Swegon WISE Adriatic Prisma User manual

WISE Adriatic d
Instructions for Use 23/03/2023
Art. 942428063
The document was originally written in Swedish
Contents
Key to symbols............................................................ 1
Application area.................................................. 2
Dimensions and weights.................................... 3
Installation .......................................................... 4
Suspended installation ................................................ 4
Surface mounted installation....................................... 5
Secure design module................................................. 6
Fold down design module........................................... 6
Water connection ....................................................... 7
Air connection ............................................................ 8
Commissioning.................................................... 9
Connection ........................................................ 10
Declaration of Conformity ............................... 13
Maintenance...................................................... 14
Fold down design module......................................... 14
Secure design module............................................... 14
Key to symbols
Symbols on the machine
This product complies with applicable
EU directives
Symbols in these Instructions for Use
Warning/Caution!

WISE Adriatic
2Swegon reserves the right to alter specications. 23/03/2023
Application area
The product is a comfort module with integrated radio
transmitter designed for demand-controlled climate indoors
within Swegon’s ventilation system WISE. The product is
used to ventilate, cool and heat premises exactly as needed.
The product may not be used for anything other than its
intended use.
General
Read through the entire instructions for use
before you install/use the product and save
the instructions for future reference. It is not
permissible to make changes or modify this
product other than those specified in this document.
Contents
1 WISE Parasol Zenith
1 x Instructions for use
Protective equipment
Always use appropriate personal protective
equipment for the work in question, in the
form of gloves, respirators, protective glasses
and helmets during handling, installation,
cleaning and service/maintenance.
Electrical safety
Permitted voltage, see Electrical data.
It is not permissible to insert foreign objects
into the product’s contactor connections or
ventilation openings; risk for short circuiting.
24 V isolation transformer to be connected should comply
with the provisions of IEC 61558-1.
Cable sizing must be carried out for cabling between the
product and the power supply source.
Disconnect the power supply when working on products
that are not required to run.
Always follow the local/national rules for who shall be
permitted to carry out this type of electrical installation.
Handling
Always use appropriate transport and lifting devices when
the product is to be handled to reduce ergonomic loads.
The product must be handled with care.
Installation
• Moist, cold and aggressive environments must be
avoided.
• Assemble the product according to this instruction and
applicable industry regulations.
• Install the product for easy access during service/
maintenance.
• Avoid installing the product near a heat source.
• Check to make sure that the product does not have
any visible defects.
• Check that the product is properly secured after it has
been installed.
• Secure cables with cable ties.
• Check that all cables are properly secured in place after
installation.

3
23/03/2023 Swegon reserves the right to alter specications.
WISE Adriatic
Dimensions and weight
WISE Adriatic Prisma
450
190
1210 / 1810 / 2410 / 3010
WISE Adriatic Ellips
513
194
1214 / 1814 / 2414 / 3014
Weight
Weight incl. controller, excl. valves, actuators and sensors.
WISE Adriatic with Prisma design section
Length Dry weight Weight, filled with water (kg)
(m) (kg) A: Cooling A/B: Cooling/
Heating
1.2 20.3 21.3 21.5
1.8 28.9 30.4 30.8
2.4 37. 2 39.3 39.8
3.0 44.9 47.5 48.2
Weight
Weight incl. controller, excl. valves, actuators and sensors.
WISE Adriatic with Ellips design section
Length Dry weight Weight, filled with water (kg)
(m) (kg) A: Cooling A/B: Cooling/
Heating
1.2 20.6 21.6 21.9
1.8 29.3 30.8 31.2
2.4 37.3 39.4 39.9
3.0 45.9 48.5 49.2

WISE Adriatic
4Swegon reserves the right to alter specications. 23/03/2023
Installation
Suspension with accessory SYST MS
Installation
The c-c dimensions are the same for WISE Adriatic with
both design module Prisma and design module Ellips. The
example shows Prisma.
ADRIATIC Suspended installation
Length c-c (mm) c-c (mm)
(m) Short side Long side
1.2 392 1173
1.8 392 1773
2.4 392 2373
3.0 392 2973
44
26
c - c 392
Y
X
M8
SYST MS
Suspended installation
suspended installation with assembly piece
SYST MS-M8.

