T2 LUKE II User manual

LUKE®II KEYPAD
LIGHTING
INSTALLATION GUIDE
980.0144 REV. A

Luke®II Keypad Lighting Installation Guide
i
T2 Systems, Inc. | T2systems.com
WARRANTY STATEMENT
The product you have purchased is under warranty by T2 Systems Canada Inc. (T2) against defects in
workmanship and/or materials for one year from the date of original purchase. Parts that prove to be
defective within the one year period will be either repaired or replaced at the option of T2.
In order to return parts to T2 for repair or replacement, the client is to first contact T2 Technical Support at
1-888-687-6822 ext. 6426 or 604-688-1959 ext. 6426 to advise T2 of the part to be returned and its serial
number and to obtain a Return Merchandise Authorization (RMA) number. The part is to be returned to
T2 at the address to be specified by T2 Technical Support together with the RMA number.
T2 will fully test all repaired or replacement parts before returning them to the client. T2 will use
reasonable commercial efforts to ship repaired or replacement parts within five business days of their
receipt by T2. Parts will be shipped overnight, unless the client has indicated otherwise.
Repairs or replacement parts required as a result of rust or corrosion, damage due to accident, improper
handling or operation, improper maintenance, shipping damage, abuse, misuse, unauthorized repairs or
attempted repair, vandalism or “Acts of God” are not covered by warranty. In addition, the use of
unauthorized paper or other unauthorized components and/or supplies will void the warranty.
At no charge, T2 will also accept support phone calls during business hours (6:30 a.m. to 5:00 p.m.
Pacific Time, Monday to Friday) from clients who have purchased products directly from T2 for the first full
year after shipment. These phone calls are provided to aid in the initial setup and implementing the
products and implementation of processes or systems within your organization. Phone calls regarding
defective parts are not counted for this purpose. For more information, contact T2 Technical Support at
the abovementioned numbers.
This limited warranty is in lieu of all other warranties express or implied, including warranties of
merchantability and fitness for a particular purpose. In no event will T2 be liable to the client or to any
third-party for indirect damages or losses (in contract or in tort) in connection with the above-noted
warranty, including, but not limited to, damages for lost profits, lost savings or incidental, consequential or
special damages.
Please contact T2 to obtain a copy of the complete Warranty and Scope of Services contract to answer
any questions that may pertain to warranty services.
CONTACTING T2 SYSTEMS CANADA INC.
Toll Free: 1-888-687-6822
Phone: [phone]
Fax: [phone]
Web site: www.t2systems.com
Sales and Replacement Orders [e-mail]
Corporate Office
330 –4321 Still Creek Drive
Burnaby, B.C.
V5C 6S7
Production Facility (Shipping and Receiving)
4105 Grandview Highway
Burnaby, B.C.
V5C 6B4
Technical Support [e-mail]
1-888-687-6822 ext. 6426 or 604-688-1959 ext. 6426

Luke®II Keypad Lighting Installation Guide
ii
T2 Systems, Inc. | T2systems.com
DISCLAIMER
Copyright © 2015 T2 Systems, Inc.
All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or
transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise,
without the prior written permission of T2 Systems Canada Inc. (T2).
No patent liability is assumed with respect to the use of the information contained herein. Neither is any
liability assumed for damages resulting from the use of the information contained herein.
Neither T2 nor its affiliates shall be liable to the purchaser of this product or third-parties for damages,
losses, costs, or expenses incurred by purchaser or third-parties as a result of: accident, misuse, or
abuse of this product or unauthorized modifications, repairs, or alterations to this product, or failure to
strictly comply with T2’s operating and maintenance instructions.
T2 shall not be liable against any damages or problems arising from the use of any options or any
consumable products other than those designated as Original T2 Products.
General Notice: Other product names used herein are for identification purposes only and may be
trademarks of their respective owners. T2 disclaims any and all rights in those marks.
REVISION HISTORY
Version 1.0
November 2015

Luke®II Keypad Lighting Installation Guide
iii
T2 Systems, Inc. | T2systems.com
Contents
INSTALLING THE KEYPAD LIGHT ............................................................................................................1
Drill Mounting Holes..........................................................................................................................1
Install the Keypad Lighting Assembly.............................................................................................5
APPENDIX A –MASK TEMPLATE...........................................................................................................10

Luke®II Keypad Lighting Installation Guide
1
T2 Systems, Inc. | T2systems.com
INSTALLING THE KEYPAD LIGHT
T2 Systems has developed a new LED light fixture to illuminate the keypad of your Luke®II multi-space
pay station. The light is designed to help the consumer make an easier keypad selection, especially at
night if the unit is installed in a dimly lit location.
This document will guide you through the steps to install the light above your keypad. There will be some
drilling involved on the cabinet cast and door to affix the lighting assembly.
Drill Mounting Holes
Tools and Materials Required
Drill
Drill bits: 9/64in, 3/8in, 1/2in
Round file (for removing burrs)
Felt pen (for marking drill location)
Cardboard sheet, approximately 9x10in (to prevent scuffing the decal and keypad)
Cloth rag or paper towels to catch drill filings
Masking tape
Mask template (see Appendix A)
Zinc-rich paint:
□Contains more than 65 percent zinc powder, for restoring the zinc undercoat protection
after drilling the door:
Brite Zinc –aerosol spray
Rust-oleum –professional galvanizing compound spray
Rust-oleum –automotive galvanizing compound spray
Marine grease (we recommend Ultra Lube®marine grease or Lucas Oil®marine grease):
□For protecting the aluminum alloy cast after drilling
Q-tips (for applying grease)
Protective gloves
Safety goggles
Parts
Drill templates:
□160.0194 –Drill Template, Keypad Light –Front Cast
□160.0195 –Drill Template, Keypad Light –Door Inside

