Synway SMG Series User manual

Synway SMG Series Digital Gateway
SMG2030
SMG2060
SMG2120
SMG3008
SMG3016
Digital Gateway
Version 1.6.0
Synway Information Engineering Co., Ltd
www.synway.net
All manuals and user guides at all-guides.com
all-guides.com

Synway Information Engineering Co., Ltd
SMG Series Digital Gateway User Manual (Version 1.6.0) Page i
Content
Content ..................................................................................................i
Copyright Declaration...........................................................................iv
Revision History.....................................................................................v
Chapter 1 Product Introduction........................................................1
1.1 Typical Application......................................................................................... 1
1.2 Feature List.................................................................................................... 2
1.3 Hardware Description.................................................................................... 3
1.4 Alarm Info ...................................................................................................... 5
Chapter 2 Quick Guide ......................................................................6
Chapter 3 WEB Configuration.........................................................12
3.1 System Login............................................................................................... 12
3.2 Operation Info.............................................................................................. 13
3.2.1 System Info.............................................................................................................13
3.2.2 PSTN Status...........................................................................................................15
3.2.3 SS7 Server .............................................................................................................18
3.2.4 Call Count...............................................................................................................22
3.3 VoIP Settings............................................................................................... 23
3.3.1 SIP Settings............................................................................................................24
3.3.2 SIP Trunk................................................................................................................26
3.3.3 SIP Register............................................................................................................27
3.3.4 SIPAccount............................................................................................................30
3.3.5 SIP Trunk Group .....................................................................................................32
3.3.6 Media Settings........................................................................................................35
3.4 PCM Settings............................................................................................... 37
3.4.1 PSTN......................................................................................................................38
3.4.2 Circuit Maintenance................................................................................................39
3.4.3 PCM........................................................................................................................39
3.4.4 PCM Trunk..............................................................................................................41
3.4.5 PCM Trunk Group...................................................................................................44
3.4.6 Number-receiving Rule...........................................................................................46
3.4.7 Reception Timeout..................................................................................................48
3.4.8 Number Attribution..................................................................................................50
3.5 SS7 Settings................................................................................................ 50
3.5.1 SS7.........................................................................................................................51
3.5.2 TUP ........................................................................................................................52
3.5.3 TUP Number Parameter.........................................................................................53
3.5.4 ISUP.......................................................................................................................55
3.5.5 ISUP Number Parameter........................................................................................57
3.5.6 Original CalleeID Pool ............................................................................................60
3.5.7 Redirecting Number Pool........................................................................................61
3.5.8 SS7 Server .............................................................................................................63
All manuals and user guides at all-guides.com

Synway Information Engineering Co., Ltd
SMG Series Digital Gateway User Manual (Version 1.6.0) Page ii
3.6 ISDN Settings.............................................................................................. 69
3.6.1 ISDN.......................................................................................................................70
3.6.2 Number Parameter.................................................................................................72
3.6.3 Redirecting Number................................................................................................73
3.6.4 Add Gateway..........................................................................................................73
3.7 SS1 Settings................................................................................................ 75
3.8 Fax Settings................................................................................................. 76
3.8.1 Fax..........................................................................................................................77
3.9 Route Settings............................................................................................. 78
3.9.1 Routing Parameters................................................................................................79
3.9.2 IP to PSTN..............................................................................................................79
3.9.3 PSTN to IP..............................................................................................................81
3.10 Number Filter............................................................................................... 82
3.10.1 Whitelist..................................................................................................................83
3.10.2 Blacklist ..................................................................................................................85
3.10.3 Number Pool...........................................................................................................86
3.10.4 Filtering Rule...........................................................................................................87
3.11 Number Manipulation................................................................................... 90
3.11.1 IP to PSTN CallerID................................................................................................90
3.11.2 IP to PSTN CalleeID...............................................................................................93
3.11.3 IP to PSTN Original CalleeID..................................................................................94
3.11.4 PSTN to IP CallerID................................................................................................94
3.11.5 PSTN to IP CalleeID...............................................................................................97
3.11.6 PSTN to IP Original CalleeID..................................................................................98
3.11.7 CallerID Pool...........................................................................................................98
3.12 System Tools ............................................................................................... 99
3.12.1 Network ................................................................................................................101
3.12.2 Management.........................................................................................................102
3.12.3 SNMP Config........................................................................................................103
3.12.4 Radius ..................................................................................................................104
3.12.5 Configuration File..................................................................................................106
3.12.6 Signaling Capture.................................................................................................107
3.12.7 Signaling Call Test................................................................................................108
3.12.8 Signaling Call Track..............................................................................................109
3.12.9 PING Test .............................................................................................................110
3.12.10 TRACERT Test .....................................................................................................111
3.12.11 Modification Record..............................................................................................112
3.12.12 Backup & Upload..................................................................................................113
3.12.13 Factory Reset .......................................................................................................113
3.12.14 Upgrade................................................................................................................113
3.12.15 Change Password ................................................................................................114
3.12.16 Device Lock..........................................................................................................114
3.12.17 Restart..................................................................................................................115
Chapter 4 Typical Applications.....................................................116
4.1 Application 1...............................................................................................116
4.1.1 Configurations for Headquarters...........................................................................117
4.1.2 Configurations for Branch A..................................................................................119
4.1.3 Configurations for Branch B..................................................................................122
4.2 Application 2.............................................................................................. 126
4.2.1 Configurations for Headquarters...........................................................................126
4.2.2 Configurations for Branches .................................................................................129
Appendix A Technical Specifications...............................................130
All manuals and user guides at all-guides.com

