Talex Eco CUT 210 Product information sheet

TALEX Spółka z ograniczoną odpowiedzialnością
Spółka komandytowa
ul. Dworcowa 9c, 77-141 Borzytuchom
tel. [phone]
e-mail. [email protected]
en.talex-sj.com
1
ORIGINAL USER MANUAL
SPARE PARTS CATALOGUE
WARRANTY
Eco CUT Rotary Mower
185, 165, 135 and 135 mini
And models with hydraulic lift: 210, 185, 165
Edition 3 Borzytuchom 2020

TALEX Spółka z ograniczoną odpowiedzialnością
Spółka komandytowa
ul. Dworcowa 9c, 77-141 Borzytuchom
tel. [phone]
e-mail. [email protected]
en.talex-sj.com
2
ATTENTION!
Before using the machine, please thoroughly read this User Manual and observe the safety
instructions contained herein.
The User Manual constitutes an inherent part of the machine!
Keep the User Manual in a safe place, where it should be accessible to the machine operator
during an entire lifespan of the machine.
In the event of its loss or damage, you must acquire a new copy from the machine dealer or
manufacturer.
If you sell or hand over the machine to another user, please attach the User Manual together
with the machine's operating instructions and its Declaration of Conformity.
The manufacturer reserves the copyrights to the User Manual.
Copying, processing of the User Manual and its parts without the manufacturer’s permission
is strictly prohibited.

TALEX Spółka z ograniczoną odpowiedzialnością
Spółka komandytowa
ul. Dworcowa 9c, 77-141 Borzytuchom
tel. [phone]
e-mail. [email protected]
en.talex-sj.com
3
TALEX guarantees the efficient operation of the machine, providing it is being used in
accordance with the technical and operating conditions specified in this USER MANUAL.
Any faults revealed during the warranty period will be repaired by the Warranty Service.
Expiration date of the warranty period is specified in the WARRANTY CARD.
Machine parts and components, which are subject to wear in normal operating conditions,
are not covered by the warranty, regardless of the warranty period.
Warranty Service covers only instances such as: mechanical damages not
caused by a fault of the user, production defects, etc.
The group of elements includes, among others, the following parts/components:
cutting blades,
protective aprons,
bearings.
In the event of damages resulting from:
mechanical destruction caused by a fault of the user or a traffic accident,
improper use, adjustment and maintenance, use of the machine for a purpose other
than intended,
use of a damaged machine
repairs conducted by unauthorized persons, improper repairs,
arbitrary changes and modifications of the machine structure,
the user’s rights to Warranty Service may become invalid.
The user is obliged to immediately report any noticed
damages of paint coat or spots of corrosion, and order repairs regardless
whether or not the damages are covered by the Warranty. Warranty conditions are specified
in detail in the WARRANTY CARD attached to the purchased machine.
ATTENTION!
You must demand from the dealer to properly fill out the Warranty Card. For example,
if the date of sale or the stamp of a dealer are missing, you risk that your complaints
will not be considered valid
ATTENTION!
After a few hours of the machine operation, check the tension of all V-belts.
If their play is too large, tighten them.

