TaoTronics TT-AP003 User manual
E-mail:
MANUFACTURER
Manufacturer: Shenzhen NearbyExpress Technology Development Co.,Ltd.
Address: Floor 7, Building E, Galaxy World Phase II, Shenzhen, China
Learn more about the EU Declaration of Conformity:
https://www.taotronics.com/pages/user-manual
Rev_1.1_EN-DE
Model: TT-AP003
Air Purifier
User Guide
IMPORTANT SAFETY INSTRUCTIONS
Specifications
Knowing Your Air Purifier
Getting Started
Using Your Air Purifier
Replacing the HEPA Filter
Cleaning and Maintenance
Troubleshooting
Warranty and Service
01
02
02
03
04
07
08
10
12
English ---------------------------------
Deutsch --------------------------------
01-13
15-28
Languages
Contents
Thanks for choosing TaoTronics Air Purifier. Please read this User Guide thoroughly before use and
retain it for future reference.
FOR HOUSEHOLD USE ONLY
READ AND SAVE THESE INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
BEFORE USING THIS APPLIANCE READ ALL INSTRUCTIONS AND CAUTIONARY MARKINGS
IN YOUR USER GUIDE AND ON THE APPLIANCE
When using electrical appliances, basic precautions should always be followed to reduce the risk
of fire, electric shock, and injury to persons, including the following:
• Read all instructions before using the appliance.
• IMPORTANT - This appliance has a polarized plug (one blade is wider than the other). To reduce
the risk of electric shock, this plug is intended to fit in a polarized outlet only one way. If the plug
does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician.
Do not attempt to rig this safety feature.
• This appliance is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they have been
given supervision or instruction concerning the use of the appliance by person responsible for
their safety.
• To avoid fire or shock hazard, plug the appliance directly into a right AC electrical outlet.
• Keep the cord out of heavy traffic areas. To avoid fire hazard, NEVER put the cord under rugs,
near heat registers, radiator, stoves, or heaters.
• To protect against electrical hazards, DO NOT immerse in water or other liquids. Do not use
near water.
• Children cannot recognize the hazards associated with the usage of electrical appliances. For
this reason, always supervise children when they are near the unit.
• Always unplug the air purifier before moving it, opening the grille, changing filters, cleaning or
whenever the air purifier is not in use. Be sure to pull by the plug, not the cord.
• NEVER drop or insert any objects into any openings.
• DO NOT run the cord under carpeting.
• DO NOT cover the cord with throw rugs or similar coverings.
• DO NOT route the cord under furniture or appliances. Arrange the cord away from traffic area
and where it will not be tripped over.
• DO NOT operate any appliance with a damaged cord or plug, if the motor fan fails to rotate,
after the appliance malfunctions, or if it has been dropped or damaged in any manner. Send to
Customer Service for assistance.
• Use appliance only for intended household purposes as described in this manual. Any other use
is not recommended that may cause fire, electric shock, or injury to persons.
• DO NOT place anything on top of the unit.
• NEVER block the air openings, grille / outlets or place the unit on a soft surface such as a bed or
sofa, as this could cause the unit to tip over, blocking the air inlet or outlet.
• DO NOT attempt to repair or adjust any electrical or mechanical functions on this unit. Doing so
will void your warranty. The inside of the unit contains no user serviceable parts. All servicing
should be performed by qualified personnel only.
01 03 05 07
09 11 13 15
17 19 21 23
25 27
02 04 06
08 10 12 14
16 18 20 22
24 26 28 30 32
Knowing Your Air Purifier
Air Outlet Grille
Control Panel Handle
Air Inlet Grille Pre-Filter HEPA Filter
Getting Started
Specifications
Model
Operating Voltage
Rated Power
Noise 55 dB (High Speed)
TT-AP003
220-240V~50/60 Hz
36 W
1Open Air Inlet Grill. 2Press down U-shaped snap joint
to take out Pre-Filter.
3Hold pull tabs to take out
HEPA Filter.
4Remove from its plastic packaging.
5Place HEPA Filter back (pull
tabs facing out).
6Align the slots and install Pre-Filter
back.
15in/
38cm
7Align the slots and buckle
up Air Inlet Grill.
8Place the unit on a firm, level and flat
surface.
15in/
38cm
LED Display
01 03 05 07
09 11 13 15
17 19 21 23
25 27
02 04 06
08 10 12 14
16 18 20 22
24 26 28 30 32
Knowing Your Air Purifier
Air Outlet Grille
Control Panel Handle
Air Inlet Grille Pre-Filter HEPA Filter
Getting Started
Specifications
Model
Operating Voltage
Rated Power
Noise 55 dB (High Speed)
TT-AP003
220-240V~50/60 Hz
36 W
1Open Air Inlet Grill. 2Press down U-shaped snap joint
to take out Pre-Filter.