Synway Information Engineering Co., Ltd
SMG Series Digital Gateway User Manual (Version 1.6.0) Page iii
Appendix B Troubleshooting............................................................131
Appendix C ISUP (ISDN) Pending Cause to SIP Status Code........132
Appendix D TUP Pending Cause to SIP Status Code .....................134
Appendix E Technical/sales Support ...............................................135
All manuals and user guides at all-guides.com

Synway Information Engineering Co., Ltd
SMG Series Digital Gateway User Manual (Version 1.6.0) Page iv
Copyright Declaration
All rights reserved; no part of this document may be reproduced or transmitted in any form or by
any means, electronic or mechanical, without prior written permission from Synway Information
Engineering Co., Ltd (hereinafter referred to as „Synway‟).
Synway reserves all rights to modify this document without prior notice. Please contact Synway
for the latest version of this document before placing an order.
Synway has made every effort to ensure the accuracy of this document but does not guarantee
the absence of errors. Moreover, Synway assumes no responsibility in obtaining permission and
authorization of any third party patent, copyright or product involved in relation to the use of this
document.
All manuals and user guides at all-guides.com

Synway Information Engineering Co., Ltd
SMG Series Digital Gateway User Manual (Version 1.6.0) Page v
Revision History
Version
Date
Comments
Version 1.3.0
2014-06
Initial publication.
Version 1.3.1
2014-08
New revision
Version 1.3.2
2014-10
New revision
Version 1.5.0
2014-12
Add description on the new series SMG3016
Version 1.5.1
2015-01
Add description on the new series SMG3008
Version 1.6.0
2015-03
New revision
Note: Please visit our website http://www.synway.net to obtain the latest version of this document.
All manuals and user guides at all-guides.com
all-guides.com

Synway Information Engineering Co., Ltd
SMG Series Digital Gateway User Manual (Version 1.6.0) Page 1
Chapter 1Product Introduction
Thank you for choosing Synway SMG Series Digital Gateway!
The Synway SMG series digital gateway products (hereinafter referred to as ‘SMG digital
gateway’) are mainly used for connecting PSTN or enterprise PBX with the IP telephony network
or IP PBX. It provides a powerful, reliable and cost-effective VoIP solution for such occasions as
IP call centers and multi-branch agencies.
The SMG series digital gateway has five models:
SMG2030: 1 E1/T1 interface (30 digital ports)
SMG2060: 2 E1/T1 interfaces (60 digital ports)
SMG2120: 4 E1/T1 interfaces (120 digital ports)
SMG3008: 8 E1/T1 interfaces (240 digital ports)
SMG3016: 16 E1/T1 interfaces (480 digital ports)
1.1 Typical Application
Branch B
Subscriber
Terminal
IP Phone IP Phone
SMG Digital
Gateway
LAN
Router
E1
IP PBX
Headquarters
SMG Digital Gateway
E1
Router
FXS
PBX
Tel Tel Tel
E1
SIP
Branch A
SMG Digital Gateway
SIP E1
FXS
PBX
Tel Tel Tel
Router
Internet
Tel Tel Fax Fax
……
PSTN
Figure 1-1 Typical Application
All manuals and user guides at all-guides.com

