Team Losi EIGHT User manual

Before operating this vehicle, please read all printed materials thoroughly.
Horizon Hobby is not responsible for inadvertent errors in this manual.
INSTRUCTION MANUAL
BEDIENUNGSANLEITUNG
MANUEL D’UTILISATION
MANUALE DI ISTRUZIONI
1/8-SCALE HIGH-PERFORMANCE 4WD NITRO BUGGY
1/8-SCALE HIGH-PERFORMANCE 4WD NITRO TRUGGY

LOSI 8IGHT/8IGHT-T RTR • INSTRUCTION MANUAL
2
EN
Your new Horizon Hobby vehicle has been designed and built with a combination of
waterproof and water-resistant components to allow you to operate the product in
many “wet conditions,” including puddles, creeks, wet grass, snow and even rain.
While the entire vehicle is highly water-resistant, it is not completely waterproof and
your vehicle should NOT be treated like a submarine. While the various electronic
components used in the vehicle may be waterproof, most of the mechanical
components are water-resistant and should not be submerged.
Metal parts, including the bearings, hinge pins, screws and nuts, as well as the
contacts in the electrical cables, will be susceptible to corrosion if additional
maintenance is not performed after running in wet conditions. To maximize the long-
term performance of your vehicle and to keep the warranty intact, the procedures
described in the “Wet Conditions Maintenance” section below must be performed
regularly if you choose to run in wet conditions. If you are not willing to perform the
additional care and maintenance required, then you should not operate the vehicle in
those conditions.
CAUTION: Failure to exercise caution while using this product and
complying with the following precautions could result in product
malfunction and/or void the warranty.
General Precautions
• Read through the wet conditions maintenance procedures and make sure that
you have all the tools you will need to properly maintain your vehicle.
• Not all batteries can be used in wet conditions. Consult the battery manufacturer
before use. Caution should be taken when using Li-Po batteries in wet conditions.
• Most transmitters are not water-resistant. Consult your transmitter’s manual or
the manufacturer before operation.
• Never operate your transmitter or vehicle where lightning may be present.
• Do not operate your vehicle where it could come in contact with salt water (ocean
water or water on salt-covered roads), contaminated or polluted water. Salt water
is very conductive and highly corrosive, so use caution.
• While the air filter assembly can be designed to limit or restrict water ingestion
into the engine, no air filter is completely waterproof. If too much water is
ingested into the engine, severe damage to the engine may result.
• Do not expose your engine to rapid changes in temperature. These engines
tend to operate at temperatures between 200–265°F (93–129°C) in normal
operating conditions. If the engine is exposed to cold water while operating at this
temperature, there is a risk of “thermal shock,” which could cause undue stress
on the engine and a shortened engine lifespan.
• Driving in wet conditions can reduce the life of the engine. The additional
resistance of operating in water causes excess strain. Alter the gear ratio by
using a smaller pinion or larger spur gear. This will reduce the load on the engine
(and engine temperatures) when running in mud, deeper puddles, or any wet
conditions that will increase stress on the engine for an extended period of time.
As the user of this product, you are solely responsible for operating it in a manner that
does not endanger yourself and others or result in damage to the product or property
of others.
This model is controlled by a radio signal subject to interference from many sources
outside your control. This interference may cause momentary loss of control, so it is
advisable to always keep some distance in all directions around your model as this
margin will help you avoid collisions or injury.
• Always ensure all screws and nuts are tightened.
• Always carefully follow the directions and warnings for this and any optional
support equipment.
• Always keep all chemicals, small parts and anything electrical out of the reach
of children.
• Always ensure the failsafe is properly set during binding.
• Always operate your model in an open area away from cars, traffic and people.
• When operating this vehicle, always keep it at least 20 feet from spectators,
especially small children.
• Never run your vehicle through deep water that will submerge the vehicle.
• Never run your model in a public street where damage can occur.
• Never run your model with low transmitter batteries.
• When finished operating, always power off the engine first, then the receiver,
then the transmitter.
• Always perform maintenance on the vehicle after each and every use. Due to
engine vibration, all screws and nuts will need to be checked to ensure they
are tight.
WARNING: Read the ENTIRE instruction manual to become familiar with the features of the product before operating. Failure to operate the product correctly can
result in damage to the product, personal property and cause serious injury.
This is a sophisticated hobby product and NOT a toy. It must be operated with caution and common sense and requires some basic mechanical ability. Failure to operate this
Product in a safe and responsible manner could result in injury or damage to the product or other property. This product is not intended for use by children without direct
adult supervision. Do not use with incompatible components or alter this product in any way outside the instructions provided by Horizon Hobby, LLC. This manual contains
instructions for safety, operation and maintenance. It is essential to read and follow all the instructions and warnings in the manual, prior to assembly, setup or use, in order
to operate correctly and avoid damage or serious injury.
AGE RECOMMENDATION: NOT FOR CHILDREN UNDER 14 YEARS. THIS IS NOT A TOY.
The following terms are used throughout the product literature to indicate various levels of potential harm when operating this product:
NOTICE: Procedures, which if not properly followed, create a possibility of physical property damage AND a little or no possibility of injury.
CAUTION: Procedures, which if not properly followed, create the probability of physical property damage AND a possibility of serious injury.
WARNING: Procedures, which if not properly followed, create the probability of property damage, collateral damage, and serious injury OR create a high probability of
superficial injury.
NOTICE
All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby, LLC. For up-to-date product literature, visit
www.horizonhobby.com and click on the support tab for this product.
Meaning of Special Language
Water-Resistant Vehicle with Waterproof Electronics
Safety Precautions and Warnings

EN
3
LOSI 8IGHT/8IGHT-T RTR • INSTRUCTION MANUAL
1/8-SCALE HIGH-PERFORMANCE 4WD NITRO BUGGY
• Losi®8IGHT™ Nitro RTR: 1/8-Scale 4WD Buggy (LOS04010)
• Spektrum™ DX2E 2.4GHz Transmitter (SPM2330)
• SPMSR310 3-Channel DSMR®Surface Receiver (SPMSR310)
• Dynamite®.21 Nitro Pull-Start Engine (DYNE0570)
• Dynamite®6V 1600mAh Ni-MH Receiver Pack, 3+2 Hump (DYN1453)
• (2) 9KG Servos, Waterproof, 23T (SPMS605)
Tools Included
• 4-Way Cross Wrench
• Bind Plug
Needed to Complete
• 20–30% Nitromethane fuel
• Nitromethane-Approved Dispenser
• NiMH Charger
• Glow Igniter
Use only Dynamite tools or other high-quality tools. Use of inexpensive tools
can cause damage to the small screws and parts used on this type of model.
Components
Wet Conditions Maintenance
• Remove the battery pack(s) and dry the contacts. If you have an air compressor
or a can of compressed air, blow out any water that may be inside the recessed
connector housing.
• Remove the tires/wheels from the vehicle and gently rinse the mud and dirt off
with a garden hose. Avoid rinsing the bearings and transmission.
NOTICE: Never use a pressure washer to clean your vehicle.
• Use an air compressor or a can of compressed air to dry the vehicle and help
remove any water that may have gotten into small crevices or corners.
• Spray the bearings, drive train, fasteners and other metal parts with a water-
displacing light oil or lubricant.
• Let the vehicle air dry before you store it. Water (and oil) may continue to drip
for a few hours.
• Increase the frequency of disassembly, inspection and lubrication of the
following:
•Frontandrearaxlehubassemblybearings.
•Alltransmissioncases,gearsanddifferentials.
•Engineairlterelement.
•Engineclutchassembly,includingshoesandbearings.
1/8-SCALE HIGH-PERFORMANCE 4WD NITRO TRUGGY
• Losi®8IGHT-T™ Nitro RTR: 1/8-Scale 4WD Truggy (LOS04011)
• Spektrum™ DX2E 2.4GHz Transmitter (SPM2330)
• SPMSR310 3-Channel DSMR®Surface Receiver (SPMSR310)
• Dynamite®.28 Nitro Pull-Start Engine (DYNE0571)
• Dynamite®6V 1600mAh Ni-MH Receiver Pack, 3+2 Hump (DYN1453)
• 9KG Throttle Servo, Waterproof, 23T (SPMS605)
• Steering Servo (SPMSS6100)
Tools Included
• 4-Way Cross Wrench
• Bind Plug
Needed to Complete
• 20–30% Nitromethane fuel
• Nitromethane-Approved Dispenser
• NiMH Charger
• Glow Igniter
Use only Dynamite tools or other high-quality tools. Use of inexpensive tools
can cause damage to the small screws and parts used on this type of model.

LOSI 8IGHT/8IGHT-T RTR • INSTRUCTION MANUAL
4
EN
Dynamite 6V 1600mAh NiMH Receiver Pack
1. Remove the NiMH receiver battery pack from the battery box and disconnect
the universal connector.
2. Connect the NiMH battery charger to an AC power outlet.
3. Refer to manufacturers battery charging directions.
Installing the Receiver Battery in the Battery Box
1. Connect the fully charged NiMH battery pack to the connector
in the battery box.
2. Place the battery box cover on the battery box.
Charging the Receiver Battery Pack
Installing the Transmitter Batteries
This transmitter requires 4 AA batteries.
1. Remove the battery cover from the transmitter.
2. Install the batteries as shown.
3. Install the battery cover.
CAUTION: If using rechargeable batteries, charge only rechargeable batteries.
Charging non-rechargeable batteries may cause the batteries to burst, resulting
in injury to persons and/or damage to property.
CAUTION: Risk of explosion if battery is replaced by an incorrect type. Dispose
of used batteries according to national regulations.
Spektrum DX2E Radio System
For more information on the transmitter, go to www.horizonhobby.com and click on
the support tab for the Spektrum DX2E to download the instruction manual.
1. Steering Wheel Controls direction (left/right) of the model
2. Throttle Trigger Controls speed (forward/brake) of the model
3. BIND Button Puts the transmitter into Bind Mode
4. ON/OFF Switch Turns the power ON/OFF for the transmitter
5. ST REV Reverses the function of the steering when the wheel is turned left
or right
6. Indicator Lights
-Solid green light—indicates adequate battery power
-Flashing green light—indicates the battery voltage is critically low.
Replace batteries
7. TH REV Reverses the function of the speed control when pulled back or pushed
forward
8. ST Trim Adjusts the steering center point
9. TH Trim Adjusts the throttle neutral point
10. ST Rate Adjusts the steering limits
11. Antenna Transmits the signal to the model
1
2
11
4
10
7
8
56
3
9
WARNING: Read all instructions before use. Improper use of batteries
can result in fire causing serious injury and damage to property.
• NEVER LEAVE THE CHARGING BATTERIES UNATTENDED DURING USE.
• NEVER CHARGE BATTERIES OVERNIGHT.
• Never leave batteries near fire or in extreme temperatures.
• Never short-circuit or modify batteries as this may cause fire.
• Always use a compatible charger and discontinue use if batteries become hot
during charging.
• Dispose of batteries properly.
NiMH Battery Warnings