TALEX Spółka z ograniczoną odpowiedzialnością
Spółka komandytowa
ul. Dworcowa 9c, 77-141 Borzytuchom
tel. [phone]
e-mail. [email protected]
en.talex-sj.com
4
Table of Contents
1. Introduction..................................................................................................................................... 6
2. Machine identification .................................................................................................................... 7
3. Rules of safe operation.................................................................................................................... 8
3.1. User safety............................................................................................................................... 8
3.2. Residual risk assessment....................................................................................................... 12
3.3. Safety signs on the machine and their meaning ................................................................... 14
4. Intended use of the machine ........................................................................................................ 16
5. Equipment and accessories........................................................................................................... 17
5.1. Basic equipment.................................................................................................................... 17
5.2. Technical characteristics ....................................................................................................... 17
6. Machine usage............................................................................................................................... 20
6.1. Mower assembly ................................................................................................................... 20
6.2. Connecting the mower to a tractor....................................................................................... 24
6.3. Transport position................................................................................................................. 25
6.4. Working position ................................................................................................................... 28
6.5. Adjusting the mower............................................................................................................. 29
6.6. Operation of the mower........................................................................................................ 30
7. Operation and maintenance ......................................................................................................... 31
7.1. Adjustment of the V-belts tension ........................................................................................ 32
7.2. Replacing the blades: ............................................................................................................ 33
7.3. Maintenance after work........................................................................................................ 35
7.4. Lubrication............................................................................................................................. 36
7.5. End of season servicing ......................................................................................................... 37
7.6. Possible problems and solutions........................................................................................... 37
8. Disassembly, utilization and environment protection .................................................................. 38
9. Spare Parts Catalogue ................................................................................................................... 39
9.1. How to order spare parts ...................................................................................................... 39
9.2. General construction............................................................................................................. 41
9.2.1. Standard model –with metal bars................................................................................ 42
9.2.2. Model with hydraulic cylinder....................................................................................... 44
9.2.3. Suspension frame 1.85m / 1.65m ................................................................................. 46
9.2.4. Suspension frame 1.35m / 1.35mini ............................................................................. 47
9.2.5. Centre frame ................................................................................................................. 48
9.2.6. Cutting unit - main frame .............................................................................................. 56

TALEX Spółka z ograniczoną odpowiedzialnością
Spółka komandytowa
ul. Dworcowa 9c, 77-141 Borzytuchom
tel. [phone]
e-mail. [email protected]
en.talex-sj.com
5
9.2.7. Cutting unit –working part ........................................................................................... 59
13.2.8 Set of covers .................................................................................................................. 62
Complete drum unit ...................................................................................................................... 64
9.3. General construction –Eco CUT 210 mower ........................................................................ 66
9.3.1. Suspension system - Eco CUT 210................................................................................. 67
9.3.1. Middle frame –Eco CUT 210......................................................................................... 68
9.3.2. Hydraulic system –Eco CUT 210 ................................................................................... 71
9.3.1. Metal cover –Eco CUT 210............................................................................................ 73
9.3.2. Main frame - Eco CUT 210............................................................................................. 74
9.3.1. Cutting unit –working part - Eco CUT 210 .................................................................... 76
1) Step I.............................................................................................................................................. 78
2) STEP II ............................................................................................................................................ 79
3) STEP III ........................................................................................................................................... 80
4) STEP IV........................................................................................................................................... 80
5) STEP V............................................................................................................................................ 81
6) STEP VI........................................................................................................................................... 82
7) STEP VII.......................................................................................................................................... 83
8) STEP VIII......................................................................................................................................... 84
9) STEP IX ........................................................................................................................................... 86
10) STEP X ............................................................................................................................................ 87
11) STEP XI ........................................................................................................................................... 87
12) STEP XII .......................................................................................................................................... 88
13) STEP XIII ......................................................................................................................................... 89
10. Warranty........................................................................................................................................ 90
11. Records of warranty repairs.......................................................................................................... 91
12. Warranty form............................................................................................................................... 92

TALEX Spółka z ograniczoną odpowiedzialnością
Spółka komandytowa
ul. Dworcowa 9c, 77-141 Borzytuchom
tel. [phone]
e-mail. [email protected]
en.talex-sj.com
6
1. Introduction
Before the first use of the mower, you must thoroughly read and understand this User
Manual, and follow all the instructions contained herein.
This User Manual describes hazards, which may occur when you do not follow the safety
precautions when operating and maintaining the mower. The User Manual lists the safety
precautions which must be observed in order to minimize and to avoid the hazards.
The User Manual also contains the rules for proper use of the mower and explains the
required maintenance procedures.
If you do not understand any information contained herein, please contact directly the
manufacturer.
ATTENTION!
Before first use, read the User Manual
ATTENTION!
This warning symbol alerts about a hazard.
The warning symbol indicates an important hazard information
provided in the User Manual. Please read the information
carefully, follow the instructions and be exceptionally careful.