Synway Information Engineering Co., Ltd
SMG Series Digital Gateway User Manual (Version 1.6.0) Page 2
1.2 Feature List
Basic Features
Description
PSTN Call
Call initiated from PSTN to a designated SIP trunk, via routing and number
manipulation.
IP Call
Call initiated from IP to a designated PCM trunk, via routing and number
manipulation.
Number Manipulation
Peels off some digits of a phone number from left/right, or adds a prefix/suffix to a
phone number.
PSTN/ VoIP Routing
Routing path: from IP to PSTN or from PSTN to IP.
Fax
Multiple fax parameters: fax mode, maximum fax rate, fax train mode, error
correction mode, etc.
Echo Cancellation
Provides the echo cancellation feature for a call conversation.
Signaling & Protocol
Description
SS7
SS7-TUP, SS7-ISUP
ISDN
ISDN User Side, ISDN Network Side
SS1
SS1 Signaling
SIP Signaling
Supported protocol: SIP V1.0/2.0, RFC3261
Voice
CODEC
G.711A, G.711U, G.729A/B, G723, G722, AMR, iLBC
DTMF Mode
RFC2833, SIP INFO, INBAND
Fax
Fax Mode
T.38, Pass-Through
Baud Rate
14400bps, 9600bps, 4800bps
Network
Description
Network Protocol
Supported protocol: TCP/UDP, HTTP, ARP/RARP, DNS, NTP, TFTP, TELNET,
STUN
Static IP
IP address modification support
DNS
Domain Name Service support
Security
Description
Admin Authentication
Support admin authentication to guarantee the resource and data security
Maintain & Upgrade
Description
WEB Configuration
Support of configurations through the WEB user interface
Language
Chinese, English
Software Upgrade
Support of user interface, gateway service, kernel and firmware upgrades based
on WEB
Tracking Test
Support of Ping and Tracert tests based on WEB
All manuals and user guides at all-guides.com

Synway Information Engineering Co., Ltd
SMG Series Digital Gateway User Manual (Version 1.6.0) Page 3
SysLog Type
Three options available: ERROR, WARNING, INFO
1.3 Hardware Description
The SMG digital gateway features 1U rackmount design and integrates embedded LINUX system
within the POWERPC+DSP hardware architecture. It has 1/2/4/8/16 E1/T1 ports and 2
Kilomega-Ethernet ports (LAN1 and LAN2) on the chassis.
（a）See below figures for SMG20000 series appearance：
Figure 1-2 Front View
Figure 1-3 Rear View
Figure 1-4 Left View
（b）See below figures for SMG3000 series appearance：
Figure 1-5 Front View
Ventilation
Holes
Screw Holes for
Foot Bracket
Power1 Key
220V AC
Power1
220V AC
Power2
Power2 Key
E1/T1
Interface
LAN
Grounding
Stud
LAN1 Indicator
Alarm Indicator
Power 1 Indicator
LAN2 Indicator
Console Port
Run Indicator
PCM Indicator
Power 2 Indicator
Reset Button
LAN1 Indicator
Alarm Indicator
Power 1 Indicator
LAN2 Indicator
Console Port
Run Indicator
PCM Indicator
Power 2 Indicator
Reset Button
All manuals and user guides at all-guides.com

Synway Information Engineering Co., Ltd
SMG Series Digital Gateway User Manual (Version 1.6.0) Page 4
Figure 1-6 Rear View
Note: The left view for SMG3000 series is same as that for SMG2000 series, refer to Figure 1-4.
The table below gives a detailed introduction to the interfaces, buttons and LEDs illustrated
above:
Interface
Description
LAN
Amount: 2
Type: RJ-45
Bandwidth: 10/100/1000Mbps
Self-Adaptive Bandwidth Supported
Auto MDI/MDIX Supported
E1/T1
Amount: 1/2/4/8/16
Type: RJ-45
Console Port
Amount: 1
Type: RS-232
Baud Rate: 115200 bps
Connector: RJ45 (See Figure 1-7 for signal definition)
Data Bits: 8 bits
Stop Bit: 1 bit
Parity Unsupported
Flow Control Unsupported
Button
Description
Power Key
Power on/off the SMG digital gateway. You can turn on the two power keys at the
same time to have the power supply working in the hot-backup mode.
Reset Button
Restore the gateway to factory settings.
LED
Description
Power Indicator
Indicates the power state. It lights up when the gateway starts up with the power
cord well connected.
Run Indicator
Indicates the running status. For more details, refer to 1.4 Alarm Info.
Alarm Indicator
Alarms the device malfunction. For more details, refer to 1.4 Alarm Info.
Link Indicator
The green LED on the left of LAN, indicating the network connection status.
ACT Indicator
The orange LED on the right of LAN, whose flashing tells data are being
transmitted.
E1/T1 Indicators
The green LED on the right of E1/T1 interface lights up and keeps on after the
E1/T1 module is successfully synchronized.
Power1 Key
220V AC
Power1
220V AC
Power2
Power2 Key
E1/T1
Interface
LAN
Grounding
Stud
All manuals and user guides at all-guides.com

