TCS FBI6100-0400 User manual

TCS TürControlSysteme AG, TCS Hotline Germany: [email protected]e Subject to technical changes.
www.tcsag.de PI_FBI610x_uk 3 A
Product information
SIP-Gateway
for 115 call destinations FBI6100-0400
for 10 call destinations FBI6101-0400

2 02/2014
TCS TürControlSysteme AG, TCS Hotline Germany: [email protected] Subject to technical changes.
www.tcsag.de PI_FBI610x_uk 3 A
Table of contents
Scope of delivery .................................................................................................................2
Please note!..................................................................................................................2
Safety instructions................................................................................................................3
Connections, indication and operating elements .................................................................3
Device overview...................................................................................................................5
Technical data .....................................................................................................................5
Intended use........................................................................................................................6
Short description..................................................................................................................6
Connect the lines.................................................................................................................6
Notes................................................................................................................................6
Connect the TCS system .................................................................................................6
Connect the network ........................................................................................................6
Wiring example operation mode ACTIVE.........................................................................7
Wiring example: operation mode PASSIVE .....................................................................7
Commissioning ....................................................................................................................8
Note..................................................................................................................................8
Error detection and indication...........................................................................................8
Start browser: connection establishment PC –SIP Gateway ..............................................8
Prepare the intranet connection .......................................................................................8
Example: network setup under Windows XP....................................................................9
Establish a network connection for configuration ...........................................................10
Enter / change IP address..............................................................................................11
Change the password ....................................................................................................11
Enter / change SIP settings............................................................................................12
Configure the phonebook...............................................................................................13
Adjust the switch time for door opener and light relay....................................................14
Programming the TCS front-door station........................................................................14
Operation...........................................................................................................................15
Door call from front-door station.....................................................................................15
Call from a telephone to a front-door station..................................................................15
Reload to factory settings...............................................................................................16
Service...............................................................................................................................16
Scope of delivery
1 x FBI610x-0400
1 x product information
Please note!
This product information describes the necessary steps to connect the FBI610x with a
TCS front-door station and with a SIP server.
For detailed information refer to the FBI610x user manual. You’ll find the manual for free
download under www.tcsag.de.

02/2014 3
TCS TürControlSysteme AG, TCS Hotline Germany: [e-mail] Subject to technical changes.
www.tcsag.de PI_FBI610x_uk 3 A
Safety instructions
!
Attention! Mounting, installation, commissioning and repair of electronic devices have
to be carried out only by qualified electricians. Thus, the current standards for the in-
stallation of door communication systems must be observed!
For working with main connection of 230 V alternating voltage, the safety regulations ac-
cording to DIN VDE 0100 must be observed.
When installing TCS:BUS systems, the general safety regulations for telecommunication
systems according to VDE 0800 must be observed. Inter alia:
separated conduit of heavy and low current lines,
minimum distance of 10 cm in case of a common cable conduit,
use of separators between heavy and low current lines within shared cable ducts,
use of standard communication lines, e.g. J-Y (St) Y with 0.8 mm diameter,
existing lines (modernisation) with deviating cross-sections can be used in compliance
with the loop resistance.
!
With suitable measures to protect against lightning, it has to be ensured that a voltage
of each 32 V DC is not exceeded at the a- and b-wire.
Connections, indication and operating elements
Labelling
Function
19|20
connection for supply
voltage
Only operation mode ACTIVE! 8 - 12 V AC (from bell
transformer NWV1000-0400)
23|24|25
a*/b*/P*
connection TCS:BUS
ACTIVE
Only operation mode ACTIVE!
The SIP-Gateway realises the supply voltage for a
BUS strand.
In this operation mode, a front-door station can be
connected to the network at minimal effort.
One audio front-door station (incl. extensions) and 3
audio indoor stations can be operated in this mode.
The selection of connectable devices must be real-
ised in compliance with the max. quiescent current
output of the FBI610x.
Terminals are short-circuit protected.

