Takara Belmont Yume DX User manual

SHAMPOO UNIT
YUME DX
This manual provides information and instructions for YUME DX
SHAMPOO UNIT. The instructions contained in this booklet should be
thoroughlyreadandunderstoodbeforeattemptingtoinstalltheequipment.
After the installation is completed, le this manual and refer back to it
for future maintenance.
IMPORT ANT
INSTALLATION
INSTRUCTIONS
1E002DC0Version4
2018.07

TAB L E OF C ONT E NT S
INSTAL L AT ION INSTR UCTIONS
1. Overall View and Major Components .......... 1
2. Dimension & Specifications ......................... 2
3. Plumbing L ayout........................................... 3
4. Contents of Unpacked Products.................... 4
5. Installation Instruction.................................. 6
5-1. Preparations for Installations
...................... 6
5-2. Installation of the Carriage Jig
.................... 6
5-3. Marking for unit fixing position
.................. 7
5-4. Fix the Moistureproof sheet and packing
.... 7
5-5. Installation of unit
.......................................... 7
5-6. Drain Pipe Connection ........................................................................
....................................
9
5-7.
Water and Hot Water Supply L ine Connection .... 9
5-8A. R emove the fixing bolt .................................
5-8B . Unit Power Supply L ine................................ 11
5-9. I nstallation of B ase Cover................................ 11
5-10. Mount the seat cushion ................................. 12
5-1
Fix the backrest cover
1. Fix the seat cover .......................................... 12
5-12. Attach the backrest ........................................ 13
5-13. Wiring Connection ........................................13
5-14.
5-15. Attach the Neck Cushion ...............................
14
15
5-16. Attach the Head Pillow ................................. 15
10

1. Overall View and Major C omponents
-1-
B ackres t
Headrest
S hower head
S hampoo basin
S eat
Legrest
Legrest lever
Main power switch
S ervice outlet
Maintenance cover
Headrest handle
Headrest bar socket
Neck cushion
(C ons umable)
Head pillow
(C ons umable)
Temperature control knob
S hower head
S hower hose
Tap
F loor s heet
■F oot S witch
E X-Y M2NLA : Left side foot switch E X-Y M2NR A : R ight side foot switch ■Leg-rest Lever
UP DOWN
(E X -Y M2NLA and
E X -Y M2NR A only)
UP
DOW N
UP
DOW N
P res et S hampoo position
B ackres t return
P res et S hampoo position B ackres t return
B ackres t
reclining
B ackres t
raising
Auto R eturn S eat rotation lock Auto R eturn S eat rotation lock
B ackres t
reclining B ackres t
raising
■Main B ody
A sticker of drain hose replacement
Hose replacement (1 )
Service History
Month Year
Month Year
Month Year
Month YearHose replacement (3 )
Hose replacement (2 )
ST
ND
RD
Original Installation date
Drain cap

2. Dimension & S pecifications
-2-
Type ------------------------------ EX -Y M2NL , EX-Y M2NR, SU-Y M2
Drive System -------------------- Motorized Hydraulic System
Measurement -------------------- 760 x 2000 x 990 mm (W x L x H)
A ngle of B ackrest ---------------- 67° (8° 75°)
Type of Mixing ------------------ Thermo Mixing
Stop Valve ------------------------ Water x 1 (Handle Type) / Hot Water x 1 (Handle Type)
E lectrical R equirements -------- 230V 50Hz 1.7A
Usage E nvironment ------------ Operational Temperature (10 40°C)
Water and Hot Water ---------- 0.08 0.6Mpa (0.8 6kgf/ )
Supply Pressure ---------------- Water Supply Pressure Hot Water Supply Pressure
Pressure difference between water supply and hot water supply within 0.2Mpa (2kgf/. )
Water Volume (Shower Head) ---- 10L /min (water and hot water pressure are 0.1 Mpa)
Weight --------------------------- 205 kg
650
520
520
2000
760
845
505
610
950
990
8°
≧
cm2
～
～
～～
cm2
E lectrical R equirements -------- 230V 50Hz 1.7A (appliance itself)(CE Spec,)

3. Plumbing Layout
-3-
Connected position of
power plug and
power supply outlet
From wall or Cabinet
Min.1100mm
From wall or Cabinet
Min.1900mm
Edge of Base Plate
Center to wall or Center to Cabinet
Min.1400mm : Headrest side
(When seat rotates 90°degrees)
Min/1300mm : Legrest side
Bolt(anchor)
fixed position
Bolt(anchor)
fixed pos ition
Bolt(anchor)
fixed position
Bolt(anchor)
fixed position
200(Moisturepro of Packing)
15
160(Space of Plumbing)
32 5
143
Drain VU40
(Height 60mm)
Water1/2”13m/m(Height 50mm)
Hot water1/2”13m/m
(Height 50mm)
200(Space of Plumbing)
480(Base Plate)
430
215
195
20
95
265(Moistureproof packing)
80
75
28 34
115
50 15 160
135
105215
300
815(Base plate)
75
65
Seat side Bowl side
Power Source
(Cable should have 1000mm)
100
455
420
210
(When seat rotates 90°degrees)

