
a
c
f
g
o
b
(2) Pole-a (1) Clamp -b (1) Clamp Brace -c (1) Swivel Arm-d
(4) VESA Plate -e (3) M5X16 Bolt -f (2) M8X12 Bolt -g (4) Nut -h
(2) Wire Clip -n1 (6) Wire Clip-n2 (1) Allen Key -o
(1) M10 Bolt -i (1) Support Plate -j (1) M10 Washer -k (1) Spring Washer -l
(1) Wrench-p (16) M4X12 Bolt -q (16) M4X30 Bolt -r (16) M8Spacer-s (2) head sleeve -t
n1
t
o
d
n2
(3) M5X16 Bolt-u
Step 1 Install the Pole to the Desktop
Option B: Grommer Base Install
Self Drilled Grommet Hole Installation
1. Position the Pole(a) on the mounting
surface and amark the center hole. Drill a 3/8”
(10mm) diameter hole at the marked position
through the mounting surface.
2. Install the Grommet Base Plate(m) to the
Pole(a) using 3pcs M5x16 Bolts(f), and
tighten using the Allen Key(o), see Fihure 5.
3. Position the Pole(a) on the mounting
surface and secure using the Support Plate
(j). M10 Washer(k), Spring Washer(l) and
M10 Bolt(i), Fasten the M10 Bolt using
provided Wrench(p), see Figure 6.
a
m
fFigure 5
Figure 6
j
k
l
i
Step 2 Install Arm to the Pole
Place the Head Sleeve(t) and Swivel Arm(d) over the pole,
and tighten with Allen Key(o)
Option A: Desk Clamp Install
Step 1 Install the Pole to the Desktop
Figure 2
Figure 1
1. Install the “c”-Clamp Brace(c) to the Pole
(a) using 3pcs M5x16 Bolts(f), and tighten
using the ALLen Key(o) , see Fihure 1.
2. Install the “c”-Clamp(b) to the pole
assembly according to the thickness of the
desktop. The thickness can be changed of
three positions. Connect it using 2 pcs M8x12
Bolts(g), and tighten using the Allen Key(o).
Tighten the “c”-Clamp to the desktop using
the plastic knob, see Figure 2.
Plastic Knob
Tighten and splice
two poles into one,
then tighten the stud
with wrench to secure
Option B: Grommet Base Install
Existing Grommet Hole Installation
If the existing grommet hole comes with a
plastic protector, remove it to ensure a flat
surface before installing the desk mount.
1. Install the Grommet Base Plate(m) to the
Pole(a) using 3 pcs M5x16 Bolts(f) , and
tighten using the Allen Key(o), see Fihure 3.
2. Position the Pole(a) on the mounting
surface and secure using the Suport Plate
(j), M10 Washer(k), Spring Washer(I), and
M10 Bolt(i). Fasten the M10 Bolt using
provided Wrench(p), see Fihure 4.
Figure 3
Figure 4
a
m
f
j
k
l
i
WARNING
CAUTION!
This monitor desktop mount must be securely
attached to the horizontal desk. If the mount is
not properly installed it may fall, resulting in
possible injury and/or damage.
Tools Required Phillips Screwdriver
Supplied Parts List
(1) Grommet Base
Plate-m