3Hold pull tabs to take out
HEPA Filter.
4Remove from its plastic packaging.
5Place HEPA Filter back (pull
tabs facing out).
6Align the slots and install Pre-Filter
back.
15in/
38cm
7Align the slots and buckle
up Air Inlet Grill.
8Place the unit on a firm, level and flat
surface.
15in/
38cm
LED Display
01 03 05 07
09 11 13 15
17 19 21 23
25 27
02 04 06
08 10 12 14
16 18 20 22
24 26 28 30 32
Using Your Air Purifier
Control Panel
LED Display Screen
Air Quality Sensor
Fan Speed
1 / 2 / 3
Auto Mode
Automatically adjust fan speed
ON/StandbyAuto OFF Timer (1/2/4/8h)
Reset Filter
Child Lock Sleep Mode
CHILD LOCK
(Long press 3s)
AUTO MODE SLEEP MODE ON/STANDBYTIMER
(Long press 3s to
reset the filter)
SPEED
——
Blue
Green
Orange
Red
Auto OFF Timer
PM2.5 Value
Sleep Mode
Auto Mode
Air Quality Indicator
Excellent
Good
Moderate
Poor
Filter Change
Child Lock
Tap to activate Auto Mode.
When Auto Mode is enabled, the fan speed is adjusted intelligently according to the air quality.
Quick Start of Your Air Purifier
Operation and Functions
Indicator ON
Auto Mode
Indicator ON
ON/STANDBY
The air purifier will always remember your last settings (except timer) when turned off, and will
resume these settings when it is turned back on.
Memory Function
——
——
——
1Plug into an appropriate electrical outlet. 2Tap to turn ON the air purifier.
ON/STANDBY
3Tap to activate Auto Mode, the fan speed
will be adjusted intelligently.
4Tap to turn OFF when finished
using it.
Using Your Air Purifier
01 03 05 07
09 11 13 15
17 19 21 23
25 27
02 04 06
08 10 12 14
16 18 20 22
24 26 28 30 32
Using Your Air Purifier
Control Panel
LED Display Screen
Air Quality Sensor
Fan Speed
1 / 2 / 3
Auto Mode
Automatically adjust fan speed
ON/StandbyAuto OFF Timer (1/2/4/8h)
Reset Filter
Child Lock Sleep Mode
CHILD LOCK
(Long press 3s)
AUTO MODE SLEEP MODE ON/STANDBYTIMER
(Long press 3s to
reset the filter)
SPEED
——
Blue
Green
Orange
Red
Auto OFF Timer
PM2.5 Value
Sleep Mode
Auto Mode
Air Quality Indicator
Excellent
Good
Moderate
Poor
Filter Change
Child Lock
Tap to activate Auto Mode.
When Auto Mode is enabled, the fan speed is adjusted intelligently according to the air quality.
Quick Start of Your Air Purifier
Operation and Functions
Indicator ON
Auto Mode
Indicator ON
ON/STANDBY
The air purifier will always remember your last settings (except timer) when turned off, and will
resume these settings when it is turned back on.
Memory Function
——
——
——
1Plug into an appropriate electrical outlet. 2Tap to turn ON the air purifier.
ON/STANDBY
3Tap to activate Auto Mode, the fan speed
will be adjusted intelligently.
4Tap to turn OFF when finished
using it.
Using Your Air Purifier
01 03 05 07
09 11 13 15
17 19 21 23
25 27
02 04 06
08 10 12 14
16 18 20 22
24 26 28 30 32
Replacing the HEPA Filter
Tap to activate Sleep Mode.
When Sleep Mode is enabled, the air purifier will run quietly under lowest possible fan speed,
making it ideal for use while sleeping.
Tap repeatedly to cycle through the adjustable fan speeds: 1, 2, and 3 (Low, Medium, and High).
When adjusting the fan speed under Auto or Sleep Mode, the Auto or Sleep Mode will be
exited automatically.
Tap repeatedly to select the desired auto off time (1, 2, 4 or 8 hours).
When time reaches zero, the air purifier will go into standby mode.
To cancel, tap repeatedly to select 0 hour.
Press and hold for 3 seconds to turn on or off the Lock function.
Sleep Mode
Fan Speed Control
Auto OFF Timer
Child Lock
Indicator ON
Indicator ON
Indicator ON
Indicator ON
1will light up as a reminder to change
the HEPA Filter.