EN
5
LOSI 8IGHT/8IGHT-T RTR • INSTRUCTION MANUAL
Driving Precautions
• Always observe all warnings, precautionary statements and instructions
supplied by the fuel manufacturer/provider.
• Fuel is a fire accelerant. Never operate your vehicle near open flames. Never
smoke while operating your vehicle or while handling fuel.
• Always use caution when handling fuel.
• Always run your model engine in a well-ventilated area. Model engines produce
harmful carbon monoxide fumes.
• Always drain your engine after you have finished running your vehicle. Do not
store the vehicle with fuel in the fuel tank.
• Never handle model engines and mufflers until they have had time to cool.
They become extremely hot when in use.
• Always store your fuel in a safe place well away from sparks, heat or anything
that can ignite.
• Always ensure that fuel is stored in a clearly marked container well away from
the reach of children.
• Never allow fuel to come into contact with eyes or mouth. Fuels used in model
engines are poisonous.
• Never return unused fuel from the fuel tank back into the fuel container.
• Contact your local waste disposal authorities for more information about
discarding fuel waste responsibly.
Appropriate carburetor adjustment is critical when running a nitro-powered RC
vehicle. The fuel mixture is “rich” when there is too much fuel and “lean” when
there is not enough fuel for the amount of air entering the engine. Using a flat-head
screwdriver, adjust the high- and low-speed needles to control the amount of fuel
entering the engine. The low-speed needle is located in the front of the moving slide.
The high-speed needle sticks straight up at the back of the carburetor. Turn the
needle counterclockwise for a richer air/fuel mixture and clockwise for a leaner air/
fuel mixture. An overly rich mixture will yield sluggish acceleration and performance
with thick smoke from the exhaust. A lean mixture can cause the engine to hesitate
before accelerating or, in some cases, to lose power momentarily after the initial
acceleration. A lean mixture also makes the engine run too hot and does not provide
enough lubrication for the internal engine components, causing premature wear and
damage. Run the engine slightly rich and never lean to avoid overheating and
possible damage. See: Vehicle Tuning.
Fuel Safety and Use Instructions
Fueling the Vehicle
Understanding Rich and Lean Fuel Mixture
Lift the fuel tank cap and fill the fuel tank. Press the fuel tank cap down securely.
WARNING: Fuel is highly flammable. Always follow all safety precautions
during use.
• Maintain sight of the vehicle at all times.
• Inspect the vehicle for loose wheel hardware.
• Inspect the steering assembly for any loose hardware.
• Stop driving the vehicle when you notice a lack of power. Driving the vehicle
when the battery is discharged can cause the receiver to power off. You may
lose control of the vehicle.
• Do not apply the throttle in forward if the vehicle is stuck. Applying throttle in
this instance can damage the engine.
• Allow the engine to cool to ambiant temperature between runs.
Starting Procedure
1. Turn on the transmitter.
2. Turn on the receiver.
3. Lock the glow igniter onto the glow plug.
4. Pull the starter cord in a quick continuous motion to start the engine. Do not pull the starter cord over 6 inches.
1
ON
2
ON
4
PULL
3
LOCK

LOSI 8IGHT/8IGHT-T RTR • INSTRUCTION MANUAL
6
EN
Break-In Procedure
CAUTION: Complete the break-in process on a smooth surface, such as
pavement or concrete. Do not drive the vehicle on dirt or grass during the
break-in process as doing so will damage the engine.
Run the first three tanks of fuel with the high and low speed needles noticeably rich (see
Understanding Rich and Lean Fuel Mixture).There should be a slight sluggishness
and thick smoke when accelerating. The smoke will decrease as the vehicle gains
speed. At speed, there should still be a noticeable trail of smoke from the exhaust pipe.
Run the vehicle on a flat surface in a Figure 8 pattern. Ease into the throttle as you
accelerate on the straight sections, easing off as you approach turns and letting the
vehicle roll through the turn before easing back on the throttle. This will allow you to get
a feel for the steering response and handling characteristics of the vehicle.
Engine Break-In
Breaking in your new engine is critical for proper performance. Failure to follow the break-in procedures can cause engine damage and shortened engine life. Always use
Losi®Nitrotane 20% Sport Fuel during the break-in process and when running the engine.
Although the carburetor is pre-adjusted at the factory, familiarize yourself with the following adjustments and break-in procedures. If you change fuel or environments (i.e.,
hotter/colder temperatures, higher/lower elevation, etc.) you may have to adjust at least the high-speed needle to prevent overheating and maintain proper performance.
Never, under any circumstances, allow the engine to rev freely with the wheels off the ground.
Use the optional Dynamite Pro Temp Gun with Laser Sight (DYNP2000) to check engine temperatures.
Before Making Adjustments
• Ensure there are no leaks or obstructions in the fuel tank, fuel tubing
or the carburetor. Any faults can affect engine operation and tuning.
• The carburetor needle is very sensitive. Adjusting the needle even 1/12
of a turn is a significant change. Be careful when making adjustments.
• Ensure the engine has reached running temperature before making
carburetor adjustments.
NOTICE: When making adjustments, only turn the needle 1/12 turn at a time.
Carb Adjustments
Make all carburetor adjustments in
one-hour increments.
Imagine the slot in the needle is the
hour hand on a clock. Adjust it as
though you were moving the hour
hand from one hour to the next or
previous one.
Factory Needle Settings
Low Speed Needle: 42 hours from the bottom
High Speed Needle: 39 hours from the bottom
2 hour
1 hour
After you break in the engine, you can tune it for optimum performance. Use caution not to overheat the engine, as severe damage and pre-mature wear can occur. Make all
carburetor adjustments in “one hour” increments. If your engine is not running properly, return the carburetor to factory settings. See the illustrations below.
Engine Tuning
Idle Needle (Bottom of carburetor).
The idle needle controls the idle
speed of the engine with no radio
input. Turning the needle clockwise
raises the idle. Turning the needle
counterclockwise lowers the idle.
High-Speed Needle (top, Right
side). Close the high-speed needle
by turning it clockwise until it stops,
then turn it counterclockwise 39
hours from the bottom (open).
Low-Speed Needle
(on the Left side). Close
the low-speed needle
by turning it clockwise
until it stops, then turn it
counterclockwise 42 hours
from the bottom (open).
1/16 – 3/16 inch gap

EN
7
LOSI 8IGHT/8IGHT-T RTR • INSTRUCTION MANUAL
NOTICE: Measure engine temperatures at the top of the head.
Low-Speed Adjustment
The low-speed adjustment affects the idle and slightly-off-idle performance. The model
should accelerate with a slight amount of sluggishness and a noticeable amount of
smoke.The simplest way to check this is to make sure the engine has been warmed up
and let the engine idle for 8−10 seconds. If the low-speed mixture is so far off that the
engine won’t stay running that long, turn the idle-speed screw clockwise, increasing
the idle speed. With the engine at idle, pinch and hold the fuel line near the carburetor,
cutting off the flow of fuel, and listen closely to the engine rpm (speed). If the low-speed
needle is set correctly, the engine speed will increase only slightly and then die. If the
engine increases several hundred rpm before stopping, the low-speed needle is too
rich. Lean the mixture by turning the needle clockwise one hour and trying again. If the
engine speed does not increase but simply dies, the needle is too lean and needs to be
enriched up by turning the needle counterclockwise one hour before trying again. After
you have optimized the low-speed setting, the engine will probably be idling faster. You
will have to adjust the idle-speed screw counterclockwise to slow the engine idle speed
down. The engine should accelerate at a constant pace without hesitating.
High-Speed Adjustment
After initial acceleration, the engine should pull at a steady rate while maintaining a
two-stroke whine and a noticeable trail of smoke. If the engine labors and is sluggish
with heavy smoke, the mixture is too rich and needs to be leaned by turning the high-
speed needle clockwise in one-hour increments until it runs smoothly. If the engine
isn’t smoking or starts to die after acceleration, it is too lean and you must enrich the
mixture by turning the needle counterclockwise. Don’t be confused by the sound of the
engine and the actual performance. A leaner mixture will produce an exhaust note with
a higher pitch but this does not necessarily mean improved performance, as the engine
is on the verge of overheating and may incur possible damage. Ideally you want to run
the engine so that it is on the slightly rich side of optimum. This will give you the best
combination of speed and engine life.
NOTICE: The engine is too lean and overheating if it accelerates rapidly with
a high-pitched scream then seems to labor, stops smoking, or loses speed.
This can be caused by the terrain, atmospheric conditions, or drastic altitude
changes. To avoid permanent engine damage, immediately adjust the mixture
by turning the high-speed needle counterclockwise at least “two hours” and be
prepared for further adjustments before running any more.
Engine Tuning
Testing the Temperature
In order to obtain an accurate temperature reading from the engine, stop the car in
a safe area, and let the engine idle for 10 seconds. Once the temperature stabilizes,
this is the true engine temperature. The ideal operating temperature for the engine
will vary with the air temperature but, in general, it should fall within the 220–265°F
(104–129°C) range. A simple way to check the engine temperature is to put a few
drops of water on the top of the head/heat sink. It should take 3−5 seconds for the
water to evaporate. If it boils away quickly, the engine is overheating and the high-
speed needle needs adjusted (turned counterclockwise) at least two hours. The engine
runs cooler while driving because air is passing through the fins on the head, thereby
cooling the engine.
Low-Speed Needle
As you turn this clockwise (leaner), less fuel enters the engine. Turning it
counterclockwise (richer) allows more fuel to enter the engine.
Richer Leaner
High-Speed Needle
As you turn this clockwise (leaner), less fuel enters the engine. Turning
it counterclockwise (richer) allows more fuel to enter the engine.
Idle-Speed Adjustment
As you turn this clockwise, the carburetor opens wider at idle thereby
increasing idle speed. Turning it counterclockwise decreases the
opening and decreases idle speed.
Richer
Slower
Faster
Leaner

