Swegon PARAGON Wall VAV Guide

PARAGON Wall VAV
Installation - Commissioning - Maintenance 17/01/2023
Art. 942428075
Contents
Application area.................................................. 2
General....................................................................... 2
Contents..................................................................... 2
Protective equipment .................................................. 2
Electrical safety ........................................................... 2
Handling..................................................................... 2
Installation .................................................................. 2
Cleaning ..................................................................... 2
Cleaning of electrical components ............................. 2
Service/maintenance ................................................... 2
Environment and waste disposal ................................. 2
Disposal of the product............................................... 2
Product warranty ........................................................ 2
Dimensions and weights.................................... 3
Installation .......................................................... 4
Size of the opening..................................................... 4
Suspension ................................................................. 5
Connection - Water .................................................... 7
Connecting water ....................................................... 7
Water quality .............................................................. 8
Connection - Air ......................................................... 9
Grille installation ......................................................... 9
Supply and extract air kit .......................................... 10
Connections control equipment ...................... 11
Room controller, LOCUS............................................ 13
Sensor module.......................................................... 14
Maintenance...................................................... 15
Symbols
Warning/Caution!
See also the following documents at www.swegon.com:
- PARAGON Wall VAV Product datasheet
- VAV Modbus
- Comfort modules, operation and maintenance (IOM)
- LOCUS Product datasheet
- LOCUS Instructions for Use (IOM)

PARAGON Wall VAV
2Swegon reserves the right to alter specications. 17/01/2023
Application area
The product is a comfort module designed for demand-
controlled climate indoors.
The product is used to ventilate, cool and heat premises
exactly as needed.
The product may not be used for anything other than its
intended use.
General
Read through the entire instructions for use
before you install/use the product and save the
instructions for future reference. It is not permissible to
make changes or modify this product other than those
specified in this document.
Contents
1 x PARAGON Wall VAV
1 x Instructions for use
Protective equipment
Always use appropriate personal protective
equipment for the work in question, in the form
of gloves, respirators, protective glasses and helmets during
handling, installation, cleaning and service/maintenance.
Electrical safety
Permitted voltage, see Electrical data.
It is not permissible to insert foreign objects into the product’s
contactor connections or ventilation openings; risk for
short circuiting.
24 V isolation transformer to be connected should comply
with the provisions of IEC 61558-1.
Cable sizing must be carried out for cabling between the
product and the power supply source.
Disconnect the power supply when working on products
that are not required to run.
Always follow the local/national rules for who shall be
permitted to carry out this type of electrical installation.
Handling
Always use appropriate transport and lifting devices when
the product is to be handled to reduce ergonomic loads.
The product must be handled with care.
Cleaning
Ideally the product should be cleaned twice a year by
vacuuming the coil to remove loose dust. In fibre dense
environments a more frequent interval is recommended.
A simple visual inspection of connections is recommended
when cleaning.
For cleaning grilles and other painted surfaces: Avoid
aggressive cleaning agents which may harm painted
surfaces. Normally a mild soap or alcohol solution is fully
adequate for cleaning. See also the maintenance section
in this instructions for use.
Cleaning of electrical components
• If needed, use a dry cloth to clean the components.
• Never use water, detergent and cleaning solvent or a
vacuum cleaner.
Service/maintenance
• In connection with a service, mandatory ventilation
inspection or cleaning of the ventilation system, check
that the general condition of the products looks ok.
Pay particular attention to the suspension, cables and
that they sit firmly in place.
• It is not permissible to open or repair electrical components.
• If you suspect that the product or a component is
defective, please contact Swegon.
• A defective product or component must be replaced by
an original spare part from Swegon.
Environment and waste disposal
Help to protect the environment by ensuring correct dis-
posal of the packaging and use the products in accordance
with applicable environmental regulations.
Disposal of the product
The product must not be disposed of as ordinary house-
hold refuse. They must be collected in separate containers
according to applicable local rules.
Product warranty
The product warranty or service agreement will not be in
effect/will not be extended if: (1) The product is repaired,
modified or changed, unless such repair, modification
or change has been approved by Swegon AB; or (2) the
serial number on the product has been made illegible or
is missing.
Installation
• Moist, cold and aggressive environments must be avoided.
• Assemble the product according to this instruction and
applicable industry regulations.
• Install the product for easy access during service/maintenance.
• Avoid installing the product near a heat source.
• Check to make sure that the product does not have
any visible defects.
• Check that the product is properly secured after it has
been installed.
• Secure cables with cable ties.
• Check that all cables are properly secured in place after
installation.