2Unplug the air purifier. Remove the old
HEPA Filter and properly dispose of it.
3Replace with a new one. Install the filters
and air inlet grill back.
4Plug in and tap to turn on the air purifier.
5Press and hold for 3 seconds to reset the
HEPA Filter.
Note:
• Important: Always make sure the air purifier is turned off and unplugged before
replacing the filter.
• It is recommended to replace the HEPA filter every 6 to 8 months (depending on the
frequency of use and air quality).
Using Your Air Purifier
01 03 05 07
09 11 13 15
17 19 21 23
25 27
02 04 06
08 10 12 14
16 18 20 22
24 26 28 30 32
Replacing the HEPA Filter
Tap to activate Sleep Mode.
When Sleep Mode is enabled, the air purifier will run quietly under lowest possible fan speed,
making it ideal for use while sleeping.
Tap repeatedly to cycle through the adjustable fan speeds: 1, 2, and 3 (Low, Medium, and High).
When adjusting the fan speed under Auto or Sleep Mode, the Auto or Sleep Mode will be
exited automatically.
Tap repeatedly to select the desired auto off time (1, 2, 4 or 8 hours).
When time reaches zero, the air purifier will go into standby mode.
To cancel, tap repeatedly to select 0 hour.
Press and hold for 3 seconds to turn on or off the Lock function.
Sleep Mode
Fan Speed Control
Auto OFF Timer
Child Lock
Indicator ON
Indicator ON
Indicator ON
Indicator ON
1will light up as a reminder to change
the HEPA Filter.
2Unplug the air purifier. Remove the old
HEPA Filter and properly dispose of it.
3Replace with a new one. Install the filters
and air inlet grill back.
4Plug in and tap to turn on the air purifier.
5Press and hold for 3 seconds to reset the
HEPA Filter.
Note:
• Important: Always make sure the air purifier is turned off and unplugged before
replacing the filter.
• It is recommended to replace the HEPA filter every 6 to 8 months (depending on the
frequency of use and air quality).
Using Your Air Purifier
01 03 05 07
09 11 13 15
17 19 21 23
25 27
02 04 06
08 10 12 14
16 18 20 22
24 26 28 30 32
Important: Always make sure the air purifier is turned off and unplugged before cleaning.
Outer Surface
Wipe with a soft, dry cloth. If necessary, wipe with a damp cloth, then
immediately dry.
Air Inlet Grill
Open air inlet grill, vacuum up dust with a vacuum cleaner or wipe it with a cloth.
Air Outlet Grill
Remove air outlet grill, vacuum up dust with a vacuum cleaner or wipe it with a cloth.
Cleaning and Maintenance
Cleaning the Air Purifier Body
Cleaning the Pre-Filter
Note:
• DO NOT stick any foreign objects or your fingers inside of the unit.
• Never immerse the air purifier in water and never allow water to drip into the motor
housing.
• For storage, you may leave the unit covered to protect it from dust. Store it in a cool,
dry location.
1Unplug the air purifier. Take out the
Pre-Filter.
2Vacuum the dust or wipe it with a cloth.
3For heavy dust, soak with diluted common
kitchen detergents for 10 minutes, and
then clean.
4Dry the Pre-Filter.
5Install the Pre-Filter and air inlet grill back.
Note:
• It is recommended to clean the Pre-Filter at least once every two weeks. More frequent
cleaning may be required depending on frequency of use and air quality.
• DO NOT clean with abrasive chemicals or flammable cleaning agents.
Cleaning and Maintenance
01 03 05 07
09 11 13 15
17 19 21 23
25 27
02 04 06
08 10 12 14
16 18 20 22
24 26 28 30 32
Important: Always make sure the air purifier is turned off and unplugged before cleaning.
Outer Surface
Wipe with a soft, dry cloth. If necessary, wipe with a damp cloth, then
immediately dry.
Air Inlet Grill
Open air inlet grill, vacuum up dust with a vacuum cleaner or wipe it with a cloth.
Air Outlet Grill
Remove air outlet grill, vacuum up dust with a vacuum cleaner or wipe it with a cloth.
Cleaning and Maintenance
Cleaning the Air Purifier Body
Cleaning the Pre-Filter
Note:
• DO NOT stick any foreign objects or your fingers inside of the unit.
• Never immerse the air purifier in water and never allow water to drip into the motor
housing.
• For storage, you may leave the unit covered to protect it from dust. Store it in a cool,
dry location.
1Unplug the air purifier. Take out the
Pre-Filter.
2Vacuum the dust or wipe it with a cloth.
3For heavy dust, soak with diluted common
kitchen detergents for 10 minutes, and
then clean.