5
23/03/2023 Swegon reserves the right to alter specications.
WISE Adriatic
Surface mounted installation
Surface-mounting the product on the ceiling using
suspension bracket SYST MD-ADRIATIC.
Installation
The c-c dimensions are the same for WISE Adriatic with
both design module Prisma and design module Ellips. The
examples below show Prisma.
Unit
Surface mounted installation
Number of
brackets
c-c (mm) Max. (mm) *
(m) pcs. X - Short side Y - Long side
1.2 2280 250
1.8 2280 250
2.4 3280 250
3.0 3280 250
* Max. distance from the end of the product.
1. Carefully measure where the bracket is to be placed so that
all the brackets are in a perfectly straight line in relation to
each other according to the c-c table. The bracket’s distance
to the edge of the short side may not exceed 250 mm, in
order for the safety cord to be able to be anchored.
2. Install the suspension bracket SYST MD-ADRIATIC in the
ceiling. Use two brackets per product for lengths 1.2 and
1.8. For lengths 2.4 and 3.0, use three brackets. Anchor the
safety cord under the suspension bracket when installing the
bracket. Use a suitable screw for the ceiling in question.
3. When all the brackets have been screwed into place with
four screws each, fold out the moving sections at either end
of the bracket to the out position.
4. Anchor the enclosed safety cord in the bracket and in the
corner of the product.
5. Then move the product straight up against the bracket.
6. Lock the product in the bracket by pressing the folded out
sections on the ends of the bracket in towards the product
on both sides.
7. Repeat this procedure for all the brackets.
c-c 120
c-c 280
c-c 23,5 c-c 23,5
X=280
Y=
<250
Y=
<250
X=280
1
2
3
4
17 18 19
20 21 22
23
24
17 18 19
20 21 22
23
24
17 18 19
20 21 22
23
24
17 18 19
20 21 22
23
24
17 18 19
20 21 22
23
24
17 18 19
20 21 22
23
24
17 18 19
20 21 22
23
24
16
15
14
13
12
11
10
9
1
2
3
4
5
6
7
8
+

WISE Adriatic
6Swegon reserves the right to alter specications. 23/03/2023
Click! Click!
Secure design module
When fastening the design module from an open position,
raise the design section until you hear a click, at which
point it is secured in the base module.
Fold down design module
The unit is equipped with a pushbutton at either end of
one of the long sides, for simple lowering of the design
section and access to e.g. control equipment. When
lowering, one long side is opened and the design section
is suspended from the opposite long side.