TALEX Spółka z ograniczoną odpowiedzialnością
Spółka komandytowa
ul. Dworcowa 9c, 77-141 Borzytuchom
tel. [phone]
e-mail. [email protected]
en.talex-sj.com
7
2. Machine identification
Each mower has its rating plate, containing the most important identification data. The
rating plate is located on the machine in a place, where it is easy to find and read.
Fig. 1 Rating plate
Manufacturer rating plate includes:
- full name of manufacturer,
- mower serial number,
- mower symbol,
- CE marking,
- weight,
- quality control mark,
- date of manufacture.

TALEX Spółka z ograniczoną odpowiedzialnością
Spółka komandytowa
ul. Dworcowa 9c, 77-141 Borzytuchom
tel. [phone]
e-mail. [email protected]
en.talex-sj.com
8
3. Rules of safe operation
3.1. User safety
The rotary mower can only be used by adults, who have learned its operation and read this
User Manual, and are properly qualified. Mowers should be handled with all safety
precautions, and in particular:
In addition to the guidelines outlined in this User Manual, observe also the general
principles of occupational health and safety!
Observe the warning symbols displayed on the machine.
It is strictly forbidden, that the machine shall be operated by anyone under the
influence of alcohol or other intoxicants.
Never allow the vehicle servicing the mower to be driven by a person other than the
mower operator, and under no circumstances allow any other persons to be on the
vehicle, or on the machine, during its operation.
The mower may be operated by a person with the proper authorization to drive the
vehicle to which it is attached, in accordance with the manufacturer's instructions.
The operating position of the operator, while working with the mower, is the cabin of
the vehicle to which the machine is attached.
Please note, that there are many elements of the mower that may cause an injury
(sharp edges, protruding parts, etc.). Use extra caution when moving around the
critical elements and obligatorily use the personal protective equipment, such as:
- protective clothing,
- protective gloves,
- protective footwear
It is forbidden to carry persons or objects on the machine.
It is forbidden, that the machine should be operated by persons, who are not
familiarized with the User Manual.
The mower operator should be provided with the first aid kit, containing also
instructions for its use.
When driving a vehicle with the attached, but not working mower, ensure the safe
transportation height of ~ 0,4m.
Before driving, the mower must be set to the transportation position, and raised with
the rear three-point hitch. When parking, the machine should be lowered.
Take special care when driving on public roads, and comply with the applicable road
traffic regulations.

TALEX Spółka z ograniczoną odpowiedzialnością
Spółka komandytowa
ul. Dworcowa 9c, 77-141 Borzytuchom
tel. [phone]
e-mail. [email protected]
en.talex-sj.com
9
When driving on public roads, it is essential to use the electric outline lighting of the
vehicle, check its efficiency and visibility, and keep it clean. The user is obliged to
ensure the visibility of a machine during its transportation: use the reflective
markings and warning signs - may be included as an option. The transportation speed
should be adjusted to the condition of a road surface, it should not, however, exceed
15 km/h.
Do not leave the vehicle with the mower on a hillside or on another sloping surface,
without securing the vehicle from rolling down. The mower should be lowered to the
ground. Truck wedges should be placed under the vehicle tires.
The mower must be adjusted to working height, during its attachment to the vehicle.
During the mower operation certain adjustment is possible, it should be done from
the inside of vehicle cabin, and operator should never leave the cabin.
Any preparations, fitting, dismantling or adjustment can be performed only after the
drive has been switched off, the engine stopped, the vehicle immobilized and when
all the moving parts of the machine have stopped.
After first hour of operation, check the status of all separable connections, including
bolts.
The mower should be kept on a flat, level, paved surface, out of the reach of
strangers and animals. For stabilizing the mower use the support foot.
During the fitting and dismantling of mower you should be careful, paying particular
attention to the structural elements used for fixing the mower to a vehicle.
Before using the mower you must check the condition of mower and of the vehicle it
is attached to. The vehicle and mower unit should be in good mechanical condition.
Immediately replace parts which are worn out or damaged.
The mower must be equipped with all the safety guards (provided by the
manufacturer), preventing access to any moving parts. The guards must be complete
and fully operational.
Work with the mower without the guards and mudguard is not allowed. Work with
the damaged guards or raised mudguard is forbidden.
It is also forbidden to lift the mower, while the drives are working and the reels are
rotating.
It is not allowed to control the lever of hydraulic lift from outside of the tractor.
Before beginning to work with the mower, you should familiarize yourself with the
way it operates, occupational safety rules and recommendations for maintenance
and adjustment procedures, by reading this User Manual.
Weight of the mower suspended on a vehicle can affect the vehicle’s
manoeuvrability. Under these circumstances you must exercise extreme caution.

