Tascam DR-22WL User manual

D01244520D
DR-22WL
Linear PCM Recorder
REFERENCE MANUAL

2 TASCAM DR-22WL
Contents
1 – Introduction ..............................................4
Features..................................................................................4
Conventions used in this manual..................................4
About microSD cards.........................................................4
Precautions..................................................................... 4
2 – Names and functions of parts ..................5
Top panel ...............................................................................5
Front panel............................................................................5
Left side panel......................................................................6
Right side panel................................................................... 6
Bottom panel........................................................................6
Home Screen ........................................................................ 7
Recording Screen................................................................ 7
Menu item list.......................................................................9
Using menus......................................................................... 9
Basic operations ..................................................................9
3 – Preparation..............................................10
Powering the unit .............................................................10
Power sources .............................................................10
Using AA size batteries.............................................10
Using an AC adapter (sold separately)................10
Using USB bus power................................................10
Turning the power on and off (standby mode) .....11
Starting up the unit................................................... 11
Shutting down (standby mode)............................11
Resume function ........................................................ 11
Selecting the language................................................... 11
If you accidentally select the wrong language .. 11
Setting the date/time......................................................11
Inserting and removing microSD cards ....................12
Inserting the SD card ................................................12
Removing the card ....................................................12
Setup the microSD card for use ...................................12
Turning the built-in speaker on/off ............................13
Connecting a monitor device.......................................13
Adjusting the playback volume...................................13
Input settings .....................................................................14
Recording with the built-in microphone...........14
Recording with an external microphone (MIC IN)... 14
Recording from an external device (LINE IN) ...14
4 – Recording ................................................15
Selecting the recording mode .....................................15
Recording.............................................................................15
Scene recording mode....................................................15
Selecting a folder to store files ....................................16
Recording format settings (FORMAT/SAMPLE/TYPE) ..16
Adjusting the input level................................................17
Setting the peak hold function.............................17
Setting the Low Cut Filter ..............................................18
Using the level control function ..................................18
Switching files during recording (track increment) ..19
Manual track increment during recording........19
Automatic track increment at specified time ..19
Automatic recording (AUTO REC)...............................19
Start recording from slightly before pressing record
(PRE REC) ...............................................................................20
Using the SELF TIMER for recording...........................20
Recording in two formats (DUAL FORMAT).............21
Mixing the input sound to the playback for record-
ing (overdubbing).............................................................21
Select files for overdubbing with an input sound .. 21
Start overdubbing......................................................21
Create cue marks during recording............................22
Manual cue marking during recording ..............22
Add cue marks automatically to recording ......22
Adding marks automatically when the PEAK
indicator lights ............................................................23
Recording duration ..........................................................24
5 – Using files and folders (browse screen) .25
Navigating in the browse screen.................................25
Icon display on the browse screen .............................25
File operations ...................................................................25
Protecting files ............................................................26
Clearing all marks.......................................................26
Folder operations..............................................................26
Deleting empty folders............................................27
Moving up a folder level .........................................27
Creating a new folder......................................................27
6 – Playback...................................................28
Playback................................................................................28
Pausing/stopping playback....................................28
Rewinding and fast-forwarding (search) ...........28
Selecting a playback file (skip) .....................................28
Special playback (practice mode) ...............................28
Loop playback .............................................................28
Changing the playback speed (VSA)...................29
Changing keys.............................................................29
Adding marks manually during playback................29
Clearing specified marks................................................29
Moving to the cue mark position................................29
7– Useful functions .......................................31
Dividing a file......................................................................31
Dividing the selected file (DIVIDE).......................31
Dividing the selected file automatically (AUTO
DIVIDE) ...........................................................................31
Reverb function.................................................................32
Setting the reverb function....................................32
Reverb pre-set list ......................................................32
Setting the XRI information recording function ..32
Viewing XRI information..........................................33

TASCAM DR-22WL 3
Contents
Deleting XRI information.........................................33
Metronome function .......................................................33
8 – Connecting with a computer..................34
Transferring files to a computer ..................................34
Transferring files from a computer.............................34
Disconnecting from a computer.................................34
9 – Using Wi-Fi...............................................35
Connect the DR-22WL and smart phone via Wi-Fi.. 35
How to download and install the exclusive
application (DR CONTROL).....................................35
Selecting the Wi-Fi mode........................................35
Connecting the unit directly to external devices
(smartphones, tablets and computers) by Wi-Fi
(TO DEVICE mode) ......................................................35
Connecting the DR-22WL to a smart phone via
Wi-Fi for the first time...............................................35
Connecting the DR-22WL to a smart phone via
Wi-Fi (from second time onward) ........................36
Connecting the unit to external devices (smart-
phones, tablets and computers) by Wi-Fi (VIA
ROUTER mode) ............................................................37
Launching DR CONTROL .........................................38
Connecting this unit to a computer by Wi-Fi..........39
Downloading and installing the TASCAM DR
FILE TRANSFER software..........................................39
Connecting the unit directly to a computer by
Wi-Fi (TO DEVICE mode) ..........................................39
Connecting this unit to a computer by Wi-Fi after
the first time .......................................................................40
10 – Settings and Information .....................41
View information (INFORMATION)..............................41
File information screen (FILE INFO)......................41
Card information screen (CARD INFO)................41
System information screen (VERSION)...............41
System Settings (SETUP).................................................42
Auto power save function setting .......................42
Backlight setting.........................................................42
Adjusting the display contrast...............................42
Battery type settings ................................................42
Setting the language................................................42
Restoring the DR-22WL to factory settings ......42
Formatting the microSD card................................42
Setting the file name type......................................43
11 – Messages................................................44
12 – Troubleshooting....................................45
13 – Specifications ........................................46
Rating ....................................................................................46
Input/output ratings........................................................46
Analog audio input and output ratings.............46
Control input/output ratings .................................46
Audio performance..........................................................46
Wi-Fi.......................................................................................46
General .................................................................................47
Dimensional drawings ....................................................47
Trademarks and copyrights
• TASCAM is a trademark of TEAC CORPORATION, registered
in the U.S. and other countries.
• SDXC Logo is a trademark of SD-3C, LLC.
• Supply of this product does not convey a license nor imply
any right to distribute MPEG Layer-3 compliant content
created with this product in revenue-generating broadcast
systems (terrestrial, satellite, cable and/or other distribution
channels), streaming applications (via Internet, intranets
and/or other networks), other content distribution systems
(pay-audio or audio-on-demand applications and the like)
or on physical media (compact discs, digital versatile discs,
semiconductor chips, hard drives, memory cards and the
like). An independent license for such use is required. For
details, please visit http://mp3licensing.com.
• MPEG Layer-3 audio coding technology licensed from
Fraunhofer IIS and Thomson.
• Wi-Fi is a trademark of Wi-Fi Alliance. The Wi-Fi CERTIFIED
Logo is a certification mark of Wi-Fi Alliance.
• Microsoft, Windows and Windows Vista are either registered
trademarks or trademarks of Microsoft Corporation in the
United States and/or other countries.
• Mac is a trademarks of Apple Inc.
• IOS is a trademark or registered tradmark of Cisco in the U.S.
and other countries and is used under license.
• App Store is a service mark of Apple Inc.
• Google Play and Android are trademarks of Google inc.
• Blackfin® and the Blackfin logo are registered trademarks of
Analog Devices, Inc.
• Other company names, product names and logos in this
document are the trademarks or registered trademarks of
their respective owners.