4Dry the Pre-Filter.
5Install the Pre-Filter and air inlet grill back.
Note:
• It is recommended to clean the Pre-Filter at least once every two weeks. More frequent
cleaning may be required depending on frequency of use and air quality.
• DO NOT clean with abrasive chemicals or flammable cleaning agents.
Cleaning and Maintenance
01 03 05 07
09 11 13 15
17 19 21 23
25 27
02 04 06
08 10 12 14
16 18 20 22
24 26 28 30 32
Poor air purification
quality
Excessive noise
Producing an
unpleasant odor
Press Fan Speed Button to
adjust the fan speed.
Remove the filter from its
packaging before use.
Replace the filter.
Remove objects blocking
air intake or outlet.
Properly place the filter
(see Replacing the HEPA
Filter).
Filter is not properly placed
inside the housing.
Filter is dirty and cannot
produce fresh air anymore.
Remove the filter from its
packaging before use.
Place the unit on a level
and flat place.
Immediately discontinue
use and contact TaoTron-
ics Support Team. DO
NOT attempt to open the
air purifier.
Not enough free space
around the unit.
Room size exceeds the
expected size the unit covers.
Air intake or outlet is blocked.
Filter packaging has not been
removed.
Foreign objects inside the
unit.
Unit is placed on an uneven
surface.
Filter is dirty and cannot
produce fresh air any more.
Select the right air purifier
as per the actual room size.
Leave 15 in / 38 cm of
clearance for proper air flow.
Replace the filter (see
Replacing the HEPA Filter).
Replace the filter (see
Replacing the HEPA Filter).
Replace the filter, and move
the air purifier to a room
where the relative humidity
is less than 85% RH.
High humidity levels have caused
mildew to grow on the filter.
Troubleshooting
Error Codes on
LED Display
Filter Change
Indicator does not
turn off
Disassembly Protection
Properly install all parts
(Filters and Air Inlet Grille)
Contact TaoTronics
Support Team.
Connect the plug to a
powered electrical outlet.
Try plugging the air
purifier into a different
outlet.
Possible Causes Solution
Sensor Failure
Abnormal Fan Speed
The air purifier has been reset
incorrectly.
Unit is not plugged in or the
power socket is not switched
Power socket is not working
properly.
Immediately stop using
and contact TaoTronics
Support Team.
Power cord is damaged.
Contact TaoTronics
Support Team.
Air purifier is malfunctioning
The following troubleshooting guide addresses the most common problems. If problems persist,
Problem
Contact TaoTronics
Support Team.
Replace the filter and reset
by pressing and holding the
Timer Button for 3 seconds.
Air purifier does not
power on or respond
to button controls
Insufficient air flow Fan speed is on low setting.
Filter packaging has not been
removed.
Not enough free space
around the unit.
Filter is clogged and not
replaced.
Leave 15 in / 38 cm of
clearance for proper air flow.
01 03 05 07
09 11 13 15
17 19 21 23
25 27
02 04 06
08 10 12 14
16 18 20 22
24 26 28 30 32
Poor air purification
quality
Excessive noise
Producing an
unpleasant odor
Press Fan Speed Button to
adjust the fan speed.
Remove the filter from its
packaging before use.
Replace the filter.
Remove objects blocking
air intake or outlet.
Properly place the filter
(see Replacing the HEPA
Filter).
Filter is not properly placed
inside the housing.
Filter is dirty and cannot
produce fresh air anymore.
Remove the filter from its
packaging before use.
Place the unit on a level
and flat place.
Immediately discontinue
use and contact TaoTron-
ics Support Team. DO
NOT attempt to open the
air purifier.
Not enough free space
around the unit.
Room size exceeds the
expected size the unit covers.
Air intake or outlet is blocked.
Filter packaging has not been
removed.
Foreign objects inside the
unit.
Unit is placed on an uneven
surface.
Filter is dirty and cannot
produce fresh air any more.
Select the right air purifier
as per the actual room size.
Leave 15 in / 38 cm of
clearance for proper air flow.
Replace the filter (see
Replacing the HEPA Filter).
Replace the filter (see
Replacing the HEPA Filter).
Replace the filter, and move
the air purifier to a room
where the relative humidity
is less than 85% RH.
High humidity levels have caused
mildew to grow on the filter.
Troubleshooting
Error Codes on
LED Display
Filter Change
Indicator does not
turn off
Disassembly Protection
Properly install all parts
(Filters and Air Inlet Grille)
Contact TaoTronics
Support Team.
Connect the plug to a
powered electrical outlet.