TALEX Spółka z ograniczoną odpowiedzialnością
Spółka komandytowa
ul. Dworcowa 9c, 77-141 Borzytuchom
tel. [phone]
e-mail. [email protected]
en.talex-sj.com
10
The User Manual should be kept on the machine. When letting the machine to other
user, you must ensure that it is in good mechanical condition, and that the User
Manual is also handed over.
It is prohibited to attach any additional means of transportation to the mower.
During commissioning, check the machine functions and make the initial
adjustments, without a load.
Assembly protection of the three-point hitch of the mower with pins, should be
made only using the typical secure cotter pins. Using any other break-back devices is
prohibited.
Due to the natural wear, you must control the condition and completeness of the
machine cutting tools, following the instructions laid out in Chapter 7. Operation and
maintenance
On receipt of the mower after its transportation, you must make sure that the
machine has not been damaged and check its mechanical condition.
It is forbidden to stand under the raised mower, as it may result in being crushed by
the machine.
When adjusting, do not place your fingers and limbs between the structural elements
of the machine.
It is forbidden to leave a tractor’s cabin when the machine is running, and before all
the rotating parts have stopped
Operator of the vehicle working with a mower, must ensure that no person is
approaching the machine during its operation, and the distance of not less than 50m
from the working mower is always maintained.
Before switching on a mower’s drive, lower the cutting unit to its working position.
Mowing may be started only after PTO reaches the nominal speed of 540 rpm. It is
forbidden to overload the PTO shaft of the mower, and engage the clutch suddenly.
When turning, reversing or manoeuvring with the machine, you must ensure that
your visibility is adequate, or get assistance from a properly trained person.
It is prohibited to perform mowing while reversing the vehicle. When reversing, lift
up the machine.
When connecting the hydraulic lines, make sure that the hydraulic system is not
pressurized.
It is forbidden to stand between the vehicle and the mower, while the vehicle’s
engine is running.
Working on slopes exceeding 10% is not allowed.
Pay special attention when working on slopes.
When driving on curves and turning, switch off the PTO drive.

TALEX Spółka z ograniczoną odpowiedzialnością
Spółka komandytowa
ul. Dworcowa 9c, 77-141 Borzytuchom
tel. [phone]
e-mail. [email protected]
en.talex-sj.com
11
It is forbidden to operate the machine in close proximity of public squares (parks,
schools, etc.) or on stony grounds, to avoid the danger coming from the thrown out
stones and other objects.
Do not allow the PTO working speed to exceed 540 rpm, while driving speed must be
adjusted to the type of work being done.
Working with damaged or incomplete articulated telescopic shaft is forbidden. And it
is strongly forbidden to work without covers on moving parts.
The telescopic shaft has marks indicating which end must be connected to the
tractor, before work please make sure that the direction of rotation of the shaft is
correct.
Never leave a vehicle with the engine running. Before leaving the driver's seat (the
cabin), lower the machine to the ground, turn off the engine of the vehicle, remove
the ignition key, and apply the handbrake.
Make sure that during work, fitting, dismantling or adjustment of the machine, no
parts of your work clothing are unbuttoned or hanging loose. You should keep
elements of your clothing away from any machine parts that are likely to catch them.
It is advisable to clean and wash the mower in a washing stand equipped with a
sewage treatment feature or a settling tank, to neutralize the waste water.
The machine should be kept and stored in places protected from unauthorized access
of persons and animals, thus eliminating the risk of accidental injuries, on a flat,
hardened surface, under a protective canopy.
In the event of failure, immediately switch off the drive transferring power from the
vehicle to the mower.
When working with the mower, use hearing protection headphones to minimize the
exposure to noise. In addition, it is recommended to close the doors and windows of
the vehicle’s cabin.
Failure to observe the above guidelines may present danger for the operator and
other persons, as well as damage the mower.
The user is responsible for any damages caused by the non-compliance to the
above principles.

