Tannoy VS10 BP User manual

VS10 BP
Owners Manual

CONTENTS
1. Introduction
2. Unpacking
3. Connectors/Cabling
4. System Configurations
5. Amplification & Power Handling
6. Equalisation/Placement
7. Dimensions
8. Performance Data
9. Technical Specifications
10. Rigging & Suspension
11. System Configurations & OEM Controllers
12. VS15BP Service Parts & Accessories
13. Warranty
14. Declaration of Conformity

1. Introduction
The Tannoy VS10BP is a compact, versatile subwoofer system, designed to
extend the low frequency response of the V series loudspeakers and increase
system headroom.
The VS10BP will extend the frequency response of these systems to below 40Hz
and is capable of providing output levels normally be associated with considerably
larger enclosures.
The VS10BP comprises one high efficiency 250mm(10”) drive unit. The compact
dimensions of the V10BP enable it to be used in applications without being
obtrusive, such as underneath seating and bars. M10 rigging points are also
provided to allow permanent installation. Versatility is further enhanced by the
introduction of blanking plates, which allow the bass ports to be moved to another
face of the cabinet allowing installation in various orientations.
2. Unpacking
Every Tannoy VS10BP is carefully inspected before packing. After unpacking your
loudspeaker, please inspect for any exterior physical damage, and save the
carton and any relevant packaging materials in case the loudspeaker again
requires packing and shipping. In the event that damage has been sustained in
transit notify your dealer immediately.
3. Connectors/Cabling
Cable choice consists mainly of selecting the correct cross sectional area in
relation to the cable length and the load impedance. A small cross sectional area
would increase the cables series resistance, inducing power loss and response
variations (damping factor).
Connectors should be wired with a minimum of 2.5 sq. mm (12 gauge) cable. This
will be perfectly satisfactory under normal conditions. In the case of very long
cable runs the wire size should exceed this, refer to the following table for
guidance:-
CABLE RUN (m)
C.S.A. OF EACH
CONDUCTOR (mm)
CABLE
RESISTANCE Ω
% POWER LOSS
INTO 8ΩLOAD
% POWER LOSS
INTO 4ΩLOAD
10
2.5
4.0
6.0
0.14
0.09
0.06
1.7
1.1
0.73
3.5
2.2
1.5
25
2.5
4.0
6.0
0.35
0.22
0.14
4.3
2.7
1.8
8.6
5.4
3.6
50
2.5
4.0
6.0
0.69
0.43
0.29
8.6
5.4
3.6
17.0
11.0
7.2
100
2.5
4.0
6.0
1.38
0.86
0.58
17.0
11.0
7.2
35.0
22.0
14.0
The VS10BP is fitted with two pairs of 4mm binding posts (Fig1) for the amplifier
input and highpass output connectors to the satellite loudspeakers. An external
active crossover such as the TDX1 or TDX2 is not necessary but will increase the

versatility of the system allowing relative attenuation between the subwoofer and
satellite loudspeakers and provide delay if required as well as driver protection
and optimal integration.
4. System Configurations.
Configuration 1.
The most basic configuration would be a VS10BP and up to two-8ohm satellite
amplifier. The ‘performance data’ section of this manual shows the impedance
presented to the amplifier with one and two V8 (8ohm) loudspeakers.
Configuration 2.
A TDX1/TDX2 or other OEM system controller can be used to further enhance
and increase the flexibility of the system. A system controller will allow the relative
levels of the satellites and VS10BP to be adjusted separately. Limiters, delay and
FROM AMP (CH1)
TO INPUT
+
-
V series
V series
FROM HI-PASS OUT
VS10BP Termination Panel

optimal crossover points are also afforded by the introduction of a system
controller.
A loudspeaker driven actively as shown below offers a number of other
performance advantages, such as increased system headroom. Audio program
materiel is made up of many different frequencies and harmonics. In music
materiel, most of the energy is in the low frequencies, with less in the highs. When
both high and low frequencies are present in a signal, the stronger low
frequencies can use up amplifier power, leaving little or no reserve for the highs,
so they are more likely to cause the power amplifier to clip. In an active driven
system, a smaller amp can handle high frequencies, LF amp clipping is less of a
factor, and less overall amplifier capacity is needed due to the efficiency
improvement in the absence of a passive crossover.
5. Amplification & Power Handling
As with all professional loudspeaker systems, the power handling is a function of
voice coil thermal capacity. Care should be taken to avoid running the amplifier
into clip (clipping is the end result of overdriving any amplifier). Damage to the
loudspeaker will be sustained if the amplifier is driven into clip for any extended
period of time. Headroom of at least 3dB should be allowed. When evaluating an
amplifier, it is important to take into account its behaviour under low impedance
V series
-
+
TO INPUT
V series
+
-
+
- -
+
POWER AMP
POWER AMP
TX CONTROLLER
OR ELECTRONIC X-OVER
FROM
SOURCE
+
-
+
-

