Tascam 24 User manual

TASCAM Model 24 1
Model 24
Checking the firmware version
Confirm the firmware version of your Model 24 before conducting a firmware update.
1. Turn the main unit on.
2. Press the MENU button to open the MENU Screen.
3. On the SYSTEM Screen, select INFORMATION to open the
Information Screen.
4. Turn the MULTI JOG dial to open the FIRMWARE screen.
5. Check the VERSION (system firmware version) on this screen.
Updating is not necessary if the VERSION shown here is the
same or newer than the firmware version you intend to use
for the update.
NOTE
i The screen shown above is an example. The actual appear-
ance will differ.
i For details, see the“FIRMWARE screen”section of Chapter “8 –
Settings and Information” in the Model 24 Owners Manual.
Firmware update procedures
1. Download the latest firmware from the TEAC Global Site
(http://teac-global.com/).
Decompress the downloaded file if it is in ZIP format or
another compressed file type.
2. Confirm that an SD card is loaded in the unit, turn the unit
on and connect it to the computer using a commercial-
ly-available USB cable (Type-A - Type-B).
ATTENTION
The unit should be connected directly to the computer, not
through a USB hub. Moreover, noise could be picked up if the
cable is too long.
3. On theMENU Screen, select STORAGE to open the STORAGE
Screen.
4. To connect with the computer, press the F4 button.
The unit enters USB storage mode and connects with the
computer.
5. This unit appears on the computer as an external drive
named “TASCAM_M” (if the card was formatted by this unit).
Copy the downloaded firmware to the “UTILITY” folder on
“TASCAM_M”.
NOTE
The Model 24 firmware update file will have a name like
“Model24_XXXX.XXX”.
6. After copying, use the proper procedures for the computer
to unmount the unit.
See the computer’s operation manual for instructions about
how to unmount an external volume.
Press the F1 button to return to the Meter Screen.
Then, turn the unit off.
7. Turn the unit on while pressing the 8and mbuttons.
This will start the unit in update mode, and the update file
will appear on the display.
ATTENTION
i If this screen does not appear, turn the power off once, and
turn the unit on again while pressing the 8and mbut-
tons. Keep pressing the 8and mbuttons until this screen
appears.
i If the firmware was copied to the “UTILITY” folder from a Mac,
in addition to the firmware itself, another file with “._” before
the firmware name will also appear. Select the file without “._”
at the beginning.
NOTE
i This screen shows a list of firmware update files in the “UTIL-
ITY” folder in the unit. The firmware copied in step 5above
should also be shown. “No Update File” is shown if the
folder does not contain an update file.
i The screen shown above is an example. The actual appear-
ance will differ.
8. Turn the MULTI JOG dial to select the firmware, and press
the MULTI JOG dial. The screen shown below will appear.
The number of the current version is shown on the left and
the update version is shown on the right.
NOTE
The screen shown above is an example. The actual appear-
ance will differ.
1218.MA-2830A

2 TASCAM Model 24
Model 24
9. Press the F4 button to start updating. (To cancel
updating, press the F1 button instead.)
CAUTION
i Be careful not to let the power be interrupted during the
update.
i Do not load or remove SD cards during the update.
i If the power is interrupted or an SD card is loaded or re-
moved during the update, the unit might become unstart-
able.
10. When the update completes, the following message will
appear.
11. Press the POWER switch to turn the unit off. Then, turn it on
again.
12. Refer to“Checking the firmware version”and confirm that
the firmware has been updated to the latest version.
13. Connect the unit with a computer using USB, and delete
the firmware update file in the “UTILITY” folder.
This completes updating the unit.