Synway Information Engineering Co., Ltd
SMG Series Digital Gateway User Manual (Version 1.6.0) Page 5
Channel Indicators
Indicates the synchronization status of E1/T1 channels. It will light up and keep on
if E1/T1 is synchronized; otherwise, it will go out.
Note: The console port is used for debugging. While connection, the transmitting and receiving
lines of the gateway and the remote device should be cross-linked. That is, connect the
transmitting line of the gateway to the receiving line of the remote device, and vice verse. The
figure below illustrates the signal definition of the console port on the gateway.
Figure 1-7 Console Port Signal Definition
For other hardware parameters, refer to Appendix A Technical Specifications.
1.4 Alarm Info
The SMG digital gateway is equipped with two indicators denoting the system‟s running status:
Run Indicator (green) and Alarm Indicator (red). The table below explains the states and
meanings of the two indicators.
LED
State
Description
Run Indicator
Go out
System is not yet started.
Light up
System is starting.
Flash
Device is running normally.
Alarm Indicator
Go out
Device is working normally.
Light up
Upon startup: Device is running normally.
In runtime: Device goes abnormal.
Flash
System is abnormal.
Note:
The startup process consists of two stages: System Booting and Gateway Service
Startup. The system booting costs about 1 minute and once it succeeds, both the run
indicator and the alarm indicator light up. Then after the gateway service is successfully
started and the device begins to work normally, the run indicator flashes and the alarm
indicator goes out.
During runtime, if the alarm indicator lights up or flashes, it indicates that the device goes
abnormal. If you cannot figure out and solve the problem by yourself, please contact our
technicians for help. Go to Appendix E Technical/sales Support to find the contact way.
8
7
6
5
4
3
2
1
GND
Gateway TX
Gateway RX
All manuals and user guides at all-guides.com
all-guides.com

Synway Information Engineering Co., Ltd
SMG Series Digital Gateway User Manual (Version 1.6.0) Page 6
Chapter 2Quick Guide
This chapter is intended to help you grasp the basic operations of the SMG digital gateway in the
shortest time.
Step 1: Confirm that your packing box contains all the following things.
SMG Series Digital Gateway *1
Angle Bracket *2, Rubber Foot Pad *4, Screw for Angle Bracket *8
220V Power Cord *2
Warranty Card *1
Installation Manual *1
Step 2: Properly fix the SMG digital gateway.
If you do not need to place the gateway on the rack, simply fix the 4 rubber foot pads. Otherwise,
you should first fix the 2 angle brackets onto the chassis and then place the chassis on the rack.
Step 3: Connect the power cord.
Make sure the device is well grounded before you connect the power cord. Check if the power
socket has the ground wire. If it doesn‟t, use the grounding stud on the rear panel of the device
(See Figure 1-3) for earthing.
Note: Each SMG digital gateway has two power interfaces to meet the requirement for power
supply hot backup. As long as you properly connect and turn on these two power keys, either
power supply can guarantee the normal operation of the gateway even if the other fails.
Step 4: Connect the network cable.
Step 5: Connect the E1/T1 trunk. Connect the E1/T1 interface of the digital gateway to that
of the remote device by E1/T1 trunk. After connection, check if the synchronization
indicator (green LED) is lit and keeps on, which indicates that the E1/T1 trunk is well
connected and the E1/T1 module is successfully synchronized.
For the 75Ω-unbalanced coaxial cable, in consideration of various line conditions, each PCM on
the digital gateway is equipped with two grounding jumpers which respectively control the
grounding of the transmitting and the receiving end. Under normal condition, that is, the chassis of
the gateway is well grounded, the grounding jumpers at the receiving end should be disconnected
and the ones at the transmitting end should be short-circuited. This configuration is the factory
default setting and applicable in most situations so that there is usually no need to change it. For
the 120Ω-balanced twisted pair cable, the grounding jumpers at both ends should be
disconnected.
You can construct an E1 trunk according to Figure 2-1. Prevent reverse connection of the
transmitting and receiving lines. The state of the receiving line can be checked by the
synchronization indicator (green LED) of the E1 interface. When the receiving line is in a normal
state, the indicator is lit and keeps on. If the indicator is off or flashing, it means that the
connection of the receiving line may probably be reversed. However, the state of the transmitting
line can only be examined by the opposite terminal. The synchronization indicator starts working
only after the device is powered on and successfully initialized.
8
7
6
5
4
3
2
1
RTip
RRing
Receive
TTip
TRing
Transmit
All manuals and user guides at all-guides.com

