Takstar E190M User manual

欢迎使用 TAKSTAR 便携式多媒体扩音器。本产品是专为教学、导游和参观等
设计的，采用PO²数字功率合成技术，提供更长久的电池使用时间和更大输出功
率，是教学、导游的理想选择。在使用之前，请仔细阅读说明书，以便能正确的
操作，发挥本扩音器的理想性能。
产品特性
· 采用PO²数字功率合成技术，提供高达10W的音频功率输出
· 选用稀土材料扬声器，重量更轻、音质更好、声音更大
· 具有音乐播放功能，支持U盘、TF储存卡的多媒体音频文件播放
· LED高亮度数码显示屏，直观掌控播放状态
· 具有一键录音功能，可录制MIC语音及FM广播电台
· 支持FM广播接收，全自动搜索和保存电台
· 内置大容量锂电池，以及MCU充电管理系统，使用安全可靠，充电只需5小时，
使用时间可达8-12小时
· 产品符合人体工学原理设计，造型新颖，外观时尚，使用舒适
控制面板功能示意图
电源开关：向ON方向转动旋钮，听到“滴”一声，此时LED数码显示屏 显
示“Lod”，表示扩音器已通电并进入扩音状态。继续向左转动旋钮声音越大，
反之，声音越小直至关机
AUX IN 输入插孔：用 Ø3.5mm连接线，将DVD 、MP3等音乐信号导入本扩音
器中，做为有源音箱使用
MIC IN 输入插孔： 将头戴式麦克风插头插入此孔，进入扩音状态
上一曲按键 ：在MP3播放状态时，短按此键为上一曲，长按此键可快退当前
播放的曲目；在FM播放状态时，短按此键可选上一个频道，长按此键可半自动
搜台
播放/暂停按键 ：短按此键可控制MP3、FM、录音的播放与暂停。在MP3播
放时，长按此键可以快速读取录音文件；在FM播放时，长按此键进入全自动搜
台
下一曲按键 ：在MP3播放状态时，短按此键为下一曲，长按此键可快进当前
播放的曲目；在FM播放状态时，短按此键可选下一个频道，长按此键可半自动
搜台
音乐循环按键：按此键设定与取消当前音乐曲目的循环播放状态
功能切换按键：短按此键可切换MP3模式、FM模式及“Lod（扩音）”模式；
长按此键进入录音模式，重复操作可保存退出录音模式。
录音操作：在FM模式下长按此键可录制当前播放的FM内容；在MP3模式下长
按此键可录制MIC语音。（录音操作只能在FM或MP3模式下进行）
LED数码显示屏：可显示当前的工作状态及电池电量显示。当电池电量标识
“ ”闪烁时，表示电池低电压，此时应及时充电，以确保本机正常运作
电源适配器输入插孔：将DC 5V直流电源插入此孔进行充电
TF 卡插口：根据示意的插卡方向插入TF 内存卡，插入时，听到“嗒”一声，
表示已安装到位并将其锁住；取卡时只要将卡往下按，听到“嗒”一声，TF 内
存卡会自动弹出来
USB移动内存插孔：可支持大容量U盘
天线
肩挂扣
背扣：安装时，把背扣对准机壳的扣位方向按下，顺时针转动背扣，可以把背
扣固定在机壳上，反之，逆时针转动背扣即可取出
12
13
广东省电声工程技术研究开发中心
广东得胜电子有限公司制造
地址：广东省惠州市博罗县龙溪镇富康一路2号
电话： 400 6828 333 传真：[phone] 邮箱： 邮编：516121 网址：[e-mail]
E190M
15
11
12
14
13
适用场合
· 教学、导游、宣传、参观、晨练健身等场合扩音
标准配置
HM-700头戴麦克风
背扣
1. 将头戴麦克风正确的佩戴在头部，并调整好麦克风的拾音角度
2. 将Ø3.5mm的麦克风插头插入麦克风输入孔内
3. 打开电源，LED数码显示屏显示“Lod”时，调整音量到合适的音量大小
4. 使用过程中，若LED数码显示屏上的“ ”闪烁时，表示电池低电量，请及时充
电
使用说明
1. 请不要将外部的音源信号（如DVD、MP3等）从MIC插孔输入，以免声音幅度过
大而失真
2. 为了达到良好效果，请对准头戴麦克风的咪芯（1-2cm）处发音，以防方向不正
引起啸叫
3. 非专业技术人员请不要擅自拆机改装或维修；如有问题或服务需求请联系当地经
销商
4. 低电量或长时间不使用时应将电池充满电，以确保电池的使用寿命
5. 请勿将电池或电池组放在日照、火烤等类似过热环境中
6. 注意：电池或电池组更换不当会有爆炸危险，只能用同样类型或等效类型的电池
来更换并注意电池极性
7. 禁止：禁止电池反接，短路，猛烈撞击和作为儿童玩具；不能使用其他充电装置
为本机电池充电，也不能用本机为其他的电池充电，使用不当会有爆炸危险；禁
止对非充电电池充电
8. 整机及附件都应放置在室内干燥通风处，避免雨淋、水滴、进水、重摔及覆盖通
风孔
9. 为保护环境，请将废弃电池放入指定的分类垃圾桶或寄回给生产商，不可直接丢
弃
10. 应保持电源或充电适配器的操作方便。长时间不用时，请将适配器从电源插座中
拔出
11. 本产品适用海拔及气候条件由选配的适配器决定，适配器上图标代表含义如下：
注意事项
· 频率响应：80Hz-12kHz
· 额定输出功率：6W
· 峰值输出功率：10W
· 扬声器阻抗：4Ω
· 工作电压： 3.7V
· 电池规格：3.7V锂离子电池
· 充电器规格： DC5V 600-750mA
· 使用时间：8-12小时
· 充电时间：约5小时
· TF卡： 支持到16G
· 媒体格式：MP3、WAV、WMA
技术参数
肩带
14
15
DC 5V 150mA
DC 5V 600mA
扩音器 适配器（赠送）
说明书
仅适用于海拔2000
米以下地区使用
2000 m
仅适用于非热带
气候条件下使用
扩音器（数码播放器）

Features
Application
Content
Operating Instruction
Notice
Specification
Strap
1pc