4 TASCAM DR-22WL
1 – Introduction
Features
• Compact audio recorder that uses microSD/microSDHC/
microSDXC cards as recording media
• Built-in with high performance directional stereo
microphones in XY positions
• Built-in Wi-Fi feature to use smartphone as remote control,
transfer files from the PCM recorder, and playback audio
• Scene dial allows for easy recording
• Two overdubbing modes for sound dubbing
• Practice mode with features useful for instrument practice,
such as I/O loop for repeated playback, VSA to adjust
playback speed without changing the pitch, key-change
and fine-tune to adjust the pitch
• 44.1/48/96 kHz, 16/24-bit, linear PCM (WAV/BWF format)
recording possible
• 32–320 kbps MP3 format recording possible (compatible
with ID3 tag v2.4)
• Overdubbing allows playback and input signals to be mixed
and recorded together as a new file
• Built-in 0.3 W monaural output speaker
• Built-in reverb function can be used during recording and
playback
• Automatic recording function starts recording
automatically when a set sound input level is detected
• Track incrementing function allows a recording to be split
by creating a new file when desired
• Pre-recording function allows the unit to record the
2seconds of sound before recording is activated
• Peak reduction function is available to reduce the level
automatically in case of excessively large input
• Limiter function is available to reduce the level
automatically in case of excessively large input
• Low cut filter reduces low-frequency noise
• SELF TIMER function to start recording after a set period of
time
• DIVIDE function allows files to be split where desired (only
for WAV files)
• MARK function convenient for moving to specific locations
• File name format can be set to use a user-defined word or
the date
• Resume function memorizes the playback position before
the unit is turned off
• 3.5mm (1/8”) jack for external stereo microphone input
(provides plug-in power) or external stereo line input
• 3.5mm (1/8”) line/headphones output jack
• 128 x 128 pixel LCD with backlight
• Micro-B type USB 2.0 port
• Operates on 2 AA batteries, AC adapter (sold separately:
TASCAM PS-P520E), or USB bus power
• Tripod attachment screw-hole built into unit
• USB cable included
This product has a Blackfin® 16/32-bit embedded processor
made by Analog Devices, Inc. This processor controls digital
signal processing.
Inclusion of this Blackfin® processor in the product increases
its performance and reduces its power consumption.
Conventions used in this manual
The following conventions are used in this manual:
• Buttons, connectors and other physical parts of this unit are
written using a bold font like this: MENU button.
• When we show messages, for example, that appears on the
unit’s display, the typeface looks like this: INPUT.
• microSD, microSDHC and microSDXC memory cards are
called “microSD cards”.
• Information shown on the computer display is written like
this “OK”.
• The selected folder is indicated as the“current folder”.
• Computer or portable audio devices that are connected via
Wi-Fi with the DR-22WL are indicated as the“Wi-Fi device”.
• Additional information is provided as necessary in tips,
notes and cautions
TIP
These are tips about how to use the unit.
NOTE
These include additional explanations and special cases.
CAUTION
Failure to follow these instructions could result in injury,
equipment damage or lost data, for example.
About microSD cards
The DR-22WL uses microSD cards for recording and playback.
Memory cards that you can use with the DR-22WL are microSD
cards of 64 MB to 2 GB, microSDHC cards of 4GB to 32GB, and
microSDXC cards of 48GB to 128GB.
A list of SD cards that have been confirmed for use with this unit
can be found on our web site. Please access to a product page of
this product from the TEAC Global Site (http://teac-global.com)
to find the list or contact the TASCAM customer support service.
Precautions
microSD cards are precision devices. Please refer to the below
when using memory cards to prevent memory and/or card
damage:
• Do not leave a memory card in extremely hot or cold places
• Do not leave a memory card in extremely humid places
• Do not spill any liquids on the memory card
• Do not bend the card or subject it to any excessive force
• Do not subject the card to any physical shock
• Do not remove the card while the unit is accessing data, or
recording, playing, or making data transfer
• Always store the memory card in a case