LOSI 8IGHT/8IGHT-T RTR • INSTRUCTION MANUAL
8
EN
Possible Cause Solution
ENGINE DOES NOT START
Out of fuel Refill the tank and follow starting instructions
Engine flooded Review Glow Plug Test
Air filter is clogged Check and replace if necessary
Fuel is old or bad Use new fuel
Glow plug is not working Review Glow Plug Test
Throttle servo failed/Setup is wrong Check servo operation. Set it to neutral and reset the linkage according
to your radio and model manufacturer’s specifications
Carburetor is incorrectly adjusted Return the carburetor to the factory settings and retune if necessary
Piston and cylinder is worn Check the piston and cylinder for wear or damage and replace if necessary
ENGINE STARTS THEN STALLS
Out of fuel Refill the tank and follow starting instructions
Air filter is clogged Check and replace if necessary
Engine may be overheated Let the engine cool. Richen the high speed needle
Engine idle is too low Follow the instructions to increase idle speed
Carburetor is incorrectly adjusted Return the carburetor to the factory settings and retune if necessary
Clutch is slipping or locked-up Check the clutch for worn/broken shoe or spring. Also check clutch
bearings and ensure free rotation
Fuel is old or bad Use new fuel
ENGINE IS RUNNING, BUT VEHICLE DOES NOT MOVE
Brakes are stuck Look for damage or foreign matter locking the brakes
Drivetrain is damaged Check for damaged driveshaft or diff. Replace as needed
Receiver battery capacity is low Charge the receiver battery
Radio is not responding despite charged battery Make sure binding is properly set up
Throttle servo is improperly set up Set the servo to neutral and reset the linkage according to radio and model
manufacturer’s specifications
Drivetrain is not functioning properly Check the drivetrain for smooth operation/damage
ERRATIC CONTROL
Transmitter and/or receiver batteries are weak Install new batteries in the transmitter. Recharge the receiver battery
Connectors are inserted improperly Check the connectors and reinstall if necessary
Brake is not working Check the servo, brakes, and linkage for damage. Repair/replace/reset
the servo linkage to factory settings
The throttle channel was reversed after calibration Rebind and calibrate
The steering channel was reversed after calibration Rebind and calibrate
Troubleshooting Guide
Turning Off the Vehicle
1. Remove the vehicle body.
2. Using a Losi®tuning screwdriver (LOSA99167), pinch the fuel line.
3. Power off the receiver.
4. Power off the transmitter.
WARNING: Do not touch the exhaust, as it can become extremely hot
during use.
1
OFF
2
OFF

EN
9
LOSI 8IGHT/8IGHT-T RTR • INSTRUCTION MANUAL
Binding and Calibrating the Receiver
Changing the Travel Adjust Settings
Maintenance and Troubleshooting
The included transmitter and receiver are bound at the factory. To rebind:
1. Power off the transmitter and receiver.
2. Insert the bind plug into the BIND port on the receiver.
3. Power on the receiver. The LED in the receiver flashes rapidly, indicating that the
receiver is in bind mode.
4. With the throttle in neutral, power on the transmitter while pressing the bind
button. The LED in the receiver turns solid when binding is complete.
5. Remove the bind plug from the receiver after binding is complete.
You must rebind when binding the receiver to a different transmitter.
NOTICE: Do not attempt to bind the transmitter and receiver if there
are other compatible transmitters in bind mode within 400 feet. Doing
so may result in unexpected binding.
Failsafe
In the unlikely event that the radio connection is lost during use, the receiver will
drive the servos to their failsafe positions (the bind settins are the failsafe settings).
If the receiver is powered on before powering on the transmitter, the receiver will
enter this failsafe mode. When the transmitter is powered on, normal control is
resumed.
IMPORTANT: Failsafe activates only in the event that signal is lost from the
transmitter. Failsafe will NOT activate in the event that receiver battery power
decreases below the recommended minimums or power to the receiver is lost.
The travel function supports precise endpoint adjustments in each direction for the
steering and throttle channels. Ensure the ST RATE knob is all the way up.
1. Hold the trigger in the full brake position and steering wheel in the full right
position while powering on the transmitter. The LED flashes rapidly, indicating
the programming mode is active.
2. Throttle End Point: Hold the trigger in the full throttle position. Turn the TH
TRIM knob to adjust the full throttle end point.
3. Brake End Point: Hold the trigger in the full brake position. Turn the TH TRIM
knob to adjust the full brake end point. Return the trigger to the center position.
4. Left Steering End Point: Hold the steering wheel in the full left position. Turn
the ST TRIM knob to adjust the left end point.
5. Right Steering End Point: Hold the steering wheel in the full right position.
Turn the ST TRIM knob to adjust the right end point. Return the steering
wheel to the center position.
6. Power off the transmitter to save the travel adjust settings. The minimum
travel is 75% and the maximum travel is 150%. The default travel settings
are 125% steering and 100% throttle.
Adjusting Steering and Throttle Trims
Steering Trim
The model should go straight without turning the steering wheel. If not,
turn the ST TRIM knob in the direction needed for the model to go straight.

LOSI 8IGHT/8IGHT-T RTR • INSTRUCTION MANUAL
10
EN
Maintenance and Troubleshooting
The Dynamite®glow plug used with your engine (DYN2495) is designed specifically
for the engine.
CAUTION: Before testing the glow plug, clean up spilled fuel and close
fuel containers. Failure to do can result in injury, fire or damage.
Use a spare glow plug to check the igniter. If the igniter makes the element glow,
remove the plug from the engine to check it the same way. Reinstall the glow plug,
maing sure you have included the brass gasket. Or, install a new glow plug (DYN2495)
with the required brass gasket.
A wet glow plug indicates there is excess fuel in the engine. To
eliminate the excess fuel:
1. Remove the glow plug.
2. Place the model on a stand where the tires are not
touching the ground and place a rag over the cylinder
head.
3. Turn the engine over for a few seconds. This will
remove the excess fuel in the engine.
Glow Plug Test
tooltip
A
Throttle Trim
Adjust the TH TRIM so the carburetor is completely closed when the throttle trigger
is at neutral. If throttle cannot be closed using TH TRIM, please take the following
steps:
1. Make sure TH TRIM knob is set to “0” or neutral.
2. Loosen the drum barrel (A) at the end of the assembly with a hex wrench.
3. Allow the carburetor slide to close completely.
4. Tighten the drum barrel at the end of the assembly.
NOTICE: Throttle trim change may affect engine operation. Carburetor settings
must be set correctly or damage may result.
See Engine Tuning for carburetor adjustments.
Forward
Brake

EN
11
LOSI 8IGHT/8IGHT-T RTR • INSTRUCTION MANUAL
What this Warranty Covers
Horizon Hobby, LLC, (Horizon) warrants to the original purchaser that the product
purchased (the “Product”) will be free from defects in materials and workmanship at
the date of purchase.
What is Not Covered
This warranty is not transferable and does not cover (i) cosmetic damage, (ii) damage
due to acts of God, accident, misuse, abuse, negligence, commercial use, or due to
improper use, installation, operation or maintenance, (iii) modification of or to any part
of the Product, (iv) attempted service by anyone other than a Horizon Hobby authorized
service center, (v) Product not purchased from an authorized Horizon dealer, or (vi)
Product not compliant with applicable technical regulations or (vii) use that violates
any applicable laws, rules, or regulations.
OTHER THAN THE EXPRESS WARRANTY ABOVE, HORIZON MAKES NO OTHER
WARRANTY OR REPRESENTATION, AND HEREBY DISCLAIMS ANY AND ALL IMPLIED
WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES
OF NON-INFRINGEMENT, MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. THE PURCHASER ACKNOWLEDGES THAT THEY ALONE HAVE DETERMINED
THAT THE PRODUCT WILL SUITABLY MEET THE REQUIREMENTS OF THE
PURCHASER’S INTENDED USE.
Purchaser’s Remedy
Horizon’s sole obligation and purchaser’s sole and exclusive remedy shall be that
Horizon will, at its option, either (i) service, or (ii) replace, any Product determined by
Horizon to be defective. Horizon reserves the right to inspect any and all Product(s)
involved in a warranty claim. Service or replacement decisions are at the sole
discretion of Horizon. Proof of purchase is required for all warranty claims. SERVICE
OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE PURCHASER’S
SOLE AND EXCLUSIVE REMEDY.
Limitation of Liability
HORIZON SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL OR
CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL
LOSS IN ANY WAY, REGARDLESS OF WHETHER SUCH CLAIM IS BASED IN CONTRACT,
WARRANTY, TORT, NEGLIGENCE, STRICT LIABILITY OR ANY OTHER THEORY OF
LIABILITY, EVEN IF HORIZON HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH
DAMAGES. Further, in no event shall the liability of Horizon exceed the individual price
of the Product on which liability is asserted. As Horizon has no control over use, setup,
final assembly, modification or misuse, no liability shall be assumed nor accepted for
any resulting damage or injury. By the act of use, setup or assembly, the user accepts
all resulting liability. If you as the purchaser or user are not prepared to accept the
liability associated with the use of the Product, purchaser is advised to return the
Product immediately in new and unused condition to the place of purchase.
Law
These terms are governed by Illinois law (without regard to conflict of law principals).
This warranty gives you specific legal rights, and you may also have other rights which
vary from state to state. Horizon reserves the right to change or modify this warranty
at any time without notice.
WARRANTY SERVICES
Questions, Assistance, and Services
Your local hobby store and/or place of purchase cannot provide warranty support
or service. Once assembly, setup or use of the Product has been started, you must
contact your local distributor or Horizon directly. This will enable Horizon to better
answer your questions and service you in the event that you may need any assistance.
For questions or assistance, please visit our website at www.horizonhobby.com,
submit a Product Support Inquiry, or call the toll free telephone number referenced in
the Warranty and Service Contact Information section to speak with a Product Support
representative.
Inspection or Services
If this Product needs to be inspected or serviced and is compliant in the country you
live and use the Product in, please use the Horizon Online Service Request submission
process found on our website or call Horizon to obtain a Return Merchandise
Authorization (RMA) number. Pack the Product securely using a shipping carton.
Please note that original boxes may be included, but are not designed to withstand
the rigors of shipping without additional protection. Ship via a carrier that provides
tracking and insurance for lost or damaged parcels, as Horizon is not responsible for
merchandise until it arrives and is accepted at our facility. An Online Service Request
is available at http://www.horizonhobby.com/content/service-center_render-service-
center. If you do not have internet access, please contact Horizon Product Support to
obtain a RMA number along with instructions for submitting your product for service.
When calling Horizon, you will be asked to provide your complete name, street
address, email address and phone number where you can be reached during business
hours. When sending product into Horizon, please include your RMA number, a list of
the included items, and a brief summary of the problem. A copy of your original sales
receipt must be included for warranty consideration. Be sure your name, address, and
RMA number are clearly written on the outside of the shipping carton.
NOTICE: Do not ship Li-Po batteries to Horizon. If you have any issue
with a Li-Po battery, please contact the appropriate Horizon Product
Support office.
Warranty Requirements
For Warranty consideration, you must include your original sales receipt verifying the
proof-of-purchase date. Provided warranty conditions have been met, your Product
will be serviced or replaced free of charge. Service or replacement decisions are at
the sole discretion of Horizon.
Non-Warranty Service
Should your service not be covered by warranty, service will be completed and
payment will be required without notification or estimate of the expense unless the
expense exceeds 50% of the retail purchase cost. By submitting the item for service
you are agreeing to payment of the service without notification. Service estimates are
available upon request. You must include this request with your item submitted for
service. Non-warranty service estimates will be billed a minimum of ½ hour of labor.
In addition you will be billed for return freight. Horizon accepts money orders and
cashier’s checks, as well as Visa, MasterCard, American Express, and Discover cards.
By submitting any item to Horizon for service, you are agreeing to Horizon’s Terms
and Conditions found on our website http://www.horizonhobby.com/content/service-
center_render-service-center.
ATTENTION: Horizon service is limited to Product compliant in the
country of use and ownership. If received, a non-compliant Product
will not be serviced. Further, the sender will be responsible for
arranging return shipment of the un-serviced Product, through a
carrier of the sender’s choice and at the sender’s expense. Horizon will
hold non-compliant Product for a period of 60 days from notification,
after which it will be discarded.
10/15
Limited Warranty