TALEX Spółka z ograniczoną odpowiedzialnością
Spółka komandytowa
ul. Dworcowa 9c, 77-141 Borzytuchom
tel. [phone]
e-mail. [email protected]
en.talex-sj.com
12
3.2. Residual risk assessment
Talex company has made every effort to ensure that the design of the mower, and its
intended use, do not pose any risk to persons or the environment.
Due to the nature of work being done by the mower and, for example, the inability to
completely cover the machine’s cutting unit, certain risk factors may occur.
No.
Hazard
Hazard source (cause)
Hazard protection measures
1
Drive system
overload (physical
weight)
Work in a standing, forced-bent
position, walking, moving items
Reading and understanding the User Manual,
workplace training including lifting standards
for the manual transportation labour, proper
techniques for lifting and carrying weights,
use of another person's assistance, moving
equipment such as jacks, winches
2
Fall on the same
level (tripping,
slipping, etc.)
Uneven terrain, messy
environment - objects lying and
standing around, cables lying
on communication roads,
slippery surfaces
Suitable footwear, level ground, paying
attention, maintaining order, familiarization
with the User Manual
3
Hitting stationary,
protruding parts
of the machine
Machine and its surroundings
Proper positioning of a machine, safe space to
move around, proper organization of work,
paying attention, familiarization with the User
Manual
4
Being hit by
moving objects
Mowed plants, accidentally
removed soil, stones
Paying attention, establishing a danger zone,
prohibiting any traffic near the working
machine, banning persons from standing
within the 50m range from the working
machine, using personal protective
equipment - protective helmet, glasses,
familiarization with the User Manual
5
Sharp, dangerous
edges
Protruding structural elements
of the machine, use of manual
tools
Personal protective measures –protective
gloves, buttoned up work clothes, paying
special attention
6
Belt transmission
systems
Fast moving transmission
pulleys and belts, rotating
articulated telescopic shaft, no
covers on the movable parts
Elimination of moving around, approaching
and regulating the machine, which is running,
paying special attention, familiarization with
the User Manual
7
Weight of the
suspended
Improper mounting,
aggregating, wrong setting of
Paying special attention, use of personal
protective equipment - safety footwear,

TALEX Spółka z ograniczoną odpowiedzialnością
Spółka komandytowa
ul. Dworcowa 9c, 77-141 Borzytuchom
tel. [phone]
e-mail. [email protected]
en.talex-sj.com
13
standing machine
the machine, improper
operation, leaving the
suspended machine on a
tractor
protective gloves, secure setting of the
machine, help of another person, use of lifting
jacks, davits, familiarization with the User
Manual
8
Microclimate -
changing weather
conditions
Work performed in different
weather conditions
Suitable working clothes, beverages, creams
with sunscreen, proper rest, familiarization
with the User Manual
9
Noise
Too high rotational speed of
the machine, damaged, loose,
vibrating parts
Work only with the machine in good
mechanical condition, regular inspections,
proper rotational speed, familiarization with
the User Manual

TALEX Spółka z ograniczoną odpowiedzialnością
Spółka komandytowa
ul. Dworcowa 9c, 77-141 Borzytuchom
tel. [phone]
e-mail. [email protected]
en.talex-sj.com
14
3.3. Safety signs on the machine and their meaning
1.0 - Prior to using the machine,
read the User Manual
1.1 - Switch off the engine and
remove the ignition key before
beginning any servicing or
maintenance procedures
1.2 - Keep a safe distance from
the machine. Do not allow
unauthorized persons within
the range of 50 m from the
machine
1.3 –Do not attempt to perform
any repairs while working
1.4 - Do not ride on platforms and
ladders
1.5 - Do not stand near the
lifting jack connectors, when
controlling the jack
1.6 - Do not open or remove
safety guards, when the engine is
running
1.7 - Keep a safe distance from
power lines
1.8 - Avoid impact of liquids
flowing under pressure. Read the
User Manual and learn about the
operation procedures