Synway Information Engineering Co., Ltd
SMG Series Digital Gateway User Manual (Version 1.6.0) Page 7
Figure 2-1 Pin Layout for E1 Interface
Step 6: Log in the gateway.
Enter the original IP address (LAN 1: 192.168.1.101 or LAN 2: 192.168.0.101) of the SMG digital
gateway in the browser to go to the WEB interface. The original username and password of the
gateway are both „admin‟. For detailed instructions about login, refer to 3.1 System Login. We
suggest you change the initial username and password via „System Tools Change Password‟
on the WEB interface as soon as possible after your first login. For detailed instructions about
changing the password, refer to 3.12.15 Change Password. After changing the password, you are
required to log in again.
Step 7: Modify IP address of the gateway.
You can modify the IP address of the gateway via „System Tools Network‟on the WEB interface
to put it within your company‟s LAN. Refer to 3.12.1 Network for detailed instructions about IP
modification. After changing the IP address, you shall log in the gateway again using your new IP
address.
Step8: Set PCM.
On your initial use of the SMG digital gateway, you shall enter the PCM interface and set the
configuration items „Signaling Protocol‟and „Interface‟. These items must be in conformity with the
physical connection. You may use the default values of other configuration items. Refer to 3.4.3
PCM for detailed instructions about PCM Settings.
Note: You shall restart the service to validate the settings in this step. Refer to 3.12.17 Restart for
detailed instructions.
Step 9: Configure signaling protocol parameters.
Further configure the signaling protocol you set in Step 8. Different protocols are configured on
different interfaces. See below for detailed instructions.
SS7-ISUP:
Note: For your easy understanding and manipulation, this step does not involve the ISUP
quasi-associated mode configuration and the dual gateway feature. For descriptions about
these configurations, refer to 3.5 SS7 Settings.
The configuration interfaces related to SS7-ISUP include: SS7, ISUP and SS7 Server.
On your initial use of the SMG digital gateway, you may adopt the default values of the
configuration items on the SS7 and ISUP interfaces. Note that the SS7 Server interface must be
configured properly. Otherwise, the PSTN trunks may be unavailable. Follow the instructions here
to configure the SS7 Server:
Step 1: Set OPC, Server IP and Signaling Point Code Standard. The OPC is generally allocated
by the central office. The Server IP is the IP address of the SS7 server and you may use
its default value. The Signaling Point Code Standard, which varies on the PBX model,
can be set to 24 or 14. After modification, click the ‘Modify’button on the right to save
the settings.
Step 2: Modify the current link or click the „Add New‟button below the signaling link list to add a
new link. Enter the physical address of the actually used signaling PCM (E1 interface)
and click „Save‟to save the modification. If only one PCM is used for signaling in the
gateway, you need just configure one signaling link.
Step 3: Modify the current linkset or click the „Add New‟button below the signaling linkset list to
add a new linkset. You shall select the link configured in Step 2 for „Link‟and use the
default values for the other configuration items. After modification, click ‘Save’.
Step 4: Modify the current DPC or click the „Add New‟button below the DPC list to add a new
DPC. Fill in „SP Code‟with the signaling point code of the remote end (i.e. signaling
destination), select the linkset configured in Step 3 for „Linkset‟and use the default
values for the other configuration items. After modification, click ‘Save’.
All manuals and user guides at all-guides.com