7
23/03/2023 Swegon reserves the right to alter specications.
WISE Adriatic
Connection dimensions
Model Length Factory-fitted Connection Coupling type Connection Coupling type
A, B, Cooling, Cooling/Heating 1.2 - 3.0 Actuator and valve Return DN15, male thread Supply pipe Plain pipe 12 x 1.0 mm
A, B, Cooling, Cooling/Heating 1.2 - 3.0 - Return Plain pipe 12 x 1.0 mm Supply pipe Plain pipe 12 x 1.0 mm
Connecting water
The water pipes are always placed on the product’s short
side, regardless of the air connection side of the product.
Connect the water pipes using push-on couplings or
compression ring couplings when the product is ordered
without valves. Note that compression ring couplings
require support sleeves inside the pipes.
Do not use solder couplings to connect the water pipes.
High temperatures can damage the unit’s existing soldered
joints.
Flexible connecting hoses for water are available for flat-
end pipes and valves, and can be ordered separately.
To avoid corrosion in the water circuit, the water quality in
the system water must be checked regularly.
Water
Connection dimensions
Unit Cooling and Heating
(m) Supply and return
1.2 1.8 2.4 3.0 plain pipe ends
(Cu) Ø 12 x 1.0 mm
Alternative to factory-fitted valves
Unit Cooling and Heating
(m) Return
1.2 1.8 2.4 3.0 DN15 male thread
Dimensions WISE Adriatic Prisma, end view, water connection
Dimensions WISE Adriatic Ellips, end view, water connection
Water connection
A1 = Supply cooling water ø12x1.0 mm (Cu)
A2 = Return cooling water ø12x1.0 mm (Cu)
B1 = Supply heating water ø12x1.0 mm (Cu)
B2 = Return heating water ø12x1.0 mm (Cu)
Kyla tillopp/
Cooling supply
Värme retur/
Heating return
Kyla retur/
Cooling return
Värme tillopp/
Heating supply
942256012
A1 A2B2 B1
67,5 35
130
35 67,5
245
99 35
35 99
245
130
Water quality
Swegon recommends water quality according to VDI 2035-2
for both the heating and cooling systems. In order to
maintain the oxygen content in the water below the levels
(<0.1mg/l) prescribed in VDI 2035-2, it is recommended
to install a vacuum degasser, particularly in the cooling
system where it’s more challenging to dissolved gas. It
is also important that the pre-pressure in the expansion
vessel is dimensioned according to EN-12828 for both the
heating and cooling systems and that regular checks are
made of the pre-pressure. The cooling and heating systems
must be designed to prevent oxygen from entering the
system, this is particularly important to consider when
selecting flex hose, pipes and expansion vessels.
When the system is filled with fresh water, it has an
oxygen content of approximately 8mg/l, however, this
oxygen is consumed quickly through corrosion processes
and within a few days the oxygen in the water should be
consumed. Nevertheless, it is important to avoid filling the
system with fresh water unnecessarily.
Automatic deaerators are often installed to facilitate filling
of the system. It is recommended that the automatic
deaerators are turned off once the system has been fully
vented to avoid these drawing in air in the system if the
pre-pressure in the expansion vessel should drop.
Water connection


WISE Adriatic
8Swegon reserves the right to alter specications. 23/03/2023
To connect the air
WISE Adriatic comes withair connection on one short
side. The sleeve is connected to the primary air duct. 
190
77
225 225
Dimensions WISE Adriatic Prisma, end view, air connection
256,5 256,5
77
194
Dimensions WISE Adriatic Ellips, end view, air connection
Connection dimensions
Unit Air connection, diameter
(m) Ø
1.2 1.8 2.4 3.0 125
Air connection

9
23/03/2023 Swegon reserves the right to alter specications.
WISE Adriatic
q = k · √p [l/s]
i
pi [Pa]
q [l/s]
k= [k-factor]
p = [Pa]
i()
k
q2
Commissioning
The water and air connection is always placed on the end
of the product.
Measuring tubes are placed on the product’s two long
sides adjoining the water and air connection.
0°
40°
-40°
+40°
-40°
0°
+40°
0°
+40°
0°
0°
Fan-shape
X-shape
ADC

WISE Adriatic
10 Swegon reserves the right to alter specications. 23/03/2023
There are different types of actuators
• For connection of the thermal actuator such as Swegon’s
actuator ACTUATORc, see figure a.
• When connecting the relay for connection of three or more
actuators, see figure b.
• When connecting of the actuator with 0-10 V control signal
(NOTE! 24 V DC supply) see figure c.
Actuator with 0-10
V control signal
0-10 V DC
Ground
24 V DC
24 V DC
Ground
Thermal actuator
ADAPT Relay
Relay for connection
of three or more
actuators
24 V DC
Ground
-
+
1
2
3A1A2
Factory fitted components as an option
• Sensor Module Advanced (WISE SMA), (Optional)
• Sensor Module Basic (WISE SMB), (Optional)
• Valves and actuators for cooling
• Valves and actuators for heating
• Temp. sensor
• Condensation sensor
Connection
WISE Parasol Zenith, connec-
tion.
LED - Explanation
Not connected “paired”
Colour Type
Energized White Permanent
Selected in TuneWISE White Flashing, fast
Prepared to be added to
the system White Flashing, slowly
To be added to the system White Flashing, fast for 5 s
Connected “paired”
Colour Type
Normal operation Green Permanent
Restart Blue Permanent for 10 s
Initiation Blue Flashing
Boosted max. flow Orange Permanent
Boosted min. flow Orange Permanent
Boosted water flow Violet Permanent
Boosted water flow/air flow Violet/Orange Alternating
Comfort alarm Red Permanent
Function alarm Red Flashing
Emergency mode Green/Red Alternating
Test mode Green/Orange Alternating
Condensation
sensor
(Optional)
WISE Adriatic with factory-fitted components
1. WISE CU (Controller Unit)
2. Motor for integrated air damper
3. Sensor for measuring supply air temperature
POWER
STATUS
+
-
11
10
98
7
6
12345
COM
POWER
6 7 8 9 10 11
1 2 3 4 5
STATUS
COM
24V AC
Temp. sensor
(Optional)
Pressure tube
Ground
0-10 V DC
Motor
WISE SMB
(Optional)
WISE SMA
(Optional)
24 V DC
Cooling Heating
LED
a b c
Valve actuator,
(Option)
1
2
3