TASCAM DR-22WL 5
2 – Names and functions of parts
Top panel
1 Built-in stereo microphone
This is an XY directional stereo electret condenser
microphone.
The built-in microphone becomes inactive when an external
microphone or external input is connected to the MIC/EXT
IN jack on the right-side panel.
2 PEAK indicator
This will light in red immediately before the input noise
increases to a distortion level (−2dB).
3 −12dB indicator
This will light in green when the input noise exceeds the
−12dB level.
4 Display
Displays a variety of information.
5 Function buttons
Function of individual buttons changes according to what is
shown on display.
The displayed icon at the bottom of the screen indicates the
current function.
NOTE
For your convenience, this manual indicates the four
function buttons as F1, F2, F3, and F4 starting from the left.
6 Scene dial
Use this dial to change the unit setting according to the
scene. (See“Scene recording mode” on page 15.)
7 /MENU/8button
To display the MENU screen, press this button in home
screen.
To return to the home screen, press this button in any screen
display.
Press this button during recording to stop recording. Press
this button during playback or recording standby to pause
or stop (depending on the position in the file).
8 .Fast rewind button
Press this button while in play or stop mode to return to the
beginning of a track.
Press and hold this button to search backwards.
When the MARK SKIP MODE on the menu screen TOOL page
is not set to OFF, press this button while pressing the F2
button to move to the previous mark. (See “Moving to the
cue mark position” on page 29.)
9 Built-in mono speaker
Use this built-in speaker to listen to recordings.
No sound will play when:
• In recording standby
• Headphone is connected
• In recording mode
• Speaker output setting is turned off
0 RECORD button/RECORD indicator
When you press this button during stop mode, the RECORD
indicator (around RECORD button) flashes and the DR-22WL
will go into recording standby mode.
When you press this button during the recording standby
mode, the RECORD indicator lights and the DR-22WL starts
recording.
When you press this button during recording, the RECORD
indicator flashes.
When the scene dial is set to , press when stopped to
start recording.
q PLAY button
When the home screen is open and playback is stopped,
press this button to start playback.
When you select a file or folder in browse screen and press
the PLAY button, the unit will return to the home screen and
start playing the selected file or folder from the beginning.
w /Fast forward button
Press this button in playback or stop mode to skip to the
next track.
Press and hold this button for fast forward search.
When the MARK SKIP MODE on the menu screen TOOL page
is not set to OFF, press this button while pressing the F2
button to move to the next mark. (See “Moving to the cue
mark position” on page 29.)
e Wi-Fi button
Use this button to turn on/off the Wi-Fi function.
Front panel
r Strap holder
A strap can be attached to this holder.
t Wi-Fi indicator
This indicator lights while the Wi-Fi module is in access.
y INPUT LEVEL volume
Turn this dial to adjust the input level.
The input level setting will pop-up on display when making
an adjustment.

6 TASCAM DR-22WL
2 – Names and functions of parts
Left side panel
u/LINE OUT jack
A headphone or a line input jack of an external device (via
stereo mini-jack cable) can be connected to this jack.
i OUTPUT LEVEL (+/−) buttons
These buttons adjust the output sound level of the built-in
speaker or the /LINE OUT jack.
Volume level will pop-up on the bottom of the display while
making adjustment.
o HOLD/ switch
To turn the power on/off, slide and hold the switch towards
the icon.
When you slide the switch towards the HOLD side, all the
functions of the buttons are locked.
Right side panel
p USB port
Use the supplied USB cable to connect the DR-22WL with a
computer. (See “8 – Connecting with a computer” on page
34.)
Power can be supplied by using this USB cable or from an AC
adapter (sold separately: PS-P520E).
CAUTION
Connect the DR-22WL directly be connected directly with
the computer, not through a USB hub.
a microSD card slot
Insert or remove a microSD card.
s MIC/EXT IN jack
Connect an external stereo microphone or external input to
this jack. It is compatible with plug-in power.
The built-in microphone is disable when an external
microphone is connected to the MIC/EXT IN jack.
Bottom panel
d Tripod attachment screw-hole (1/4 inch)
A tripod can be attached to the DR-22WL.
CAUTION
• Ensure the tripod or microphone stand screws are securely
fastened to prevent the unit from falling off.
• When attaching this unit to a tripod or microphone stand,
ensure to place it on a level surface.
f Battery compartment cover
g Battery case
Insert batteries (two AA size) in this compartment to power
the unit. (See “Using AA size batteries”on page 10.)

TASCAM DR-22WL 7
2 – Names and functions of parts
Home Screen
1 Playback file type message
Format type, sampling rate, bit rate, stereo/mono setting of
the playback file are shown.
2 Plug-in power on/off message
The plug-in power status (on/off) is displayed in icon view.
(See “Recording with an external microphone (MIC IN)”on
page 14.)
Icon On/off status
Blank Plug-in power function off
Plug-in power function on
3 Monitor output message
: output from built-in speaker
: output from headphone
4 Power supply status message
When power is supplied from the batteries, the current
battery level is displayed in bars ( , , ).
When the battery level is low, the will flash and the power
will be switched off (standy mode).
The will be displayed when using either the dedicated
AC adapter (TASCAM PS-P520E; sold separately) or the USB
bus power.
NOTE
When attempting recording or other operations that
consume large amount of power, a warning message of
Battery Low may pop-up.
5 Level meter
Displays the level of the playback sound.
6 Recorder status message
The recording status is indicated in the following icons:
Indicator Meaning
8Stop
9Pause
7Playback
,Fast forward
mRewind
/Skip forward to the beginning of the next file
.Skip backward to the beginning of either the
current or preceding file
7 File name
The name or tag information of the file currently in play is
displayed.
The ID3 tag information is displayed instead when included
in the MP3 file.
NOTE
ID3 tag information contains titles and artist names, which
can be stored in MP3 files.
8 Function buttons status message
Below icons are displayed while in stop or playback mode.
Icon Function
Display browse screen
Mark function (set/clear)
Delete file
9 Peak decibel (dB) message
Displays the maximum playback level in decibel reading per
set amount of time.
0 Elapsed time message
Displays the elapsed time (hours: minutes: seconds) of the
current file.
q Remaining time message
Displays the remaining time (hours: minutes: seconds) of the
current file.
Recording Screen
The below recording screen is displayed in recording or
recording standby mode.
1 Recording mode message
Displays the format, sampling rate, and stereo/mono of the
recording file. (See “Recording format settings (FORMAT/
SAMPLE/TYPE)” on page 16.)
2 Low-cut filter on/off status message
Displays the low-cut filter on/off status.
The message is highlighted when the low-cut filter is set at
40Hz / 80Hz / 120Hz / 220Hz.
Blank: low-cut filter is off
: low-cut filter is on
3 Limiter function on/off message
Displays the limiter function on/off status. (See “Setting the
Low Cut Filter” on page 18.)
Blank: limiter function is off
: limiter function is on
4 Peak reduction function on/off status message
Displays the peak reduction on/off status. (See “Using the
level control function”on page 18.)
Blank: peak reduction function is off
: peak reduction function is on

