Takara Belmont YUME-iXi User manual

Version 5 May 2021
Contents
Before installation
Usage conditions
Content of packaging
Carrying the main body
After installation
Dimensions
Unit fixing position and plumbing layout
MEMO
1.Installation of Basin Unit
2.Piping
3.Installing the Step
4.Attaching the Seat Part
5.Procedure for swapping the reclining
pedal from left to right.
6.Attaching the External Covers
To the installer
• The instructions should be thoroughly read
and understood before installation to ensure
that YUME-iXi is installed correctly.
• After installation, give these instructions to the customer.
To the customers
• Customers must ask professional to install YUME - iXi.
• Customers must not install YUME
- iXi by themselves.
• Customers must store these instructions in
a safe place so as not to lose them.
* The actual shape of
YUME-iXi and the images and
dimensions listed in these instructions may be modified
and are subject to change without notice.
Caution
 The precautions listed here are to ensure that YUME-iXi can be installed safely, and to prevent any danger or risk to the person installing
YUME-iXi or those around them.All of these precautions are important for safety. Takara Belmont is not responsible for any damage or risk
to the person installing YUME-iXi or those around them due to accidents if YUME-iXi is installed without adhering to the precautions.
If YUME-iXi is installed after ignoring this symbol,
"there is the risk of light or moderate injury or physical damage".
Note : Plumbing should be performed by a qualified technician and should meet all national and local plumbing codes and ordinances.
It is the responsibility of purchaser and/or plumber to conform to national and local codes and ordinances.
Takara Belmont does not take any responsibility or liability for plumbing and installation.
″YUME
-
iXi″Installation Instruction
1
■YUME-iXi
Image is of
AY-YMIXIHGL*US
( )
7
8
10
12
13
14
AY-YMIXILGL1US YUME-iXi ／Ltype／GL1（WHITE）
GL2 YUME-iXi ／Ltype／GL2（BLACK）
GL3 YUME-iXi ／Ltype／GL3（DARK BROWN）
GL4 YUME-iXi ／Ltype／GL4（MAROON）
AY-YMIXIHGL1US YUME-iXi ／Htype／GL1（WHITE）
GL2 YUME-iXi ／Htype／GL2（BLACK）
GL3 YUME-iXi ／Htype／GL3（DARK BROWN）
GL4 YUME-iXi ／Htype／GL4（MAROON）
2
3
4
5
15
16
17
18

■Request measures to prevent water leakage under the floor and downstairs
Use waterproof flooring materials.
If the floor has an opening, cover the opening when completing the interior finishing (waterproofing).
Install all pipe packings.
Before installation
Installation of pipes
The following are important points to adhere during the installation of pipes.
Read through the details carefully and ensure that the pipes are installed correctly.
When installing this product, ensure that installation of pipes adheres to the instructions. Installing pipes without reading
through the precautions will mean water may not mix properly, and a set temperature will not be achieved.
This product is designed for indoor installation. Always install this product indoors.
Precautions during installation of pipes
Water supply pipe
● The installation should be performed in conformity with the laws and regulations of the area where the product is to be installed.
Do not use pipes made of materials that may introduce rust for the water supply pipe.
In general, VP pipes or other materials specified by regulations in that particular region, are recommended for installation.
Ensure to install 3/8"pipes for water and hot water supply pipes and 1-1/2"pipes for drain pipes.
Always use a reamer to deburr the ends of cut pipes.
Avoid using inverted U-shaped pipes (siphon) as these can cause air to become trapped.
Always connect hot water pipes and water supply pipes after removing all contaminants such as dirt, sand and oil as these can
cause problems.
After connecting the pipes and testing water flow, clean the filter and shower head.
The slope of the water service pipe should be determined in conformity with the laws and regulations of the area where the
product is to be installed.
Ensure that the drain pipe is installed at a gradient of 1/4" for a diameter of φ3.0" or less, or 1/8" for a diameter of φ3.0" or more.
Do not connect the hot water pipes and water supply pipes in reverse.
Connecting pipes in reverse will mean the temperature of water cannot be controlled properly by the water taps, which can
cause problems including burns.
Ensure that the hot water pipes from water boilers are only run over a short distance so as to minimize resistance.
Longer pipes can cause fluctuations in temperature and poor hot water delivery.
Always wrap pipes with lagging material after installation is complete.
Water boiler pipes
● In general, the same diameter and same pressure is recommended for main hot water pipes and main water supply pipes.
● Ask professional to install water boiler.
Avoid the anchor positions when installing the pipe risers.
Equipment comes with hair catchers installed.
Be sure to take the necessary precautions to prepare for and prevent possible water leaks.
2