11
23/03/2023 Swegon reserves the right to alter specications.
WISE Adriatic
Use
Use TuneWISE for commissioning. Commissioning must be
performed by qualified and trained WISE service engineers.
Use SuperWISE for settings, reading alarms, etc. refer to
the documentation for SuperWISEII / SuperWISEII SC.
Trouble shooting
The product is not shown in the system:
• Make sure that the product is energized. (e.g. diode)
• Make sure that the product is paired.
• Make sure the product is in the right network.
The product shows incorrect/no air flow/pressure
• Make sure that the product is installed according to the
recommended distance.
• Check that there is air flow/pressure.
• Check that the measuring tube is mounted correctly.
• Check that the measuring tube is undamaged.
The product does not regulate the air flow/pressure
• Check that the motor has not become detached from
the damper spindle.
• Check that the motor works by turning the motor’s
release button, turn the damper spindle, release the
knob and then see whether the motor starts to move.
The product shows incorrect/no temperature
• Make sure the temperature sensor is not missing.
• Make sure that the temperature sensor does not hang
outside the product.
• Check that the temperature sensor is connected to the
right input.
The product shows incorrect/no VOC/CO2
• Make sure the VOC/CO2 sensor (WISE SMA) is not
missing.
• Check that the VOC/CO2 sensor is connected to the
right input.
Cleaning
Ideally the product should be cleaned twice a year by
vacuuming the coil to remove loose dust. In fibre dense
environments a more frequent interval is recommended.
A simple visual inspection of connections is recommended
when cleaning.
Avoid aggressive cleaning agents which may harm
painted surfaces. Normally a mild soap or alcohol solution
is fully adequate for cleaning. See also the maintenance
section in this instructions for use.
Cleaning of electrical components
• If needed, use a dry cloth to clean the components.
• Never use water, detergent and cleaning solvent or a
vacuum cleaner.
Service/maintenance
• In connection with a service, mandatory ventilation
inspection or cleaning of the ventilation system, check
that the general condition of the products looks ok.
Pay particular attention to the suspension, cables and
that they sit firmly in place.
• It is not permissible to open or repair electrical components.
• If you suspect that the product or a component is
defective, please contact Swegon.
• A defective product or component must be replaced by
an original spare part from Swegon.
Materials and surface treatment
Sheet parts are made of galvanised sheet steel (Z275) and
pre-painted sheet SS-EN 10143+10346 - DX52D + ZA95,
NCS S 0500-N gloss 30+/-6%.
Disposal
Waste must be handled according to local regulations.
Product warranty
The product warranty or service agreement will not be in
effect/will not be extended if: (1) The product is repaired,
modified or changed, unless such repair, modification
or change has been approved by Swegon AB; or (2) the
serial number on the product has been made illegible or
is missing.

