Target Fairmont User manual

8’ x 8’ FT Steel Gazebo with Curtains
style # GFS20200B
dpci # 009050059
>>assembly instructions TM
Fairmont

ATTENTION:
This Gazebo is not intended for use during any kind of inclement weather and the manufacturer is not,
and can not be held responsible for any damages caused as a result of such weather. Weather-related
damage, or damage as a result of the Gazebo not being stored properly when not in use, is not the responsibility of the manufacturer.
During extended periods of non-usage, off season, or in inclement weather (wind, rain, snow, hail,
sleet), freezing conditions and extreme heat, the Gazebo needs to be stored in a dry, sheltered place to prolong the life and to avoid
damage to the Gazebo.
IMPORTANT WARNING:
Unpack the box on a clean soft level surface and make s ure all parts have been included.
To replace missing or damaged parts please call 855-MYTGTHOME (855-698-4846) during 7am - 7pm CST M-F, and 8am - 5pm CST Saturday.
Congratulations on your latest Target purchase.
Now what? Don't start sweating over this box of parts. This will be easy. We did the hard work for you.
All you need to do is follow our simple instructions and you'll be on your way to transforming your patio in no time.
Good luck – though we're confident you won't need it.

WARRANTY:
This Gazebo comes with a one year limited warranty against original manufacture defects. If you experience
trouble with your Gazebo, please call the customer service number below.
3
Target Corporation
Toll Free at: 855-MYTGTHOME (855-698-4846) during 7am - 7pm CST M-F, and 8am - 5pm CST Saturday.
Code: Yotrio 2020
before you begin
1. Check for damage or missing parts. Call 855-MYTGTHOME (855-698-4846) to order missing supplies.
2. Use the carton as a working surface to prevent product damage during assembly.
3. Gather all tools prior to assembly.
4. This Gazebo is heavy, may require two to four adults for safe assembly.

table of contents
introduction
hardware
parts list
assembly
2-3
5
6
7-16
QUESTIONS?
4Please call 855-MYTGTHOME (855-698-4846) parts and service. For faster service, have th e style number and DPCI number ready when calling.

hardware
5
(Part O)×28 (Part P)×16 (Part R)×12
(Part T)×2
M6*15mm bolt with washer nut
allen wrench
(Part S)×16
ground spike
(Part U)×1
wrench
(Part Q)×4
M6*55mm bolt with washer
(Part V)×4
plastic washer
M6*30mm bolt with washer

ITEM DESCRIPTION QUANTITY
beam
4
4
A
B
C corner inclined tube
6
4
post leg
Dmiddle inclined tube 4
E
F
G
H
I
J
shade rod 4
top connector 1
U-shaped part 1 4
U-shaped part 2 4
post base 4
tube connector 8
K
L
M
N
connection buckle 32
top canopy 1
4
1canopy
curtain
A
A
A
A
B
B
B
B
C
C
C
C
D
D
D
E
E
E
E
F
G
G
G
G
H
H
H
H
I
I
I
I
J
J
J
J
J
J
J
K
N
M
L
V
V
V
V

7
step 01:
(Part O)×12
M6*15mm bolt with washer
(Part T)×1
allen wrench
Do not completely tighten screws until all screws are in place.
ATTENTION: To avoid damage to your new gazebo, please
use either the carton or another soft surface such as carpet as a
working surface to prevent product damage during assembly.
1. Attach the U-shaped part 1 (G) to the post leg (A), secure with M6*15mm bolt with washer (O) using the allen wrench (T).
2. Insert the post base (I) into the post leg (A), secure with M6*15mm bolt with washer (O) using the allen wrench (T).
1. 2.
A
A
A
I
I
O
O
O
G
3.
G
3. Repeat above steps until 4 U-shaped part 1 (G) and post base (I) are secured to the post leg (A).

8
step 02:
(Part O)×16
M6*15mm bolt with washer
Do not completely tighten screws until all screws are in place.
(Part T)×1
allen wrench
1. Attach the beam (B) to the post leg (A), secure with M6*15mm bolt with washer (O) using allen wrench (T).
2. Repeat above step until the 4 beam (B) are secured to the post leg (A).
A
A
A
A
A
B
BB
B
B
O

9
step 03:
Do not completely tighten screws until all screws are in place.
J
JJ
J
E
E
1. Attach the tube connector (J) to the shade rod (E).
2. Repeat above step until the 8 tube connectors (J) are attached
to the shade rod (E).

10
step 04:
Do not completely tighten screws until all screws are in place.
1. Attach the tube connector (J) to the beam (B), secure with M6*30mm bolt with washer (P) using the allen wrench (T).
2. Attach the U-shaped part 2 (H) to the beam (B), secure with M6*55mm bolt with washer (Q), plastic washer (V) and nut (R)
using allen wrench (T) and wrench (U).
3. Repeat above steps until 4 shade rods (E) and U-shaped part 2 (H) are secured with the beam (B).
B
B
B B
BB
B
H
H
H
H
E
E
E
E
JJ
R
P
P
V
Q
2.
1.
(Part P)×8
M6*30mm bolt with washer
(Part T)×1
allen wrench
(Part R)×4
nut
(Part Q)×4
M6*55mm bolt with washer
(Part U)×1
wrench
(Part V)×4
plastic washer

11
step 05:
Do not completely tighten screws until all screws are in place.
C
C
C
C
C
C
C
C
D
D
D
D
D
D
D
D
F
F
1. Attach the corner inclined tube (C) and middle inclined tube (D) to the top connector (F).

12
step 06:
Do not completely tighten screws until all screws are in place.
1. Attach the corner inclined tube (C) to U-shaped part 1 (G), secure with M6*30mm bolt with washer (P) and nut (R) using allen wrench (T) and wrench (U).
2. Attach the middle inclined tube (D) to U-shaped part 2 (H), secure with M6*30mm bolt with washer (P) and nut (R) using allen wrench (T) and wrench (U).
3. Repeat above steps until the 4 corner inclined tubes (C) are secured to the U-shaped part 1 (G), and the 4 middle inclined tubes (D) are secured to the U-shaped
part 2 (H).
1. 2.
C
C
C
C
C
D
D
D
D
P
P
G
R
R
H
(Part P)×8 (Part R)×8
M6*30mm bolt with washer nut
(Part U)×1
wrench
(Part T)×1
allen wrench

13
step 07:
Do not completely tighten screws until all screws are in place.
1. Attach the canopy (M) and top canopy (L) on the top.
M
L

14
step 08:
Do not completely tighten screws until all screws are in place.
1. Slip the corner inclined tube (C) and middle inclined tube (D) into
the top canopy (L) and canopy (M).
2.
1. 3.
L
M
C
D
M

15
step 9:
Do not completely tighten screws until all screws are in place.
1. Hanging the curtain (N) to the beam (B) by using the connection buckle (K).
2. Insert the ground spikes (S) through the post base (I) and into ground.
2.
1.
A
A
A
A
NN
N
N
I
I
I
I
S
EK
(Part S)×16
ground spike

16
step 10:
1. Tighten all bolts. Ensure all connections are secure
before use.
You are now ready to enjoy your new gazebo.

TM
2020 Target. The Bullseye Design is a trademark of Target Brands Inc. All rights reserved.