LOSI 8IGHT/8IGHT-T RTR • INSTRUCTION MANUAL
12
EN
Warranty and Service Contact Information
Country of
Purchase Horizon Hobby Contact Information Address
United States of America
Horizon Service Center
(Repairs and Repair Requests)
servicecenter.horizonhobby.com/
RequestForm/
4105 Fieldstone Rd
Champaign, Illinois, 61822 USA
Horizon Product Support
(Product Technical Assistance)
[e-mail]
877-504-0233
Sales [e-mail]
800-338-4639
United Kingdom Service/Parts/Sales:
Horizon Hobby Limited
[e-mail] Units 1–4 , Ployters Rd, Staple Tye
Harlow, Essex, CM18 7NS, United Kingdom
[phone]
Germany Horizon Technischer Service [e-mail] Christian-Junge-Straße 1
25337 Elmshorn, Germany
Sales: Horizon Hobby GmbH [phone]
France Service/Parts/Sales:
Horizon Hobby SAS
[e-mail] 11 Rue Georges Charpak
77127 Lieusaint, France
[phone]
FCC Statement
FCC Number: BRWDASRX18 This device complies with part 15 of the FCC rules.
Operation is subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
CAUTION: Changes or modifications not expressly approved by the
party responsible for compliance could void the user’s authority to
operate the equipment.
This product contains a radio transmitter with wireless technology which has been
tested and found to be compliant with the applicable regulations governing a radio
transmitter in the 2.400GHz to 2.4835GHz frequency range.
Antenna Separation Distance
When operating your Spektrum
transmitter, please be sure to
maintain a separation distance
of at least 5 cm between your
body (excluding fingers, hands,
wrists, ankles and feet) and the
antenna to meet RF exposure
safety requirements as deter-
mined by FCC regulations.
The following illustrations show
the approximate 5 cm RF exposure area and typical hand placement when operating
your Spektrum transmitter.
IC Information
IC Number: 6157 A-ASRX18 This device complies with Industry Canada licence-
exempt RSS standard(s). Operation is subject to the following two conditions: (1) this
device may not cause interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of the device.
EU Compliance Statement: Horizon Hobby, LLC hereby declares that this
product is in compliance with the essential requirements and other relevant
provisions of the R&TTE, EMC, and LVD Directives.
A copy of the EU Declaration of Conformity is available online at:
http://www.horizonhobby.com/content/support-render-compliance.
Instructions for disposal of WEEE by users
in the European Union
This product must not be disposed of with other waste. Instead, it is the user’s
responsibility to dispose of their waste equipment by handing it over to a
designated collections point for the recycling of waste electrical and electronic equipment.
The separate collection and recycling of your waste equipment at the time of disposal will
help to conserve natural resources and ensure that it is recycled in a manner that protects
human health and the environment. For more information about where you can drop off
your waste equipment for recycling, please contact your local city office, your household
waste disposal service or where you purchased the product.

43
LOSI 8IGHT/8IGHT-T RTR
Front: Standard Smart
Differentials
Wing Type:
Wing Spacer:
Wicker Bill:
43
LOSI 8IGHT/8IGHT-T RTR

LOSI 8IGHT/8IGHT-T RTR
44
Front: Standard Smart
Differentials
Wing Type:
Wing Spacer:
Wicker Bill:
3000 wt
Long
2º Toe Out
-1º
2.3mm
54mm/40 wt
Silver
95mm
2/Outside
Up
3
27mm
8IGHT Standard Setup
3º
3º
29mm
-2º
Back
2–3mm
54mm/40 wt
Green
106mm
1B
2/Outside
Stock
7000 wt
5000 wt
Standard
Standard
x
20% Sport
4 composite
4 black springs
Aluminium Flywheel
XBT
XBT
Blue
Blue
Losi
Losi
Stock
50/17
Dynamite .21
Medium
Dynamite
x
6V/NiMH
x

45
LOSI 8IGHT/8IGHT-T RTR
Front: Standard Smart
Differentials
Wing Type:
Wing Spacer:
Wicker Bill:

LOSI 8IGHT/8IGHT-T RTR
46
Front: Standard Smart
Differentials
Wing Type:
Wing Spacer:
Wicker Bill:
3000 wt
Long
2º Toe Out
-1º
2.3mm
54mm/70 wt
Black
110mm
2/Outside
Up
3
39mm
8IGHT-T Standard Setup
3.5º
3º
42mm
-2º
Back
2–33mm
54mm/70 wt
Grey
130mm
2B
2/Outside
Stock
7000 wt
5000 wt
Standard
Standard
x
20% Sport
4 composite
4 black springs
Aluminium Flywheel
XTT
XTT
Blue
Blue
Losi
Losi
Stock
50/13
Dynamite .28
Medium
Dynamite
x
6V/NiMH