3
01/17/2023 Swegon reserves the right to alter specications.
PARAGON Wall VAV
Dimensions and weight
PARAGON Wall VAV 800
Length Type Dim. Dry weight* (kg) Water volume (l)
mm ØWithout
grille
incl.
grille
cooling heating
800 R A 125 17. 4 19.6 1.39
800L A 125 17. 4 19.6 1.38
800 R B 125 17. 4 19.6 1.39 0.38
800L B 125 17. 4 19.6 1.38 0.37
800 R X 125 17. 4 19.6 1.39
800L X 125 17.4 19.6 1.38
PARAGON Wall VAV 1100
Length Type Dim. Dry weight* (kg) Water volume (l)
mm ØWithout
grille
incl.
grille
cooling heating
110 0 R A125 22.6 25.5 1.93
1100L A 125 22.6 25.5 1.92
110 0 R B125 22.6 25.5 1.93 0.52
1100L B 125 22.6 25.5 1.92 0.51
110 0 R X125 22.6 25.5 1.93
1100L X 125 22.6 25.5 1.92
PARAGON Wall VAV 1400
Length Type Dim. Dry weight* (kg) Water volume (l)
mm ØWithout
grille
Incl.
grille
cooling heating
1400 R A125 27.6 31.2 2.47
1400L A 125 27.6 31.2 2.46
1400 R B125 27.6 31.2 2.47 0.65
1400L B 125 27.6 31.2 2.46 0.64
1400 R X125 27.6 31.2 2.47
1400L X 125 27.6 31.2 2.46
*Added weight for control equipment: 0.84 kg
801/1101/1401
789/1089/1389
722 (+0-20)
164
286
569 0+20
313
801/1101/1401
810/1110/1410
722 (+0-20)
164

PARAGON Wall VAV
4Swegon reserves the right to alter specications. 17/01/2023
Size of the opening
Mounting
231 (+0-20)315
92,5 92,5
26
315
231 (+0-20)
92,5
92,5
26
800/1100/1400
+ 5
-
300 +5
>20
789/1123/1423
>722
200
200
569 (+0-20)
164
153
313
286
7
17
164
153 569 (+0-20)
286
7
17
313

5
01/17/2023 Swegon reserves the right to alter specications.
PARAGON Wall VAV
Suspension
c / c = B
c / c = A M8
L (mm) A (mm) B (mm)
800 778 222
110 0 1078 222
1400 1378 222
15
23,5
8,5
12
6
222 147

PARAGON Wall VAV
6Swegon reserves the right to alter specications. 17/01/2023
4 x

7
01/17/2023 Swegon reserves the right to alter specications.
PARAGON Wall VAV
Connection - Water
Water connection on right-hand side (R).
A1 = Cooling water, supply
A2 = Cooling water, return
B1 = Heating water, supply
B2 = Heating water, return
Water connection on left-hand side. (L).
A1 = Cooling water, supply
A2 = Cooling water, return
B1 = Heating water, supply
B2 = Heating water, return
Cooling and heating R, all sizes
Cooling R, all sizes
Cooling and heating L, all sizes
Cooling L, all sizes
Water connection on the right-hand side “R” Water connection on the left-hand side “L”
Connection sizes
Standard variant with factory-fitted valves:
Length Cooling Heating
(mm) Return Return
800, 1100, 1400 DN15 male thread DN15 male thread
Standard variant without factory fitted valves:
Length Cooling Heating
(mm) Supply and return Supply and return
800, 1100, 1400 plain pipe ends plain pipe ends
(Cu) Ø 12 x 1.0 mm (Cu) Ø 12 x 1.0 mm
231 (+0-20)315
92,5 92,5
26
Note that compression ring couplings require
support sleeves inside the pipes.
A1 A2 B1
B2
A1 A2
A1 A2 B1
B2
A1 A2
15

Connecting water
Connect the water pipes using push-on couplings or com-
pression ring couplings.
Note that compression ring couplings require support
sleeves inside the pipes. Do not use solder couplings to
connect the water pipes. High temperatures can damage
the unit’s existing soldered joints.

PARAGON Wall VAV
8Swegon reserves the right to alter specications. 17/01/2023
D
B1
B2
505050
A1
A2
C
Water connection, CCO valve.
A1 = Cooling water, supply
A2 = Cooling water, return
B1 = Heating water, supply
B2 = Heating water, return
C = CCO valve
D = Flexible hose
Water quality
Swegon recommends water quality according to VDI 2035-2
for both the heating and cooling systems. In order to
maintain the oxygen content in the water below the levels
(<0.1mg/l) prescribed in VDI 2035-2, it is recommended
to install a vacuum degasser, particularly in the cooling
system where it’s more challenging to dissolved gas. It
is also important that the pre-pressure in the expansion
vessel is dimensioned according to EN-12828 for both the
heating and cooling systems and that regular checks are
made of the pre-pressure. The cooling and heating systems
must be designed to prevent oxygen from entering the
system, this is particularly important to consider when
selecting flex hose, pipes and expansion vessels.
When the system is filled with fresh water, it has an oxygen
content of approximately 8mg/l, however, this oxygen is
consumed quickly through corrosion processes and within
a few days the oxygen in the water should be consumed.
Nevertheless, it is important to avoid filling the system
with fresh water unnecessarily.
Automatic deaerators are often installed to facilitate filling
of the system. It is recommended that the automatic
deaerators are turned off once the system has been fully
vented to avoid these drawing in air in the system if the
pre-pressure in the expansion vessel should drop.
Connection of CCO valve