Wooden floor
Mortar floor Mortar thickness of 2" or more
Special floor (stone finish)
A foundation with levels of strength listed above around the installation areas is required.
Plywood thickness of 1-1/2" or more (two sheets joined together)
If the floor surface is tiled, cracks may occur when fastening the bolts during installation of the YUME-iXi main body.
If this looks likely to happen, use the main body attachment diagram and template as a reference and change the material of the
attachment area that is in contact with the floor to another such as plywood or mortar.
The following levels of strength are required for the floor surface.
Hot water / water supply
Drainage
Rc 1/2" ; pipe risers from floor; rise dimensions : hot water 3"; water 3"
1-1/2" ; pipe risers from floor; rise dimensions : 3"
Usage conditions
Hot water supply and water supply conditions
Water used
Hot water supply,
water supply pressure
Hot water temperature
into the product
Water boiler
Public water supply (do not use non-drinkable well water or water that contains rust or sand.)
If the water hardness is 80 ppm or highe r, install a water softener to prevent the buildup of scale
within the basin body. Aeration may be minimal when using shampoo even if drinkable well
water is used, so a water softener should be installed.
Use a pressure between 14.5 and 58.0 psi . If multiple YUME-iXi are used,
ensure that the pressure does not drop delow 14.5 psi.
Set the water supply pressure ≧hot water supply pressure.
Set the di fference between the hot water supply pressure and water supply pressure to within
29.0 psi.
Do not use steam with the hot water supply .
Floor surface
Ensure that the material or finishing of the floor surface is waterproof or has a waterproof coating applied.
Always ensure that the floor surface is horizontally level.
Ensure that the floor surface is smooth and free from bumps around the attachment areas.
Pipe risers
3
[L type／H type]
If the floor surface is ceramic tile, marble, cultured marble, mirror-finish stainless steel, or another smooth, flat material, then when
the customer sits down, the step may not grip the floor and malfunction, and could lead to falls or other problems. If such floor
surfaces are used, do not use the step as is. Ensure that the "Floor sheet" (material: EVA resin) (sold separately) is used.
Set the hot water temperature to 176℉or less.
Set the temperature 50℉or higher than the shower temperature used.



□Basin Unit
Basin Unit
Content of packaging
4
□Neck cushion
□Drain cap □Hair catcher
□Pipe packing
M4×10: Truss-head screw（black）…6
M5 : Urea cosmetic nuts …2
M6×15: Truss-head screw …2
M6×35: Truss-head screw …2
□Screw Set for Cover
□Step
□Step (low)
[Ｈtype]
[Ｌtype]
□Maintenance Cover（small）
□Base cover□Trap cover
□Head pillow
…2
□Mohair tape
□Maintenance Cover
□Installation instructions…1
□Operating Manual…1
□Paper template…1
□YUME SPA Technical Manual…1
□Operation Instruction Manual for Mohair tape …1
Seat part
□Screen sheet □Back support cushion
Cover part
（※Spare parts.）
□Sponge
□Chair side carriage jig□Basin side carriage jig
[Option]

5
Do not remove
Caution
・I nstall it in the skid until the basin unit is built. There is a fear that
the product is turned over.
・Always have at least two people to carry the main body and hold
the basin when remove the bolt.Otherwise the basin is likely to fall.
〇While supporting the basin with hands, remove the hexagonal
head bolts (phillips head)(M8 x 50mm) from the unit base
(four locations).
Detach the basin unit from the skid.
■Carrying the Basin Unit
1
Carrying the main body
③Attach the carriage jig to the seat frame with bolts
(2 locations)
2Attach the carriage jig [Option].
Chair side carriage jig
①
Velcro
Seat（legrest)
Velcro
②
Bottom protection mat
＜Chair side carriage jig＞
①Turn over the legrest of the seat. ② Remove the front of the bottom protection mat from
the seat frame to see the screw holes.
Seat frame
Screw holes
(2 locations)

