen Key-o. See Figure 2
Figure 2
Option B: Grommet Base Install
Existing Grommet Hole Installation
If the existing grommet hole comes with a plastic
protector, remove it to ensure a flat surface before
installing the desk mount.
,
1. Mounting base (m)
Pole (a) is tightened with 3 M5x16 bolts (f) and an
Allen Key(o), see Figure 3.
2.Position the Pole(a) on the mounting surface and
secure using the Suport Plate(j), M10 Washer(k),
Spring Washer(I), and M10 Bolt(i). Fasten the
M10 Bolt using provided Wrench(p), see Figure 4.
Option B: Grommet Base Install
Self Drilled Grommet Hole Installation
1. Punch a 10MM hole in the table to install the lock hole.
2. Install the Grommet Base Plate(m) to the Pole(a)
using 3pcs M5x16 Bolts(f), and tighten using the
Allen Key(o), see Figure 5.
3. Position the Pole(a) on the mounting surface
and secure using the Support Plate(j).
M10 Washer(k), Spring Washer(l) and
M10 Bolt(i), Fasten the M10 Bolt using
provided Wrench(p), see Figure 6.
a
m
f
Figure 1
Figure 3
Figure4
Figure 5
Figure 6
j
k
l
i
a
m
f
j
k
l
i
a
c
f
g
o
b
Plastic Knob
d
on1
n2
u
Install Swivel Arm(d) to the Pole.
Fasten the bolt with supplied Allen Key(o).
Tools Required Phillips Screwdriver
(3) M5X16Bolt-t
Rotate two poles into one.
Tighten the stud screws with
a wrench after tightening.
(1) Single connector -u
Step 1 Install the Pole to the Desktop