Suptek MD6821 User manual

(2) pole-a (1) clamp-b (1) clamp brace-c (1) swivel arm-d
(1) VESA plate-e (3) M5x16 bolt-f (2) M8x12 bolt-g (1) nut-h
(2) wire clip-n1 (2) wire clip-n2 (1) allen key-o
(1) M10 bolt-i (1) support plate-j (1) M10 washer-k (1) spring washer-l
(1) wrench-p (4) M4X12 bolt-q (4) M4X30 bolt-r (8) M8 spacer-s
(3) M5X16 bolt-t
Self Drilled Grommet Hole Installation
Step 1 Install the pole to the desktop
Option A: desk clamp install
Option B: grommet base install
Existing grommet hole installation
figure 3 a
m
f
figure 4
j
k
l
i
figure 5 a
m
f
figure 6
j
k
l
i
figure 2
g
o
b
plastic knob
(1) grommet base
plate-m
Tools Required
Phillips Screwdriver
MD6821
INSTALLATION MANUAL
figure 1
a
c
f
UNPACKING INSTRUCTIONS
·Carefully open the carton, remove contents and lay out on cardboard or
other protective surface to avoid damage.
·Check package contents against the supplied parts list in the next page
to assure that all components wete received undamaged. Do not use
damaged or defective parts.
·Carefully read all instructions before attempting installation.
IMPORTANT SAFETY INFORMATION
·Install and operate this device with care. Please read this instruction
before installation, and carefully follow all instructions contained herein.
Use proper safety equipment during installation.
·Please call a qualified installation contractor for help if you don’t
understand these directions or have any doubts about the safety of the
installation.
Do not use this product for any purpose or in any configuration not
explicitly specified in this instruction. We hereby disclaims any and all
liability for injury or damage arising from incorrect assembly, incorrect
mounting, or incorrect use of this product.
Supplied parts list
WARNING
CAUTION!
This monitor desktop mount must be securely
attached to the horizontal desk. If the mount isnot
properly installed it may fall, resulting in possible
injury and/or damage.
If the existing grommet hole comes with a plastic
protector, remove it to ensure a flat surface before
installing the desk mount.
1. Install the grommet base plate (m)
to the pole (a) using 3 pcs M5x16
bolts (f) , and tighten using the allen
key (o), see figure 3.
2. Position the pole (a) on the
mounting surface and secure using
the suport plate (j), M10 Washer (k),
spring washer (I), and M10 bolt (i).
fasten the M10 bolt using provided
wrench (p), see figure 4.
1. Position the pole (a) on the
mounting surface and amark the
center hole. Drill a 3/8”(10mm)
diameter hole at the marked position
through the mounting surface.
2. Install the grommet base plate (m) to
the pole(a) using 3 pcs M5x16 bolts (f),
and tighten using the allen key (o), see
figure 5.
3. Position the pole (a) on the mounting
surface and secure using the support
plate (j). M10 washer (k), spring washer
(l) and M10 bolt (i), fasten the M10 bolt
using provided wrench (p), see figure 6.
2. Install the “c”-clamp (b) to the pole
assembly according to the thickness of
the desktop. The thickness can be
changed of three positions. Connect it
using 2 pcs M8x12 bolts (g), and tighten
using the allen key (o).Tighten the
“c”-clamp to the desktop using the
plastic knob, see figure 2.
1. Install the “c”-clamp brace (c) to the
pole (a) using 3pcs M5x16 bolts (f), and
tighten using the allen key (o) , see figure
1.

Install arm to the pole
Place the swivel arm (d) over the pole,
and tighten with allen key (o).
o
o
Make the necessary adjustments
Adjust and tighten the
bolt with the supplied
allen key (o) to fix the
tilt angle.
By adjusting the
tightness of the screws,
the height of the monitor
can be adjusted.
Manage the wires and store the allen
keys on wire clip
Step 2
qs
r
Attach the VESA plate to the monitor
For Monitor with Flat Back For monitor with curved or
recessed back
Step 3
h
d
Slide the monitor to the head of swivel arm
Step 4
Install the security nut (h). Make
sure the security nut is
installedbefore you rotate the
monitor.
Slide the monitor onto the head of
swivel arm (d) as the above
diagram.
Step 5 Step 6
Thank you for choosing our products!