Takstar E126A User manual

扩音器
AMPLIFIER
E126A

前言
产品特性
○
○
○
○
○
○
○
○
一款体积小巧轻便的MINI型扩音器；
采用稀土材质扬声器，重量轻、音质好、声音大；
数字扩音技术，8W大功率音频输出；
内置大容量锂电池，节能环保，使用时间约15小时；
具有AUX音频信号输入功能，可充当小音箱使用；
配备指示灯显示设计，实时了解扩音器工作状态；
具有肩挂及腰挂等多种佩戴方式，使用更方便；
产品依照人体工学原理设计，造型新颖，外观时尚。
尊敬的用户：
感谢您选购得胜E126A扩音器，为了您能够更好的了解使用本产品，建议
在使用前仔细阅读本说明书。
若存在有疑问或者您有宝贵的建议，可通过拨打得胜官方服
务热线 400 6828 333 或微信扫描二维码关注得胜官方公众号与
我们联系。
扩音器
E126A
包装清单
腰带 1条
说明书 1份
1
Type-C充电线 1条
背扣 1个
头戴麦克风 1个
主机（扩音器） 1个

适用于教学、导游、培训、促销等场合扩音
频率响应：150Hz-12KHz
峰值功率：8W
扬声器阻抗：4Ω
总谐波失真：THD≤1% 1KHz@4R,4W
工作电压：3.45V-4.2V
电池类型：锂离子电池
电池容量：3.7V/1800mAh
• 充电方式：DC 5V 800mA
• 充电时间：约2.5小时
• 使用时间：约15小时
• 产品重量：约148g
• 产品尺寸：92mm*72.5mm*25mm
• 拾音器：背极式驻极体
• 指向性：单指向
• 频率响应：60Hz-16KHz
• 灵敏度：-48.5dB±3dB(0dB=1V/Pa，
at 1KHz)
注：以上数据由得胜实验室测得并拥有最终解释权!
适用范围
主机参数
技术参数
头戴麦克风参数
2
扩音器
E126A

①电源开关和音量调整旋钮：向“ON”方向拨动旋钮，听到“滴”一声，表示扩
音器已通电，此时电源指示灯②亮蓝灯，继续向左拨动旋钮则声音增大，反之向
“OFF”方向拨动旋钮则声音减小直至听到“滴”的一声关机；
②电源指示灯：充电时，指示灯长亮红灯；红灯熄灭，绿灯长亮表示电已充满；扩
音过程中红蓝灯闪烁表示低电压，当此红蓝灯闪烁时，请及时为扩音器充电；
③MIC输入插孔：ø3.5mm的麦克风插头插入此孔，进入扩音工作状态；操作时，
请不要将麦克风的拾音面朝向扩音器的扬声器，以免产生啸叫；
④AUX输入插孔：用ø3.5mm音频线将DVD、MP3等音乐信号导入本机，可做为有
源音箱使用；
⑤充电输入插孔：通过Type-C充电线为扩音器充电；
⑥挂扣：用于安装肩带，可将扩音器斜挂于肩上使用；
⑦背扣：用于将扩音器扣于腰带或裤腰上使用。
功能示意：
3
扩音器
E126A
④ ⑤ ①
③②
⑥
⑦

使用方法
1. 将头戴麦克风正确佩戴在头部，并调整好麦克风的拾音角度；
2. 将ø3.5mm的麦克风插头插入MIC输入插孔内；
3. 打开电源开关，电源指示灯亮蓝灯，调整音量旋钮到合适的音量；
4. 在使用过程中，若指示灯红蓝灯闪烁时，表示扩音器处于低电量状态，请及时充
电。
提示：初次使用时，建议先充满电；当电池充满时，请停止对电池充电，避免
电池过冲；如长时间不使用，需每半年充电一次，避免电池过放，并对电池性能产
生影响。
4
故障排除
项目 可能原因 解决方法
检查并插入正确的
麦克风输入插孔
扩音器没有声音
扩音器充不进电
头戴麦克风音头受潮
头戴麦克风插错位置
扩音器电池没电
充电器或充电线故障
更换一个头戴麦克风使用
及时为电池充电
更换充电器或充电线
扩音器
E126A

安全警示
1.使用产品时请确认所连接设备与本产品功率是否匹配以及合理调整设备音量大小，
不要在超过产品功率及大音量下长时间使用，以免造成产品异常和听力损伤；
2.使用中若发现有异常（如冒烟、异味等），请立即关闭电源开关并拨掉电源插头，
然后将产品送经销商检修；
3.本产品及附件都应放置在室内干燥通风处，勿长期存放在潮湿、灰尘多的环境，
使用中避免靠近火源，雨淋、进水、过度碰撞、抛掷、振动本机及覆盖通风孔，
避免损坏其功能；
4.若产品需要固定于墙壁或天花板上时，请确保固定到位，防止因固定强度不足导
致产品发生跌落危险；
5.使用该产品时需遵守相关安全规定，法律法规明确禁止使用场合请勿使用产品，
以免导致意外事故；
6.请不要自行拆机改装或维修，以防止出现人身伤害，如有问题或服务需求请联系
当地经销商跟进处理。
7.本产品不带电源适配器销售，消费者若使用电源适配器供电，则应购买配套使用
获得CCC认证并满足标准要求的电源适配器；
为避免电击、高温、着火、辐射、爆炸、机械危险以及使用不当等可能造成的人身
伤害或财产损失，使用本产品前，请仔细阅读并遵守以下事项：
5
扩音器
E126A