Try plugging the air
purifier into a different
outlet.
Possible Causes Solution
Sensor Failure
Abnormal Fan Speed
The air purifier has been reset
incorrectly.
Unit is not plugged in or the
power socket is not switched
Power socket is not working
properly.
Immediately stop using
and contact TaoTronics
Support Team.
Power cord is damaged.
Contact TaoTronics
Support Team.
Air purifier is malfunctioning
The following troubleshooting guide addresses the most common problems. If problems persist,
Problem
Contact TaoTronics
Support Team.
Replace the filter and reset
by pressing and holding the
Timer Button for 3 seconds.
Air purifier does not
power on or respond
to button controls
Insufficient air flow Fan speed is on low setting.
Filter packaging has not been
removed.
Not enough free space
around the unit.
Filter is clogged and not
replaced.
Leave 15 in / 38 cm of
clearance for proper air flow.
01 03 05 07
09 11 13 15
17 19 21 23
25 27
02 04 06
08 10 12 14
16 18 20 22
24 26 28 30 32
TaoTronics
SUPPORT
Warranty and Service
Extend your warranty to 18 months at
taotronics.com/warranty
Date of Purchase
Purchased From
Order ID
Should your product prove defective within the
specified warranty period, or any questions
regarding warranty or service, email us at
support@taotronics.com.
Model
Default Warranty Period
TT-AP003
1 Year
Thanks for choosing TaoTronics Air Purifier. This product is covered with TaoTronics product and
labor warranty for 12 months from the date of its original purchase.
Additional Half-Year Warranty
Extend your warranty to 18 months by registering your new product on our website
taotronics.com/warranty
The warranty will not apply in cases of:
- Accident, misuse, or repairs performed by unauthorized personnel.
- Any unit that has been tampered with or used for commercial purpose.
- Normal wear and tear of wearable parts.
- Use of force, damage caused by external influences.
- Damage caused by non-observance of the User Guide, e.g. connection to an unsuitable mains
supply or non-compliance with the instructions.
- Partially or completely dismantled appliances.
- Defects caused by or resulting from damages from shipping or from repairs, service, or
alteration to the product or any of its parts that have been performed by a repair person not
authorized by TaoTronics.
We can only provide after sales service for products that are sold by TaoTronics or TaoTronics
authorized retailers and distributors. If you have purchased your unit from a different place,
please contact your seller for return and warranty issues.
* Please have your invoice and order ID ready before contacting Customer Support.
01 03 05 07
09 11 13 15
17 19 21 23
25 27
02 04 06
08 10 12 14
16 18 20 22
24 26 28 30 32
TaoTronics
SUPPORT
Warranty and Service
Extend your warranty to 18 months at
taotronics.com/warranty
Date of Purchase
Purchased From
Order ID
Should your product prove defective within the
specified warranty period, or any questions
regarding warranty or service, email us at
Model
Default Warranty Period
TT-AP003
1 Year
Thanks for choosing TaoTronics Air Purifier. This product is covered with TaoTronics product and
labor warranty for 12 months from the date of its original purchase.
Additional Half-Year Warranty
Extend your warranty to 18 months by registering your new product on our website
taotronics.com/warranty
The warranty will not apply in cases of:
- Accident, misuse, or repairs performed by unauthorized personnel.
- Any unit that has been tampered with or used for commercial purpose.
- Normal wear and tear of wearable parts.
- Use of force, damage caused by external influences.
- Damage caused by non-observance of the User Guide, e.g. connection to an unsuitable mains
supply or non-compliance with the instructions.
- Partially or completely dismantled appliances.
- Defects caused by or resulting from damages from shipping or from repairs, service, or
alteration to the product or any of its parts that have been performed by a repair person not
authorized by TaoTronics.
We can only provide after sales service for products that are sold by TaoTronics or TaoTronics
authorized retailers and distributors. If you have purchased your unit from a different place,
please contact your seller for return and warranty issues.
* Please have your invoice and order ID ready before contacting Customer Support.
01 03 05 07
09 11 13 15
17 19 21 23
25 27
02 04 06
08 10 12 14
16 18 20 22
24 26 28 30 32
E-mail:
MANUFACTURER
Manufacturer: Shenzhen NearbyExpress Technology Development Co.,Ltd.
Address: Floor 7, Building E, Galaxy World Phase II, Shenzhen, China
Learn more about the EU Declaration of Conformity:
https://www.taotronics.com/pages/user-manual
Rev_1.1_EN-DE
Model: TT-AP003
Air Purifier
User Guide
Other manuals for TT-AP003
1
Table of contents
Other TaoTronics Air Cleaner manuals
