Synology SA3600 Manual

Synology NAS SA3600
Hardware Installation Guide

Table of Contents
Chapter 1: Before You Start
Package Contents 3
Synology SA3600 at a Glance 4
Hardware Specication 5
Optional Accessories 6
Safety Instructions 8
Chapter 2: Hardware Setup
Tools and Parts for Component Installation 9
Install Drives 9
Install Memory Modules 11
Install PCle Add-in Cards 13
Install and Remove Rail Kits 15
Expansion Unit Deployment and Topology 18
Start up Your Synology NAS 19
LED Indicator Table 20
Chapter 3: System Maintenance
Replace System Fan 21
Replace Power Supply Unit (PSU) 23
Initial Troubleshooting Guide 23
Chapter 4: Install DSM on Synology NAS
Install DSM with Web Assistant 24
Learn More 24
Synology_HIG_SA3600_20190808
2

Synology NAS SA3600 is an enterprise server consisting of both system hardware and the software operating
system, DiskStation Manager (DSM). This manual will guide you through all conguration aspects of your
SA3600, including the hardware components, setup procedures, system maintenance, and initial troubleshooting
instructions.
Note: All images below are for illustrative purposes only, and may differ from the actual product.
Package Contents
Main unit x 1 AC power cord x 2
Screws for 2.5” drives x 52
Screws for 3.5” drives x 52
Before You Start 1
Chapter
3
3

4Chapter 1: Before You Start
Synology SA3600 at a Glance
No. Article Name Location Description
1 Power Button and Indicator
Front
1. Press to power on your Synology NAS.
2. To power off the Synology NAS, press and hold until you hear a beep
sound and the Power LED starts blinking.
2 Status Indicator Displays the status of the system. For more information, see "LED Indicator
Table."
3 Alert Indicator Displays warnings regarding fan or temperature. For more information, see
"LED Indicator Table."
4 Beep Off Button Press to deactivate the beeping sound that is emitted when a malfunction
occurs.
5 Drive Status Indicator Displays the status of drives. For more information, see "LED Indicator Table."
6 Drive Tray Install drives (hard disk drives or solid state drives) here.
7 Rail Kit Release Tab Push in and hold to release the Synology NAS from the rail kit lock.1
8 Power Port
Back
Connect power cords here.
9 PSU Indicator and Beep Off
Button
1. Displays the status of the power supply unit (PSU). For more information,
see "LED Indicator Table."
2. Press to deactivate the beeping sound that is emitted when a malfunction
occurs.
10 PSU Fan Disposes of excess heat and cools the PSU.
11 Console Port This port is used for manufacturing use only.
12 PCI Express Expansion Slot Supports additional PCIe network interface cards.
13 SAS OUT Port Connect to Synology Expansion Unit2here.
14 1GbE LAN Port Connect RJ-45 network cables here.
15 10GBase-T LAN Port Connect RJ-45 network cables here.
16 USB 3.0 Port Connect external drives, USB printers, or other USB devices to the Synology
NAS here.
17 Reset Button
1. Press and hold until you hear a beep sound to restore the default IP
address, DNS server, and password for the admin account.
2. Press and hold until you hear a beep sound, then press and hold again until
you hear three beep sounds to return the Synology NAS to “Not Installed”
status so that DiskStation Manager (DSM) can be reinstalled.
1For more information about the rail kit installation, please refer to the Quick Installation Guide that comes with the rail kit.
2For more information about Synology Expansion Unit supported by your Synology NAS, please visit www.synology.com.