load conditions. A loudspeaker system is highly reactive and with transient signals
it can require more current than the nominal impedance would indicate.
Generally a higher power amplifier running free from distortion will do less damage
to the loudspeaker than a lower power amplifier continually clipping. It is also
worth remembering that a high powered amplifier running at less than 90% of
output power generally sounds a lot better than a lower power amplifier running at
100%. An amplifier with insufficient drive capability will not allow the full
performance of the loudspeaker to be realised.
It is important when using different manufacturers’ amplifiers in a single installation
that they have very closely matched gains, the variation should be less than +/-
0.5dB. This precaution is important to the overall system balance when only a
single active crossover is being used with multiple cabinets; it is therefore
recommended that the same amplifiers be used throughout.
6. Equalisation/Placement
The VS10BP is designed to need no equalisation or correction to overcome
system limitations. As a result, it will only need equalisation to compensate for
difficult acoustic environments.
Excess equalisation can reduce system headroom, and introduce phase distortion
resulting in greater problems than it cures. If equalisation is required then it should
be applied gently and smoothly. Violent equalisation will be detrimental to the
overall sound quality.
The frequency band over which a subwoofer operates is essentially omni-
directional, therefore efficiency of the VS10BP may be further enhanced if the unit
is placed against a wall, where the radiation in the forward plane will be doubled
due to the addition of the reflected rear directed energy, and a 3dB increase in
sound pressure will occur. If another boundary is introduced, say a floor, then the
effective radiation space is halved again, resulting in a further 3dB lift, and if
placed in a corner, once again the sound pressure level will increase by a further
3dB.
The compact dimensions of the VS10BP allow the VS10BP to fit into small
spaces. A unique feature incorporated into the VS10BP further enhances this
flexibility;
The Bass Ports on the VS10BP can be moved onto the other face of the cabinet
as shown below. Simply remove the blank plates and Bass ports and swap
positions. Each chamber in the enclosure utilizes a different length bass port. To
avoid placing the wrong Bass port in the wrong chamber the holes in the
enclosure are ‘Keyed’.
The features described above allow the VS10BP to be placed in any orientation.

7. Dimensions
355.0
365.0 590.0

KEYS

9. Technical Specifications
Frequency response (1) +/- 3dB 39Hz - 110Hz
35Hz (-10dB)
Recommended Amplifier Power 200 - 400 watt / 8 ohm
Power Handling Average(2) Programme Peak (10ms)
200 watt 400 watt 800 watt
Sensitivity (1)
2.83 volt @ 1m 95 dB (half space conditions)
Maximum SPL (3) Average Peak
@ 1m 118 dB 124 dB
Impedance Nominal 8.0 ohm
Minimum 6.0 ohm
Driver Complement 1 x 10” (250mm) LF Driver
Type number 2532
Recommended Crossover Point 80Hz - 110Hz, 24dB/octave
Recommended High-pass filter-35Hz, 24dB/octave
Internal passive crossover @ 110 Hz
Enclosure 50 litre (1.56 cu ft) vented
Finish Textured black paint (optional in white)
Connectors 2 x Pair 4mm Binding Posts
Input & passive highpass output
Fittings 2 x Blanking plate allows bass ports to be moved to another facia
8 x M10 flying inserts.
Dimensions 355mm(H) x 365mm(W) x 590mm(D)
14 “(H) x 14.4”(W) x 23.25”(D)
Weight 17.5 Kg (38.5 lbs)
NOTES: (1) Average over stated bandwidth. Measured at 1m on axis.
(2) Long term power handling capacity as defined in EIA standard RS - 426A.
(3) Unweighted pink noise input, measured at 1m in half space conditions.
Tannoy operates a policy of continuous research and development. The introduction of new materials or manufacturing
methods will always equal or exceed the published specifications which Tannoy reserve the right to alter without prior
notice. Please verify the latest specifications when dealing with critical applications.

