Synthes UNIUM User manual

UNIUM™
POWER TOOL FOR SMALL BONE TRAUMATOLOGY,
ORTHOPEDIC SURGERY AND STERNOTOMIES
Instructions for Use

Introduction UNIUM™ Portfolio Overview 4
General Information 8
UNIUM™ Handpieces Modular Handpiece 11
Reciprocating Saw Handpiece 12
UNIUM™ Power Unit UNIUM™ Power Unit 13
Charging, Storage and Use 14
Aseptic Transfer Technique 15
Attachments for UNIUM™ Modular Handpiece Introduction 17
Drill Attachments 18
Ream Attachments 19
Screw Attachment and Quick Coupling
for Kirschner Wires 20
Burr Attachment 21
Saw Attachments 22
Radiolucent Drive 25
Care and Maintenance General Information 27
Cleaning and Disinfection 29
• Preparation Prior to Reprocessing 29
• Manual Cleaning Instructions 30
• Automated Cleaning Instructions with
Manual Pre-Cleaning 33
Maintenance and Lubrication 37
Inspection and Function Test 40
Packaging, Sterilization and Storage 41
Repairs and Technical Service 42
Disposal of Waste and Materials 43
2Instruction for Use • UNIUM™
Table of Contents

Specications Duty Cycles 44
Applicable Standards, Environmental Conditions and
Transportation 45
Emission Sound Pressure, Sound Power, Vibration 46
Electromagnetic Compatibility 48
Explanation of Symbols Used Symbols for Operating the Device 51
General Symbols 52
Troubleshooting 53
Ordering Information 54
Glossary
The following abbreviations are used in the UNIUM™ Instructions for Use:
Abbreviation Description
WWatt
rpm Revolutions per minute
Nm Newtonmeter
osc./min Oscillations per minute
gGram
kg Kilogram
lbs Pound
mm Millimeter
mMeter
L W  HLength Width Height
sec Second
min Minute
hHour
°C Degrees Celsius
°F Degrees Fahrenheit
hPa Hectopascal
VVolt
Ah Ampere hour
Wh Watt hour
3UNIUM™•Instruction for Use
■Notes
▲Precautions
▲WARNINGS

UNIUM™ Modular Handpiece (05.001.601)*
Speed (without attachment): 0–3,400rpm
Torque (with reaming attachment): 0–6.0 Nm
Weight: 750 g/1.65 lbs (incl. Power Unit)
Size: 117 × 64 × 181 mm (L × W × H)
Cannulation: B3.2 mm
Protection against electric shock: BF IEC 60601-1
Protection against water ingress: IPX6 / IPX8 / IPX9
The handpiece is compatible with a full range of attachments
and Small Bone Cutting Tools.
Introduction
UNIUM™ Portfolio Overview
Attachments for UNIUM™ Modular Handpiece
To be used for drilling, reaming, screwing, wire setting,
burring and sawing.
Cutting Tools
Detailed ordering information on the cutting tools can be
found in the brochure “Small Bone Cutting Tools”.
* Technical data is subject to tolerances.
4Instruction for Use • UNIUM™

UNIUM™ Reciprocating Saw Handpiece
(05.001.611)*
Speed: 0–12,400 osc./min
Size: 178 × 64 × 186 mm (L × W × H)
Stroke: 4 mm
Weight: 915 g/2.02 lbs (incl. Power Unit)
Protection against electric shock: BF IEC 60601-1
Protection against water ingress: IPX6 / IPX8 / IPX9
Size and weight gures do not include the Top for Sternum and Reciprocating
Saw Blade.
* Technical data is subject to tolerances.
** Supplied exclusively in sterile packaging. The saw blade is single use only.
*** Supplied in either sterile or non-sterile packaging. The saw blade is reusable.
UNIUM™ Top for Sternum for Reciprocating
Saw Handpiece (05.001.612)
Size: 91 × 35 × 29 mm (L × W × H)
Weight: 40 g/0.09 lbs
The Top for Sternum is compatible with the UNIUM
Reciprocating Saw Handpiece and the following saw
blades:
Reciprocating Saw Blades
511.910S** Reciprocating Saw Blade
41.5 × 10 × 0.80 mm
511.915S*** Reciprocating Saw Blade
41.5 × 10 × 1.10 mm
All other Reciprocating Saw Blades are compatible with
the UNIUM Reciprocating Saw Handpiece (05.001.611),
but can not be used with the Top for Sternum
(05.001.612). A list of these saw blades can be found in
the brochure “Small Bone Cutting Tools”.
This image shows the Top for Sternum (05.001.612) and Reciprocating
Saw Blade (511.910S) connected to the Reciprocating Saw Handpiece.
Both articles are sold separately.
Introduction
UNIUM Portfolio Overview
5UNIUM™• Instruction for Use