Caution
〇When carrying the basin unit, be sure to hold it by
the carriage jig. Do not hold it by the mixer pipe located
at the side of the basin.
Precaution for carrying the basin unit
① Temporarily remove the bolt on the right side of the
carriage jig.
② Insert the bolt for the left side of the carriage jig into
the position alignment hole.
③ Attach the right side of the carriage jig to the frame
using the removed bolt.
• Since the basin unit tends to tumble, be sure to carry the basin while maintaining balance.
• Do not carry the basin unit with the seat parts on it.
• Never hold the unit at the basin (ceramic). Failure to follow this instructions may result in breakage of
the basin.
• Do not hold the main body cover. Doing so may cause damage to the main body cover.
• Take care when handling the basin as it is heavy and fragile.
• Do not drag the unit. The foot part of the basin is made of steel, so dragging it may damage the floor surface or crack
the basin itself.
• The basin may become damaged if scratched by metallic objects such as watches or belts.
Remove all metallic objects such as watches when carrying the basin.
• Take extra care to ensure not to damage the covers.
• Do not touch the basin body pipes. Doing so may cause water leaks.
• The basin is unstable when it is not fixed to the floor.
※When carrying on stairs,please hold it at the lower handle.
6
3
Basin side carriage jig Left side position alignment hole
Right side of the
carriage jig
Left side of the
carriage jig
Basin
Lower handle
＜Basin side carriage jig＞
Carriage jig
Carriage jig

Installation of Basin Unit
1
(1) Set the dedicated paper template on the floor, and align it with the
water, hot water, and drainage pipe risers.
(2) Mark the bolt anchor position of the basin unit.
(3) Drill holes at the bolt anchor position of the basin unit.
(4) Remove the paper template.
Align the basin unit with the marked positions on the floor and anchor the unit with the bolts (6 locations).
3Fixing the Basin Unit on the Floor
1Marking the bolt anchor points
(1) Drill open a hole of the
specified diameter and
depth.
(2) Remove the dust from each
anchor hole by cleaning
with a vacuum cleane r.
(3) Insert the anchor bolt and
tap it with a hammer until
the center pin makes
contact with the bolt head.
(4)Adjust the fastening
strength of the nut
using a wrench.
Floor
Supplied
template
8.5 mm
Hole depth
2.0″ormore
Nut
Flat washer
Center pin
0.1
0.2″
~
Bolts to be used (supplied with the shampoo unit):
Plywood Floor
Hexagonal head tapping bolt + flat washer
(8 mm x 65)
Concrete Floor
Anchor bolt + plain washer
(M8 x 70, Pilot drill hole 8.5 mm(0.33″）)
(Use the wrench with the opposite side distance of 1/2″.)
Be sure to use a plain washer when securing the bolt.
■Request measures to prevent water leakage under the floor and downstairs
Be sure to take the necessary precautions to prepare for and prevent
possible water leaks.
• Use waterproof flooring materials.
• If the floor has an opening, cover the opening when completing
the interior finishing (waterproofing).
• Install all pipe packings.
2 Attach pipe packing
(1) Cut a slit in the pipe packing to suit the position of the pipes to be installed.
(2) Peel away the sheet from the adhesive surface of the pipe
packing and stick to the floor surface.
(3) Cut out a circle around the slit cut in the pipe packing to suit the
pipe surface, and fill in any gaps with caulking materials.
Caution
• Always attach pipe packing and apply caulking materials to the areas around
the pipes so that there are no gaps, in order to prevent condensation within
YUME -iXi or water seeping on the floor in the event of water leaks.
• If pipe packing is not used, condensation may cause water to pool on the
floor, structural parts may start degrading and malfunctions may occur.
Installation process for anchor bolts
Caution Caution
The strength of the anchor bolts will be reduced
if they are hammered into the hole while touching
the bottom. Open up a gap.
7
Pipe packing
(sponge)
Cut a slit
※Attach pipe
packing
※Apply caulking materials
to any gaps
Water Supply Pipe
Hot Water
Supply Pipe
Drain Pipe
ＹＵＭＥ-iXi Paper Template
Paper Template

Piping
２
8
１、Attach drain hose to a hairtrap and installed drain pipe.
Drain hose pass through in the hole of sheet metal parts.
２、Installing the Flexible Pipe
Hot water lineWater line
1/2” female screw
Turn valve
[Not included]
Flexible pipe
[Not included]
Caution
[Before piping installation]
“Hair trap” ,“Drain hose”,“Turn valve” and “Flexible pipe” is not included.
Prepare those parts that suited the local statute.
Drain pipe of unit side
The hole of sheet metal parts
Installed drain pipe
Drain hose
[Included parts]
[Not included]
Follow a local rule, when you attach piping.