8 TASCAM DR-22WL
2 – Names and functions of parts
5 Reverb on/off status message
Displays the reverb on/off status.
Icon On/off status
Blank Reverb is off
Reverb is on (Reverb sound added to
input sound)
Reverb is on (Reverb sound added to
output sound)
6 Level meter
Displays the input sound level.
When the AUTO REC function is turned on, the level meter
will display sounds within the level that activates the AUTO
REC function.
7 Prerecording function on/off status
Displays the Prerecording function on/off status. (See “Start
recording from slightly before pressing record (PRE REC)” on
page 20.)
Blank: Prerecording is off
: Prerecording function is on
8 Recording status message
The recording status is indicated in the following icons:
Indicator Meaning
09 Recording standby or recording pause mode
0In recording mode
Begins recording in five seconds
Begins recording in ten seconds
9 Automatic recording function on/off status
Displays the Automatic recording function on/off status.
(See “Automatic recording (AUTO REC)” on page 19.)
Blank: Automatic recording off
: Automatic recording function on
NOTE
is displayed when the scene mode is or .
In this case, level control is automatic.
0Dual format recording function on/off status
This shows whether dual format recording is on or off.
Blank: dual format recording function off
: dual format recording function on
q File name message
Displays the file name automatically assigned to the
recording file.
w Peak decibel (dB) message
Displays the peak input level in decibel reading.
will be displayed when recording is above the peak level
(−2dB or more).
e Elapsed recording time
Displays the elapsed recording time of a recorded file (hours:
minutes: seconds).
r Remaining recording time
Displays the remaining recording time for the microSD card
(hours: minutes: seconds).
t Function buttons message
The following icons will be displayed while in recording
standby, recording, or recording pause mode:
Icon Function
Self-timer function
Mark function (set mark)
Display input setting screen
Activate the track increment
Clear peak hold

TASCAM DR-22WL 9
2 – Names and functions of parts
Menu item list
Press the /MENU/8button to display the menu screen.
The menu screen consists of four pages each separated by types
of menu items.
REC SETTING: make basic recording settings
TOOL: make function settings useful for playback files
SETUP: make configuration settings for the DR-22WL
INFORMATION: displays file and media information
Menu items are as follows:
Menu item Function Ref. page
REC SETTING
Make recording settings
FORMAT
SAMPLE
TYPE
page 16
PRE REC page 20
AUTO FUNC page 19
DUAL FORMAT page 21
COUNT INIT page 43
PEAK HOLD page 17
TOOL
Make settings for various functions.
MARK SKIP MODE page 29
XRI MODE page 32
DIVIDE page 31
AUTO DIVIDE page 31
REVERB page 32
SPEAKER page 13
METRONOME page 33
SETUP
Make various settings.
MEDIA FORMAT page 42
BACKLIGHT page 42
CONTRAST page 42
Wi-Fi
page 35
page 37
page 39
AUTO PWR SAVE page 42
BATTERY TYPE page 42
DATE/TIME page 11
FILE NAME page 43
INITIALIZE page 42
INFORMATION
View various types of information.
XRI page 33
FILE INFO
page 41CARD INFO
VERSION
Using menus
The following explains the menus, using the display contrast
setting as an example.
1. Press the /MENU/8button to display the menu screen.
2. Press the F1 button to display various menu pages.
SETUP page is selected
3. Use the F2 and F3 buttons to select (highlight) the
item you want to set.
CONTRAST item is selected
4. Press the F4 button to open the parameter display.
5. Use the F2 and F3 buttons to change settings, and
press the F4 button to finalize the setting.
Press the F1 button to cancel a change.
6. Repeat the 2. to 5. steps to set each items.
7. Press the /MENU/8button to return to the home screen.
Basic operations
Use the following buttons to operate the various screens.
/MENU/8button
The menu screen will pop up when you press this button in stop
or pause mode.
To return to the home screen, press this button in any screen
display.

10 TASCAM DR-22WL
3 – Preparation
Powering the unit
Power sources
The DR-22WL operates on two AA batteries, the dedicated AC
adapter (TASCAM PS-P520E; sold separately), or the supplied
USB cable (USB bus power).
Use either alkaline batteries or Ni-MH batteries.
Using AA size batteries
Remove the battery compartment cover on the back of the unit,
insert two AA batteries with the ¥and ^ends in the right
position, and close the cover.
Select the same type of batteries to get an accurate reading of
the remaining battery power and required minimum power for
operation. (See “Battery type settings”on page 42.)
CAUTION
• Do not use Manganese dry cell batteries.
• Ni-MH batteries will not be recharged with this unit; use a
separate battery recharger instead.
• The supplied alkaline batteries are for testing and may not
last long.
Using an AC adapter (sold separately)
Use the supplied USB cable to connect the USB port of the
unit and the dedicated AC adapter (TASCAM PS-P520E; sold
separately) as illustrated below.
AC outlet
micro-B USB plug
TASCAM PS-P520E (sold separately)
Connect the
supplied USB cable
NOTE
When both batteries and the AC adapter are attached to the
unit, power will be supplied from the AC adapter.
CAUTION
• Use only the dedicated AC adapter (TASCAM PS-P520E;
sold separately). The use of another adapter may cause
malfunction, fire or electric shock.
• Noise may occur during microphone recording when the
unit and AC adapter are in close proximity. If noise occurs,
move the AC adapter away from the unit.
Using USB bus power
Use the supplied USB cable to connect the unit and the
computer as illustrated below.
Computer
micro-B USB plug
Connect the
supplied USB cable
USB
When you connect a USB cable while the unit power is on, or
turn on the power after making a connection, the USB SELECT
screen will pop up, prompting the user to select either to
operate the unit with USB bus power or make a USB connection
with the computer.
Use the F2 button and the F3 button to select (highlight)
the BUS POWER, then press F4 button to supply power from
the USB port and display the home screen.
NOTE
Power is supplied from the USB port when USB cable is
connected to the unit inserted with batteries (USB bus
power prioritized).
CAUTION
• Depending on the USB bus power specifications of the
computer, the DR-22WL may not operate with a USB
connection. If this occurs, please use the dedicated AC
adapter (TASCAM PS-P520E; sold separately) instead.
• This unit is not compatible with the computer’s power-save
mode or sleep-mode. Please turn off these modes when
operating the unit from the computer’s USB bus power.

