Takara Belmont AK-S23S User manual

Model
AK-S23S
AK-S23SF
M o d e l
Assembly Instructions
February 2012 Second Version Request No. 1A08XGB0

<Before Assembling the Product>
Check the parts supplied with the product.
Prepare a No.2 Phillips‑head screwdriver for assembling.
Stand base ・・・・・・1 set Stand pole assembly ・・1 set
Upper main unit ・・1 set
Upper main unit cover・1 set
(with Fan)
Stand base cover・・・1 piece
Power cord・・・・1 set
Guide bar・・・・・1 set
Allen key wrench・・1 piece
*Opposite side: 4 mm
@Assembling the stand.
Upper main unit cover・1 set
Common Parts
Parts supplied depending on purchased specification
Specification w/o Fan Specification w/ Fan
【Assembling Procedures 】
Specification w/o Fan
Specification w/ Fan
A Installing the stand base cover.
B
CRaising and fixing the shaft.
DInstalling the guide bar.
EInstalling the upper main unit cover.
F Installing the upper main unit cover (w/ Fan).
GInstalling the pipe cover.
HAttaching the power cord.
I Completion.
Common Procedures
Common Procedures
Fixing the upper main unit onto the stand.
Checking of Operations
1
CAUTION Never take out the upper main unit from the carton box or
assemble the unit by holding it at the ring.
‑ M5 x 15 cap bolt (with spring washer) 7 pieces
‑ M4 x 12 binding‑head screw 2 pieces
‑ M4 x 12 (black) binding‑head screw 1 piece
‑ M3 x 15 pan‑head screw (with flat washer, spring washer) 1 piece
【Screws Supplied】
【Parts Supplied】
Power cord stopper・・1 piece

BFixing the upper main unit onto the stand.
Upper main unit
M5 x 15 cap bolt (with spring washer): 2 pieces
Insert the upper main unit into the stand pole,
and tighten it at two points with the supplied screws.
*Use the supplied L‑shaped wrench.
*Do not hold the unit at the ring when performing this procedure.
@Assembling the stand. AInstalling the stand base cover.
Stand base
Stand pole assembly
Stand base cover
M5 x 15 cap bolt : 4 pieces
(With a spring washer)
Latch of the stand base cover (8 latches)
Insert the stand pole into the stand base and tighten
at four points with the supplied screws.
* Use the supplied L‑shaped wrench.
Fix the stand base cover through the
stand pole.
*Install the stand base cover so that the latches
on the backside will hook onto the stand base.
2
*Tighten the stand pole firmly to prevent the unit from rattling.
*Tighten the screws firmly to prevent the unit from rattling.

Dropping the shaft may cause a strong impact that can result in a damage of the product.
Damage
Hold the shaft firmly with your hands throughout
the procedure of step . Never release your hands
from the shaft until you complete tightening the
screws.
Do not apply pressure onto the shaft.
*Doing so may cause a damage of the product.
CAUTION
Never release your hands from the shaft throughout the operation
of step . Doing so may cause an impact to the root of the shaft, resulting
in a damage of the product.
3

・ Raising and fixing the shaft.
CAUTION
１．Loosen the screws.
３．Tighten the screws.
Correct screw positions
Shaft
Hole for the lock screw
２．Tighten the screw.
Tighten the lower screw first, and then tighten the upper screw.
When the screws comes at the correct positions
(as per the illustration below), tighten the lock screw.
M5 x 15 cap bolt (with spring washer): 1 piece
*Use the allen key wrench supplied.
Loosen the screws on the shaft with the L-shaped wrench, raise the shaft up, and tighten with the lock screw.
Check that the screws are in the
correct positions when the shaft is
raised.
When the shaft comes at the appropriate position, tighten these screws
starting from the lower screw to firmly secure the shaft.
Appropriate Shaft Position
A
B
*The distances A and B should be almost the same.
This screw prevents the shaft from
falling when the screws that fixes
the shaft becomes loose.
If the lock screw is not tightened, the shaft may lift
from the friction, resulting in tumbling of the product.
CAUTION
4
*The shaft must be secured tightly since insufficient tightening may cause the
unit to rattle.
*Never release your hands from the shaft until you complete this procedure.
If A and B are not in the same distance,
you will not be able to install the pipe cover
correctly.

FInstalling the upper main unit cover (with Fan).
Specification w/ Fan
Specification w/o Fan
CAUTION
Make sure that the lead wire is not caught when installing the upper
main unit cover. Neglecting this caution may cause damage to the
product such as breaking of wire.
Connect the connector.
*Lead wire should not
get caught.
EInstalling the upper main unit cover.
M4 x 12 (black) binding‑head screw : 1 piece
Set the upper main unit cover.
*Pay attention to the position of the latches.
Fix the cover at one point with the supplied screw.
*Use the Phillips‑head screwdriver.
DInstalling the guide ba r.
Guide bar
M4 x 12 binding‑head screw : 2 pieces
Insert the guide bar into the main unit and secure it with the two supplied screws.
*Use the Phillips‑head screwdriver.
(Black) Binding‑head screw M4 x 12: 1 piece
Set the upper main unit cover.
*Pay attention to the positions of the latches.
Fix the cover at one point with the supplied
screw.
*Use the Phillips‑head screwdriver.
5

GInstalling the pipe cover.
HAttaching the power cord. I Completion.
Fit the latch into the pitted
area on the cover.
A space is created at the rear end of the
pipe cover.
A gap can be seen between the
pipe cover and the main unit cover.
Correctly Installed Pipe Cover
M3 x 15 pan‑head screw
(with flat washer, spring washer): 1 piece
Fit in the pipe cover.
Above illustration shows a shaft inclined forward. Above illustration shows a shaft inclined backward
Information
*Insert the latch provided at the
back of the pipe cover into the
pitted area on the main unit cover.
*Be sure to check the operation.
Fix the cord at the power cord stopper at one
point with the supplied screw.
*Use the Phillips‑head screwdriver.
If the shaft is fixed in an inclined position at
process step, the pipe cover may not
install correctly . If this is the case, adjust the
fixing position of the shaft.
【Specification w/o Fan 】
6

Operating mode
selection buttons
Start/stop button
Checking of Operations
After confirming the above, the installation is completed.
①Check the initial status
・Confirm that all lamps illuminate for one second after turning on the power switch.
Then only the operating mode lamps (4 lamps) will blink.
③Check the operation of fan（only for specification with fan ）
・While doing the check No. (ring is rotating), press the FAN button once.
*After pressing the FAN button, fan starts rotating and the lamp of the FAN button illuminates.
②Check the operation
・Press the MANUAL button.
Press Start/Stop button.
Confirm that the ring rotates and heater works properly.
Pilot lamp (blue) blinks.
＜*CAUTION ＞
Heater starts glowing after the ring rotates approx. 360 degrees.
Fan button
(only for the specification with fan)
【Process】
【Control Panel 】