6
扩音器
E126A
环保说明

Preface
Features
○
○
○
○
○
○
○
○
Compact and lightweight mini amplifier
Rare earth material speaker, lightweight, good sound quality, loud sound
Digital sound reinforcement, 8W high-power audio output
Built-in large-capacity Lithium battery, energy-saving and environmentally
friendly, approx. 15h operation time
Used as a small speaker with its AUX input
Indicator light to display the real-time working status of the amplifier
Wearing it with a waist or shoulder strap for more convenient use
Ergonomic design, novel and stylish appearance
Dear Customer,
Thank you for purchasing TAKSTAR E126A Amplifier. Please read the user
manual carefully before use and keep it for reference in future.
If you have any questions or suggestions, please contact our local dealer.
Product content
Stra 1pc
User manual 1pc
7
Type-C charging cable 1pc
Waist strap clip 1pc
Headworn microphone 1pc
Amplifier 1pc
AMPLIFIER
E126A

Teaching, tour guide, training, promotion
Frequency Response: 150Hz-12KHz
Peak Power: 8W
Speaker Impedance: 4Ω
THD: THD≤1% 1KHz@4R,4W
Operating Voltage: 3.45V-4.2V
Battery Type: Li-ion battery
Battery Capacity: 3.7V/1800mAh
Charging: DC 5V 800mA
Charging Time: approx. 2.5h
Operation Time: approx. 15h
Weight: approx. 148g
Dimensions: 92mm*72.5mm*25mm
Cartridge: back electret cartridge
Polar Pattern: unidirectional
Frequency Response: 60Hz-16KHz
Sensitivity: -48.5dB±3dB (0dB=
1V/Pa, at 1KHz)
Note: The data is tested by Takstar Laboratory, and Takstar has the final
interpretation right!
Applications
Amplifier
Specifications
Headworn Microphone
8
AMPLIFIER
E126A

①Power switch & volume control knob: Turn the power switch towards the
"ON" direction till you hear the sound "da", indicating that the amplifier is
turned on, and the power LED lights up blue. The volume increases when you
continue to turn the power switch towards the "ON" direction. The volume
decreases when you turn the power switch towards the "OFF" direction, and
when you hear the sound "da", it means the amplifier is turned off.
②Power LED: The LED lights up red when the amplifier is charging and lights
up green when fully charged. When the LED flashes red and blue during
sound reinforcement, it means low battery and the amplifier needs to be
charged in time.
③MIC jack: Insert the ø3.5mm microphone plug into the MIC jack for sound
reinforcement. Please do not face the cartridge of the microphone to the
loudspeaker of the amplifier to avoid howling.
Function instructions
9
AMPLIFIER
E126A
④ ⑤ ①
③②
⑥
⑦

Operation instructions
1. Put the headworn microphone on your head and adjust the pickup angle of
the microphone.
2. Insert the ø3.5mm microphone plug into the MIC jack.
3. When the power switch is turned on, the power LED lights up blue. Adjust
the volume knob to a proper position.
4. If the power LED flashes red and blue during use, it indicates that the
battery is running low and needs to be charged in time.
Note: When using the amplifier for the first time, please fully charge it before
use. When the amplifier is fully charged, please stop charging it to avoid
overcharge of the battery. If the amplifier is not used for a long time, please
charge it once every six months to avoid over-discharge of the battery,
otherwise it will affect the battery performance.
10
④AUX jack: Connect to devices like DVD, MP3 via the ø3.5mm audio cable to
turn the amplifier into an active speaker.
⑤Charging jack: Charge the amplifier via the Type-C charging cable.
⑥Shoulder strap buckle: It is used to install the shoulder strap, and the
amplifier can be hung diagonally on the shoulder for use.
⑦Waist strap clip: It is used to buckle the amplifier on the belt or the
waistband for use.
AMPLIFIER
E126A

11
Troubleshooting
Problems Causes Solutions
Check and make sure the
headworn microphone is
plugged into the MIC IN jack.
There is no sound
from the amplifier.
Use another headworn
microphone.
The cartridge of the
headworn
microphone is damp.
The headworn mi
crophone is plugged
into the wrong jack.
The amplifier is out
of battery.Charge the amplifier in time.
Replace the charger or
the charging cable.
There is a malfunction
on the charger or the
charging cable.
The amplifier cannot
be charged.
AMPLIFIER
E126A

Safety instructions
1. When using the product, please confirm whether the power of the
connected device matches the power of the product, and adjust the volume
of the device. Do not use it for a long time when the power of the product is
exceeded or at a high volume to avoid product failure and hearing damage.
2. If there is any abnormality (such as smoke, odor, etc.) during use, please
turn off the power switch and unplug the power plug immediately, and then
send the product to the dealer for maintenance.
3. The product and accessories should be placed indoors in a dry and
ventilated place. Do not store them in a humid and dusty environment for a
long time. Avoid getting close to fire, rain, water, excessive collision,
throwing, vibrating the machine and covering the ventilation holes during
use, so as not to damage its function.
4. If the product needs to be fixed on the wall or ceiling, please make sure to
fix it in place to prevent it from falling down.
5. When using the product, you must abide by the relevant safety regulations.
Please do not use the product in the occasions that are clearly prohibited by
laws and regulations to avoid accidents.
6. Please do not disassemble, refit or repair the product by yourself to
prevent personal injury. If you have any questions or service needs, please
contact the local dealer for follow-up.
7. The product is sold without a power adapter. If you use a power adapter to
supply power, you should purchase and use a power adapter that has
obtained CCC certification and meets the standard requirements.
To avoid possible personal injury or property damage caused by electric
shock, high temperature, fire, radiation, explosion, mechanical hazards,
and improper use, please read and observe the following items before
using the product.
12
AMPLIFIER
E126A

13