TASCAM DR-22WL 11
3 – Preparation
Turning the power on and off (standby
mode)
CAUTION
• When you turn the power switch off while supplying power
from the dedicated AC adapter (TASCAM PS-P520E; sold
separately) or the USB bus power connected to a computer,
the unit will go to a standby mode.
• Before turning the power switch on and off, turn the volume
down for the sound system connected to the unit.
• Do not wear headphones when turning the power switch
on and off (standby mode); the noise may cause damage to
your ears and/or headphones.
Starting up the unit
In power off mode, slide and hold the HOLD/ switch
(located at left-side of the panel) toward the direction, and
release the switch when the TASCAM DR-22WL (start-up screen)
appears.
The DR-22WL starts up and the home screen is displayed.
Start-up screen Home screen
CAUTION
When turn the power on for the first time (or when the
built-in clock is reset due to no battery power), the DATE/
TIME screen will appear before the home screen to set date/
time. (See “Setting the date/time” on page 11.)
Shutting down (standby mode)
In power on mode, slide and hold the HOLD/ switch
(located at left-side of the panel) toward the direction, and
release the switch when the TASCAM DR-22WL shutting down…
appears.
The power turns off when the shut-down process is completed.
CAUTION
Always use the HOLD/ switch to turn the power off.
In power on mode, all recorded data and settings will be
lost if you remove the batteries, disconnect the power
cable of the dedicated AC adapter (TASCAM PS-P520E; sold
separately), or plug-off the USB cable for USB bus power.
Any lost data and/or settings cannot be restored.
Resume function
The DR-22WL is equipped with a resume function to locate the
previous position (or time) when the power was turned off.
Turn the power on and press the PL AY button to playback from
the previous file position (time) when the power was turned off.
NOTE
The position is recorded in the microSD card. The resume
function does not work if the microSD card is replaced or
formatted.
Selecting the language
You can change the language shown on the display. The first
time you turn the unit on after purchasing it, the LANGUAGE
screen will open. You can set the language used on this screen.
You can also change this setting with the SYSTEM screen
LANGUAGE item.
1. Use both the F2 and F3 buttons to move the cursor
and select the language.
Options
English:use English
日本語: use Japanese
Français:use French
Español: use Spanish
Deutsch:use German
Italiano:use Italian
Русский : use Russian
2. After making the selection, press the F4 button to
confirm it.
If you accidentally select the wrong
language
Slide the HOLD/ switch to turn the power off. Then, slide
the HOLD/ switch while pressing and holding the MENU
button to turn the unit on again.
The language selection menu where you can set the language
appears.
Setting the date/time
The DR-22WL uses its internal clock to record the date and time
to the recorded files.
1. Press the /MENU/8button to display the menu screen.
2. Press the F1 button to display the SETUP page.
3. Use both the F2 and F3 buttons to select (highlight)
the DATE/TIME item parameters.

12 TASCAM DR-22WL
3 – Preparation
4. Press the F4 button to display the DATE/TIME screen.
5. Press the F4 button to move the cursor (highlighted
area), and use the F2 and F3 buttons to change
settings.
6. Press the F1 button to finalize the settings. The screen
will return to the SETUP page.
NOTE
The file name will include the set date/time. (See “Setting
the file name type” on page 43.)
CAUTION
Without the use of the batteries, the dedicated AC adapter
(TASCAM PS-P520E; sold separately) or USB bus power, the
date and time setting can be made only for a few minutes.
When using batteries, we recommend to replace them
before they are completely drained.
Inserting and removing microSD cards
Inserting the SD card
NOTE
A microSD card is already installed at the time of purchase.
You can immediately start recording and playing tracks
without the need to remove and insert the microSD card.
1. Open the microSD card slot cover on the right side panel.
2. Insert the microSD Card into the slot (as illustrated below)
until it clicks into place.

Removing the card
1. Open the microSD card slot cover.
2. Gently press and release the microSD card; the card should
pop out.

CAUTION
• Do not remove the microSD card while the unit is accessing
data for recording, playback, etc.
• Do not remove the microSD card from the unit when
connected via USB cable to a computer.
• The DR-22WL is compatible with microSD/microSDHC/
microSDXC standards.
• A list of SD cards that have been confirmed for use with this
unit can be found on our web site. Please access to a product
page of this product from the TEAC Global Site (http://
teac-global.com) to find the list or contact the TASCAM
customer support service.
Setup the microSD card for use
To use a microSD card, it must be formatted first by the
DR-22WL.
1. Confirm that a microSD card is inserted and turn the power
on.
2. The following message appears when a new card or a card
formatted by another device is inserted into the unit.
micro SD/SDHC card
micro SDXC card
3. Press the F4 button to start formatting.
CAUTION
Formatting will delete all data from the card.
4. When formatting is complete, it will return to the home
screen. You may format the card whenever required.

TASCAM DR-22WL 13
3 – Preparation
CAUTION
Before formatting, make sure the unit is connected to
either a dedicated AC adapter (TASCAM PS-P520E; sold
separately), a computer via USB bus power, or fully-charged
batteries.
Turning the built-in speaker on/off
The factory setting for the built-in speaker output is selected as
ON. To turn the built-in speaker output off, set the SPEAKER item
to OFF on the TOOL menu page.
1. Press the /MENU/8button to display the menu screen.
2. Use the F1 button to display the TOOL page.
3. Use the F2 and F3 buttons to select (highlight) the
SPEAKER item and press the F4 button.
This shows the SPEAKER item parameters.
4. Use the F2 and F3 buttons to change settings, and
press the F4 button to finalize the setting.
Options: OFF, ON (default setting)
5. When setting is completed, press the /MENU/8button to
return to the home screen.
NOTE
In a recording standby or recording mode, or when a
headphone or a speaker system is connected to the
DR-22WL, the built-in speaker will not emit sound even
when the SPEAKER setting is ON.
Connecting a monitor device
To listen with headphones, connect them to the /LINE OUT
jack on the left side of the unit.
To listen with an external monitoring system (powered monitor
speakers or an amplifier and speakers), connect it to the /LINE
OUT jack.
Headphone
Powered monitor speaker or
an amplifier and speaker
Adjusting the playback volume
Use the OUTPUT LEVEL (+/−) buttons on the left side of the
unit to adjust the volume of output through the built-in speaker
and /LINE OUT connector.
When doing this, a volume position pop-up appears at the
bottom of the display.
When increasing the volume, this pop-up message might
appear: INCREASE YOUR RISK OF HEARING DAMAGE.
This warning appears when the volume is set above a level
recommended by the European Union (EU) to avoid hearing
damage (EU volume limit regulation).
Reconnecting headphones will reset the volume to its default
value.
NOTE
You can continue to adjust the volume even after the
pop-up message appears.
When you raise or lower the volume again, the pop-up
message will disappear.
CAUTION
Listening at high volumes could cause hearing damage. If
the surroundings are noisy, the sound of playback might
seem quieter than it actually is.
Start playback of the audio and check the volume before
putting on headphones, for example.