M8×70 Anchor Bolt x4
M8×65 Hex Head Tap Bolt x4
Flat Washer ×4
4. Contents of Unpacked Product
●YUME DX Main Body ●Carriage Jig
-4-
Elbow and drain pipe(VU40) are NOT INCLUDED with shipment. Please prepare it beforehand.
Neck Cushion Head Pillow Drain Cap Hair Catcher
Floor Bolts Moistureproof
Sheet Moistureproof Packing (Sponge)
Water Stop
Valve Flexible Pipe Drain Hose Packing Drain Hose Clamp
Noise Reduction Tape
Anti-water dropping device Operation Manual
Installation instructions
YUME SPA Technical Manual(except for China)
• Jig A
• Jig B Bracket
• Jig B
• Jig B Support Bar
Screws

œSeat and Backrest set
-5-
＜SU-YM2A/SU-YM2AM＞
＜SU-YM2B/SU-YM2BM＞
・S eat ・B ackres t ・S eat C over (L)
・Legrest C over
・B ackres t C over
・S crew set
for backrest cover ・
S hort-circuit C onnect
or
(S U-Y M2A only)
・Headrest
(S U-Y M2AM only)
・S eat C over (R )
・S eat ・B ackres t ・S eat C over (L)
・B ackres t C over ・S crew set
for backrest cover
・S hort circuit C onnect
or
(S U-Y M2B only)
・Headrest
(S U Y M2B M only)
・S eat C over (R )
・Legrest fixing screw s et

-6-
5. Installation Instruction
1. Unpacking
R emove nails from lower part of wooden crate.
L ift up the upper portion of wooden crate.
Chair will be left on the skid.
2. R emove the pump cover
1. R emove the screws and take out the maintenance cover,
base cover left and right from the main body.
2. R emove the oil plug with red tag from oil reservoir.
3. Plug the unit power cable into the
suitable power supply outlet.
4. Turn on the main switch located on the left side
of the base.
5. K eep depressing UP button of foot switch
until the seat is raised to the end.
6. Turn off the main switch
7. Unplug the unit power cable from the power supply outlet.
5-1. Preparations for Installations
Nails
Nails
Oil P lug with R ed T ag
Maintena nce C over
B as e C over(R )
B as e C over(R )
Oil R es ervoir
Main S witch
F oot S witch
Note : Do not remove the unit from the pallet
until the unit fixing position is ready.
Holding the Carriage Jig and place it at
planned location. Do not carry by holding
the body or basin.
5-2. Installation of the Carriage Jig
1. Fix the Jig A to the base.(M10 x 30)
2. Fix the Jig B bracket to the base.(M10 x 50)
3. A ttach the Jig B support bar to the
Jig B bracket.
4. A ttach the Jig B to the Jig B support bar
and tighten the nuts.(M16)
CAUT ION
Do not turn on power during installation.
B as e
1 J ig A
2 J ig B B racket
4 J ig B
3 J ig B S upport B ar
S crews
M10 x 30
S crews
M10 x 50

Moistureproof Sheet
Moistureproof
Packing
Moistureproof Packing
Seal a space
around here
5-4. Fix the Moistureproof sheet and packing
Please obtain the moistureproof sheet and the moistureproof packing to prevent from the
main body damaged by the moisture. Deterioration and the breakdown of structural parts
and electrical equipments might not be occurred without the installation.
1. Fix the moistureproof sheet on the floor.
Plywood Floor : Wood Screw
Concrete Floor : Glue
2. Make a cut in the moistureproof packing according to piping position.
3. Peeled off the sheet on the adhesive face side of the moistureproof packing. Passes under the
piping and electric code on the moistureproof packing and attach to the floor.
4. Seal a space around the piping and electric code.
5-5. Installation of unit
1. Remove the four tapping screw(M8 x 60mm) fixing the
unit base plate to the pallet.
5-3. Marking for unit fixing position
Use supplied full scale template to mark the
fixing position on the floor. Check the piping
and power outlet position before marking.
1. Put the supplied templete on the floor and hold with
the tape etc. It should be set to the position of
piping and power outlet.
2. The chair fixing position is marked on the floor.
3. Make it holes for marked position. (8.5 mm x 50 mm )
4. Remove the template from the floor.
Base
Tapping Screw(M8 x 60)
Pallet
-7-
Marking
Hot water supply pipe
Water supply pipe
Drain pipe
Power cable
Power supply outlet
DX

-8-
Templete
8.5 mm
50mm
or more deep
F loor
2~ 5mm
C AUTION
B as e P late
Hammer
F lat Was her
Nut
C enter pin
If the anchor bolt is tapped with its and contacting the bottom
of the hole, the strength will be lowered. P roper clearance
must exist between the end of the anchor bolt and the bottom
of the hole.
Do not make scratch or damage the floor while moving the
unit. Please use the carriage jig to move it.
4. Fix the main unit with the four screws.
Plywood Floor : Hex head tapping screw M8 x 65
Concrete Floor : Anchor bolts M8 x 70
5. When the moistureproof packing is bigger than
main unit base, please cut it out.
Construction process of anchor bolts.
1.Drill the anchor holes
of a specific diameter
and depth.
2.Clean each anchor hole
thoroughly using a
vacuum cleaner, with a
narrow nozzle attachment
to reach into the hole and
remove all debris.
3.Insert the anchor bolt, tapping
it lightly with a hammer to seat
it. Position the material, and
then drive the center pin into
the anchor unit it is snug.
4.Adjust the fastening strength
of the nut using a wrench etc.
Hold the Jig A and B to lift the unit by
2 workers to move it. Otherwise, breakage
may result in.
CAUT ION
2. Hold the carriage jig and move the main unit to
marked position on the floor.
3. Decide the installation position and remove the
carriage jig A and B from main unit base.