4 02/2014
TCS TürControlSysteme AG, TCS Hotline Germany: [email protected] Subject to technical changes.
www.tcsag.de PI_FBI610x_uk 3 A
28|29|30
a/b/P
connection TCS:BUS
PASSIVE
Only operation mode PASSIVE!
The supply voltage for the TCS:BUS is provided by an
additional power supply and control unit.
This operation mode is selected if the SIP-Gateway
is integrated into e.g. a video system, a system with
several front-door stations, resp. if the system
which is to be supplied exceeds the power output of
the SIP-Gateways.
Terminals are short-circuit protected.
21|22
Door release relay
(potential-free relay
contact –closing con-
tact)
door release voltage via bridge terminal 20 to 21
12 V, 50/60 Hz / 2 A (for door opener not less than
6 Ohm)
door release time can be adjusted: 0 to 99 sec
function can be adjusted via web interface
26|27
Internal light switch
relay (potential-free
relay contact –closing
contact)
To control automatic light switching units,
the following extensions can be connected:
automatic light switch unit (max. permitted contact
load capacity of 24 V DC / 1 A)
staircase light control unit FNA1000 (or TZ1-SG)
(with 8 - 24 V AC)
relay
adjustable light switch time: 0 to 99 sec
adjustable function via web interface
RJ45 socket
connection for network (PC/Laptop) 10/100 Mbit
RUN/PROG push
button
Only operation mode ACTIVE!
Switching of the system mode:
operation mode –programming mode
RUN
PROG
RUN/PROG indication
(LED orange)
indication of the system mode:
is ON: operation mode
blinks: programming mode
ERR
error indication at
TCS:BUS (LED red)
flashes: error in the connection to the TCS:BUS
(see page 8)
flashes OFF: error in the network connection (see
page 8)
2
indication operation
voltage (LED green)
is ON: operation voltage is present
3
indication status voice
connection (LED or-
ange)
indication voice connection or connection estab-
lishment FBI610x to an external device
4
error indication SIP
(LED red)
is ON: start process (around 40 sec) or no connec-
tion to the SIP server (see page 8)
status indication (LED
green)
blinks: if data is sent or received via LAN
is ON: connection FBI610x to the network is estab-
lished
status indication (LED
orange)
is ON simultaneously green with status indication:
no connection to the network

02/2014 5
TCS TürControlSysteme AG, TCS Hotline Germany: [e-mail] Subject to technical changes.
www.tcsag.de PI_FBI610x_uk 3 A
Device overview
Technical data
housing: DIN-rail housing 6 SU for DIN-rail according to
DIN EN 60715 TH35
weight: 215 g
acceptable ambient temperature: 0 °C ... +40 °C
degree of protection: IP 20
operation mode ACTIVE
supply voltage: 8-12 V AC (from bell transformer NWV1000-0400)
output voltage idle state: U(a/b) = 24 V ± 1 V, U(b/P) = 26V ± 1V
output voltage speaking: U(a/b) = 22 V ± 1 V
output current: I(a) =40 mA,
max. output current: I(Pmax) = 180 mA
operation mode PASSIVE:
supply voltage: +26 V ±8 % (power supply and control unit)
input current: I(a) = 0.05 mA, I(P) = 27 mA
max. input current: I(Pmax) = 45 mA
connection RJ45
status indication
(LED orange)
status indication
(LED green)
error indication
at the TCS:BUS
(LED red)
RUN/PROG
indication
RUN/PROG-
push button
connection
supply voltage
indication for operation
voltage (LED green)
indication for status voice
connection (LED orange)
error indication
SIP (LED red)

6 02/2014
TCS TürControlSysteme AG, TCS Hotline Germany: [email protected] Subject to technical changes.
www.tcsag.de PI_FBI610x_uk 3 A
Intended use
The FBI610x is an interface for the connection of TCS front-door stations to a VoIP net-
work as end device (client) via Session Initiation Protocol (SIP).
The SIP-Gateway can be used generally in 2 operation modes at the TCS:BUS: opera-
tion mode ACTIVE or operation mode PASSIVE.
Short description
providing the voltage supply of 24 V DC (for TCS:BUS, only operation mode ACTIVE)
switching of the system mode between operation and programming mode,
LED indication (only in operation mode ACTIVE).
automatic detection of the operation mode PASSIVE or ACTIVE
potential-free relay contacts (closing contacts) to control automatic light switch units /
door opener
single speech channel:
Communication from front-door and indoor stations to more than one call destination is
not possible simultaneously.
optical indication for voice connection and operating voltage
error detection and indication for TCS:BUS and network errors
Connect the lines
Notes
Mounting, installation and commissioning must be carried out only by IT professionals!
!
Use a small screwdriver to connect the lines and to avoid damaging the device.
Connect the TCS system
Strip the ends of the lines.
Connect the TCS system to the FBI610x depending on the operation mode and the type
of system completely and according to the wiring example.
Connect the network
Establish a connection between the RJ45 interface at the FBI610x and your network by
using a patch cord.