WISE Adriatic
12 Swegon reserves the right to alter specications. 23/03/2023
WISE Parasol Zenith in standard
design:
VA /
unit
Standard
VA total
WISE CU 2.3 4.3
Damper motor (315C) 2
Option: VA / unit
Valve actuator,
ACTUATORc
x 1 x 2 x 3
612 18*
WISE SMA 0.8
WISE SMB 0.6
Example:
WISE Adriatic in standard design with the following options:
Actuator for cooling and heating as well as WISE SMA, gives a total
power consumption of 4.3 + 6 + 0.8 = 11.1 VA
*Valid for products with CU ver. 2, delivered from 01/10/2019
Technical data
Max. radio frequency output: 50 mW
Frequency band: 2.45 GHz, IMS band
(2400--2483 MHz)
Temperature sensor: 0 - 50°C ± -0.5°C
Dynamic pressure sensor: 0 - 300 Pa
With WISE SMA
VOC sensor 450 - 2000 ppm
RH sensor: 0 - 100 RH%
IP class: IP20
Running time open/close (90°): 120 s
Ambient temperature
Operation: 0 – 50°C
Storage: -20 – +50°C
RH: 10 - 95%
(non condensing)
CE marking: 2006/42/EC (MD)
2014/53/EU (RED)
2011/65/EU (RoHS2)
Electrical data
Power supply: 24V AC ±15% 50 - 60Hz
Connections pipe dim.
Power: Screw terminal max. 2.5mm2
Valve actuator: Push-in spring force connections,
max. 1.5 mm2
Max. power consumption: See table below

13
23/03/2023 Swegon reserves the right to alter specications.
WISE Adriatic
Declaration of Conformity
Swegon AB hereby affirms that
WISE Parasol Zenith with integrated radio, complies with the
essential characteristic demands and relevant regulations
specified in the following directives: 2006/42/EC (MD),
2014/53/EU (RED) and 2011/65/EU (RoHS2):
The following standards have been observed:
EN ISO 12100:2010 Safety of machinery - General principles for
design - Risk assessment and risk mitigation
EN 60204-1:2006 Safety of machinery - Electrical equipment
of machines - Part 1: Generic standards
EN 60730-1:2011 Automatic electrical control and control unit
for household use - Part1: Generic standards
EN 60730-2-14:2009 Automatic electrical controls for household
and similar use - Part 2 Particular requirements
for electric actuators
IEC 60529:1992+A2:2013 Degrees of protection provided by enclosures
(IP code)
EN 61000-6-2:2007 Electromagnetic compatibility (EMC).
Generic standards. Immunity for industrial
environments
EN 61000-6-3:2007 Electromagnetic compatibility (EMC) -
Generic standards - Emission standard for
residential, commercial and light-industrial
environments
EN 300 328 V1.9.2, V1.9.1,
V1.8.1
Electromagnetic compatibility and Radio
spectrum Matters (ERM) - Wideband
Transmission systems - Data transmission
equipment operating in the 2.4 GHz ISM
band and using spread spectrum modulation
techniques
EN 60335-1:2012+A11:2014
EN 60335-2-30:2009+A11
EN 62233:2008
Electric household appliances and similar
appliances - Safety - Part 1: Generic standards
Person responsible for this declaration:
Name: Carl-Ola Danielsson, RD&I Director Room Units
Address: Fallebergsvägen, 671 34 Arvika, Sweden
Date: Arvika 23/03/2023
This declaration is applicable only if the product has been
installed according to the instructions in this document
and if no modifications or changes have been made on
this product.
References
www.swegon.com
Building Materials Declaration
WISE Adriatic product data sheet
WISE System Guide
SuperWISE II / SuperWISE II SC User Manual
WISE Project Planning Guide - Heating, Cooling & Ventilation
and Electricity & Control

WISE Adriatic
14 Swegon reserves the right to alter specications. 23/03/2023
Maintenance
Fold down design module
The unit is equipped with a pushbutton at either end of
one of the long sides, for simple lowering of the design
section and access to e.g. control equipment. When
lowering, one long side is opened and the design section
is suspended from the opposite long side.
Click! Click!
Secure design module
When fastening the design module from an open position,
raise the design section until you hear a click, at which
point it is secured in the base module.