Switched on Products UK113 Assembly instructions

Light Switch Timer
Installation & Programming Manual
Please read before using this timer.

Thanks for Purchasing the New Light Switch Timer – Please read the instructions to learn how to
install and use your new timer correctly.
Whilst you will not be accessing or touching any wiring before attempting any installation turn off the
electricity supply at the mains switch, fuse box or consumer unit during installation of the cradle.
If in doubt consult a qualified electrician
The Unit only works on standard type light switches. It CAN NOT be used on Flat panel switches,
Flush mount switches or dimmer switches.
Please Note
•This unit operates using two fresh, high-quality AA alkaline batteries (not included)
•Batteries must be installed for unit to operate.
•USE OF NICKEL CADMIUM OR OTHER RECHARGEABLE BATTERIES VOIDS WARRANTY.
•Use of unit in extremely cold temperatures or damp conditions will cause batteries to fail and may
void warranty.
Package Contents
1 Light switch timer unit
1 cradle
2 control Wheels
1 “n” shaped plastic insert (only required if the control wheels do not to operate your light switch after
installation)

Features
Your ‘Light Switch Timer’ allows you to turn your lights on and off according to the programmed settings.
This instruction manual will provide guidance on how to install & programme the timer. Installation requires
no wiring, and the timer will work on single, double or triple gang switches.
Perfect for:
•If you’re out late at night or away on holiday
•Ensuring you don’t come home to a dark house in the dark winter months.
Your Light switch timer includes;
•7 day digital timer, 9 programmes per day, Daily, Weekly, or Multiple-Day Programme Selections
•3 Modes - Random, Pre-programmed and Manual
•Large easy to read LCD screen clearly shows all Programming information, the current time, day of
the week and the room temperature.
•Glowing buttons for night time operation
•Flexible programming from as little as 1 minute to 23 hours and 59 minutes on each programme.
•Low battery indicator

Installation
Installing the cradle
Installing the batteries
Control Layout
Programming the Timer
Setting the Time and day
Installing Control Wheels
Selecting the correct wheels
Programming the Timer
Quick Start
Random Night Timer Feature Prog 0
Review Programming
Clear Programming
Daily Operation
Setting the mode of operation
Removing and storing the timer
Removing the cradle
Trouble shooting / FAQ
Re-setting the timer
Error Message
Usage
Programming: Examples
Notes
Warranty
Contact Info

Quick Start Guide - Installing & setting up your Light switch timer
STEP 1 - Installing the Cradle
•Turn off the power to the lights at the mains
•Using a screw driver, loosen both screws on the switch plate - Eight to Ten full turns of the screw is
enough for you to install the cradle. Do not to fully remove the screw
•Slide the cradle behind the light switch – Between the wall and the switch as shown
•Re-tighten the screws – Do not over tighten the screws
•Turn the mains power back on.
NB When installing on 3 gang switches ensure the cradle is centred relative to the switches.
STEP 2 – Inserting the batteries
•Insert two (2) high quality AA batteries into the battery compartment in the rear of the unit per the
polarity symbols (+ and -) indicated.
•The LCD will flash AM 12:00, Mon (Monday), and OFF.

Control Layout
1
2
3
4
5
The screen displays:
1. Day of the week
2. AM and PM hrs/min
3. Timer mode (auto or manual)
4. Low Battery indicator
5. Temperature Display
6. Reset Hole
DAY: Press to set current day and programme day(s) of week
HOUR: Press to set hour of current time and for programme operation
MIN: Press to set minute(s) of current time and for programme operation
ENTER: Press to begin day/time setup and confirm the setups or press to select programme numbers.
PROG: Press to begin Programming and confirm the programmes.
ON: Manually turns switch to ON position or turn on the programme 0
OFF: Manually turns switch to OFF position or turn off the programme 0

STEP 3 – Setting Time & Day
Press ENTER to start the day/time setup – The temp display will disappear and the colon will stop flashing
1. Press DAY button until the current day of the week appears at the top of the display
2. Press HOUR button until the current hour of the day appears on the display
Make sure you are setting the AM/PM correctly
3. Press MIN on timer keypad to enter the correct time
4. Press ENTER to Complete setting the time. Two dots will flash indicating the unit is running.
Selecting the Temperature display units
Pressing and holding the MIN button for 5 seconds will toggle the temperature between Centigrade &
Fahrenheit