●
Remove and clean any dirt trapped within the sprinkling filter unit.
Sprinkling filter unit
Shower head main unit
Gasket
Foaming water outlet O-ring
After the hot water becomes clear during the water flow test, always clean the sprinkling filter unit.
Failure to do so can result in insufficient flow rate.
Cleaning
3Test water flow
Caution
Always test the water flow to prevent
accidents during use.
* Test the water flow and inspect the following
items. The hot water may be slightly tainted
at the start of the water flow test,however this
does not indicate any problem.
9
(1) Is there no water leaking from the pipe joints?
The pipe joints may come loose during transportation,
so check the joints within the bowl thoroughly.
(2) Are the hot water supply and water supply pressures
at the same, stable pressure?
(3) Can temperature be controlled properly?
(4) Check that the shower outlet flow is sufficient.

10
3
1
④Slide out step .
⑤Attach the two locations on the bottom of the step slide
rail to the basin unit using truss-head screws.
(M6 x 35, 2 screws)
① Check that the step shim is attached with tape to the
bottom of the slide rail.
If the step is installed while it is slided out, this could
lead to the step rattling, poor sliding operation, and noise.
Ensure the step is installed while fully retracted.
Caution
③ Attach the two locations on the top of the step slide rail
to the basin unit using truss-head screws.
(M6 x 15, 2 screws)
※Assemble while the step is retracted.（packing state ）
Tighten the screws while pushing down on the upper
surface of the slide rail.
※Assemble while fully retracted.
Slide rail upper surface
Tighten the screws while pushing
down on the upper surface of the
slide rail.
truss-head screws
(M6×15）
truss-head screws
(M6×35）
②Remove the screws fixing the legrest.
(M6 x 15, 2 screws)
2 locations
Slide rail
Step
Step shim
Installing the Step
Install the step to the basin unit.
legrest

11
⑥Leave the slide rail temporarily attached by loosening the truss-head screws on the top of the step slide rail.
(M6 x 15mm, 2 screws)
⑦Temporarily attach the bottom of the step slide rail to the basin unit with the truss-head screws.
(M6 x 35mm, 2 screws).
⑧Fully retract the step.
Fully retract the step by tilting up the step while lifting the slide rail.
・When retracting the step, the step shim may catch, and may not go fully in.Check that the step is fully against the stopper.
・When sliding the step, dragging the adjuster without lifting up the step may result in damage to the floor surface.When
sliding the step, ensure it is lifted up and that the casters are used.
・If the step is installed while it is slided out, this could lead to the step rattling, poor sliding operation, and noise.
Ensure the step is installed while fully retracted.
⑨Fully tighten the truss-head screws temporarily attached in ⑥.
When tightening the screws, do so while pushing down on the upper surface of the slide rail.
⑫Remove the step shim.
Lift up step
Lift up the slide rail.
※If, in the procedure on the previous page, the bottom screw positions do not align, use the procedure below.
Step
Slide rail
⑩Slide out the step.
⑪Fully tighten the truss-head screws temporarily attached in⑦.
(M6 x 35mm 2 screws)
Caution
Caution
The step shim is a fixture used when installing the step.After use, ensure that the step shim is removed and stored with this
manual.If the step shim is lost, then re-installing the step after it has been removed for repairs or the like may not be possible.