47
LOSI 8IGHT/8IGHT-T RTR
Part # English Deutsch Français Italiano
DYNE0570 .21 RTR Engine W/PS .21 RTR Motor W/PS Moteur RTR .21 avec cordon de démarrage Motore W/PS .21 RTR
DYNE0571 .28 RTR Engine W/PS .28 RTR Motor W/PS Moteur RTR .28 avec cordon de démarrage Motore W/PS .28 RTR
DYNE1505 Exhaust Pipe Assembly: .21 8 & .28 8T RTR Auspuffkit: .21 8 und .28 8T RTR .21 8 & .28 8T RTR - Échappement Gruppo marmitta: .21 8 e .28 8T RTR
JSP98010 Standard Switch Standardschalter Interrupteur Standard Interruttore standard
LOS240007 Body, Painted, Nitro: 8IGHT RTR Karosserie, lackiert, Nitro: 8IGHT RTR 8IGHT RTR - Carrosserie, peinte, Nitro Carrozzeria, verniciata, nitro: 8IGHT RTR
LOS240008 Body, Painted, Nitro: 8IGHT-T RTR Karosserie, lackiert, Nitro: 8IGHT-T RTR 8IGHT-T RTR - Carrosserie, peinte, Nitro Carrozzeria, verniciata, nitro: 8IGHT-T RTR
LOS241013 Chassis: 8IGHT RTR Chassis: 8IGHT RTR 8IGHT RTR - Châssis Telaio: 8IGHT RTR
LOS241014 Chassis: 8IGHT-T RTR Chassis: 8IGHT-T RTR 8IGHT-T RTR - Châssis Telaio: 8IGHT-T RTR
LOS241015 Engine Mounts: 8IGHT, 8IGHT-T RTR Motorlager: 8IGHT, 8IGHT-T RTR 8IGHT, 8IGHT-T RTR - Supports moteur Supporti motore: 8IGHT, 8IGHT-T RTR
LOS242001 Rear Dogbone & Axle Set: 8T 3.0 8T 3.0: Radachse Hinten (2) 8T 3.0 - Tige + axe de cardan arrière (2) Set giunto cardanico posteriore e asse: 8T 3.0
LOS242012 Spur Gear, 50T: 8IGHT, 8IGHT-T RTR Stirnradgetriebe, 50T: 8IGHT, 8IGHT-T RTR 8IGHT, 8IGHT-T RTR - Couronne 50T Ingranaggio cilindrico, 50T: 8IGHT, 8IGHT-T RTR
LOS242013 Front 47T Diff Gear & 12T Pinion: 8IGHT, 8IGHT-T
RTR
Front 47T Diff. Getriebe & 12T Ritzel: 8IGHT, 8IGHT-T
RTR
8IGHT, 8IGHT-T RTR - Différentiel avant 47T et
pignon 12T
Ingranaggio differenziale 47T anteriore e pignone
12T: 8IGHT, 8IGHT-T RTR
LOS242014 Rear 47T Diff Gear & 12T Pinion: 8IGHT, 8IGHT-T
RTR
Heck 47T Diff. Getriebe & 12T Ritzel: 8IGHT, 8IGHT-T
RTR
8IGHT, 8IGHT-T RTR - Différentiel arrière 47T et
pignon 12T
Ingranaggio differenziale 47T posteriore e pignone
12T: 8IGHT, 8IGHT-T RTR
LOS242015 Differential Case & Hardware: 8IGHT, 8IGHT-T RTR Ausgleichsgehäuse und Bauteile: 8IGHT, 8IGHT-T RTR 8IGHT, 8IGHT-T RTR - Corps de différentiel Scatola differenziale e accessori: 8IGHT, 8IGHT-T RTR
LOS242016 Center Outdrives: 8IGHT, 8IGHT-T RTR Mittlere Outdrives: 8IGHT, 8IGHT-T RTR 8IGHT, 8IGHT-T RTR - Noix de cardans centraux Trascinatori centrali: 8IGHT, 8IGHT-T RTR
LOS242017 Front/Rear Outdrives: 8IGHT, 8IGHT-T RTR Front/Heck-Outdrives: 8IGHT, 8IGHT-T RTR 8IGHT, 8IGHT-T RTR - Noix de cardans avant/arrière Trascinatori anteriori/posteriori: 8IGHT, 8IGHT-T RTR
LOS243002 15mm Front Shock Body (2): 8IGHT RTR 15mm Frontstoßdampfer (2): 8IGHT RTR 8IGHT RTR - Corps d’amortisseurs avant 15mm (2) Corpo ammortizzatore anteriore 15 mm (2): 8IGHT RTR
LOS243003 15mm Front Shock Body (2): 8IGHT-T RTR 15mm Frontstoßdampfer (2): 8IGHT-T RTR 8IGHT-T RTR - Corps d’amortisseurs arrière 15mm (2) Corpo ammortizzatore anteriore 15 mm (2): 8IGHT-T RTR
LOS243004 8T Front, 8 Rear Shock Body (2): 8IGHT, 8IGHT-T
RTR
8T Front, 8 Heck Stoßdämpfer (2): 8IGHT, 8IGHT-T
RTR
8IGHT, 8IGHT-T RTR - Corps d’amortisseur avant 8T
et arrière 8 (2)
Corpo ammortizzatore anteriore 8T, posteriore 8 (2):
8IGHT, 8IGHT-T RTR
LOS243005 Shock Caps (2): 8IGHT, 8IGHT-T RTR Stoßdämpferkappe (2): 8IGHT, 8IGHT-T RTR 8IGHT, 8IGHT-T RTR - Bouchon d’amortisseurs (2) Tappi ammortizzatore (2): 8IGHT, 8IGHT-T RTR
LOS244000 Link Set: 8IGHT RTR Kupplung Set: 8IGHT RTR 8IGHT RTR - Biellettes Set collegamenti: 8IGHT RTR
LOS244001 Link Set: 8IGHT-T RTR Kupplung Set: 8IGHT-T RTR 8IGHT-T RTR - Biellettes Set collegamenti: 8IGHT-T RTR
LOSA1701 Front Suspension Arm Bushings: 8B, 8T Buchse für Querlenker vorne: 8B, 8T 8B/8T - Paliers de triangles avant Boccole braccio sospensione anteriore: 8B, 8T
LOSA1731 Rear Hub Carriers: 8B 2.0 Heck-Radträger: 8B 2.0 8B 2.0 - Porte moyeux arrière Supporti hub posteriore: 8B 2.0
LOSA1732 Rear Hub Carriers, Aluminum: 8B, 8T 2.0 Heck-Radträger, Aluminium: 8B, 8T 2.0 8B, 8T 2.0 - Porte moyeux arrière alu Supporti hub posteriore, alluminio: 8B, 8T 2.0
LOSA1750 Sway Bar Set: 8B,8T Stabilisator Set: 8B,8T 8B, 8T - Set de barre anti-roulis Set barra antitorsione: 8B,8T
LOSA1751 Sway Bar Set: 8B 2.0 Stabilisator Set: 8B 2.0 8B 2.0 - Set de barre anti-roulis Set barra antitorsione: 8B 2.0
LOSA3518 Drive Pin Set: 8B/8T Mitnehmerstift Set: 8B/8T 8B/8T - Goupilles Set perni trasmissione: 8B/8T
LOSA3522 F/R CV Driveshaft Axles (2): 8B,8T F/R CV Achsen der Antriebswellen (2): 8B,8T 8B, 8T - Axes de cardans av/arr. CV (2) Assi trasmissione F/R CV (2): 8B,8T
LOSA3523 F/R CV Driveshaft Coupling Set: 8B,8T F/R CV Antriebwellen-Kupplung Set: 8B,8T 8B, 8T - Coupleurs de cardans av/arr. CV Set accoppiamento trasmissione F/R CV: 8B, 8T
LOSA3530 Wheel Hexes (Pr) Hard Anodized: 8B,8T Rad-Sechskantstücke (Pr) harteloxiert: 8B,8T 8B, 8T - Hexagone de jantes anodisé dur (Pr) Esagoni ruote (Pr) anodizzati duri: 8B, 8T
LOSA3531 Wheel Nuts and Pins (4ea.): 8B, 8T Losi Radmutter und Stifte (je 4): 8B/8T 8B, 8T - Ecrous de jantes & goupilles (4ea) Dadi e perni ruota (4 cadauno): 8B, 8T
LOSA3535 Front/Rear CV Drive Shafts (2): 8B 2.0 Front/Heck CV Antriebswellen (2): 8B 2.0 8B 2.0 - Arbres av./arr.CV (2) Albero di trasmissione CV anteriore/posteriore (2): 8B 2.0
LOSA3544 Brake Cam Set: 8B,8T Bremsnocken Set: 8B,8T 8B, 8T- Set de came de frein Set camma freno: 8B,8T
LOSA3545 Brake Disk Set: 8B 2.0 Bremsscheiben Set: 8B 2.0 8B 2.0 - Set de disque Set disco freno: 8B 2.0
LOSA3546 Brake Pads & Screws: 8B 2.0 Bremsbeläge & Schrauben: 8B 2.0 8B 2.0 - Plaquettes de frein & écrous Viti e pastiglie freno: 8B 2.0
LOSA3586 Front/Rear CV Drive Shaft Set (2): 8T 2.0 Front/Heck CV Antriebswelle Set (2): 8T 2.0 8T 2.0 - Set arbre av./arr.CV (2) Set trasmissione CV anteriore/posteriore (2): 8T 2.0
LOSA4002 Antenna Kit Antennenkit Kit antenne Kit antenna
LOSA4003 Antenna Caps Antennenkappe Embouts d’antenne Tappi antenna
LOSA4406 Steering Bellcrank Plastics & Servo Saver: 2.0 Kunststoffteile des Lenkwinkelhebels & Servo-Saver:
2.0
2.0 - Palonnier de direction, plastics & Sauve servo Squadrette sterzo plastica e salvaservo: 2.0
LOSA4408 Steering Post Set: 8B,8T Lenksäule Set: 8B,8T 8B, 8T - Set de pivot de direction Set comandi sterzo: 8B, 8T
LOSA4412 Steering Rack Set, Short/Long: 8B 2.0 Losi Lenkhebel kurz/lang: 8B 2.0 8B 2.0 - Barre de direction, Short/Long Cremagliera sterzo, corta/lunga: 8B 2.0
LOSA4413 Front Chassis Brace Set: 8B,8T Front-Chassis-Strebe Set: 8B,8T 8B, 8T - Châssis entretoises av. Set trapezio anteriore: 8B, 8T
LOSA4414 Rear Chassis Brace: 8B,8T Heck-Chassis-Strebe Set: 8B,8T 8B, 8T - Châssis entretoise arr. Trapezio posteriore: 8B, 8T
LOSA4419 Switch Cover & Foam Pad: 8B, 8T Schalterabdeckung & Schaumstoffunterlage: 8B, 8T 8B, 8T - Capot d’inter. étanche Copertura interruttore e gomma: 8B, 8T
LOSA4420 Center Differential Mount & Brace Set: 8B 2.0 Mittleres Differentialgetriebe, Set mit
Halterungen & Spreize: 8B 2.0
8B 2.0 - Support de diff cent. & entretoises Set supporti diff. e tutori: 8B 2.0
LOSA4422 FR Bumper,Tank, Filter Guard: 8B, 8T FR Dämpfer, Tank, Filterschutz: 8B, 8T 8B, 8T - Pare choc av, réservoir, protection de filtre Paraurti anteriore, serbatoio, protezione filtro: 8B, 8T
LOSA4424 Body Posts & Tank Mounts: 8B, 8T Karosseriestifts & Tankhalterungen: 8B, 8T 8B, 8T - Plots de carrosserie & support de réservoir Supporti carrozzeria e supporti serbatoio: 8B, 8T
LOSA4431 Hinge Pin Brace Cover Set: 8B, 8T Hinge Pin Brace Cover Set: 8B, 8T 8B, 8T - Support d’axes Set protezioni piastrine: 8B, 8T
LOSA4432 Chassis Guard Set: 8B 2.0 Chassis-Seitenschutz Set: 8B 2.0 8B 2.0 - Protection de châssis Set protezione telaio: 8B 2.0
LOSA4435 Wing Mount Set: 8B, 8T Flügelhalterung Set: 8B, 8T 8B, 8T - Support d’aileron Set supporto alettone: 8B, 8T
LOSA4451 Rear Gear Box Set Locking Inserts: 8B 2.0 Getriebegehäuse hinten Locking Inserts: 8B 2.0 8B 2.0 - Carter de différentiel arr. Locking Inserts Set scatola ingran. poster. Locking Inserts: 8B 2.0
LOSA4452 Gear Box Shims (20): 8B 2.0 Getriebebox-Unterlegscheiben (20): 8B 2.0 8B 2.0 - Rondelles de calage (20) Spessori cellula (20): 8B 2.0
LOSA4453 Chassis Spacer/Cap Set: 8B 2.0 Chassis Spreizer/Kappe Set: 8B 2.0 8B 2.0 - Set entretoise/bouchon châssis Set distanziale telaio/tappi: 8B 2.0
LOSA5411 15mm Shock Shaft, 4mm x 50mm,TiNi (1): 8B, 8T 8B, 8T: Kolbenstange Vorne 4mm x 50mm TiNi (1) 8B, 8T - Tige d´amortisseur avant en titane
4x50mm (1)
15mm alberino ammortizz., 4mm x 50mm,TiNi
(1): 8B, 8T
LOSA5413 15mm Shock Shaft, 4mm x 57mm,TiNi (1): 8B, 8T 8B, 8T: Kolbenstange Vorne 4mm x 57mm TiNi (1) 8B, 8T - Tige d´amortisseur avant en titane
4x57mm (1)
15mm alberino ammortizz., 4mm x 57mm, TiNi
(1): 8B, 8T
LOSA5429 Shock O-ring Set: 8B 8T Stoßdämpferringe Set: 8B, 8T 8B 8T - Set de joints torique amortisseur Set o-ring ammortizzatori: 8B, 8T
LOSA5430 15mm Shock Bladders: 8B, 8T 8B, 8T:15mm Dämpfermembrane 8B, 8T - Membranes d´amortisseurs 15mm vesciche ammortizz.: 8B, 8T
LOSA5435 15mm Shock Ends, Cups, Bushing: 8B 2.0 15mm Stoßdämpferendstücke, Cups, Lager: 8B 2.0 8B 2.0 - 15mm Chape d’amortisseur, coupelles,
bagues
Boccole, terminali, coppe ammortizzatore
15 mm: 8B 2.0
LOSA5438 Shock Stand-Off Set (2): 8B, 8T Stoßdämpfer Stand-Off Set (2): 8B, 8T 8B, 8T - Entretoises d’amortisseurs (2) Set stand-Off ammortizzatore (2): 8B, 8T
LOSA5440 15mm Shock Piston/Guide Set: 8B, 8T Kolbenplatte und Gleitbuchse Set für 15mm
Stoßdämpfer : 8B, 8T
8B, 8T - Piston/Guide amortisseur 15mm Set piattelli e pistoni ammortizzatore 15 mm: 8B, 8T
LOSA5451 15mm Springs 2.3" x 4.4 Rate, Silver: 8B 15mm Federn 58,4 mm (2,3 Zoll) x 4,4 Rate, Silber: 8B 8B - Ressorts 15mm dureté 2,3 x 4,4, argent Molle 2,3" 15 mm x rigidezza 4,4, argento: 8B
LOSA5458 15mm Springs 3.1" x 3.1 Rate, Green: 8B 15mm Federn 78,7 mm (3,1 Zoll) x 3,1 Rate, Grün:8B 8B - Ressorts 15mm dureté 3,1 x 3,1, vert Molle 3,1" 15 mm x rigidezza 3,1, verde: 8B
LOSA5459 15mm Springs 3.1" x 3.4 Rate, Black: 8B 15mm Federn 3,1" x 3,4 Rate, Schwarz: 8B 8B - Ressorts 15mm dureté 3,1" x 3,4, noir Molle 3,1" 15 mm x rigidezza 3,4, nero: 8B
LOSA5461 15mm Springs 3.1" x 4.0 Rate, Gray 15mm Federn 3,1" x 4,0 Rate, Grau Ressorts 15mm dureté 3,1" x 4,0, gris Molle 3,1" 15 mm x rigidezza 4,0, grigio
LOSA6044 HD Rod Ends & Balls: 8B, 8T HD Spurstangenköpfe & Kugeln: 8B, 8T 8B, 8T - Billes de suspension 8,8mm flasqué Uniball e tirante sterzo: 8B, 8T
Parts Listing
Teileliste
Liste des pièces
Elenco componenti