Luke®II Keypad Lighting Installation Guide
2
T2 Systems, Inc. | T2systems.com
Steps to Take:
1. Turn off power to the pay station.
2. On the outside of the door, place the Front Cast drill template around the keypad and mark the
three hole locations to be drilled in the cast above the keypad. Remove the template before
drilling the holes so that it can be re-used for multiple pay stations.
Note: If you have a 12-key keypad, center the template around
the keypad.
3. Place a piece of cardboard against the keypad and hold it in place with masking tape. This will
prevent the keypad and decal from getting scuffed during drilling.
4. Drill two holes into the cast using the drill with the 9/64in bit.
5. Drill one hole into the cast using the drill with the 3/8in bit.

Luke®II Keypad Lighting Installation Guide
3
T2 Systems, Inc. | T2systems.com
6. On the inside of the door, use the cloth rag (or paper towels) to cover the keypad, coin inlet
chute, and coin sensor to prevent metal filings from dropping into the electronic components.
a. If the RFID option is present, temporarily disconnect the data cable if it’s in your way.
7. Use the Door Inside drill template to mark the hole location to be drilled into the door.
8. Using the 1/2in bit, drill one hole into the door. You may want to drill a small pilot hole first to
guide the larger drill bit.

Luke®II Keypad Lighting Installation Guide
4
T2 Systems, Inc. | T2systems.com
a. Carefully clean away any remaining metal filings.
9. Use the file to remove any burrs from the drilled holes on the cast and door panel (inside and
outside edges).
10. To prevent rust, the hole in the door must be protected with a zinc-rich paint. If using a spray,
use a mask so as to prevent over-spray onto electronic components and cables. Allow 30
minutes for the paint to dry.
A mask template is provided at the end of this document.

Luke®II Keypad Lighting Installation Guide
5
T2 Systems, Inc. | T2systems.com
11. Since the cast is an aluminum-alloy, it does not need the zinc-rich paint. However, a thin
coating of marine grease is recommended. Carefully apply the marine grease to the three
holes in the front cast using a Q-tip.
Install the Keypad Lighting Assembly
Tool Required
Phillips screwdriver
Parts
1x Keypad Lighting Module
1x Cable, Keypad Lighting
1x Diffuser, Keypad Lighting

Luke®II Keypad Lighting Installation Guide
6
T2 Systems, Inc. | T2systems.com
2x Screws 8-18 x 3/4in FH Phil SS Drilling Tip
1x Grommet, Rubber for 1/2in Hole
2x Small cable ties
Steps to Take:
1. Install the grommet into the hole on the door panel.
2. Carefully insert the tail end of the flex PCB lighting assembly into the 3/8in hole in the cast, and
feed it through the grommet.
a. It might be easier to feed the mating cable connector through the grommet and out of the
hole in the cast, attach the lighting assembly, and then carefully guide the PCB tail into the
hole and through the grommet.
b. Be sure not to twist or crease the flex PCB as it is being guided through the holes.

Luke®II Keypad Lighting Installation Guide
7
T2 Systems, Inc. | T2systems.com
3. Attach the lighting assembly to the cast using the 2x #8 screws.
4. To attach the lighting cable, first disconnect the white LCD backlight connector. Then connect
the keypad lighting adapter cable to the LCD backlight, and the other end to the disconnected
backlight cable.

Luke®II Keypad Lighting Installation Guide
8
T2 Systems, Inc. | T2systems.com
5. If not already connected in step 2, connect the small connector to the keypad lighting tail
connector.
6. If the RFID cable was previously detached for access, re-attach it and install a new cable tie to
the anchor.
7. The keypad light cable can also be anchored to the LCD backlight cable with a cable tie.
8. Complete the lighting installation by installing the diffuser on top of the mounting screws and
lighting array.
9. Restore power to your pay station. The keypad light will activate once the pay station starts up.
The light will turn off when the pay station goes into sleep mode and will turn on again when a
key on the keypad is pressed.

Luke®II Keypad Lighting Installation Guide
9
T2 Systems, Inc. | T2systems.com
This completes the installation of your keypad light.

Luke®II Keypad Lighting Installation Guide
10
T2 Systems, Inc. | T2systems.com
APPENDIX A – MASK TEMPLATE

1"

Luke®II Keypad Lighting Installation Guide
11
T2 Systems, Inc. | T2systems.com
For Assistance or More Information
For any questions concerning procedures outlined in this Installation
Guide, please contact T2 Technical Support at 1-888-687-6822 ext.
6426 or 604-688-1959 ext. 6426, or e-mail
[e-mail].