12
4
2
1Attach the screen sheet to the base side cover.
3
Attach the leg rest using hexagonal head bolts.
(M6 x 15mm, 2 bolts)
Velcro
Back support cusion
Velcro
Screen sheet
3
Attaching the Seat Part
Attach the legrest.
Attach the edge of seat to the legrest by velcro.
4Place the back support cusion on the seat.
2 locations
Legrest

5
3
2
1
4
5
3
13
<Left side>
：Temporarily attach the 2 truss-head screws.
：Slide the reclining pedal in.
：Fix using the third truss-head screw.
：Firmly tighten the temporarily attached screws.
2
3
<Right side>
Swap the reclining pedal and the base cover attachment fitting from left to right.
Remove the reclining pedal and the base cover
attachment.
【Reclining pedal：Truss-head screws M5 x 12mm (Black) , 3screws】
【Base cover attachment：Hexagonal head bolt M5 x 14mm, 3screws】
【Base cover：Truss-head screws M4 x 10mm (Black) , 6screws】
Remove the maintenance cover and the base cover.
Maintenance cover Base cover
Check that pressing the reclining pedal
with your foot reclines the backrest, and
lifting your foot off the reclining pedal
fixes the backrest in place.
Attach the base cover and maintenance
cover.
×3 ×3
×3 ×3
-3
3-1
3-4
3-2
3-1
3
3
3-4
-3
-2
Procedure for swapping the reclining pedal from left to right.
This product has a reclining pedal on its left side.
Depending on the salon layout, if it is necessary to install the reclining pedal on the
right side, then swap the position of the reclining pedal from left to right in accordance
with this manual.
Reclining pedal
Reclining pedal Base cover attachment

14
6
3
2
1
1
2
3
Attaching the External Covers
Attach the trap cover to the basin unit.
The trap cover is fitted into the screw section at the bottom
of the cover bracket under the basin, and can be attached
using urea cosmetic nuts in 2 locations.
① Place the trap cover edge tabs on the edge of the frame
cover.
② Insert the trap cover as if rotating it into place with
the tabs in ①as a fulcrum while pushing both edges
inwards.
③ Position the screw sections so they pass through the trap
cover attachment holes, and when the screws emerge
from below, fix with urea cosmetic nuts.
Push inwards
Push inwards
Trap cover
Base cover
The maintenance cover can be attached using magnets
in 2 locations.
①Insert the tab at the bottom of the maintenance cover
into the base cover.
②Attach the maintenance cover as if rotating it into place.
Maintenance cover
①
①
②
②
②
③
①
②
Attach the base cover to the base using
truss-head screws.
(M4 x 10, black, 6screws)
Attach the maintenance cover.

After installation
Caution Be sure to execute the inspection without fail to prevent accidents during operation.
●Inspection
Inspect the following items.
(1) Check that there are no missing screws or other parts.
(2) Check that there are no loose parts on the shampoo unit or the chair. If any part of the shampoo unit or the chair is
loose, check the bolts at the joints again.
(3) Check that there are no cracks or contamination on the basin.
(4) Check that there are no problems, such as flaws on the external appearance.
(5) Check that there are no water leaks on the floor.
(1) Set the neck cushion to the metal fittings in the
direction as shown in the image.
(3) Adjust the shape of the neck cushion to suit the metal fittings,
and attach the basin side snap buttons of the neck cushion to the
fastening pins.
Insert the head pillow in the direction as shown in the image.
(2) Attach the seat side snap buttons of the neck cushion to the
fastening pins on the metal fittings.
The fastening pins can be removed.
Take care not to lose the fastening pins.
15
●Attach neck cushion
●Attach head pillow
Neck cushion
Snap
button Basin side
Seat side
The short edge
faces basin side
The long edge
faces seat side
Metal fittings
Fastening pin Snap button
Snap button
Head pillow
(underside)
Attachment fitting

Dimensions
16
H :
30
L :
27
75°
Movable range
33°
64-5/8
26
20
2
8-5/8
1
63-5/8
Recomended min：
clearance of 24″
Min:3-1/8
18-7/8
53-1/8
37
24-3/8
73-2/8
End of chair
（1 - 1/2"）
【Recomended】
20″or over
33
Recommended min.spase of 99 (min:93-1/8) for standing position)
（Min: 8″ for standing position)
★
when chair is in use, the
space behind it cannot
be entered.
passage
(For 20″passage)
Center of Drain Pipe
Wall surface or furniture End of basin
Hot water supply
position
Water supply
position
Drain position
Wall surface
or furniture
Wall surface
or furniture
Step
front/back slide
★Figures shown above are for seating a customer about 170cm in height. When attending a taller customer, please
allow sufficient leeway. Basin and seat dimensions may vary from product to product.
10-5/813-3/8 20-1/2
Bolt Anchor Point ×6
H :
23-3/8
L :
20-1/4
H :
10-5/8
L :
7-7/16
H :
6-1/8
L :
3
3
H :
19-5/8
L :
18-7/16
H :
36-5/8
L :
33-1/2
H :
34-1/4
L :
31-1/8
■Top View
■Side View
Outline drawing (Unit :inch)
H:When operated from standing position
L :When operated from seated position
3-1/2
2
13-3/16
【Height of basin】
3