14 TASCAM DR-22WL
3 – Preparation
Input settings
Recording with the built-in microphone
Point the built-in microphone toward the sound source and
place the unit on a stable surface with minimum vibration.
Recording with an external microphone (MIC
IN)
Connect the external microphone to the MIC/EXT IN jack at
right side panel.
The following pop-up message will appear when connected to
the MIC/EXT IN jack.
Select the F3 button for plug-in-power microphones, or F2
button for other microphone types.
* Plug-in-power means that a power is delivered from the
recorder to the microphone
NOTE
Point the external microphone toward the sound source and
place the unit on a stable surface with minimum vibration.
CAUTION
• When not using a mic that requires plug-in power, do not
enable it by selecting the F3 button. Doing so could
damage connected equipment. See the mic operation
manual for details.
• When connecting a dynamic mic or external mic that has
its own battery, do not enable plug-in power by selecting
the F3 button. If plug-in power is turned ON, it could
damage such microphones.
Recording from an external device (LINE IN)
Connect a stereo mini-plug cable to the output of an external
audio device (i.e. headphone jack of a portable CD player).
Audio device or
external device
The following pop-up message will appear when connected to
the MIC/EXT IN jack.
When an external device is connected, select F2 button
(disable plug-in power).
CAUTION
If the input sound is still distorted after adjusting the input
level of the unit, reduce the playback sound of the external
device.

TASCAM DR-22WL 15
4 – Recording
In addition to the built-in microphone, an external microphone
or external audio devices (i.e. CD player) can also be used for
recordings.
Recordings can be made in MP3 (32k -320kbps, 44.1k/48kHz)
and WAV/BWF (44.1k/48k/96kHz, 16/24-bit) audio formats.
Cue marks in WAV file that supports BWF (Broadcast Wave
Format) can be used in BWF compatible softwares.
In addition, the DR-22WL can mix input signals while playing an
audio file and record a new file (overdubbing function).
Selecting the recording mode
8(SCENE:EASY)
Select the scene dial to .
The simple recording mode allows users to quickly start
recording by pressing the RECORD button just once; it
automatically adjusts the recording level. This feature is useful
for beginners and others wanting to make a quick-recording.
8(SCENE:MANUAL)
Select the scene dial to .
The manual mode allows to adjust the recording level manually,
suited for a higher-quality recording. This feature is especially
useful for those who wants to make fine-tuned recording.
Recording
1. Press the RECORD button to set the recording standby
mode.
The indicator around the RECORD button flashes and the
recording screen opens.
The bottom of the recording screen displays the recording
file name, the recording audio file type, and the sampling
rate. Users can confirm these information before starting
recording.
NOTE
When the scene dial is set at “ ", recording begins when
you press the RECORD button once.
2. Press the RECORD button again to start recording.
When recording starts, the RECORD indicator lights, and
displays the elapsed recording time and the remaining
recording time.
To pause, press the RECORD button while recording.
Press the RECORD button again to resume recording.
If you press the /MENU/8button while in pause mode,
the recorded audio file up to the pause point will be created.
3. Press the /MENU/8button to stop recording.
The recording stops and returns to the beginning of the file.
NOTE
• In recording standby mode, the speaker will not emit sound.
Use a headphone to listen to the input sound and make level
adjustments. In recording mode, operating the OUTPUT
LEVEL (+/−) button to adjust sound will not affect the
recording level.
• To avoid recording the RECORD button operation sound,
the DR-22WL begins recording about 0.3 seconds (fixed
time) after pressing the RECORD button.
CAUTION
Noise may occur during microphone recording when the
unit and AC adapter are in close proximity. If noise occurs,
move the AC adapter away from the unit.
Scene recording mode
The DR-22WL offers pre-set scenes that adjusts recording to the
most-suited level. Turn the scene dial and to set the following
scene:
8(SCENE:LOUD)
Suited for recording band performance and other scenes with
large sound volume.
8(SCENE:MUSIC)
Suited for recording voices, such as concert or group sining.
8(SCENE:INSTRUMENT)
Suited for recording near musical instruments, such as an
acoustic guitar and wind instruments.
8(SCENE:INTERVIEW)
Suited for recording an interview or take voice memos during
meetings.
NOTE
Recording level, low-cut filter, or level control are still
adjustable in scene recording mode.
However, level control cannot be adjusted in scene mode.
Settings are not stored and will be removed when scene
mode is changed.
Selecting a folder to store files
Recorded files will be saved in the current folder. If no setting is
made, they will be saved in the MUSIC folder. To change to the
folder that you want, follow the instructions in “5 – Using files
and folders (browse screen)”on page 25 to designate it.
When an SD card is initialized, the MUSIC folder will be set as the
current folder.