5Chapter 1: Before You Start
Hardware Specication
Item SA3600
Compatible Drive Type 3.5”/2.5” SAS/SATA x 12
Maximum Raw Capacity • 192 TB (12 x 16TB HDD)
• 1536 TB with 7 x RX1217sas (expansion unit)
External Device Port • USB 3.0 x 2
• SAS OUT x 1
LAN Port • 1GbE (RJ-45) x 4
• 10GBase-T (RJ-45) x 2
PCIe Slot Gen3 x8 slots (x8 link) x 2
Size (H x W x D) (mm) • 88 x 482 x 724 (with server ears)
• 88 x 430.5 x 692
Weight (kg) 14.5
Supported Client • Windows 7 and 10
• Mac OS X 10.11 onward
File System • Internal: Btrfs, ext4
• External: Btrfs, ext4, ext3, FAT, NTFS, HFS+, exFAT1
Supported RAID Type • Basic • JBOD • RAID 0 • RAID 1
• RAID 5 • RAID 6 • RAID 10 • Synology RAID F1
Agency Certication • FCC Class A • CE Class A • BSMI Class A
• EAC • VCCI • CCC • RCM • RoHS Compliant
HDD Hibernation Yes
Scheduled Power On/Off Yes
Wake on LAN Yes
Language Localization
Environment Requirement
• Line voltage: 100V to 240V AC
• Frequency: 50/60Hz
• Operating Temperature: 32 to 95˚F (0 to 35˚C)
• Storage Temperature: -5 to 140˚F (-20 to 60˚C)
• Relative Humidity: 5% to 95% RH
Note: Model specications are subject to change without notice. Please refer to www.synology.com for the latest information.
1Support for exFAT can be enabled by purchasing and downloading exFAT Access in Package Center.

6Chapter 1: Before You Start
Optional Accessories
With Synology accessories, you can customize your Synology NAS to t different business environments without
worrying about compatibility and stability. Visit www.synology.com/compatibility for more information.
• Memory Module
Model Name Picture Description
D4RD-2666-16G 16GB DDR4-2666 ECC registered
DIMM
D4RD-2666-32G 32GB DDR4-2666 ECC registered
DIMM
Note: It is required to use D4RD-2666-16G with identical memory modules of the same capacity and frequency.
• PCIe Add-in Card
Model Name Picture Description
E10G18-T2 Dual-port, 10GbE RJ-45 network
interface card
E10G18-T1 Single-port, 10GbE RJ-45 network
interface card
E10G17-F2 Dual-port, 10GbE SFP+ network
interface card
• Expansion Unit
Model Name Picture Description
RX1217sas
12-bay rackmount type expansion
unit, compatible with 3.5”/2.5” SAS/
SATA drives
RX2417sas
24-bay rackmount type expansion
unit, compatible with 2.5” SAS/
SATA drives
Note: Your Synology NAS supports up to seven expansion units.

7Chapter 1: Before You Start
• Rail Kit
Model Name Picture Description
RKS1317 Sliding rail solutions
• Spare Part
Model Name Picture Description
Disk Tray (Type R7) 3.5"/2.5" drive tray
FAN 80*80*32_6 System fan module
PSU 500W-RP
Module_2 Redundant PSU module
PSU 500W-RP
SET_2
Redundant PSU set (cage x 1,
PSU module x 2)

8Chapter 1: Before You Start
Safety Instructions
Keep away from direct sunlight and away from chemicals. Make sure the environment does not
experience abrupt changes in temperature or humidity.
Place the product right side up at all times.
Do not place near any liquids.
Before cleaning, unplug the power cord. Wipe with damp paper towels. Do not use chemical or
aerosol cleaners.
To prevent the unit from falling over, do not place on carts or any unstable surfaces.
The power cord must plug in to the correct supply voltage. Make sure that the supplied AC voltage is
correct and stable.
To remove all electrical current from the device, ensure that all power cords are disconnected from
the power source.
Risk of explosion if battery is replaced with an incorrect type. Dispose of used batteries appropriately.

9
Tools and Parts for Component Installation
Please prepare below tools and parts before setting up your Synology NAS:
• A screwdriver
• At least one 3.5” or 2.5” SAS/SATA drive (please visit www.synology.com/compatibility for compatible drive
models)
Warning: If you install a drive that contains data, the system will format the drive and erase all existing data. Please
back up any important data before installation.
• Rail mounting kit (please see the Optional Accessories section to nd out the suitable rail kit for cabinet
installation)
Warning: We suggest mounting your Synology NAS on a cabinet before installing any drives since the heavy weight
will increase the installation difculty.
Install Drives
Please follow below steps for drive installation:
1 Open the drive tray.
a Find the small button located on the left side of the drive tray handle. Press the button down, and the drive
tray handle will pop out.
b Pull the drive tray handle out as illustrated above.
2 Install drives:
• For 3.5” drives: Place the drive in the drive tray. Turn the tray upside down and tighten screws into the four
spots indicated below to secure the drive.
• For 2.5” drives: Place the drive in the drive tray. Turn the tray upside down and tighten screws into the four
spots indicated below to secure the drive.
Hardware Setup 2
Chapter

10 Chapter 2: Hardware Setup
3 Insert the loaded drive tray into the empty drive bay.
Note: Make sure the tray is pushed in all the way. Otherwise, the drive might not be able to function properly.
4 Push the handle inward to secure the drive tray.
5 Push the switch on the drive tray handle to the left to lock the drive tray.
6 Repeat the steps above to assemble the other drives you have prepared.
7 Drives are numbered as shown below.
Note: We suggest installing drives of the same size to optimize drive capacity usage when creating RAID volumes.