LOSI 8IGHT/8IGHT-T RTR
48
Parts Listing
Teileliste
Liste des pièces
Elenco componenti
Part # English Deutsch Français Italiano
LOSA6045 HD Steering Link Set: 8B 2.0 HD Lenkkupplung Set: 8B 2.0 8B 2.0 - Tringlerie de direction renf. Set collegamenti sterzo HD: 8B 2.0
LOSA6048 Suspension Balls 8.8mm Flanged: 8B, 8T Achsaufhängungskugeln 8,8mm geflanscht: 8B, 8T 8B, 8T - Billes de suspension 8,8mm flasqué Sfere sospensioni flangiate 8,8 mm: 8B, 8T
LOSA6049 Suspension Balls 8.8mm: 8B, 8T Achsaufhängungskugeln 8,8mm: 8B, 8T 8B, 8T - Billes de suspension 8,8mm Sfere sospensioni 8,8 mm: 8B, 8T
LOSA6050 Steering Ball Set 6.8mm: 8B, 8T Lenkkugel Set 6,8 mm: 8B, 8T 8B, 8T - Billes de direction 6,8mm Set sfere sterzo 6,8 mm: 8B, 8T
LOSA6056 Suspension Balls 6.8mm: 8B 2.0 Achsaufhängungskugeln 6,8mm: 8B 2.0 8B 2.0 - Billes de suspension 6,8mm Sfere sospensioni 6,8 mm: 8B 2.0
LOSA6109 5mm E-Clips (12) 5mm E-Clips (12) E-Clips 5mm (12) E-clips 5 mm (12)
LOSA6201 3mm x 6mm Socket Head Screw 3mm x 6mmZoll Innensechskantschraube Vis CHC 3mm x 6mm Vite a brugola 3mm x 6mm
LOSA6204 4-40 x 1/2" Socket Head Screw 4-40 x 1/2Zoll Innensechskantschraube Vis CHC 4-40 x 1/2" Vite a brugola 4-40 x 1/2"
LOSA6206 4-40 x 3/8" Socket Head Screws (10) 4-40 x 3/8Zoll Innensechskantschrauben (10) Écrous SH 4-40 x 3/8" (10) Viti 4-40 x 3/8" (10)
LOSA6210 4-40 x 3/8" Flat Head Socket 4-40 x 3/8Zoll Zylinderkopfbuchse Vis tête plate 4-40 x 3/8" Vite a testa piatta 4-40 x 3/8"
LOSA6215 #4 Narrow Washers (10) #4 Schmale Unterlegscheiben (10) Rondelles étroites #4 (10) #4 Rondelle strette (10)
LOSA6221 4-40 x 5/8" Cap Screws Sockel4-40 x 5/8Zoll Kopfschrauben Vis CHC 4-40 x 5/8" Viti a brugola 4-40 x 5/8"
LOSA6227 Hardened Setscrews, 4-40 Gehärtete Gewindestifte, 4-40 Vis durcies 4-40 Grani induriti, 4-40
LOSA6228 Hardened Setscrews, 5-40 Gehärtete Gewindestifte, 5-40 Vis durcies 5-40 Grani induriti, 5-40
LOSA6240 5-40 x 1/2 Caphead Screw (8) 5-40 x 1/2Zoll Kopfschraube (8) Vis CHC 5-40 x 1/2 (8) Viti a brugola 5-40 x 1/2 (8)
LOSA6245 4-40 x 5/16" Button Head Screws 4-40 x 5/16Zoll Halbrundschrauben Vis tête bombée 4-40 x 5/16" Viti a testa tonda 4-40 x 5/16"
LOSA6246 2-56 x 5/8" Caphead Screw (8) 2-56 x 5/8Zoll Kopfschraube (8) Vis CHC 2-56 x 5/8 (8) Viti a brugola 2-56 x 5/8 (8)
LOSA6251 5-40 x 3/16" Setscrew (10) 5-40 x 3/16Zoll Gewindestifte mit Innensechskant-10 Vis pointeau bout plat 5-40 x 3/16" (10) Grani a punta piana 5-40 x 3/16" (10)
LOSA6255 2-56 x 1/4" Button Head Screws (10) 2-56 x 1/4Zoll Halbrundschrauben (10) Vis tête bombée 2-56 x 1/4" (10) Viti a testa tonda 2-56 x 1/4" (10)
LOSA6256 4-40 x 1/2" Button Head Cap Screw (6) 4-40 x 1/2Zoll Halbrundkopfschrauben (6) Vis tête bombée 4-40 x 1/2" (6) Viti a testa tonda 4-40 x 1/2" (6)
LOSA6262 8-32 x 1/2" FH Screws (10) 8-32 x 1/2Zoll Flachkopfschrauben (10) Vis tête plate 8-32 x 1/2" (10) Viti a testa piatta 8-32 x 1/2" (10)
LOSA6263 8-32 x 3/4" BH Screws (8) 8-32 x 3/4Zoll Halbrundschrauben (8) Vis tête bombée 8-32 x 3/4" (8) Viti a testa tonda 8-32 x 3/4" (8)
LOSA6264 8-32 x 3/8" FH Screws (8) 8-32 x 3/8Zoll Flachkopfschrauben (8) Vis tête plate 8-32 x 3/8" (8) Viti a testa piatta 8-32 x 3/8" (8)
LOSA6266 8-32 x 5/8" BH Screws 8-32 x 5/8Zoll Halbrundschrauben Vis tête bombée 8-32 x 5/8" Viti a testa tonda 8-32 x 5/8"
LOSA6270 5-40 x 3/8" Flat Head Screws (10) 5-40 x 3/8Zoll Zylinderkopfbuchse (10) Vis tête plate 5-40 x 3/8" (10) Viti a testa piatta 5-40 x 3/8" (10)
LOSA6271 5-40 x 1/2" FH Screws (10) 5-40 x 1/2Zoll Flachkopfschrauben (10) Vis tête plate 5-40 x 1/2" (10) Viti a testa piatta 5-40 x 1/2" (10)
LOSA6272 5-40 x 3/4" FH Screws (10) 5-40 x 3/4Zoll Flachkopfschrauben (10) Vis tête plate 5-40 x 3/4" (10) Viti a testa piatta 5-40 x 3/4" (10)
LOSA6273 5-40 x 7/8" FH Screws (4) 5-40 x 7/8Zoll Flachkopfschrauben (4) Vis tête plate 5-40 x 7/8" (4) Viti a testa piatta 5-40 x 7/8" (4)
LOSA6274 5-40 x 1 7/8" FH Screws (2) 5-40 x 1 7/8Zoll Flachkopfschrauben (2) Vis tête plate 5-40 x 1 7/8" (2) Viti a testa piatta 5-40 x 1 7/8" (2)
LOSA6275 5-40 X 5/8" Flat Head Screws (10) 5-40 x 5/8Zoll Zylinderkopfbuchse (10) Vis tête plate 5-40 x 5/8" (10) Viti a testa piatta 5-40 X 5/8" (10)
LOSA6277 5-40 x 3/8" BH Screws (8) 5-40 x 3/8Zoll Halbrundschrauben (8) Vis tête bombée 5-40 x 3/8" (8) Viti a testa tonda 5-40 x 3/8" (8)
LOSA6278 5-40 x 1/2" BH Screws (8) 5-40 x 1/2Zoll Halbrundschrauben (8) Vis tête bombée 5-40 x 1/2" (8) Viti a testa tonda 5-40 x 1/2" (8)
LOSA6279 5-40 x 3/4" BH Screws (8) 5-40 x 3/4Zoll Halbrundschrauben (8) Vis tête bombée 5-40 x 3/4" (8) Viti a testa tonda 5-40 x 3/4" (8)
LOSA6280 5-40 x 1" BH Screws (4) 5-40 x 1Zoll Halbrundschrauben (4) Vis tête bombée 5-40 x 1" (8) Viti a testa tonda 5-40 x 1" (4)
LOSA6281 5-40 x 20mm Button Head Screws (10) 5-40 x 20 mm Halbrundschrauben (10) Vis tête bombée 5-40 x 20mm (10) Viti a testa tonda 5-40 x 20 mm (10)
LOSA6282 5-40 x 7/8" BH Screws 5-40 x 7/8Zoll Halbrundschrauben Vis tête bombée 5-40 x 7/8" Viti a testa tonda 5-40 x 7/8"
LOSA6284 5-40 x 20mm BHS, Left Hand Thread, 8B Losi 5-40 x 20mm Rundkopfschrauben Linksgewinde (10) 8B - Vis CHC à pas inversé 5-40 x 20mm Viti a testa bombata 5-40 x 20 mm, filetto LH, 8B