E190M Amplifier
1pc
Headworn Microphone
1pc
Power Adapter
1pc (Ferr Part)
Buckle
1pc
User Manual
1pc
E190M
Guangdong Takstar Electronic Co.,Ltd.
Address: No.2 Fu Kang Yi Rd., Longxi Boluo Huizhou, Guangdong 516121 China
Tel: [phone] Fax: [phone] Email:[e-mail] Website: www.takstar.com
⑨
Control Panel Function Diagram
15
11
12
14
13
DC 5V 150mA
DC 5V 600mA
1. Do not input the external audio signal such as DVD, MP3 into the MIC socket to avoid the
sound distortion due to high volume
2. To achieve the best performance, please aim at the capsule of the headworn microphone
(1-2cm) to speak to avoid howling due to wrong direction
3. Non-professional technician is not allowed to disassemble and modify or repair the device.
Please contact your local agent if you need service or have any question
4. Please fully charge the battery to assure its service life if the device will not be used for a
long time or the battery voltage is low
5. Do not expose the battery or battery pack to extremely hot environment such as sunlight
or fire etc
6. Caution: improper replacement of battery or battery pack is likely to cause an explosion,
user can only use the same or equivalent type of battery to replace the original one and
should pay attention to the battery polarity
7. Warning: it's forbidden to connect the battery in reverse, to short circuit or hit the battery
violently, to use the battery as a child's toy. Do not use other charging equipment to charge
the battery of this device, do not use the device to charge other battery, improper use may
cause a risk of explosion. Do not charge a non-rechargeable battery
8. Put the device and its accessories in a dry and ventilated place, keep them from rain, water,
avoid falling down heavily and don't cover the ventilation hole
9. Put the used battery in a designated trash can or send it back to the manufacturer to
protect the environment
10. Keep the power adapter or charger handy, unplug it from the power socket if you are not
going to use it for a long time
11. The applicable altitude and climate condition of this product is subject to the power adaptor,
the meaning of the power adaptor icons is as below:
Welcome to use TAKSTAR portable multimedia amplifier. This product is
teaching, tour guiding, etc. It adopts PO² digital power synthetic technology for long battery
play time and maximum output power, it is an ideal choice for teaching and tour guiding.
