SVP HDT-04 User manual

HDT-04
HIGH POWER
TRANSMITTER
USER´S MANUAL V9.9

Accessories included in this manual
AVS
Airborne Antenna
GPS-02
Antenna
RTC-01
Remote Control
RTC-02
Remote Control

3
HDT-04 High Power Transmitter
USER’S MANUAL V9.9
Contents
Chapter 1: Introduction
This first chapter provides a general description of the HDT-04 high power
transmitter.
Chapter 2: Technical features
This second part offers the transmitter’s physical and environmental
characteristics.
Chapter 3: How to order
The third part provides the user with information on ordering and different
configurations available for these Transmitters.
Chapter 4: Transmitter operation and Menus
This third part provides the user all the necessary information to control and
operate the equipment properly. It is detailed the function of each button on
the keyboard and the information shown on the display, menus, etc.
Chapter 5: GPS Application
In this chapter, the use of the GPS incorporated system and some of its
applications are shown.
Chapter 6: Web Server and SNMP
This chapter provides a detailed description of the Web Server tool. This
feature allows controlling the HDT-04 transmitter through a website.
Chapter 7: Block Diagram
This chapter provides a block diagram of the HDT-04 transmitter internal
performance.
Chapter 8: Equipment Installation
This seventh chapter indicates the available connections of the transmitter
and their characteristics.
Chapter 9: Remote Control
The use of the RTC-01 and RTC-02 device provides a remote connection to
the HDT-04 transmitter.
Chapter 10: Mechanical Dimensions
In this chapter, the mechanical drawing of the units described in this manual
are included.
Chapter 11: Preventive maintenance
This chapter explain the procedure that should be followed during the
transmitter's life.
Chapter 12: Warranty
This chapter contains warranty considerations and conditions.

4
HDT-04 High Power Transmitter
USER’S MANUAL V9.9
Index A: AVS Airborne Antenna User’s Guide
Index B: GPS User’s Guide
Index C: Modulation Standards

5
HDT-04 High Power Transmitter
USER’S MANUAL V9.9
Dear customer,
We would like to thank you for selecting this equipment and welcome you to
the SVP’s growing family of products.
We are sure that the addition of this equipment will cause you a complete
satisfaction in your existing installation.
Please read these instructions carefully, and keep them in hand in case you
have to refer to them.

6
HDT-04 High Power Transmitter
USER’S MANUAL V9.9
About this manual
This user’s guide provides indications and explanations about how to set up
the HDT-04 transmitter easily for the most common use cases.
This document is intended to help first time users:
-To find their way around the GUI.
-To understand the different possibilities of the HDT-04 transmitter.
-To configure the HDT-04 for their specific configurations.
Symbols
The symbols that appear in this manual are:
An information message which indicates explanations for the
proper operation of the equipment.
This symbol advises users that if they do not take, avoid or make
specific actions, several damages could appear in the device.
In the places where this symbol appears it means that by
pressing the Down button of the equipment the user can access
to the next screen.
This symbol means that pressing the OK button in the options
where this symbol appears, the user can access to the submenu
related to that option or can change the value of the
parameter.
<> These symbols mean that the parameter can be modified in the
same screen with the right and left keys.

7
HDT-04 High Power Transmitter
USER’S MANUAL V9.9
Important Notes
1. The HDT-04 transmitter is completely compatible with the DVB-T/T2
Standards, included in the European Standard ETSI EN300744 (DVB-T),
ETSI EN300755 (DVB-T2). It also complies with the ISDB-T International
technical standard (optional).
2. It is important that when the transmitter is switched on, the selected RF
output connection must have the suitable antenna or must be loaded.
3. The HDT-04 transmitter applies a MPEG-4 compression to either HDMI,
composite video or SDI input signals. An MPEG-1 layer 2 compression is
applied to the corresponding 4 analogue audio channels, the 2 stereo SDI
embedded, the HDMI embedded and the AES digital audio signals. The
resulting multiplexed signal is transmitted using COFDM modulation
system.
4. The HDT-04 transmitter is available in different frequency bands from 2
to 5 GHz, for the DVB-T2 and DVB-T RF stage. It can also perform ISDB-
T with interlaced (optional). The frequency band is defined on the product
P/N.
5. If the RF output is set to DVB-T2 and the bandwidth selected is 1.7 MHz,
then, the device automatically disables the Audio2 and it sets the bitrate
of the Audio1 to 128 kbps.
6. Special care should be taken with SDI cables, quality and length, these
are very important, especially when HD-SDI or 3G SDI signals are
transmitted.
7. If any audio or data channel are not used in a transmission, they should
be disabled, in order to assign that bitrate to the video and achieve a
higher quality transmitted video signal.
8. Only authorized personnel should open the product and any repair or
warranty will be invalidated if the seals are broken.