LOSA6296 8-32 x 1/8" Flat Point Setscrew (8) 8-32 x 1/8Zoll Gewindestifte mit Innensechskant-8 Vis pointeau bout plat 8-32 x 1/8" (8) Grani a punta piana 8-32 x 1/8" (8)
LOSA6297 5-40 x 1/8" Flat Point Setscrew (8) 5-40 x 1/8Zoll Gewindestifte mit Innensechskant-8 Vis pointeau bout plat 5-40 x 1/8" (8) Grani a punta piana 5-40 x 1/8" (8)
LOSA6298 8-32 x 1/8" Cup Point Setscrew (8) 8-32 x 1/8Zoll Feststellschraube-8 Vis pointeau coupelle 8-32 x 1/8" (8) Grani a punta a coppa 8-32 x 1/8" (8)
LOSA6302 5-40 Locking Nuts, Steel 5-40 Sicherungsmuttern, Stahl Écrou auto-freiné acier 5-40 Dadi autobloccanti 5-40, acciaio
LOSA6306 4-40 Aluminum Mini-Nuts (10) 4-40 Aluminium Minimuttern (10) Mini-écrous alu 4-40 (10) Mini dadi in alluminio 4-40 (10)
LOSA6311 8-32 Steel Lock Nuts (10) 8-32 Stahlgegenmutter (10) Écrou auto-freiné acier 8-32 (10) Dadi autobloccanti in acciaio 8-32 (10)
LOSA6350 #4 and 1/8" Hardened Washers #4 und 1/8Zoll Gehärtete Unterlegscheiben Rondelles durcies #4 et 1/8" #4 Rondelle indurite 1/8"
LOSA6351 #8 Countersink Washers (8) #8 Unterlegscheiben, versenkt (8) Rondelles à tête fraisée #8 (8) #8 Rondelle svasate (8)
LOSA6937 5x10mm Shielded Ball Bearing (2) 5x10mm Kugellager mit Staubschutzscheibe (2) Roulements épaulés 5 x 10mm (2) Cuscinetti a sfera schermati 5x10 mm (2)
LOSA6942 8x16mm Sealed Ball Bearing (4) 8x16 Kugellager mit Gummiabdeckung (4) Roulements étanches 8x16 (4) Cuscinetti a sfera sigillati in gomma 8x16 (4)
LOSA6945 8x14x4 Rubber Sealed Ball Bearing (4) 8x14x4 Kugellager mit Gummiabdeckung (4) Roulements étanches 8x14x4 (4) Cuscinetti a sfera sigillati in gomma 8x14x4 (4)
LOSA6946 6x10x3 Rubber Sealed Ball Bearing (4) 6x10x3 Kugellager mit Gummiabdeckung (4) Roulements étanches 6x10x3 (4) Cuscinetti a sfera sigillati in gomma 6x10x3 (4)
LOSA6947 5x11x4 Rubber Sealed Ball Bearing (4) 5x11x4 Kugellager mit Gummiabdeckung (4) Roulements étanches 5x11x4 (4) Cuscinetti a sfera sigillati in gomma 5x11x4 (4)
LOSA6948 8x14x4 Flanged Rubber Seal Ball Bearing (4) 8x14x4 geflanschtes Kugellager mit Gummiabdeckung (4) Roulement a billes étanches 8x14x4 (4) Cuscinetti a sfera sigillati flangiati in gomma 8x14x4 (4)
LOSA6949 Clutch Bearing Set: 8B,8T Kupplungslager Set: 8B,8T 8B, 8T - Roulements de cloche Set cuscinetti frizione: 8B, 8T
LOSA6953 1/2 x 3/4 Rubber Sealed Ball Bearing 1/2 x 3/4 Kugellager mit Gummiabdeckung Roulements étanches 1/2 x 3/4 Cuscinetto a sfera sigillato in gomma 1/2 x 3/4
LOSA6955 5 x 13mm HD Clutch Bearings (2): 8B, 8T 5 x 13mm Kugellager (2): 8B, 8T 8B, 8T - Roulement embrayage renforcé 5 x 13mm (2) Cuscinetti frizione HD 5 x 13 mm (2): 8B, 8T
LOSA6956 12 x 18 x 4mm Ball Bearing (2) 12 x 18 x 4mm Kugellager (2) Roulements 12 x 18 x 4mm (2) Cuscinetto a sfera 12 x 18 x 4mm (2)
LOSA8130 Wing, Black 8B, 8T Flügel, Black 8B, 8T 8B, 8T - Aileron noir Alettone, nero 8B, 8T
LOSA9103 Clutch Nut & Hardware, 4 Shoe: 8B, 8T Kupplungsmutter & Teile, 4 Bremsbacken: 8B, 8T 8B, 8T - Écrou de cloche & visserie, 4 masselottes Dado frizione con accessori, 4 ceppi: 8B, 8T
LOSA9105 Flywheel & Collet, Aluminum: 8B 2.0 Schwungscheibe & Zwinge, Aluminium: 8B 2.0 8B 2.0 - Volant d’embrayage & cône, alu Volano e pinza, alluminio: 8B 2.0
LOSA9106 Clutch Pins & Hardware: 8B 2.0 Kupplungsstifte & Teile: 8B 2.0 8B 2.0 - Goupilles cloche & visserie Perni frizione con accessori: 8B 2.0
LOSA9107 Clutch Shoes (2) Composite: 8B, 8T Kupplungsbacken (2) Kompositwerkstoff: 8B, 8T 8B, 8T - Cloche masselottes (2) Composite Ceppi frizione compositi (2): 8B, 8T
LOSA9112 Clutch Springs, Black (4): 8B, 8T Kupplungsfedern, Schwarz (4): 8B, 8T 8B, 8T - Ressorts d’embrayage, noir (4) Molle frizione, nero (4): 8B, 8T
LOSA9113 Clutch Springs, Green (4): 8B, 8T Kupplungsfedern, Grün (4): 8B, 8T 8B, 8T - Ressorts d’embrayage, vert (4) Molle frizione, verde (4): 8B, 8T
LOSA9114 Clutch Springs, Gold (4): 8B, 8T Kupplungsfedern, Gold (4): 8B, 8T 8B, 8T - Ressorts d’embrayage, doré (4) Molle frizione, oro (4): 8B, 8T
LOSA9115 Clutch Springs, Silver (4): 8B, 8T Kupplungsfedern, Silber (4): 8B, 8T 8B, 8T - Ressorts d’embrayage, argenté (4) Molle frizione, argento (4): 8B, 8T
LOSA9116 Clutch Bell, 13T: 8B, 8T Kupplungsglocke, 13T: 8B, 8T 8B, 8T - Cloche d’embrayage renforcée 13T Campana frizione 13T: 8B, 8T
LOSA9121 Clutch Bell, 17T: 8B, 8T Kupplungsglocke, 17T: 8B, 8T 8B, 8T - Cloche d’embrayage renforcée 17T Campana frizione 17T: 8B, 8T
LOSA9150 Air Filter Set: 8B, 8T Luftfilter Set: 8B, 8T 8B, 8T - Set filtre à air Set filtro aria: 8B, 8T
LOSA9151 Air Filter Foams, Pre-Oiled: 8B, 8T Luftfilter Schaumstoffe, Vorgeölt: 8B, 8T 8B, 8T - Mousse filtre à air, Pré-huilé Spugna filtro aria, preoliata: 8B, 8T
LOSA9158 Fuel Tank: 8T 2.0 Kraftstofftank: 8T 2.0 8T 2.0 - Réservoir carburant Serbatoio: 8T 2.0
LOSA9162 Fuel Tank: 8B 2.0 Kraftstofftank: 8B 2.0 8B 2.0 - Réservoir carburant Serbatoio: 8B 2.0
LOSA9163 Fuel Tank Cap, Spring & Seal: 8B 2.0 Tankverschluss, Feder & Dichtung: 8B 2.0 8B 2.0 - Bouchon, ressort & joint de réservoir Tappo serbatoio, molla e guarnizione: 8B 2.0
LOSA9164 EFRA Fuel Tank Kit: 8B/8T 2.0 EFRA Kraftstoffbehälter Kit: 8B/8T 2.0 8B/8T 2.0 - Kit réservoir EFRA Kit serbatoio EFRA: 8B/8T 2.0
LOSA9165 Tuned Pipe Mount & Hardware: 8B,8T Getunte Rohrhalterung & Teile: 8B,8T 8B, 8T - Support résonateur & visserie Supporto scarico marmitta con accessori: 8B,8T

