T.D.S. C-82651 User manual

C-82651 - LOWER BACK EXTENSION MACHINE
ARM PAD MOUNT ARM PAD (2)
(3) HIP PAD
MOUNT
(8)
FRAME
SOCKET
(5)
(2)
(2)
FRAME
(2)
BASE
REAR
UPRIGHT
STRUT (2) (1)
(7)
4 X 8 CUSHION (2)
SWING ARM
INSERT
MEASURE
DISTANCE
(7)
(6)
PILLOW BLOCK
BEARING (2)
(6)
SWING ARM
(2)
(9)
HIP PAD (2)
DRAWING # 1
T.D.S. FITNESS EQUIPMENT
P.O. BOX 4189
ELMIRA, NY 14904, USA
607-733-6789
WEIGHT BAR COLLARS (4)

DRAWING # 2
DRAWING # 4
DRAWING # 3
(7)
SNAP
RING
(2)
PILLOW
BLOCK
(6)
SWING
ARM
3/8 X 3/4” BOLT
REAR UPRIGHT
(4) 3/8 X 3”
BOLT
FRAME
(2)
REAR UPRIGHT
HIP PAD
MOUNT
C-82651 - LOWER BACK EXTENSION MACHINE

C-82651 - LOWER BACK EXTENSION MACHINE
DRAWING # 5DRAWING # 5
SIDESIDE
SOCKET ARM
PAD MOUNT
SOCKET
SIDESIDE
SIDE
2 PCS
SIDE
2 PCS
(3)(3)

HIP PAD
MOUNT 1PC
ARM PAD
MOUNT 1PC
BASE 1PC
SWING ARM
SOCKET 2PCS
FRAME 1PC
FRAME
SOCKET 1PC
WEIGHT BAR 1PC
ARM PAD 2PCS
HIP PAD
2PCS
REAR
UPRIGHT
1PC
STRUT
2PCS
SWING ARM
INSERT 2PCS
PILLOW BLOCK
BEARINGS 2PCS - 1PKG
HARDWARE 1 PKG LITERATURE 1PKG
4 X 8 CUSHION 2PCS
C-82651 - LOWER BACK EXTENSION MACHINE
PACKING LIST

C-82651 LOWER BACK EXTENSION MACHINE
ASSEMBLY INSTRUCTIONS
THIS UNIT REQUIRES (2) 9/16 WRENCHES, (1) 11/16 WRENCH, (1) TAPE MEASURE, (2) 3/4
WRENCHES AND (1) SET OF ALLEN WRENCHES FOR ASSEMBLY. DO NOT TIGHTEN
HARDWARE UNTIL INSTRUCTED TO.
SEE DRAWING #1
(1) PUSH (3) 2 X 4 FOOT ONTO BASE. ATTACH REAR UPRIGHT TO BASE WITH (2) 3/8 X 3
BOLTS, (1) 3/8 X 5 BOLT, (6) 3/8 FLAT WASHERS AND (3) 3/8 LOCKNUTS.
SEE DRAWING #1 AND #2
(2) SLIDE FRAME SOCKET ONTO FRAME. FASTEN WITH (1) "L" PIN AND (2) HAND KNOBS.
ATTACH FRAME TO BASE WITH (2) 3/8 X 3 BOLTS, (4) 3/8 FLAT WASHERS AND (2) 3/8
LOCKNUTS. ATTACH FRAME TO REAR UPRIGHT WITH (3) 3/8 X 3/4 BOLTS AND (3) 3/8 FLAT
WASHERS.
(3) ATTACH (2) SIDES TO (1) SOCKET WITH (4) 3/8 X 3 BOLTS, (8) FLAT 3/8 WASHERS & (4) 3/8
LOCK NUTS. TIGHTEN HARDWARE. PUSH (2) HANDLES ONTO ARM PAD MOUNT. PLACE ARM
PAD MOUNT OVER FRAME SOCKET, FASTEN WITH TURN POP PIN AND (1) HAND KNOB.
SEE DRAWING #3
(4) ATTACH HIP PAD MOUNT TO REAR UPRIGHT WITH (2) 3/8 X 3 BOLTS, (1) 3/8 X 3/4 BOLT,
(5) 3/8 FLAT WASHERS AND (2) 3/8 LOCKNUTS.
SEE DRAWING #1
(5) ATTACH (2) STRUT TO THE HIP PAD MOUNT WITH (4) 3/8 X 3 BOLTS, (8) 3/8 FLAT WASHERS
AND (4) 3/8 LOCKNUTS. SET UNIT ON LEVEL SURFACE AND TIGHTEN HARDWARE. USE BOLT
ON BOTTOM OF STRUTS TO LEVEL UNIT.
SEE DRAWING #1 AND #4
(6) ATTACH (2) PILLOW BLOCKS TO HIP PAD MOUNT WITH (4) 1/2 X 3 1/2 BOLTS, (8) 1/2 FLAT
WASHERS AND (4) 1/2 LOCKNUTS.
(7) PUSH (2) SWING ARM PINS THRU (2) PILLOW BLOCKS. INSTALL (2) TURN POP PINS INTO
SWING ARMS. PUSH (2) INSERTS INTO SWING ARMS. SET LENGTH WITH TURN POP PINS AND
(2) HAND KNOBS. REMOVE (4) COLLARS FROM WEIGHT BAR. PUSH BAR THRU ONE SWING
ARM, PLACE ON COLLAR ON WEIGHT BAR. PUSH (2) 4 X 8 CUSHIONS ON WEIGHT BAR.
PLACE ONE COLLAR ON WEIGHT BAR. PUSH WEIGHT BAR THRU OTHER SWING ARM.
MEASURE DISTANCE BETWEEN TOP AND BOTTOM OF SWING ARM. TIGHTEN ALLEN SCREWS