8
HDT-04 High Power Transmitter
USER’S MANUAL V9.9
First Aid in Case of Electric Shock
DO NOT TOUCH THE VICTIM WITH YOUR BARE HANDS until the circuit is
broken. SWITCH OFF. If this is not possible, PROTECT YOURSELF with DRY
insulating material and pull the victim clear of the conductor.
If breathing has stopped, indicated by unconsciousness, lack of respiratory
movements and a ‘blue’ look to cheeks, lips, ears and nails, START
RESUSCITATION AT ONCE.
EMERGENCY RESUSCITATION –THE EXPIRED AIR METHOD
(Approved by the Royal Life Saving Society)
Chapter 1: If possible, lie the victim on his back with his head slightly higher
than his feet. Clear the mouth and throat of any obvious obstruction.
Chapter 2: Kneel on one side of the victim, level with his head. LIFT THE JAW
AND TILT THE HEAD BACK AS FAR AS POSSIBLE (Figs. 1a and 1b)
Chapter 3: One of the following may happen:
a) Breathing may begin and consciousness returns.
b) Breathing may begin but consciousness NOT
returns. Turn the victim on his side and ensure
that the airway is kept clear.
c) Breathing may return but be NOISY which
means that the airway is not fully clear. Try to
clear the airway.
Chapter 4: IF THERE NO SIGN OF BREATHING:
a) Check that the head is still tilted back.
b) Take a deep breath.
c) Pinch the victim’s nose and blow firmly into his
mouth (Fig. 2). As you do, the chest will RISE.
d) Turn your head away and take another breath,
watching for the chest to FALL (Fig. 3).
Chapter 5: Start with four quick breaths and then continue
with one breath every five seconds (i.e. 12 times a minute).
This should be continued until the victim revives or a doctor
certifies death.
Chapter 6: As consciousness returns the victim will start to
breathe on his own, and a ‘pink’ color replaces the ‘blue’ look:
this is the time to stop resuscitation. Continue to hold his chin
up and so keep the airway clear.
Chapter 7: In the case of injuries to the mouth, it may be necessary to use
mouth-to-nose resuscitation. Seal the victim’s mouth with your cheek and
blow firmly into his nose, proceeding as above.

9
HDT-04 High Power Transmitter
USER’S MANUAL V9.9
Chapter 8: In the case of severe facial injuries, it may be necessary to do a
manual method of artificial respiration (Silvester-Brosch or Holger Nielsen).
Briefly, these methods apply compression to ribcage with the victim lying on
his back (S-B) or face down (H.N.) with associated movement of his arms up
and out. The cycle of movement should take about five seconds, i.e. the
normal breathing phase.
Chapter 9: Whatever the method, it is ESSENTIAL to commence resuscitation
WITHOUT DELAY and to send for medical assistance immediately.
TREATMENT FOR BURNS
If the victim is also suffering from burns, then, without hindrance to
resuscitation, observe the following:
a) DO NOT ATTEMP TO REMOVE CLOTHING ADHERING TO THE BURN.
b) If possible, alleviate the pain from the burnt part by immersing in
cold water.
c) If help as available or as soon as resuscitation is no longer required,
the wound should be covered with a DRY clean dressing.
d) Oil or grease in any form should not be applied.
e) If severely burnt, get the victim to hospital immediately.

9
HDT-04 High Power Transmitter
USER’S MANUAL V9.9
Main Index
Chapter 1: Introduction ................................................................. 12
Chapter 2: Technical Features ....................................................... 16
Chapter 3: How to Order................................................................ 20
Chapter 4: Transmitter Operation and Menus ................................ 21
4.1 Display.....................................................................................21
4.2 LEDs........................................................................................24
4.3 Keyboard .................................................................................25
4.4 Menus Scheme..........................................................................28
4.5 Menu Navigation .......................................................................33
4.6 Menu Structure .........................................................................34
Encoder Menu .....................................................................35
4.6.1.1 SDI Video Input ...................................................... 39
4.6.1.2 HDMI 1/2 Video Input ............................................ 42
4.6.1.3 CVBS Video Input ................................................... 45
4.6.1.4 ASI Video Input ...................................................... 47
4.6.1.5 Generator Video Input ............................................ 48
4.6.1.6 Audio1 Embedded ................................................... 50
4.6.1.7 Audio1 Analogue..................................................... 51
4.6.1.8 Audio1 AES-EBU...................................................... 52
4.6.1.9 Audio1 Generator ................................................... 53
4.6.1.10 Audio2 Embedded ................................................. 54
4.6.1.11 Audio2 Analogue................................................... 55
4.6.1.12 Audio2 AES-EBU.................................................... 56
4.6.1.13 Audio2 Generator.................................................. 57
4.6.1.14 Data...................................................................... 58
4.6.1.15 Encoder Output..................................................... 61
4.6.1.16 TS Parameters ...................................................... 62
4.6.1.17 Scrambler ............................................................. 65
4.6.1.18 Remux (optional).................................................. 67
RF Menu .............................................................................69
4.6.2.1 DVB-T2 ................................................................... 69
4.6.2.2 DVB-T2 Maximum Bitrates ...................................... 72
4.6.2.3 DVB-T ..................................................................... 73
4.6.2.4 DVB-T Useful Bitrate............................................... 76
Unit Menu ...........................................................................78
4.6.3.1 Profile..................................................................... 78
4.6.3.1.1 RTC-01 Remote Control Screen............................ 79
4.6.3.1.2 RTC-02 Remote Control Screen............................ 80
4.6.3.2 RTC-01 Config......................................................... 81
4.6.3.3 RTC-02 Config......................................................... 87