11 Chapter 2: Hardware Setup
Install Memory Modules
You must install genuine Synology memory module(s) to ensure system compatibility and reliability. Be sure to
follow the congurations below for the suggested installation sequence of different memory capacities, otherwise
the system may not boot successfully, or system performance and stability may suffer.
A0 A1 B0 B1 Total Memory
16GB - - - 16GB
32GB - - - 32GB
16GB - 16GB - 32GB
16GB 16GB 16GB - 48GB
16GB 16GB 16GB 16GB 64GB
32GB - 32GB - 64GB
32GB 32GB 32GB - 96GB
32GB 32GB 32GB 32GB 128GB
Note: It is required to use identical memory modules of the same capacity and frequency.
Follow the steps below to install, check, or remove a memory module on your SA3600.
To install the RAM module:
1 Shut down your SA3600. Disconnect all cables connected to your SA3600 to prevent any possible damage.
2 Remove the screw on the back of SA3600. Pull the rear top cover, and put it aside.
Note: When you remove the rear top cover, sensitive internal components are exposed. Avoid touching anything
other than the memory assembly when you remove or add memory.

12 Chapter 2: Hardware Setup
3 Insert the new memory module in the slot:
a Push the retaining clips on the slot out to the sides.
b Align the notch on the gold edge of the module with the notch in the memory slot.
c Push down on the memory module with rm and even pressure. The retaining clips will snap into position as
the module is correctly inserted.
Note: Hold the memory module by its edges, and do not touch the gold connectors.
4 Put back the rear top cover you lifted in step 2.
a Align the hexagons at the side of rear top cover with the slots on the chassis’ edge, and push the rear top
cover back in position.
b Put back and fasten the screw you removed in step 2.

13 Chapter 2: Hardware Setup
To make sure SA3600 recognizes the new memory capacity:
1 Log in to DSM as admin or a user belonging to the administrators group.
2 Check Total Physical Memory in Control Panel > Info Center.
To remove the RAM Module:
1 Follow step 1 and 2 of the To install the RAM module section to shut down your SA3600, disconnect the
cables, and then remove the rear top cover.
2 Cut the cable tie before removing the memory module. (The pre-installed memory module is cable tied to
prevent loosening during delivery.)
Note: Avoid touching any components of the motherboard when you cut the cable tie.
3 Disengage the memory retaining clips by pushing them outward, and the module will pop out of the slot.
4 Follow step 4 of the To install the RAM module section to put back the top cover.
Install PCle Add-in Cards
SA3600 provides two PCIe slots for optional add-in card expansion, allowing network interface cards to be
installed.
To install the network interface cards:
1 Shut down your SA3600. Disconnect all cables connected to your SA3600 to prevent any possible damages.
2 Open the SA3600 by following step 2 of the To install the RAM module section.
3 Install the network interface card.
a Remove the screw that secures the expansion slot’s cover.
b Lift the expansion slot’s cover.

14 Chapter 2: Hardware Setup
c Align the card’s connector with the expansion slot, and insert the card into the slot.
Note: Make sure the connector is fully inserted. Otherwise, the network interface card might not be able to function
properly.
d Put back and fasten the screw that you removed in step 3-a so as to secure the newly inserted card.
4 Repeat step 3 to install the other network interface card for your SA3600.
5 Put back the rear top cover by following step 4 of the To install the RAM module section.

15 Chapter 2: Hardware Setup
Install and Remove Rail Kits
Here we use RKS1317 as an example to illustrate how to install or remove the rail kits. For more information
about the rail kit installation, please refer to the Quick Installation Guide that comes with the rail kit.
To install the rail kit:
1 To install the rail kit to the rack
a Attach the rear end of the rail kit assembly to the rack.
b Slide the front latch outward and insert the brackets into the rack holes.
2 Extend and pull out the inner rail from the assembly.