16 TASCAM DR-22WL
4 – Recording
Recording format settings
(FORMAT/SAMPLE/TYPE)
Select the desired audio file type before you start recording.
1. Press the /MENU/8button to display the menu screen.
2. Press the F1 button to open the REC SETTING menu
page.
FORMAT setting
3. Use the F2 and F3 buttons to select (highlight) the
FORMAT item and press the F4 button.
Open the parameter list for the FORMAT item.
4. Use the F2 and F3 buttons to select (highlight) the
file type.
Options: BWF 16bit, BWF 24bit, WAV 16bit (default value),
WAV 24bit, MP3 32k, MP3 64k, MP3 96k, MP3 128k, MP3
192k, MP3 256k, MP3 320k
NOTE
• BWF is a format for broadcasting that has the same sound
quality as the standard WAV format. It also uses the same
“.wav” file extension as WAV files. In this manual, we
distinguish these file types by using the terms BWF and WAV.
• The WAV format offers higher quality recording than MP3
files;
• On the other hand, the MP3 format can record for longer
hours.
• With MP3 format, recording with higher values offers better
quality.
• Cue marks in WAV file that supports BWF (Broadcast
Wave Format) can be used in BWF compatible devices and
computer softwares.
5. Press the F4 button to finalize the setting and return to
the item selection mode.
SAMPLE setting
6. Use the F2 and F3 buttons to select (highlight) the
SAMPLE item and press the F4 button.
Open the parameter list for the SAMPLE item.
7. Use the F2 and F3 buttons to select (highlight) the
sampling rate.
Options: 44.1k (default value), 48k, 96k
NOTE
96k cannot be selected for a MP3 format file.
TIPS
Selecting the WAV 16bit and 44.1kHz will allow you to
record in CD-quality.
8. Press the F4 button to finalize the setting and return to
the item selection mode.
TYPE setting
9. Use the F2 and F3 buttons to select (highlight) the
TYPE item and press the F4 button.
Open the parameter list for the TYPE item.
10. Use the F2 and F3 buttons to select (highlight) either
the stereo file or mono file.
Options: STEREO (default value), MONO
NOTE
• When MONO is selected, left and right channel signals will be
recorded separately .
• Selecting the WAV format MONO will extend the recording
hours by two times than the STEREO type, allowing for
longer recording hours.
11. Press the F4 button to finalize the setting and return to
the item selection mode.
12. Press the /MENU/8button to return to the home screen.

TASCAM DR-22WL 17
4 – Recording
Adjusting the input level
Before you start recording, ensure to adjust the input level to
prevent the recorded file from distortion or canceled by noise,
which can occur from excessively large or quiet input volume.
Use the limiter/peak reduction functions as necessary, in
addition to making manual adjustments.
TIPS
In addition to adjusting the input level, try changing the
distance and angle between the microphone and the sound
source. The angle and distance of the microphone can also
change the sound quality.
1. Press the RECORD button to set the recording standby
mode.
The RECORD indicator (around RECORD button) will flash
and displays the recording screen.
2. Use the INPUT LEVEL volume to adjust the input level. The
input level setting meter will pop-up at the bottom of the
display.
To obtain higher quality, it is recommended to set at the
maximum recording level. As a guideline, adjust the input
level until the −12dB indicator lights in green to obtain
the optimum level. To prevent possible distortion from
excessively large input volume, reduce the input level when
the PEAK indicator lights in red.
NOTE
• Press the /MENU/8button to cancel the recording
standby mode.
• In a recording standby or recording mode, the speaker will
not emit sound even when the SPEAKER setting is ON.
If you need to monitor sound to adjust the input level and
make recordings, connect the headphone to the /LINE
OUT jack.
To adjust monitor sound, go to home screen and use the
OUTPUT LEVEL (+/−) button. Adjusting the monitor sound
will not affect the recording quality.
Setting the peak hold function
Using the peak hold function makes monitoring the levels
easier.
1. Press the /MENU/8button to display the menu screen.
2. Press the F1 button to open the REC SETTING menu
page.
3. Use the F2 and F3 buttons to select (highlight)
the parameter of the PEAK HOLD item and press the F4
button.
Open the parameter list for the PEAK HOLD item.
4. Use the F2 and F3 buttons to select (highlight) the
peak hold mode.
Options:
OFF: Peak levels are not held.
1sec (default): Peak levels are held for one second.
HOLD: Peak levels are held until the peak clear ( )
button is pressed.
5. Press the F4 button to finalize the setting and return to
the item selection mode.
6. Press the /MENU/8button to return to the home screen.

18 TASCAM DR-22WL
4 – Recording
Setting the Low Cut Filter
The Low Cut Filter function can reduce noise from
air-conditioners, projector fans and unwanted wind noise.
1. Press the RECORD button to set the recording standby
mode.
The RECORD indicator will flash and displays the recording
screen.
2. Press the F4 button to display the input setting screen.
3. Press the F1 button to display the INPUT page of the
input setting screen.
4. Use the F2 and F3 buttons to select (highlight) the
parameter of the LOW CUT item and press the F4 button.
Open the parameter list for the LOW CUT item.
5. Use the F2 and F3 buttons to select (highlight) the
cut-off frequency.
Options: OFF (default value), 40Hz, 80Hz, 120Hz, 220Hz
6. Press the F4 button to finalize the selected cut-off
frequency for the Low Cut Filter.
7. Press the /MENU/8button to return to the recording
screen.
NOTE
• When the low-cut filter is on, the icon appears on the
recording screen.
• The low-cut filter can be set and changed when in recording
standby.
TIPS
• Setting it to larger value can reduce more noise in the
low-frequency range, but this is not recommended when
recording music.
• The DR-22WL has a built-in reverb, which can be added to
the input source as desired. (See “Reverb function” on page
32.)
Using the level control function
You can set the recording level for microphone input.
1. Press the RECORD button to set the recording standby
mode.
The RECORD indicator will flash and displays the recording
screen.
2. Press the F4 button to display the input setting screen.
3. Press the F1 button to display the INPUT page of the
input setting screen.
4. Use the F2 and F3 buttons to select (highlight) the
parameter of the LEVEL CONTROL item and press the F4
button.
Open the parameter list for the LEVEL CONTROL item.
5. Use the F2 and F3 buttons to select (highlight) the
function.
Options: OFF (default value), LIMITER, PEAK
6. Press the F4 button to finalize the selected function.
7. Press the /MENU/8button to return to the recording
screen.
The selected function is shown with an icon in the recording
screen.
NOTE
The selected mode is shown with an icon in the recording
screen.
• When the limiter function is ON, the icon will appear
on the recording screen.
• When the peak reduction function is ON, the icon
will appear on the recording screen.
8LIMITER
The limiter functions only at excessive input level.
This function is useful for musical instrument performance and
musical recordings.
8PEAK
This function automatically reduce the recording level to an
appropriate value when input signal is too high. It is useful
when you cannot preset the recording level or unable to make
adjustments during recordings.
CAUTION
Distortion might occur if the input sound is too loud even
when the limiter is on. In such a case, lower the input level
or increase the distance between the mic and the sound
source.
NOTE
When level control function is ON, you can still adjust the
recording level by using the INPUT LEVEL volume. This
function cannot be used, however, when the scene dial is set
to or .