Synway Information Engineering Co., Ltd
SMG Series Digital Gateway User Manual (Version 1.6.0) Page 8
Step 5: Modify the current CIC routing rule or click the „Add New‟button below the ISUP_CIC
routing rule list to add a new CIC routing rule. Select the DPC configured in Step 4 for
„DPC‟, fill in „CIC_PCM‟according to the actual allocation and use the default values for
the other configuration items. After modification, click ‘Save’. Note that if multiple PCMs
in the gateway are used for voice transmission, they should be configured with multiple
CIC routing rules accordingly.
Note: After configuring SS7-ISUP related interfaces, you shall restart the service to validate the
settings. Refer to 3.12.17 Restart for detailed instructions.
SS7-TUP:
Note: For your easy understanding and manipulation, this step does not involve the TUP
quasi-associated mode configuration and the dual gateway feature. For descriptions about
these configurations, refer to 3.5 SS7 Settings.
The configuration interfaces related to SS7-TUP include: SS7, TUP and SS7 Server.
On your initial use of the SMG digital gateway, you may adopt the default value of the
configuration items on the SS7 and TUP interfaces. Note that the SS7 Server interface must be
configured properly. Otherwise, the PSTN trunks may be unavailable. Follow the instructions here
to configure the SS7 Server:
Step 1: Set OPC, Server IP and Signaling Point Code Standard. The OPC is generally allocated
by the central office. The Server IP is the IP address of the SS7 server and you may use
its default value. The Signaling Point Code Standard, which varies on the PBX model,
can be set to 24 or 14. After modification, click the ‘Modify’button on the right to save
the settings.
Step 2: Modify the current link or click the „Add New‟button below the signaling link list to add a
new link. Enter the physical address of the actually used signaling PCM (E1 interface)
and click „Save‟to save the modification. If only one PCM is used for signaling in the
gateway, you need just configure one signaling link.
Step 3: Modify the current linkset or click the „Add New‟button below the signaling linkset list to
add a new linkset. You shall select the link configured in Step 2 for „Link‟and use the
default values for the other configuration items. After modification, click ‘Save’.
Step 4: Modify the current DPC or click the „Add New‟button below the DPC list to add a new
DPC. Fill in „SP Code‟with the signaling point code of the remote end (i.e. signaling
destination), select the linkset configured in Step 3 for „Linkset‟and use the default
values for the other configuration items. After modification, click ‘Save’.
Step 5: Modify the current CIC routing rule or click the „Add New‟button below the TUP_CIC
routing rule list to add a new CIC routing rule. Select the DPC configured in Step 4 for
„DPC‟, fill in „CIC_PCM‟according to the actual allocation and use the default values for
the other configuration items. After modification, click ‘Save’. Note that if multiple PCMs
in the gateway are used for voice transmission, they should be configured with multiple
CIC routing rules accordingly.
Note: After configuring SS7-TUP related interfaces, you shall restart the service to validate the
settings. Refer to 3.12.17 Restart for detailed instructions.
ISDN User Side/Network Side:
The configuration interface related to ISDN User Side/Network Side is ISDN. On your initial use of
the SMG digital gateway, you may adopt the default value of the configuration items on this
interface.
Note: After configuring the ISDN interface, you shall restart the service to validate the settings.
Refer to 3.12.17 Restart for detailed instructions.
SS1:
The configuration interface related to SS1 is SS1. On your initial use of the SMG digital gateway,
All manuals and user guides at all-guides.com