Unit fixing position and plumbing layout
17
Outline drawing (Unit : inch)
Drainage Center
Product Center
Basin Side
【ProceduresforInstallingthePipeGasket】
①Make a cut in the pipe gasket at the pipe riser point. ②Peel off the adhesive sheet on the pipe gasket and set the gas ket on the floor. ③Cut the gasket in a circle at the cut portion on the gasket al ong with the pipe, and then caulk the area around the pipe.
Be sure to take the necessary precautions to prepare for and prevent possible water leaks. ●Use waterproof flooring materials. ●If the floor has an opening, cover the opening when
completing the interior finishing (waterproofing).
●Install all pipe gaskets.
The floor surface requires the following strength: - Wooden floor : Veneer board with 1-1/2” thickness or more - Mortar floor : Mortar thickness of 2” or more - Special floor (stone, etc.) : The base for which the above-stated strength is ensured should be formed in the installation are a.
Floor Surface of Tile or Glass Finish The tiles or glass of the floor surface will break when the bolts are embedded during installation of the shampoo unit. If this is the case, the installation area should be finished with materials such as plywood or mortar. ①Peel off the inner tiles or glass along the outside lines of the installation area of the floor. The work must be done carefully; otherwise, the peeled portion may be obvious. ②Place composite panels in the peeled-off area. The panel surface should be higher than the surrounding tile or glass surface (within 1/16” or 1/8”).
：Show the floor installation surface.
CautionforAnchorBoltInstallation
Anchor bolts should be installed so that the screws will protrude from the bolt head by 3 to 5 mm. If the protrusion exceeds 5 mm, the bolt head may interfere with the cover.
2～5㎜
2
2
(14-1/8)
10-5/8
16-7/16
13-3/8
6 - 5/8
7
- 3/8
13 - 1/4
14 - 3/4
Φ2
10-5/8
13 1/8
12 - 7/16
Bolt Anchor Point
Bolt Anchor Point
Bolt Anchor Point
Bolt Anchor Point Bolt Anchor Point
Bolt Anchor Point
Exterior Line of Cover
①Set the dedicated paper template on the floor by aligning it w ith the rise points for the water, hot water, and drainage pipes. ②Mark the bolt anchor position of the basin main unit. ③Drill holes at the bolt anchor position of the basin main unit . ④Remove the paper template.
Request measures to prevent water leakage under the floor and downstairs
Pipe Gasket (Sponge Side)
Make a cut. ※Install the pipe
※Be sure to caulk the pipe.
CAUTION
DO NOT install riser piping where bolts or anchors are used for fastening.
Recommended minimum distance between drainage center and wall (furniture, etc.) is 61 (min : 55 for standing position)
＊When chair in use, the space behaind it cannot be entered.
H:When operated from standing position
L :When operated from seated position
Rise : Rise :
Hot Water Supply (3/8”)
H type
L type
3”
3”
Water Supply (3/8”)
H type
L type Rise : 3”
Rise :3”
Recommended minimum distance between product center and wall
(furniture, etc.) is 33(applicable when passage is 20 wide)
3”
Drainage (1-1/2”)
Rise : 3” Rise :
Htype
Ltype
3-1/2
（1-1/2）

ＭＥＭＯ
18

ＭＥＭＯ
19

20
NOTE
1E043YA0
1-1, 2-Chome, Higashi-shinsaibashi,Chuo-ku,Osaka,Japan
101 Belmont Drive. Somerset,NJ 08873
800-526-3847
TAKARA BELMONT CORPORATION
Book Number
U.S.A
JAPAN