TALEX Spółka z ograniczoną odpowiedzialnością
Spółka komandytowa
ul. Dworcowa 9c, 77-141 Borzytuchom
tel. [phone]
e-mail. [email protected]
en.talex-sj.com
15
1.9 –Caution, loose rotation tools
2.0 - Caution, cutting blades. Do
not approach a working mower
2.1 Caution, V-belts. Keep
away
2.2 –Warning message about
pressure in the hydraulic system
2.3 - Use protection
suit
2.4 –Use
protective
gloves
2.5 –Use hearing
protectors
2.6 –Use
protection
goggles
2.7 Do not raise the rotating
machine
2.8 Shaft connection of mower with tractor
2.9 Do not exceed the maximum RPM
2.10 Correct arrangement in a given
position
Table 1 Safety signs on the machine and their meaning

TALEX Spółka z ograniczoną odpowiedzialnością
Spółka komandytowa
ul. Dworcowa 9c, 77-141 Borzytuchom
tel. [phone]
e-mail. [email protected]
en.talex-sj.com
16
4. Intended use of the machine
The rotary mower is designed for agricultural applications, mowing of the low growing green
forage like grasses, alfalfa, etc., on fields and meadows with flat surfaces.
It can be used in fields and meadows, which contain no stones, are flat or slightly undulating,
with the slope of up to 10 °.
The mower is a machine suspended on the three-point hitch system of the category I and II
tractor. The working elements are two rotating discs, fitted with blades. This unit is driven
from power transmission shaft, through articulated telescopic shaft and belt transmission to
bevel gears. The bevel gears are embedded on the drive shafts, which drive the discs.
Complying with the requirements related to the use of the machine, its operation and
repairs, strictly according to the manufacturer's guidelines, is the precondition of the use of
the machine as intended. The machine should be used, operated and repaired only by
persons familiar with its specific characteristics, who have learnt the rules of conduct
prescribed by the occupational health and safety regulations.
The manufacturer offers a wide range of agricultural machinery. It can also provide
professional advice in terms of choosing the right equipment for your needs.
Any doubts concerning the machine’s intended use should be resolved by
contacting its manufacturer. Selection of the appropriate product and knowing
the range of its intended use will contribute to the occupational safety.
Using the machine for any other purpose shall be considered contrary to the intended use.

TALEX Spółka z ograniczoną odpowiedzialnością
Spółka komandytowa
ul. Dworcowa 9c, 77-141 Borzytuchom
tel. [phone]
e-mail. [email protected]
en.talex-sj.com
17
5. Equipment and accessories
5.1. Basic equipment
Basic equipment of the mower consists of:
User Manual together with Spare Parts Catalogue and Warranty Card - 1pc.
Special spanner - 1pc.
Set of blades - for number see Table No. 2.
Set of spare blades
For Eco CUT 210 –PTO shaft 460Nm L-860 and hydraulic cylinder -1pc.
Basic equipment of the mower does not include warning signs with lights, slow moving
vehicle triangle, and articulated telescopic shaft. The above items can be purchased
additionally from the manufacturer or at the machines’ point of sale.
5.2. Technical characteristics
The overall construction of the mower is shown in the following figure.
Figure 2 Overall machine construction: 1 - suspension frame; 2 –main chassis; 3 –connectors unit/cylinder
(depending on the model); 4 –cutting unit; 5 –cover assembly covers; 6 –working section of cutting unit;
7 –support foot.
Suspension system frame is used to connect the mower to a tractor. Through centre frame,
the suspension system frame is connected to the complete working unit with covers.