Synway Information Engineering Co., Ltd
SMG Series Digital Gateway User Manual (Version 1.6.0) Page 9
you may adopt the default value of the configuration items on this interface.
Note: After configuring the SS1 interface, you shall restart the service to validate the settings.
Refer to 3.12.17 Restart for detailed instructions.
Step 10: Check the PSTN status.
After the configuration of signaling protocols, you can check the status of the PSTN trunks via
„Operation Info PSTN Status‟. Refer to 3.2.2 PSTN Status for detailed introductions. When
Time Slot 0 shows „Frame Synchronized‟, the signaling time slot is in the state of „Signaling
Channel‟and all the other channels are „Idle‟, it indicates the PCM is well configured. If Time Slot
0 or the signaling time slot shows „Faulty‟or the other channels are in the state of „Unavailable‟,
there may be errors in the signaling protocol configurations and we suggest you return to Step 9
for check.
Step 11: Set routing rules for calls.
Note: For your easy understanding and manipulation, all examples given in this step do not
involve registration.
Situation 1: IP PSTN
Step 1: Configure the IP address of the remote SIP terminal which can establish conversations
with the gateway so that the calls from other terminals will be ignored. Refer to „VOIP
Settings SIP Trunk‟for detailed instructions. Fill in „Remote IP‟and „Remote Port‟with
the IP address and port of the remote SIP terminal which will initiate calls to the gateway.
You may use the default values for the other configuration items.
Example: Provided the IP address of the remote SIP terminal is 192.168.0.111 and the
port is 5060. Add SIP Trunk 0; set Remote IP to 192.168.0.111 and Remote Port to
5060.
Step 2: Add the IP address of the remote SIP terminal configured in Step 1 into the
corresponding SIP trunk group. Refer to „VoIP Settings SIP Trunk Group‟for detailed
instructions. Select the SIP trunk configured in Step 1 as „SIP Trunks‟. You may use the
default values for the other configuration items.
Example: Add SIP Trunk Group 0. Check the checkbox before 0for SIP Trunks and
keep the default values for the other configuration items.
Step 3: Add PCM into the corresponding PCM Group. Refer to „PCM Settings PCM Trunk
Group‟for detailed instructions. Select the PCM used for call conversation as „PCM‟. You
may use the default values for the other configuration items.
Example: Provided the PCM used for call conversation is PCM[1]. Add PCM Trunk
Group 0, check the checkbox before PCM[1] and keep the default values for the other
configuration items.
Step 4: Add routing rules. Refer to „Route Settings IPPSTN‟for detailed instructions. Select
the SIP trunk group set in Step 2 as „Call Initiator‟and the PCM trunk group set in Step 3
as „Call Destination‟. You may use the default values for the other configuration items.
Example: Select SIP Trunk Group[0] as Call Initiator and PCM Trunk Group[0] as
Call Destination. Keep the default values for the other configuration items.
Step 5: Initiate a call from the SIP terminal configured in Step 1 to the IP address and port of the
SMG digital gateway. Thus you can establish a call conversation via PCM[1] with the
PSTN terminal. (Note: The format used for calling an IP address via SIP trunk is as
follows: username@IP address, in which, „username‟is a called party number which
conforms to the number-receiving rule of the remote device.)
Example: Provided the IP address of the SMG digital gateway is 192.168.0.101 and the
port is 5060. Provided 123 is a number which conforms to the number receiving rule of
the remote device. Initiate a call from SIP terminal 0 to the IP address 192.168.0.101 (in
the format: 123@192.168.0.101) and you can establish a call conversation via PCM[1] to
All manuals and user guides at all-guides.com

Synway Information Engineering Co., Ltd
SMG Series Digital Gateway User Manual (Version 1.6.0) Page 10
the number 123.
Situation 2: PSTN IP
Step 1: Configure the called party numbers which are received from PSTN and will be processed
by the gateway. Refer to „Advanced Settings Number-receiving Rule‟for detailed
instructions. Enter either a particular number or a string of „x‟s to represent several
random numbers. For example, „xxx‟denotes 3 random numbers. You may use the
default value for „Index‟.
Example: Set Index to 99 and configure Dial Rule to 123.
Step 2: Set the IP address of the SIP terminal to be called by the gateway. Refer to „VOIP
Settings SIP Trunk‟for detailed instructions. Fill in „Remote IP‟and „Remote Port‟with
the IP address and port of the SIP trunk. You may use the default values for the other
configuration items.
Example: Provided the IP address of the SIP trunk to be called is 192.168.0.111 and the
port is 5060. Add SIP Trunk 0; set Remote IP to 192.168.0.111 and Remote Port to
5060.
Step 3: Add the IP address of the remote SIP terminal configured in Step 2 into the
corresponding SIP trunk group. Refer to „VoIP Settings SIP Trunk Group‟for detailed
instructions. Select the SIP trunk configured in Step 2 as „SIP Trunks‟. You may use the
default values for the other configuration items.
Example: Add SIP Trunk Group 0. Check the checkbox before 0for SIP Trunks and
keep the default values for the other configuration items.
Step 4: Add PCM into the corresponding PCM Group. Refer to „PCM Settings PCM Trunk
Group‟for detailed instructions. Select the PCM used for call conversation as „PCM‟. You
may use the default values for the other configuration items.
Example: Provided the PCM used for call conversation is PCM[1]. Add PCM Trunk
Group 0, check the checkbox before PCM[1] and keep the default values for the other
configuration items.
Step 5: Add routing rules. Refer to „Route Settings PSTNIP‟for detailed instructions. Select
the PCM trunk group set in Step 4 as „Call Initiator‟and the SIP trunk group set in Step 3
as „Call Destination‟. You may use the default values for the other configuration items.
Example: Select PCM Trunk Group[0] as Call Initiator and SIP Trunk Group[0] as
Call Destination. Keep the default values for the other configuration items.
Step 6: Once PCM[1] receives a call from PSTN and the called party number conforms to the
number-receiving rules set in Step 1, it can establish a call conversation with the remote
SIP terminal via the gateway.
Example: Once PCM[1] receives a call from PSTN with the called party number 123, it
will route the call to SIP Trunk 0 of the gateway.
Special Instructions:
The chassis of the SMG digital gateway must be grounded for safety reasons, according
to standard industry requirements. A simple way is earthing with the third pin on the plug
or the grounding studs on the machine. No or improper grounding may cause instability
in operation as well as decrease in lightning resistance.
As the device will gradually heat up while being used, please maintain good ventilation to
prevent sudden failure, ensuring that the ventilation holes (see Figure 1-4) are never
jammed.
During runtime, if the alarm indicator lights up or flashes, it indicates that the device goes
abnormal. If you cannot figure out and solve the problem by yourself, please contact our
All manuals and user guides at all-guides.com
all-guides.com

