Optional Accessory Installation
Usage
Packing List
Fig. 6 Barn door installation
1
Fig. 7 Big Honeycomb installation
32 4 5 6 7 8 9 10 11
Fig. 6～9 is the installation instruction for PL-E60D; the installation of PL-E90D is the same as PL-E60D.
Fig. 8 Barn door installation Fig. 9 Small Honeycomb installation
① ⑥ Barn door
②Big Honeycomb
③ ④ Light body
⑤ Low head screws
⑦ Small Honeycomb
⑧ Shim
⑨ ⑪ Pressure plate
⑩ Knurled thumb screws with collar
● The way to install the barndoor is shown as Fig.6 and Fig.8.
Note: Put the low head screws upward during the installation.
● Please confirm the types of honeycomb before using it. (The types of honeycomb size are shown as below).
1） Purchase of big honeycomb
Please affix the hook&loop to the frame of both the honeycomb and light body before using. Fix the honeycomb according to the arrow direction as shown in
Fig.7, and then use the light normally.
2） Purchase of small honeycomb
The small honeycomb can be used with the barndoor simultaneously. Fix
the honeycomb by rotating the pressure plate(see Fig.9 ⑪) after the
installation as shown in Fig.8, and then use the light normally.
Honeycomb type
Big honeycomb (L
X
W
X
H)
Small honeycomb(L
X
W
X
H)
PL-E60D
290mm
X
290mm
X
10mm
268mm
X
268mm
X
10mm
PL-E90D
558mm
X
290mm
X
10mm
536mm
X
268mm
X
10mm
1. Installation
1.1 Accessory installation
Pls check Optional Accessory Installation for the honeycomb (Fig.7 ②/
Fig.8 ⑦) and barn door (Fig. 6 ①) installation.
1.2 User can install the light on a tripod or stand, and adjust demanded beam
angle by knob on both sides of the U-stand.
2. Power supply
The light provides two ways of power supply, by V-mount or Gold mount
battery or by 4-pin XLR AC-DC power. Turn on the light (Fig. 3 ⑬) and set the
color temperature (Fig.3 ⑧) and brightness (Fig. 3 ⑭) to user’s requirements.
3. Dimmer and color temperature setting
The light provides two ways of adjusting the color temperature and
brightness: normal adjusting mode and quick adjusting mode. User can
switch the adjusting mode by press the dimmer knob and color temperature
adjusting knob (Fig.3⑭/⑧). User can quickly set the dimmer and color
temperature to their needs by combining two adjusting modes.
3.1 Normal adjusting mode
⑴. Color temperature adjust
Range: 2700K-6500K, adjust value: 50K
⑵. Dimmer adjust
Range: 0%-100%, adjust value: 1%
3.2 Quick adjusting mode
⑴. Color temperature adjust
Under this mode, user can quickly choose common color temperature:
2700K, 3200K, 4500K, 5600K, and 6500K
⑵. Dimmer adjust
Range: 0%-100%, adjust value: 10%
4. Communication Address Setting and Usage
Press and hold dimmer knob (Fig.3⑭) for 2s to enter communication address
setting interface, the address setting range is 001 to 512.
LCD digital tube (Fig.5 ④) flashing means the current address is selected,
rotate the brightness adjusting knob (Fig.3⑭) to set the current address, press
the brightness adjusting knob (Fig.3⑭) to confirm, when finish the last setting,
press the brightness adjusting knob (Fig.3⑭) or wait for about 5s to quit.
5. Communication Control Mode Setting and Usage
Connect the lights network through using DMX cable. Press and hold
color temperature adjusting knob (Fig.3 ⑧) for around 2 seconds to
complete the communication control setting.
5.1. DMX Communication Mode
The upper left corner of LCD shows "DMX" (Fig. 5 ①) indicating that the
communication control mode currently is the DMX communication
mode. In this mode, connect the DMX signal output device to the lights
network, and set up the communication address to work normally.
A light occupies 2 DMX control channels. The current DMX address (N) is
brightness control, and the next set address of the current value (N+1)
is color temperature control.
For example:
DMX
Communication
address
DMX
Control address
005
006
Function
Brightness 0%-100%
Color temperature 2700K-6500K
005
5.2. Interaction Control Mode
The upper left corner of LCD shows "CH" (Fig. 5 ②) indicating that the
communication control mode currently is interaction control mode. In
this mode, set the target lights to the same communication address to
work normally, and the master-slave machine is not distinguished.
Note: when using this mode, please do not connect the DMX signal output
equipment in the lighting network; otherwise the function can not be
used normally.
6. USB socket
USB socket is reserved socket. Pls use according to specified using
environment for related products, and do not use for other purpose to
avoid damage.
Packing list
PL-E60D/PL-E90D
Barn door
Ring
Safety rope
Power cable
Power adaptor
V-mount hook&loop
Tripod
Carrying case
Aluminum alloy case
Trolley case
User manual
Warranty card
DMX cable（Optional）
Honeycomb（Optional）
Barn door (Optional)
Set of Barn door and
Honeycomb(Optional)
Customers can purchase separately according to the requirements.
Package 1
X
1
/
/
/
X
1
X
1
X
1
/
X
1
/
/
X
1
X
1
Package 2
X
1
X
1
X
1
X
1
X
1
X
1
X
1
/
X
1
/
/
X
1
X
1
Package 3
X
1
X
1
X
1
X
1
X
1
X
1
X
1
/
/
/
/
X
1
X
1
Package 4
X
3
/
/
/
X
3
X
3
X
3
X
3
/
/
X
1
X
3
X
3
Package 5
X
3
X
3
/
/
X
3
X
3
X
3
X
3
/
/
X
1
X
3
X
3
Package 6
X
3
/
/
/
X
3
X
3
X
3
X
3
/
X
1
/
X
3
X
3
Package 7
X
3
X
3
/
/
X
3
X
3
X
3
X
3
/
X
1
/
X
3
X
3
Note:
1. Package 1: Single light package
2. Package 2: Single light package (with barn door)
3. Package 3: Single light engineering package (with barn door)
4. package 4: KIT1 (with trolley case)
5. Package 5: KIT2 (with trolley case, barn door)
6. Package 6: KIT3 (with aluminum alloy case)
7. Package 7: KIT4 (with aluminum alloy case, barn door)