10. Rigging & Suspension
General Safety Advice
WARNING: As the legal requirements for flying change from country to country,
please consult you local safety standards office before installing any product. We
also recommend that you thoroughly check any laws and bylaws prior to
commencing work. Qualified personnel trained in safe rigging practices should
only suspend the system.
Whenever a Tannoy Professional loudspeaker is fixed to a surface using a
Tannoy
Professional hardware device, the installer must ensure that the surface is
capable of safely and securely supporting the load. The hardware employed must
be safely and securely, attached both to the loudspeaker and also to the surface
in question, using only the fixing holes provided. Secure fixings to the building
structure are vital. Seek help from architects, structural engineers or other
specialists if in any doubt.
All loudspeakers flown in theatres, nightclubs, conference centre or other places
of work and entertainment must, be provided with an independent, correctly rated
and securely attached secondary safety – in addition to the principle hardware
device. This secondary safety must prevent the loudspeaker from dropping more
than 150mm (6”) should the principle hardware device fail.
Threaded inserts are fitted to the VS10BP to allow the suspension of a single
enclosure. Never suspend one enclosure from another to form an array or cluster
using only these fittings.
If eyebolts are being used then only forged shoulder eyebolts should be used
with a thread length of 30mm (see section 8.3).
SECUR ET – VEB Eyebolt
7.
!
The Tannoy VS10BP loudspeaker can be
flown with high quality VEB M10 eyebolts with
collar to BS4278:1984. The loudspeaker is
equipped with internal steel braces, which also
double as the flying points, and accept VEB
M10 eyebolts.
To install the VEB M10 eyebolts remove the
original M10 counter sunk screws from the
locations you wish to install the VEB M10
eyebolts. Then replace these counter sunk
M10 screws with the VEB M10 eyebolts.
Important: It is imperative for safety reasons
that two eyebolts linked to two independently
fixed straps are used per cabinet. VEB
eyebolts should be installed into the relative
sides of the cabinet, and should NEVER be
installed on the top of the cabinet. Never
suspend one enclosure from another to form
an array or cluster using these fittings.
Never attempt to use formed eyebolts i.e.
formed from a steel rod and bent into an eye.

11. System Configurations & OEM Controllers
With the vast array of digital loudspeaker management systems available it is
inevitable that the user may opt to use a controller other than a Tannoy controller
as part of a large scale integrated system. The VS10BP has been designed to
need no external equalisation to overcome system limitations. Below is a list of
recommended parameters; these parameters can be further tailored depending
on the acoustic environment or specific application:-
Parameter
Unit/Name
Gain
(dB)
User definable
Delay
(ms)
User definable
Polarity
Positive
HPF
Freq (Hz)
35
Slope (dB/oct)
24
Filter Shape
Butterworth
LPF
Freq (Hz)
80 – 110
Slope (dB/oct)
24
Filter Shape
Butterworth
Freq (Hz)
65
Level (dB)
+3
Type
Parametric
PEQ 1
Q / Bandwidth
2.5
12. VS10BP Service Parts & Accessories

Part Number Description
7900 xxxx Driver Kit - 2532
7900 xxxx Recone Kit - 2532
8001 2820 VEB – Secur ET – Eyebolts M10
13. Warranty
No maintenance of the VS10BP loudspeaker is necessary.
All Tannoy professional loudspeaker products are covered by a 5 year warranty
from the date of manufacture subject to the absence of misuse, overload or
accidental damage. Claims will not be considered if the serial number has been
altered or removed. A Tannoy Professional dealer or service agent should only
carry out work under warranty. This warranty in no way affects your statutory
rights. For further information please contact your dealer or distributor in your
country. If you cannot locate your distributor please contact Customer Services,
Tannoy Ltd at the address given below.
Customer Services
Tannoy Ltd.
Rosehall Industrial Estate
Coatbridge
Strathclyde
ML5 4TF
Scotland
Telephone: [phone] (National)
[phone] (International)
Fax: [phone] (National)
[phone] (International)
E-Mail: [email protected]
DO NOT SHIP ANY PRODUCT TO TANNOY WITHOUT PREVIOUS AUTHORISATION
Our policy commits us to incorporating improvements to our products through
continuous research and development. Please confirm current specifications for
critical applications with your supplier.
14. Declaration of Conformity
The following apparatus is/are manufactured in the United Kingdom by Tannoy Ltd of
Rosehall Industrial estate, Coatbridge, Scotland, ML5 4TF and conform(s) to the

protection requirements of the European Electromagnetic Compatibility Standards and
Directives relevant to Domestic Electrical Equipment. The apparatus is designed and
constructed such that electromagnetic disturbances generated do not exceed levels
allowing radio and telecommunications equipment and other apparatus to operate as
intended, and, the apparatus has an adequate level of intrinsic immunity to
electromagnetic disturbance to enable operation as specified and intended.
Details of the Apparatus: Tannoy Contractor Loudspeaker
Model Number: VS10BP
Associated Technical File: EMCVS10
Applicable Standards: EN 55103-1 Emission
EN 55103-2 Immunity
EN60065 Electrical Safety
Signed:
Position: Engineering Director
Tannoy Professional
Date: 4th July 2004
For Tannoy Ltd

Check periodically for the latest manual revision that will always available for download from
www.tannoy.com The revision number of this manual is located below
Tannoy United Kingdom T: [phone] F: [phone] E: [e-mail]
Tannoy North America T: [phone]  F: [phone]  E: [email protected]