STEP 4 – Installing Control Wheels
The Light switch timer operates your lights by rolling the control wheel over the switch to move it from the on
position to the off position & vice versa.
4
3
2
1
1. Control wheels
2. Control wheel Slots
3. Switch gang indicators
4. Control wheel storage Hole
With the back sliding panel in the upper position as shown (Pressing the off button will lift the sliding plate to
the upper position)
Insert the control wheels in the desired position as per the switch gang indicator numbers at the rear of the
unit.
•For a single gang switch, place the control wheel in the central slot (marked 1) as shown
•For a two gang switch you would use one or both the slots Marked with a 2
•For triple gang switches use slots marked with a three and or the central slot.
The wheels will click into place - Ensure the wheel fully clicks into place on both sides.
To Remove Wheels
Wheels should be removed by placing your finger behind the wheel with the slider in the upper
position and pushing it outwards from behind the wheel.
NOTE : The unit can be used to operate one or two switches at a time.
On double or triple gang switches the location of the wheels will be on the mirror side as the unit will be
reversed when installed in the cradle.

STEP 5 – Insert the unit into the cradle
Slide the unit into the cradle.
Test by pressing the on / off button to ensure the unit correctly operates your light switch.
If the unit fails to operate the lights check you have placed the control wheels in the operate control slot for
the switch.
Please consult the Trouble shooting guide if the unit still fails to operate your lights.
STEP 6 – Programming the Timer
NOTE: It is easier to programme the unit before installation in the cradle,
Before using your timer, please ensure you have correctly set the current day and time (including
am/pm indicator).
The timer offers 7-days timer with 9 ON/OFF programmes (Programme 1 to 9) and a special random night
timer (Programme 0).
Once set, the timer will operate each week until reset or batteries expire.
The timer has the following, convenient different day modes for easy Programming:
1. Every day;
2. Week days from Monday to Thursday;
3. Week days from Monday to Friday;
4. Weekend from Saturday to Sunday
5. The whole week from Monday to Sunday.
6. -:- - (No day)

Quick Start
Follow these steps to set one programme that will switch the light automatically for each of the seven (7)
days of the week.
1. Press PROG button, PROG will start blinking 1 ON -:- - on the LCD, (The days and times you enter will
remain as Programme No. 1 until you over-ridethe programme or the unit is reset. Additional
programmes will automatically be numbered as entered.)
2. Press the DAY button repeatedly until all MON TUE WED THU FRI SAT SUN are displayed at the top of
the LCD.
3. Press HOUR repeatedly to set the correct AM or PM hour for ON. Press MIN repeatedly to set the
minutes of the hour. Your timer is now set to turn the switch ON at this same time every day, 7 days a
week.
4. Press ENTER. The LCD will flash PROG 1 OFF.
5. Press the DAY button repeatedly until all MON TUE WED THU FRI SAT SUN are displayed at the top of
the LCD.
6. Press HOUR repeatedly to set the correct AM or PM hour for OFF. Press MIN repeatedly to set the
minutes of the hour. Your timer is now set to turn the switch OFF at this same time every day, 7 days a
week.
7. To set multiple programmes, press ENTER to continue to the next programme setting.
8. When finished Programming, press PROG to return LCD to current day and time. Once you programme
the timer, AUTO will be displayed on the LCD.
Note:
Press ENTER to cycle through the different programme numbers, 1- 9 ON and 1 - 9 OFF. The last PROG 0
is a special programme, please refer to the “Set for Programme 0” section for details.
After you have finished Programming, press PROG to save your settings to the timer, if the PROG button is
not pressed, after 30seconds the timer will go back to the original programme set up.
Once Programming is completed, the LCD will again display the current day, time and temperature display.
Insert the unit into the. cradle
It is easier to slot the unit into the cradle when both the switch and the unit are in an off position.