Synway Information Engineering Co., Ltd
SMG Series Digital Gateway User Manual (Version 1.6.0) Page 11
technicians for help. Otherwise it may lead to a drop in performance or unexpected
errors.
All manuals and user guides at all-guides.com

Synway Information Engineering Co., Ltd
SMG Series Digital Gateway User Manual (Version 1.6.0) Page 12
Chapter 3WEB Configuration
3.1 System Login
Type the IP address into the browser and enter the login interface. See Figure 3-1.
Figure 3-1 Login Interface
The gateway only serves one user, whose original username and password are both „admin‟. You
can change the username and the password via „System Tools Change Password‟on the WEB
interface. For detailed instructions, refer to 3.12.15 Change Password.
After login, you can see the main interface as below.
Figure 3-2 Main Interface
All manuals and user guides at all-guides.com

Synway Information Engineering Co., Ltd
SMG Series Digital Gateway User Manual (Version 1.6.0) Page 13
3.2 Operation Info
Operation Info includes four parts: System Info, PSTN Status, SS7 Server and Call Count,
showing the current running status of the gateway. See Figure 3-3.
Figure 3-3 Operation Info
3.2.1 System Info
Figure 3-4 System Info Interface
See Figure 3-4 for the system info interface. You can click Refresh to obtain the latest system
All manuals and user guides at all-guides.com

Synway Information Engineering Co., Ltd
SMG Series Digital Gateway User Manual (Version 1.6.0) Page 14
information. The table below explains the items shown in Figure 3-4.
Item
Description
MAC Address
MAC address of LAN 1 or LAN 2.
IP Address
The three parameters from left to right are IP address, subnet mask and default
gateway of LAN 1 or LAN 2.
DNS Server
DNS server address of LAN 1 or LAN 2.
Receive Packets
The amount of receive packets after the gateway‟s startup, including three
categories: All, Error and Drop.
Transmit Packets
The amount of transmit packets after the gateway‟s startup, including three
categories: All, Error and Drop.
Current Speed
The current speed of data receiving and transmitting.
Work Mode
The work mode of the network, including five options: 10 Mbps Half Duplex, 10
Mbps Full Duplex, 100 Mbps Half Duplex, 100 Mbps Full Duplex and 1000 Mbps
Full Duplex.
Runtime
Time of the gateway keeping running normally after startup. This parameter
updates every 2s.
Operating Mode
The operating mode of the gateway includes:
Operating Mode
Description
Master Server
The current gateway applies the SS7 protocol and is
used for both signaling and voice transmission. If the
dual gateway feature is enabled, the current gateway
serves as the master server.
Slave Server
The current gateway applies the SS7 protocol and is
used for both signaling and voice transmission. This
operating mode works only when the dual gateway
feature is enabled and the current gateway serves as the
slave server.
Client
The current gateway applies the SS7 protocol and is
only used for voice transmission.
ISDN(User-side)
The current gateway is configured to be ISDN user-side..
ISDN(Network-side)
The current gateway is configured to be ISDN
network-side.
SS1
The current gateway is configured to be SS1.
Serial Number
Unique serial number of an SMG digital gateway.
WEB
Current version of the WEB interface.
Gateway
Current version of the gateway service.
Uboot
Current version of Uboot.
Kernel
Current version of the system kernel on the gateway.
Firmware
Current version of the firmware on the gateway.
All manuals and user guides at all-guides.com