9
01/17/2023 Swegon reserves the right to alter specications.
PARAGON Wall VAV
All sizes have the air connection Ø125.
The air connection is centred at the rear of the product
for easy access from both ends and the rear.
Back view
Connection dimensions, air
Length (mm) Air connection (mm)
800, 1100, 1400 Ø 125
Connection - Air
Grille installation
Click!

PARAGON Wall VAV
10 Swegon reserves the right to alter specications. 17/01/2023
Supply and extract air kit
Supply air Extract air

11
01/17/2023 Swegon reserves the right to alter specications.
PARAGON Wall VAV
Inputs Outputs
Modbus Actuator
Actuator
Inputs Outputs
Modbus
Max 48 VA
Max 48 VA
Max 48 VA
Controller outputs
Connections control equipment
Wiring diagram for controller (URC1) with accessories
24V
G0G
grey
black
blue (US=black)
brown (US=white)
brown (US=white)
blue (US=black)
|1 2|3 4|5 6|7 8| 9 10 11 12 |
|13 14 15 |1617 18 |19 20 21 |
| 22 | 23 | 24 | 25 |
black
black
white
brown
white
y24V
brown
blue
black Y- control signal / styrsignal 0-10V DC
RoHS
Temperature sensor/
Window contact
Valve actuator,
cooling
Valve actuator,
heating
Key card
Condensation
sensor
CO2sensor
24V AC / DC
Cable
USB-RJ12
Cable adapter
Pressure sensor
(Modbus)
Adapter
3xRJ12
Adapter
3xRJ12
Motor
LOCUS
Room controller
VOC Sensor
Sensor module
A
B
A. Connection when a VOC sensor is used
B. Connection on slave product
LOCUS
Room controller

PARAGON Wall VAV
12 Swegon reserves the right to alter specications. 17/01/2023
RS 485type Belden 9842
Modular6/6 RJ12
Modular 6/6 RJ12
22 23 24 25
Modular
6/6 RJ12
| 12 | 3 4 | 5 6 |7 8 |9 10 11 12 |
|13 14 15 |16 17 18| 19 20 21 |
| 22 | 23 | 24 | 25 |
| 12 | 3 4 | 5 6 |7 8 |9 10 11 12 |
|13 14 15 |16 17 18| 19 20 21 |
| 22 | 23 | 24 | 25 |
MB id 8
Master
MB id 4
Master
22 23 24 25
Modular
6/6 RJ12
1 2 3 4
MB2
5678
MB1
Next Zone
CONTROL Zone
MB id 1
Super WISE
1 2 312 3
Zone
Room
| 12 | 3 4 | 5 6 |7 8 |9 10 11 12 |
|13 14 15 |16 17 18| 19 20 21 |
| 22 | 23 | 24 | 25 |
MB id 4
Master
22 23 24 25
Modular6/6 RJ12
Modular6/6 RJ12
22 23 24 25
Modular
6/6 RJ12
| 12 | 3 4 | 5 6 |7 8 |9 10 11 12 |
|13 14 15
|
16
17
18 | 19 20 21|
| 22 | 23 | 24 | 25 |
| 12 | 3 4 | 5 6 |7 8 |9 10 11 12 |
|13 14 15 |16 17 18| 19 20 21 |
| 22 | 23 | 24 | 25 |
MB id 1
Slave id 1
MB id 4
Master
22 23 24 25
Room
Room
RK 0,75
Modular
6/6 RJ12
20
19
B
A
GND
GND B A
GND B A
9
10
AGND B
AGND B
RK 0,75
GND B A