02/2014 7
TCS TürControlSysteme AG, TCS Hotline Germany: [e-mail] Subject to technical changes.
www.tcsag.de PI_FBI610x_uk 3 A
Wiring example operation mode ACTIVE
Wiring example: operation mode PASSIVE

8 02/2014
TCS TürControlSysteme AG, TCS Hotline Germany: [email protected] Subject to technical changes.
www.tcsag.de PI_FBI610x_uk 3 A
Commissioning
Install the devices of the system completely.
Check the a-, b- and P-wire against each other for short-circuits.
Switch on the mains voltage.
After switching on the voltage supply, the FBI610x starts automatically.
Note
!
The SIP Gateway restarts automatically after a voltage interruption, even if the
device was switched off.
!
Switching off the power supply during a storage process or software update can cause
a loss of data or a malfunction of the device.
Error detection and indication
Error at the TCS:BUS
Only operation mode PASSIVE: a-wire is not
connected / not supplied, a-b short-circuit or a-
and P-wire are interchanged / short-circuited
Only operation mode ACTIVE: a-b or a-P
short-circuited
ERR
error indication flashes
(1:7, 1 Hz)
Connect a-wire / check power
supply,
interchange a- and P-wire or re-
move short-circuit,
device is in standby mode again
Network error
defective network connection or no connection
to the SIP server
ERR
error indication
flashes out
(7:1, 1 Hz)
Check the network, check data
transmission, check login data for
SIP server,
device is in standby mode again
Network error
defective network connection or no connection
to the SIP server
4
error indication SIP
lights up *
Check the network, check the
data transmission, check the
SIP server,
device is in standby mode again
*No error during the start process, indication, lights up and expires after around. 40 sec if no error was detected.
Start browser: connection establishment PC –SIP Gateway
Prepare the intranet connection
The PC/Laptop must be equipped with a network connection and the device must be lo-
cated in the same subnet as the SIP-Gateway. If your network and server are working in
the 192.168.1 address area (C net), you can directly access the SIP-Gateway (provided
that another device does not use the IP address of the SIP-Gateway).
Otherwise the used PC/Laptop must be set temporary to an IP address within the address
area of the FBI610x to establish a connection with the SIP-Gateway. To install / modify
your network connection, please use the network installation assistant or the help menu of
your operating system (catchword: Install the network). If several FBI610x, which are in
delivery state, are to be installed within one network, the devices must be commissioned
one by one and assigned to a free IP address.

02/2014 9
TCS TürControlSysteme AG, TCS Hotline Germany: [e-mail] Subject to technical changes.
www.tcsag.de PI_FBI610x_uk 3 A
To install the network connection, you eventually need administrator rights.
In delivery state, the following values are pre-set at the FBI610x:
IP address: 192.168.1.200, net mask: 255.255.255.0, password: 1234
To setup / adjust your network connection, please use the network installation assistant or
the help of your operation system (catchword: Network setup).
Example: network setup under Windows XP
Open the Network and data telecommunication connections in one of the following
methods:
1. Click with the right mouse button on the icon Network surrounding on the desktop and
select Settings.
or
2. Click the button Start (toolbar on your desktop) > Settings > System control > Network
connection.
Select LAN connection in the menu.
Select Settings.
Click Internet protocol (TCP/IP)
(see illustration).
Click Settings.
Activate Use the following IP-address.
Enter an IP-address, which differs from the one
of the TCS:Server only in its last digit, e.g.
192.168.1.5.
Enter the number of the subnet mask:
255.255.255.0.
Confirm with OK.

10 02/2014
TCS TürControlSysteme AG, TCS Hotline Germany: [email protected] Subject to technical changes.
www.tcsag.de PI_FBI610x_uk 3 A
Establish a network connection for configuration
Establish a connection from the PC/Laptop to the SIP-Gateway via switch or router.
Alternatively connect the SIP-Gateway directly to a PC/Laptop via a crossover cable
(twisted pair cable).
Open an internet browser.
Enter the IP address of the
SIP Gateway into the address line:
http://192.168.1.200
The start page is called.
Select Settings VoIP.
Enter the password (preset: 1234)
and select Register.