TASCAM DR-22WL 19
4 – Recording
Switching files during recording
(track increment)
During recording, you can switch to a new recording file either
manually or at a set time, and continue to make recording in the
new file. (Track increment function)
Manual track increment during recording
During recording, you can easily update a file manually and
continue to make recording.
1. During recording, press the F1 button.
NOTE
Numbers at the end of file name will increment each time
when a new file is created.
CAUTION
• The maximum total number of folders and files you can
create is 5,000.
• Files with a recording time of less than two seconds cannot
be created.
• The number of the new file will increment if its name is the
same as the existing file.
• Track increment function is not available during
overdubbing.
Automatic track increment at specified time
Without pausing recording, a new file can be created
automatically during recording when the time set using the
TRACK INC item on the AUTO FUNCTION screen is reached (track
increment function).
Follow the below steps to set the maximum time for automatic
increment:
1. Press the /MENU/8button to display the menu screen.
2. Press the F1 button to open the REC SETTING menu
page.
3. Use the F2 and the F3 buttons to select (highlight)
the parameter of the AUTO FUNC item and press the F4
button.
AUTO FUNCTION screen is displayed.
4. Use the F2 and the F3 buttons to select (highlight)
the parameter of the TRACK INC item and press the F4
button.
This shows the TRACK INC item parameters.
5. Use the F2 and the F3 buttons to select the
automatic track increment time.
Options: OFF (default value), 5min, 10min, 15min, 30min,
60min
6. Press the F4 button to finalize the selected time.
CAUTION
The maximum total number of folders and files you can
create is 5,000.
Automatic recording (AUTO REC)
When the auto record function is on, the unit can respond to
input sound levels and start and pause recording and create
new files automatically.
1. Press the /MENU/8button to display the menu screen.
2. Press the F1 button to open the REC SETTING menu
page.
3. Use the F2 and the F3 buttons to select (highlight)
the parameter of the AUTO FUNC item and press the F4
button.
AUTO FUNCTION screen is displayed.
4. Use the F2 and the F3 buttons to select (highlight)
the parameter of the AUTO REC item and press the F4
button.
This shows the AUTO REC item parameters.
5. Use the F2 and F3 buttons to select a level that
activates the AUTO REC function (a level that recognize
incoming signal).
Options: OFF (default value), -6dB, -12dB, -24dB, -48dB
6. Press the F4 button to finalize the selected level that
activates the AUTO REC function.
7. Press the /MENU/8button to return to the home screen.
8. Press the RECORD button to set the recording standby
mode.
The level meter will display sounds within the level that
activates the AUTO REC function and the icon will
appear on the right side of the recorder status display.
Recording starts automatically when the input signal
exceeds the threshold set in the LEVEL item.
NOTE
• When in recording standby, the RECORD indicator flashes
faster than when recording.
• When recording, if the input signal level falls below the level
set with the LEVEL item for more than 5 seconds, the unit
pauses recording and creates a new file. When the input
signal level becomes higher than the set level again, it starts
recording to a new file.

20 TASCAM DR-22WL
4 – Recording
• When new files are created, incremental numbers are added
to the end of each file name.
9. When you need to stop recording, press the /MENU/8
button.
CAUTION
• A new file cannot be created if the total number of folders
and files would exceed 5000.
• Files shorter than 2 seconds cannot be created. If the
sampling frequency is 96 kHz, files shorter than 4 seconds
cannot be created.
• If the name of a newly created file would be the same as
that of an existing file, the number will be incremented until
the new file has a unique name.
TIP
By using this in combination with the PRE REC function, you
can record events without losing the beginnings of sounds.
Start recording from slightly before
pressing record (PRE REC)
PRE REC function will allow you to start recording up to two
seconds before the desired timing, by recording an input signal
(up to two seconds) during the recording standby mode.
1. Press the /MENU/8button to display the menu screen.
2. Press the F1 button to open the REC SETTING menu
page.
3. Use the F2 and the F3 buttons to select (highlight)
the parameter of the PRE REC item and press the F4
button.
Open the parameter list for the PRE REC item.
4. Use the F2 and F3 buttons to turn on the PRE REC
function.
Options: OFF (default value), ON
5. Press the F4 button to finalize the setting and return to
the item selection mode.
6. Press the /MENU/8button to return to the home screen.
TIPS
By combining PRE REC with the AUTO REC function, you will
not miss an opportunity to start recording.
NOTE
• When the pre-recording function is on, the icon
appears on the right of the recorder operation status area
on the recording screen.
• If you start recording within two seconds from when the
record standby mode is turned ON, recording will begin
from the record standby mode.
• PRE REC function will not work during overdubbing.
Using the SELF TIMER for recording
Similar to a camera, the DR-22WL has a SELF TIMER function to
begin recording after a set period of time.
1. Press the RECORD button to enter recording standby.
The indicator around the RECORD button flashes and the
recording screen opens.
2. Press the F1 button to turn the self-timer on, making its
icon appear in the recorder operation status area.
The time is shown below the self-timer icon. Each time
you press the F1 button, the setting changes as follows.
Time display below the icon
No display (OFF) w5S (5 sec.) w10S (10 sec.) wno
display (OFF)
3. After setting the time, press the RECORD button. The
RECORD indicator will flash more quickly until recording
starts after the set amount of time passes.
NOTE
• SELF TIMER function will not work when recording is on
pause.
• SELF TIMER function can be used in the Automatic recording
function. When recording begins, the Automatic recording
function is prioritized.