13
01/17/2023 Swegon reserves the right to alter specications.
PARAGON Wall VAV
Standards and directives
The following standards have been observed:
EC Directive: 93/68/EEC
Low Voltage Directive: 2014/35/EU
Machinery Directive: 2006/42/EEC
EMC Directive: 2014/30/EU
RoHS Directive: 2002/95/EC
Vibrations: EN-60721-3-3
Room controller, LOCUS
Main menu and explanation of symbols
Technical data
Display Capacitive touch TFT Display QVGA 2.3”
Screen resolution 320x240
Communication Modbus RTU via RS-485
Temperature sensor Internal 10K NTC sensor
Operating temperature +5 ... +40°C
Degree of protection IP20
Dimensions 88 x 88 x 35 mm
Operating voltage 12-40 VDC
Current requirement 0.5 W
Connection
LOCUS Connection Description
VDD RJ12 12-40 VDC power supply
A+ RJ12 RS-485 bus connection
B- RJ12 RS-485 bus connection
GND RJ12 Earth for 12-40 VDC power supply
Memory card slot The user panel’s software can be
updated via a Micro SD card
Display Description Explanation
Display in
standby mode
Activated with a click
Active main
menu
Increase/decrease the
setpoint temperature
by clicking on the +
or – signs
Activated boost
mode
Swipe left for
next page
Shows values from
connected sensors
Swipe right to
go back to the
main menu
A. menu
B. increase
C. swipe left to go to the next page
D. decrease
E. symbol showing ongoing cooling or heating
F. shows programmed setpoint or measured temperature
G. shows occupancy in the room
H. press to activate boost flow
AB
C
D
E
F
G
H
Description of display
If the screen is in standby mode, it is activated again by clicking.
For more detailed information about LOCUS room controller.
See documentation at www.swegon.com
• LOCUS Product datasheet
• LOCUS Instructions for Use (IOM)

PARAGON Wall VAV
14 Swegon reserves the right to alter specications. 17/01/2023
Menu sensor module:
Press and hold the left and right-hand buttons for five
seconds to access the menu.
Use the left-hand button ( ) to steps through the
menus. Use the right-hand button ( ) to confirm your
selection.
Press the left-hand but-
ton and select:
1. Alarmlist
2. Commissioning air
3. Commissioning water
6. Return to menu
Confirm selections
by pressing the
right-hand button
The alarm is shown with a number of LEDs when you
select Alarm list (1) in the menu.
Each LED represents a number as per the table above and
the numbers are added to form an alarm number.
E.g. Middle blue and the two last red are lit (xoxxoo)
Middle blue corresponds to 16, next last red 2 and last
red 1. The sum of these is 19, which is the alarm number.
Return to normal operation by pressing the right-hand
button.
1. Alarm list: See the complete alarm list to the right.
In the commissioning menus:
• Navigate between the menus by pressing the left-hand button
• Confirm selections by pressing the right-hand button
• When a selection has been confirmed, the blue LED will flash
for about 60 seconds.
• In order to return to normal operation, select "no adjustment"
2. Commissioning, air:
2.1. Min. airflow, no occupants
2.2. Min. airflow, occupancy
2.3. Max. air flow, occupancy
2.4. Min. airflow, holiday/longer period of no
occupancy
2.5. No adjustment
3. Commissioning, water:
3.1. Open the chilled water valve
3.2. Open heated water valve
3.3. No adjustment
4, 5 are not used
6. Return to menu
Alarm list for the sensor module
Alarm
no.
Type of alarm 32 16 8421
Alarm1 Supply voltage low
Alarm2 Supply voltage critical low
Alarm3 Ext temp missing
Alarm4 Ext temp error
Alarm5 Condensation sensor error
Alarm6 SM temp sensor error
Alarm7 SM button error
Alarm8 CO2sensor missing
Alarm9 VOC Error
Alarm10 Low pressure
Alarm17 SM comm error
Alarm18 Slave comm error
Alarm19 Pressure sensor comm error
Alarm20 VOC sensor comm error
Alarm21 No master request (slave)
Alarm22 Slave incompatible version
Alarm25 Heating comfort alarm
Alarm26 Cooling comfort alarm
Alarm27 Temp. Set point overlap alarm
Alarm28 Air quality comfort alarm
Alarm29 Condensation
Alarm33 24 V Out 1 overload error
Alarm34 24 V Out 2 overload error
Alarm35 24 V Out 3 overload error
Alarm41 Slave input sum alarm
Alarm42 Slave output sum alarm
ON
1 2
Presence sensor
LEDs for temperature, adjustment
or alarm indication
Function keys
LED indicating function
- Green = OK
- Flashing Green = condensation alarm
- Yellow = Alarm
- Green/Yellow = Comfort alarm (not acute)
Temperature sensor
3 parallel RJ12 ports
(Modbus) for connections
e.g. controller, additional
sensor module or PC with
the help of Cable
converterUSB-RJ12
Addressing the sensor module. 10 sensor modules
can be connected to each master unit, each one
must have a unique address to work.
Switch for termination resistance. On the last
sensor module in the circuit switch1 is set to On.
Function keys
Sensor module

15
01/17/2023 Swegon reserves the right to alter specications.
PARAGON Wall VAV
Maintenance
2
3
1
4

PARAGON Wall VAV
16 Swegon reserves the right to alter specications. 17/01/2023