Target Britanna GCS09062H User manual

hanging egg chair
style # GCS09062H
dpci # 009000186
>>assembly instructions TM
Britanna

Congratulations on your latest Target purchase.
Now what? Don't start sweating over this box of parts. This will be easy. We did the hard work for you.
All you need to do is follow our simple instructions and you'll be on your way to transforming your patio in no time.
Good luck – though we're confident you won't need it.
ATTENTION:
This Chair is not intended for use during any kind of inclement weather and the manufacturer is not
and can not beheld responsible for any damages caused as a result of such weather. Weather-related
damage, or damage as a result of the Chair not being stored properly when not in use is not the
responsibility of the manufacturer.
During extended periods of non-usage, off season, or in inclement weather (wind, rain, snow, hail,
sleet), freezing conditions and extreme heat, the Chair needs to be stored in a dry sheltered place to
prolong the life and to avoid damage to the Chair.
2
IMPORTANT WARNING:
Unpack the box on a clean soft level surface and make sure all parts have been included.
To replace missing or damaged parts please call 855-MYTGTHOME (855-698-4846) during 7am - 7pm CST M-F, and 8am - 5pm CST Saturday.
WEIGHT LIMIT 250 LBS MAXIMUM.
Chair is intended to be used by one person at a time.
Chair and stand must be used with all provided parts. Ensure that all parts are
installed according to instructions and inspected for damage before use.
Ensure that all bolts and hardware are securely tightened and installed before use.
Always inspect your chair, hardware, and stand for damage before use.
Never place infants or pets in the chair.
Never allow young children to use chair without adult supervision.
Do not jump, stand, or twist in chair.
Chair and stand are designed for minimal swing motion. Use care when getting in and
out of chair. If using stand, ensure that chair is facing forward and do not cause chair
to swing outside base area of stand.
Stand must be used with attached safety rope, included with product.
Do not climb on support pole.
Use on even-flat surfaces only.
This hanging egg chair is not a toy.
.
WARNING-TO AVOID RISK OF FALLING

WARRANTY:
This Chair comes with a one year limited warranty against original manufacture defects. If you experience
trouble with your chair, please call the customer service number below.
3
Target Corporation
Toll Free at: 855-MYTGTHOME (855-698-4846) during 7am - 7pm CST M-F, and 8am - 5pm CST Saturday.
Code: Yotrio 2020
before you begin
1. Check for damage or missing parts. Call to order missing supplies.
2. Use the carton as a working surface to prevent product damage during assembly.
3. Gather all tools prior to assembly.
855-MYTGTHOME (855-698-4846)

table of contents
introduction
hardware
parts list
assembly
2-3
5
6
7-13
QUESTIONS?
4Please call 855-MYTGTHOME (855-698-4846) parts and service. For faster service, have th e style number and DPCI number ready when calling.

hardware
5
(Part H)×2
M8*15mm bolt
(Part V)×1
wrench
(Part U)×1
allen wrench
(Part I)×7
M8*20mm bolt with washer
(Part J)×4
M6*45mm bolt with washer
(Part G)×2
M8*55mm bolt
(Part L)×4
M6 washer
(Part K)×2
M6*15mm bolt with washer
(Part M)×4
M6 nut
(Part N)×9
M8 washer
(Part R)×2
plastic muffler
(Part O)×2
M8 spring washer
(Part P)×9
M8 nut
(Part Q)×1
hook
(Part S)×2
post plastic part
(Part T)×1
connection part

ITEM DESCRIPTION QUANTITY
1
A
6
left base
B right base 1
1
Clower hanging bar
1
Dupper hanging bar
1
Eback frame
1
Fseat frame
1
Qhook
Rplastic mulffer 2
A
B
C
D
R
E
F
R
Q
S
T
Spost plastic part 2
Tconnection part 1
S

7
step 01:
ATTENTION: To avoid damage to your new patio furniture, please
use either the carton or another soft surface such as carpet as a
working surface to prevent product damage during assembly.
1. Connect left base (A) and right base (B) by using post plastic part (S) and connection part (T).
Secure with M6*15mm bolt with washer (K) using allen wrench (U).
2. Lining up the bolt holes on the end of the left base (A) with the corresponding bolt
holes on the right base (B).
(Part K)×2
M6*15mm bolt with washer
(Part N)×3
M8 washer
(Part I)×3
M8*20mm bolt with washer
(Part P)×3
M8 nut
(Part T)×1
connection part
(Part U)×1
allen wrench
1. 2.
A
B
T
K
N
P
T
I
(Part V)×1
wrench
Do not completely tighten screws until all screws are in place.
3. Secure with M8*20mm bolt with washer (I), M8 washer (N) and M8 nut (P) using
allen wrench (U) and wrench (V).
S
S
(Part S)×1
post plastic part

step 02:
1. Attach the lower hanging bar (C) to the left base (A) and right base (B) by lining up
the bolt holes on the lower hanging bar (C) with the corresponding bolt holes on the
left base (A) and right base (B).
2. Secure with M8*20mm bolt with washer (I), M8 washer (N) and M8 nut (P) using allen
wrench (U) and wrench (V).
(Part I)×4
M8*20mm bolt with washer
(Part N)×6
M8 washer
(Part H)×2
M8*15mm bolt
(Part O)×2
M8 spring washer
(Part U)×1
allen wrench
(Part V)×1
wrench
Do not completely tighten screws until all screws are in place.
3. Secure with M8*15mm bolt (H), M8 spring washer (O) and M8 washer (N) using allen
wrench (U).
8
(Part P)×4
M8 nut
A
B
C
P
P
N
N
N
O
O
I
H

9
step 03:
1. Connect upper hanging bar (D) and lower hanging bar (C) by using post plastic part (S).
Secure with M8*55mm bolt (G), M8 washer (N) and M8 nut (P) using allen wrench (U)
and wrench (V).
2. Attach the plastic muffler (R) to the hook of upper hanging bar (D).
(Part N)×2
M8 washer
(Part P)×2
M8 nut
(Part G)×2
M8*55mm bolt
(Part U)×1
allen wrench
1. 2.
(Part V)×1
wrench
Do not completely tighten screws until all screws are in place.
3.
(Part S)×1
post plastic part
(Part R)×1
plastic muffler
C
D
R
R
N
P
S
G
P
N
G

step 04:
1. Attach the back frame (E) to the seat frame (F) by lining up the bolt holes on the
back frame (E) with the corresponding bolt holes on the seat frame (F).
2. Secure with M6*45mm bolt with washer (J), M6 washer (L) and M6 nut (M) using
allen wrench (U) and wrench (V).
(Part L)×4
M6 washer
(Part M)×4
M6 nut
(Part J)×4
M6*45mm bolt with washer
(Part R)×1
plastic muffler
(Part U)×1
allen wrench
(Part V)×1
wrench
Do not completely tighten screws until all screws are in place.
3. Attach the plastic muffler (R) to the hook of back frame (E).
10
1. 2. 3.
E
F
E
F
J
ML
R
R