16 Chapter 2: Hardware Setup
3 Align the xing holes of the inner rail to the side of the chassis and slide backward to attach the inner rail.
4 With the help of another person, carefully align the inner rail to the outer rail assembly.
5 Pull and hold the front latch of the inner rail to unlock the inner rail, and push the chassis towards the rack. Use
the cage nuts and screws in the rail kit package to secure the chassis to the rack if necessary.

17 Chapter 2: Hardware Setup
To remove the rail kit:
1 To remove the chassis from the rack, hold the rail kit release tabs on the ear holders and pull out the chassis
from the rack.
2 With the help of another person, carefully remove the chassis from the rack. Then, slide forward to remove the
inner rail from the chassis.

18 Chapter 2: Hardware Setup
Expansion Unit Deployment and Topology
SA3600 supports RX1217sas (12-bay) and RX2417sas (24-bay) expansion units, providing seamless storage
expansion whenever needed. This section will guide you through how to connect the expansion units to your
Synology NAS.
To connect RX1217sas/RX2417sas with SA3600:
1 Connect one end of the expansion cable to the SAS OUT port of your SA3600 and the other to the SAS IN port
of RX1217sas/RX2417sas. Make sure the release band (in blue) of the cable faces rightward when plugging
into the SA3600, and that of the cable faces upward when plugging into RX1217sas/RX2417sas; otherwise,
the SA3600 and expansion unit will not be correctly connected.
2 Connect one end of the power cord(s) to the power port of RX1217sas/RX2417sas, and the other to the power
outlet(s). RX1217sas/RX2417sas will automatically power on once the power cords are correctly connected.
Note:
• Your RX1217sas/RX2417sas comes equipped with a redundant power supply system, allowing two power
cords to be connected. The system may be powered on with only one power cord, but we recommend using
two power cords to avoid unexpected power failures.
• Your Synology NAS supports up to seven expansion units.
Important: Do not remove the expansion cable while the host device is still powered on. Doing so may result in data
loss.

19 Chapter 2: Hardware Setup
3 Press the power button on the front panel to power on your SA3600. The expansion unit ID of RX1217sas/
RX2417sas connected to SA3600 will be displayed in sequence on the back panel.
Note: Even with the Synology NAS and expansion unit(s) powered on, you can still expand with one or more
expansion unit if needed. To do so, repeat above steps to connect the expansion cables and power cords of the other
expansion units. Your expansion units will automatically power on if they are correctly connected, and the expansion
unit ID will be displayed accordingly after a few seconds (if DSM is correctly installed in the Synology NAS server).
Start up Your Synology NAS
To start up your SA3600:
1 Connect one end of each power cord to the power ports located on the back of the SA3600 and the other end
to a power outlet.
2 Connect at least one LAN cable to one of the LAN ports and the other end to your switch, router, or hub.
3 Press the power button to turn on the SA3600.
Congratulations! Your Synology NAS is now online and detectable from a network computer.

20 Chapter 2: Hardware Setup
LED Indicator Table
LED Indicator Color Status Description
Power
Blue
Static Powered on
Blinking Booting up / Shutting down
Off Powered off
STATUS
Green Static Volume normal
Orange Blinking
Volume degraded / Volume crashed
Volume not created
DSM not installed
Off HDD hibernation
ALERT
Orange Blinking Fan failure / Over temperature
Off System normal
Drive Status Indicator
(on tray)
Green
Static Drive ready and idle
Blinking Accessing drive
Red Static Drive error / Port disabled1
Off No internal drive
PSU Indicator
Green Static Power supply unit normal
Off Power supply unit off
Rear 1GbE LAN
(on left side of jack)
Green
Static Network connected
Blinking Network active
Off No network
Rear 1GbE LAN
(on right side of jack)
Green
Static
1 Gbps connected
Orange 100 Mbps connected
Off 10 Mbps connected / No network
Rear 10GbE LAN
(on left side of jack)
Green
Static Network connected
Blinking Network active
Off No network
Rear 10GbE LAN
(on right side of jack)
Green
Static
10 Gbps connected
Orange 1 Gbps connected
Off No network
Note: Model specications are subject to change without notice. Please refer to www.synology.com for the latest information.
1Please try to restart your Synology NAS or re-insert the drive(s), and then run the HDD/SSD manufacturer's diagnostic tool to check the health status of the
drive(s). If you can log into DSM, please run the built-in S.M.A.R.T. test to scan the drive(s). If the problem remains unresolved, please contact Synology
Technical Support for help.