ON PILLOW BLOCKS. PUSH (2) SNAP TOOTH RINGS ONTO SWING ARM SHAFT ON INSIDE OF
PILLOW BLOCKS. TIGHTEN INSIDE COLLARS ON WEIGHT BARS. RECHECK DIMENSION ON
TOP AND BOTTOM OF SWING ARM. ADJUST INSIDE COLLARS TO HOLD DIMENSION.
INSTALL OUTSIDE COLLARS AND TIGHTEN SET SCREWS. INSTALL (2) WEIGHT COLLARS.
(8) ATTACH (2) ARM PAD TO ARM PAD MOUNT WITH (4) 3/8 X 2 1/2 BOLTS AND (4) 3/8 FLAT
WASHERS FINGER TIGHT. CENTER ARM PADS AND TIGHTEN HARDWARE. DO NOT OVER
TIGHTEN.
(9) ATTACH (2) HIP PAD TO HIP PAD MOUNT WITH (4) 3/8 X 1 BOLTS AND (4) 3/8 FLAT
WASHERS FINGER TIGHT. CENTER PADS AND TIGHTEN HARDWARE. DO NOT OVER TIGHTEN.
(10) INSTALL (11) 2 PLUGS AND (2) 1 3/4 PLUGS.
HARDWARE LIST
(4) 3/8 X 3/4 BOLTS
(4) 3/8 X 2 1/2 BOLTS
(14) 3/8 X 3 BOLTS
(1) 3/8 X 5 BOLT
(4) 3/8 X 1 BOLTS
(42) 3/8 FLAT WASHERS
(15) 3/8 LOCKNUTS
(4) 1/2 X 3 1/2 BOLTS
(8) 1/2 FLAT WASHERS
(4) 1/2 LOCKNUTS
(5) 3/8 HANDKNOB
(2) 3/8 POP PIN
(3) 3/8 "L" PIN
(3) 2 X 4 FOOT
(11) 2 PLUG
(2) 1 3/4 PLUG
(2) 1 HANDLE
(2) 1 WEIGHT COLLARS
(2) 3/4 SNAP TOOTH RING
(2) PILLOW BLOCK
(1) TURN POP PIN
NOTE: ALL ARE EXPRESSED IN INCHES.