TALEX Spółka z ograniczoną odpowiedzialnością
Spółka komandytowa
ul. Dworcowa 9c, 77-141 Borzytuchom
tel. [phone]
e-mail. [email protected]
en.talex-sj.com
18
The working unit consists of two working drums, with cutting blades rotationally embedded
in the lower part of the drums. Diagram of the drive system is shown in Figure 3.
Figure 3 Drive system diagram: 1 –articulated telescopic shaft; 2 –drive head shaft; 3 –freewheel clutch (on
large pulley); 4 –V-belt transmission; 5 –main frame shaft; 6 –bevel gear; n1 –rotational speed of tractors
PTO; n2 –rotational speed of drums (values given in Table 2); z1 –large bevel gear; z2 –small bevel gear.
Figure 4 Eco CUT 210 drive system diagram: 1 –articulated telescopic shaft with one-way clutch; 2 –drive
head shaft; 4 –V-belt transmission; 5 –main frame shaft; 6 –bevel gear; n1 –rotational speed of tractors PTO;
n2 –rotational speed of drums (values given in Table 2); z1 –large bevel gear; z2 –small bevel gear.
The drums are driven by the tractors PTO shaft. Together with the blades, they rotate in
opposite directions, cutting plants and forming green forage in a swath. The one-way clutch
allows the drums to rotate freely after the engine is shut off, and protects the driving
elements from damage.
Technical-operational data for mowers are provided in Table 2.

TALEX Spółka z ograniczoną odpowiedzialnością
Spółka komandytowa
ul. Dworcowa 9c, 77-141 Borzytuchom
tel. [phone]
e-mail. [email protected]
en.talex-sj.com
19
UOM
Mower model
Eco CUT
210
185
165
135
135mini
No.
Type
2.10m
1.85m
1.65m
1.35m
1.35mini
Symbol
Z-042/3
Z-042/2
Z-042/1
Z-042
Z-080
1
Type of mower
-
Rotary suspended
2
Mowing width
[m]
2.10
1.85
1.65
1.35
1.35
3
Power requirement
[kW]
70
60
40
25
4
Number of cutting drums
[pcs.]
2
5
Number of blades
[pcs.]
8
6
4
6
Standard cutting height
[mm]
40
40
40
36
36
7
Low cutting height
[mm]
35
32
36
32
32
8
Rotational speed of working drums
[rpm]
1545
1790
2020
2300
9
Rotational speed of tractor’s PTO
[rpm]
540
10
Recommended PTO
[cat.]
IV
II
[Nm]
460**
460
270
11
Work efficiency
[ha/h]
Up to 2,5
~ 1,6
~ 1,4
~ 1
~ 0.8
12
Working speed
(km/h)
8
13
Transportation speed
[km/h]
15
14
Transportation clearance
[m]
0.4
Overall dimensions in transportation position (with shield covers assembly, vertical position)
Model
[mm]
210
185 /
hydr.
165 / hydr.
135
135
mini
15
Length
[mm]
2460
3450/2450
3180/2200
2760
2280
16
Width
[mm]
1750
1350
1220
1220
1010
17
Height
[mm]
3060
1830/2800
1830/2250
1730
1350
Overall dimensions in working position (with shield covers assembly)
18
Length
mm
1750
1350
1220
1200
1010
19
Width
mm
4220
3600
3200
2800
2300
20
Height
mm
1090
1430
1430
1430
1050
21
Weight
kg
562
430
369
338
310
22
Nominal pressure in the hydraulic
system / for models with hydraulic
cylinder
MPa
16
N/A
* The overall dimensions may differ when aggregated with a particular tractor
**with one-way clutch
Table 2 Mowers’ technical-operational data

TALEX Spółka z ograniczoną odpowiedzialnością
Spółka komandytowa
ul. Dworcowa 9c, 77-141 Borzytuchom
tel. [phone]
e-mail. [email protected]
en.talex-sj.com
20
6. Machine usage
The manufacturer declares that the machine is fully functional. It has been inspected in
accordance
with the quality control procedures and approved for use. However, this does not relieve the
user from the obligation to inspect the machine after its delivery.
Before every time the machine is used, its mechanical condition needs to be
checked, and especially the condition of cutting unit, drive transmission system,
hydraulic system and guarding shields.
6.1. Mower assembly
The manufacturer delivers a complete mower with an unmounted cover of the cutting unit.
Installation of the cutting unit cover must be done by the user.
Working without the cutting unit cover, or with the cover damaged or raised,
poses a danger for an operator and for environment –Strictly prohibited.