Please read this user manual carefully before using to make sure the correct operation and
exert its best performance.
specially designed for
· PO²
· Rare earth material speaker features light weight, excellent sound quality and loud output
volume
∙ Music play function, supports the multimedia audio files play of USB disk and TF card
∙ High brightness digital LED display for controlling the working status intuitively
∙ Recording function controlled by one button, supports microphone and FM broadcasting
content recording
∙ Built-in FM function to search and save the radio stations automatically
∙ Built-in high capacity lithium-ion battery and MCU intelligent recharging management
system for secure recharge/discharge, 5 hours fast recharging time and long play time up
to 12 hours
∙ Unique and fashionable design
digital power synthetic technique, 10W output power
① Power Button: rotate the knob to the ON position until a “di” sound, the LED digital display
will indicate “LOD” , it means the amplifier is turned on and enter into the amplifying
status, continue rotating the knod to the left, the more, the louder. Conversely, the smaller
the sound is until it turns off
② AUX IN Input Socket: connect DVD / MP3 music signal with the Ø3.5mm connecting cable
to the amplifier, used as an active speaker
③ MIC IN Input Socket: plug the headset microphone into this port for amplifying
④ Previous Song Button : short press this button under MP3 play mode for the previous
song. Long press for fast backward the current playing song. Short press for the previous
channel under the FM broadcasting mode. Long press this button for automatic station
searching
⑤ Play/Pause Button : short press this button to control the MP3, FM, recording's play
and pause. Long press this button for fast playing the audio file under MP3 play mode;
when FM is broadcasted, long press this button for automatic station searching
⑥ Next Song Button : short press this button for the next song under MP3 play mode. Long
press for fast forward the current playing song. Short press for the next channel under the
FM broadcasting mode. Long press for semi-automatic station searching
⑦ Music Cycle Button: press this button to confirm or cancel the current music cycle play
mode
⑧ Function Switch Button: short press this button for MP3, FM or “Lod” (amplifying) mode
switchover. Long press this button to enter the recording mode, repeat the operation to
save the recording and exit recording mode. REC: long press this button to record the
current FM broadcasting content under FM mode. Long press this button for MIC voice
recording under MP3 mode. ( Recording function can only be operated under FM and
MP3 mode)
⑨ LED Display: display the current working status and the battery level. When the battery
sign is glittering, it means battery level is low and should be recharged in time to
ensure the amplifier is working properly
⑩ Power Input Socket: connect DC 5V power to this socket for recharging
⑪ TF Card Slot: slot a TF memory card according to the indicated direction, the card is fixed
properly and locked till a “da” sound. To take out the card, press down the card till a “da”
sound , the TF memory card will pop up automatically
⑫ USB Socket: support large capacity U disk
⑬ Antenna
⑭ Hanging Buckle
⑮ Hook: when installed, put the hook align with the housing buckle, press and clockwise
rotate the hook to fasten it on the housing. Conversely, counterclockwise rotate it to
unfasten
1.
2. Plug the Ø3.5mm microphone plug into the microphone input port
3. Turn on the amplifier, LED display shows “LOD” , adjust the volume to an appropriate level
4. If the “BAT” sign on the LED display glitters during use, it means the battery power is low,
please recharge in time
Wear the headset microphone on the head correctly, adjust the micro phone pickup angle
∙
∙ Rated Output Power: 6W
∙ Max. Output Power: 10W
∙ Output Impedance: 4Ω
∙ Operating Voltage: 3.7V
∙ Battery Specification: 3.7V lithium-ion battery
∙ Power Adaptor Specification: DC 5V 600-750mA
∙ Playtime: 8-12hrs
∙ Recharging Time: Approx. 5hrs
∙ USB/TF Card: Max.16G
∙ Media Format: MP3, WAV, WMA
Frequency Response: 80Hz-12kHz
Teaching, tour guiding, morning exercise. promotion
The device and its accessories can
only be used safely in the areas
below an altitude of 2000 meters
2000 m
The device and its accessories
can only be used safely in
non-tropical regions
Amplifier (Digital Player)