49
LOSI 8IGHT/8IGHT-T RTR
Parts Listing
Teileliste
Liste des pièces
Elenco componenti
Part # English Deutsch Français Italiano
LOSA9168 Throttle/Brake Link Set: 8B 2.0 Drossel/Bremskupplung Set: 8B 2.0 8B 2.0 - Biellettes gaz/frein Set collegamenti motore/freno: 8B 2.0
LOSA92203 Hinge Pin Brace Set: 8 RTR Querlenkerhalter: 8 RTR 8 RTR - Jeu cales de pincement Guida perno cerniera: 8 RTR
LOSA9315 Fuel Tubing (24") Kraftstoffleitung (60,9cm, 24Zoll) Durite (24") Tubo miscela (24")
LOSA17701B 1/8 XTT Truggy Tire, Bl, Mntd, w/White Wheel,
0 Offset (2)
1/8 XTT Truggy Reifen verklebt weiße Felge 0
Offset blaue Mischung
Pneus 1/8 XTT truggy noirs, montés avec jantes
blanches, 0 0ffset (2)
Pneumatico truggy 1/8 XTT nero, premontato con
ruota bianca, offset 0 (2)
LOSA99040 Metal Servo Arm Insert, 23S Spline, Airtronics (2) Metall Servo-Armeinsatz, 23S Kerbverzahnung,
Airtronics (2)
Insert 23s Airtronics pour bras de servo métal (2) Inserti metallici squadretta servo, 23 scanalature,
Airtronics (2)
LOSB2831 Rear Shock Shafts (2): 8RTR Dämpferkolbenstange, hinten (2): 8RTR 8 RTR - Tiges d’amortisseurs arr. (Pr) Steli ammortizzatori posteriori (2): 8RTR
LOSB2832 Rear Shock Shafts: 8T 2.0 RTR Dämpferkolbenstange, hinten: 8T 2.0 RTR 8T 2.0 RTR - Tiges d'amortisseurs arr. Steli ammortizzatori posteriori: 8T 2.0 RTR
LOSB4106 Hinge Pin Set: 8 RTR Hinge Pins: 8 RTR 8 RTR - Axes de suspension en Titane Perni cerniera: 8 RTR
LOSB5004 Fuel Tank Lid Pull: 8T 2.0 RTR Kraftstofftankklappenzug: 8T 2.0 RTR 8T 2.0 RTR - Ouverture rapide de réservoir Coperchio a molla per serbatoio: 8T 2.0 RTR
SPMS605 9KG Servo, WP, Metal 23T 9KG WP-Metall-Servo 23T Servo 9kg à pignons métal, étanche, 23T Servo 9 KG, WP, metallo 23T
SPMSR310 SR310 DSMR 3 Ch Sport Receiver SR310 3-Kanal DSMR-Sportempfänger Récepteur SR310 3 voies DSMR Ricevente sport SR310 DSMR 3 canali
SPMSS6100 S6100 High Voltage Surface Servo - Torque S6100 HV Servo, Torque Servo surface S6100 haute tension - Couple Servo superficie S6100 alto voltaggio - torque
TLR234008 Front/Rear Hinge Pin Brace: 22/2.0/T/SCT Front/Heck Scharnierbolzenstrebe: 22/2.0/T/SCT 22/2.0/T/SCT - Renfort de cellule av/arr Set piastrine anteriori/posteriori: 22/2.0/T/SCT
TLR340008 Cab Forward Body, Clear: 8IGHT 4.0 Kabine, vordere Karosserie, klar: 8IGHT 4.0 8IGHT 4.0 - Carrosserie “Cab Forward”,transparente Carrozzeria Cab-Forward, trasparente: 8IGHT 4.0
TLR240009 Body Set, Clear: 8T 3.0 & 4.0 Karosserie Set, Klar: 8T 3.0 & 4.0 8T 3.0 & 4.0 - Carrosserie Set carrozzeria, trasparente: 8T 3.0 & 4.0
TLR242001 Front Center Dogbone: 8IGHT Buggy 3.0 Front/Mittel-Dogbone: 8IGHT Buggy 3.0 8B 3.0 - Cardan central avant Cardano centrale anteriore: 8IGHT Buggy 3.0
TLR242002 Center Dogbone: 8B 3.0 (rear), 8E 3.0 (front) Mittel-Dogbone: 8B 3.0 (Heck), 8E 3.0 (Front) 8B 3.0 (arrière), 8E 3.0 (avant) - Cardan central Cardano centrale: 8B 3.0 (posteriore), 8E 3.0 (anteriore)
TLR242003 Coupler Outdrive: 8IGHT Buggy 3.0 Kupplungsoutdrive 8IGHT Buggy 3.0 8B 3.0 - Noix d’accouplement de cardan Accoppiatore trascinatore: 8IGHT Buggy 3.0
TLR242013 Front and Rear Gear Box Set: ALL 8IGHT Front und Heck GetriebeboxSet: ALL 8IGHT 8IGHT - Set de cellules av et arr Set cellula posteriore e anteriore: ALL 8IGHT
TLR244000 Front Suspension Arm Set: 8IGHT Buggy 3.0 Vorderradaufhängungsarm Set: 8IGHT Buggy 3.0 8B 3.0 - Set de bras de suspension avant Set braccetti sospensioni anteriori: 8IGHT Buggy 3.0
TLR244001 Front Suspension Arm Bushing (4):8IGHT Buggy 3.0 Vorderradaufhängungsbuchse Set (4): 8IGHT Buggy 3.0 8B 3.0 - Set de paliers de bras de suspension avant Set boccole sospensioni anteriori (4): 8IGHT Buggy 3.0
TLR244003 Front Spindle Set: 8IGHT Buggy 3.0 Hauptspindel Set: 8IGHT Buggy 3.0 8B 3.0 - Set de fusées avant Fusello anteriore: 8IGHT Buggy 3.0
TLR244004 Front Spindle Carrier, 15 Degree: 8IGHT Buggy 3.0 Hauptspindelträger, 15 Grad: 8IGHT Buggy 3.0 8B 3.0 - Étrier porte fusée avant, 15° Portafusello anteriore, 15 gradi: 8IGHT Buggy 3.0
TLR244005 Steering Rack Set w/Bearings, Short/Long: 8B 3.0 Zahnstange Set mit Lagern, Kurz/Lang: 8B 3.0 8B 3.0 - Renvois de direction, courts/longs avec
roulements
Cremagliera sterzo con cuscinetti, corta/lunga: 8B 3.0
TLR244007 Hinge Pins, 4 x 21mm,TiCn (2): 8IGHT Buggy 3.0 Scharnierstifte, 4 x 21 mm,TiCn (2): 8IGHT Buggy 3.0 8B 3.0 - Axes en titane 4 x 21mm (2) Perni braccetti, 4 x 21 mm, TiCn (2): 8IGHT Buggy
TLR244008 Rear Suspension Arm Set: 8IGHT Buggy 3.0 Hinterradaufhängungsarm Set: 8IGHT Buggy 3.0 8B 3.0 - Set de bras de suspension arrière Set braccetti sospensioni posteriori: 8IGHT Buggy 3.0
TLR244011 Hinge Pins, 4 x 66mm,TiCn (2): 8IGHT Buggy 3.0 Scharnierstifte, 4 x 66 mm, TiCn (2): 8IGHT Buggy 3.0 8B 3.0 - Axes de suspension en titane 4 x 66mm (2) Perni braccetti, 4 x 66 mm, TiCn (2): 8IGHT Buggy
TLR244012 Outer Hinge Pins, 3.5mm (2): 8IGHT Buggy 3.0 Außenscharnierstifte, 3,5 mm (2): 8IGHT Buggy 3.0 8B 3.0 - Axes de suspension extérieurs, 3,5mm (2) Perni braccetti esterni, 3,5 mm (2): 8IGHT Buggy 3.0
TLR244017 Front Suspension Arm Set: 8T 3.0/2.0 Querlenkersatz vorne: 8T 3.0/2.0 8T 2.0/3.0 - Triangles de suspension avant Set bracci sosp. anter.: 8T 3.0/2.0
TLR244018 Rear Suspension Arm Set: 8T 3.0/2.0 Querlenkersatz hinten: 8T 3.0 8T 2.0/3.0 - Triangles de suspension arrière Set bracci sosp. poster.: 8T 3.0/2.0
TLR244019 Front Shock Tower, Alum: 8T 3.0 Dämpferbrücke vorne Aluminium: 8T 3.0 8T 3.0 - Support d’amortisseurs avant en alu Torre ammort. anter., allum.: 8T 3.0
TLR245000 Droop Screw (4): 8B 3.0 Einsenkschraube (4): 8B 3.0 8B 3.0 - Vis de butée de suspension (4) Viti del droop (4): 8B 3.0
TLR342002 Rear Dogbone & Axle Set: 8IGHT Buggy 3.0 Heck-Dogbone & Achse Set: 8IGHT Buggy 3.0 8B 3.0 - Cardans et axes arrières (2) Set cardano e giunto posteriore: 8IGHT Buggy 3.0
TLR44000 1/8 Buggy Dish Wheel,Yellow (4): 8IGHT Buggy 3.0 1/8 Buggy Tellerscheibe, Gelb (4): 8IGHT Buggy 3.0 8B 3.0 - Jantes pleines Buggy, jaunes (4) Cerchione 1/8 Buggy, giallo (4): 8IGHT Buggy 3.0
TLR4401 Radio Tray, Gen III: 8B/T Radioplatte, Gen III: 8B/T 8B/8T Gen III - Platine radio Piastra radio, Gen III: 8B/T
TLR4403 J Nut, Gen III Radio Tray (2): 8B/T J Mutter, Gen III Radioplatte (2): 8B/T 8B/8T Gen III - Fixations J pour platine radio (2) Dado a J, piastra radio Gen III (2): 8B/T
TLR4406 Throttle Tri-Horn, Gen III Radio Tray: 8B/T Drossel Tri-Horn, Gen III Radioplatte: 8B/T 8B/T - Palonnier de gaz triple, Platine radio Gen III Squadretta motore a 3 bracci, piastra radio Gen III:8B/T
TLR6019 Ballstud/Hub Spacer Set, Aluminum: 22 Kugelbolzen/Abstandsstück, Aluminium: 22 22 - Rotules à visser et entretoises Rondelle hub, alluminio: 22
TLR8200 Body Washer: 8IGHT 2.0 Karosserieunterlegscheibe: 8IGHT 2.0 8IGHT 2.0 - Rondelles de carrosserie Rondella carrozzeria: 8IGHT 2.0
TLR8202 Body Clips, Black (12): 22 TLR Bodyclips, schwarz (12): 22 22 - Clips à carrosserie, noir (12) Clips carrozzeria, nero (12): 22
Part # English Deutsch Français Italiano
DYN1419 7.4V 20000mAh 2S 5C LiPo Receiver Pack: 1/8 Dynamite 2S 7,4V 2000mAh 5C LiPo-Empfängerakku:
1/8
Batterie Li-Po réception 2S 7.4V 20 000mA 5C
pour 1/8
Pacco batteria LiPo per ricevente 5C 7,4 V 2S
20000 mAh: 1/8
DYN2000 Turbo Fueler Bottle, 500cc Dynamite Schnelltankflasche 50ccm Pipette de remplissage Turbo, 500cc Confezione Turbo Fueler, 500 cc
DYN2517 Body Scissors: Curved/Straight Dynamite Lexanschere halb gebogen Ciseaux à lexan : courbé/droit Forbici per carrozzeria: curve/diritte
DYN9905 Dynamite Surface Pit Mat Dynamite Arbeitsunterlage Tapis de stand Dynamite Tappetino per manutenzione Dynamite
DYNT2000 Machined Nut Driver Set (4 pc) US Steckschlüsselset 4 Stück Zoll Set de Tournevis usinés p/écrous 6 pans US (4 pc) Set chiave dadi fresata (4 pc) US
DYNT2020 Machined Hex Driver Set (4) US Alu Inbusschlüssel US 4 Stück Set de Tournevis usinés Hexag (4) US Set chiave esagonale fresata
DYNT2113 Suspension Arm Reamer 4mm Reibaale für Querlenker 4mm Alésoir de triangle de suspension 4mm Alesatore bracci sospensione 4mm
DYNH1020 Stainless Steel Screw Set: TLR 8ight 3.0 buggy Edelstahlschraube Set:TLR 8ight 3.0 buggy TLR 8ight 3.0 - Kit de visserie acier inox Set viti in acciaio inox:TLR 8ight 3.0 buggy
LOSA1754 Adjustable Front Hinge Pin Brace w/Inserts: 8B/8T Einstellbare Front-Scharnierbolzenstrebe mit Einsätzen:
8B/8T
8B/8T - Support d’axes avant réglable avec
mousses
Set piastrine regolabili anteriori con inserti: 8B/8T
LOSA1755 Adjustable Rear Hinge Pin Brace w/Inserts: 8B/8T Einstellbare Heck-Scharnierbolzenstrebe mit Einsätzen:
8B/8T
8B/8T - Support d’axes arr. réglable avec mousses Set piastrine regolabili posteriori con inserti: 8B/8T
LOSA1756 Adjustable Hinge Pin Brace Inserts: 8B/8T Einsätze für einstellbare Scharnierbolzenstrebe: 8B/8T 8B/8T - Inserts mousse support réglable d’axes Set inserti per piastrine regolabili: 8B/8T
LOSA1759 LRC Adj Rear Hinge Pin Brace w/Inserts: 8B/T 2.0 LRC Einstellbare Heck-Scharnierbolzenstrebe mit
Einsätzen: 8B/T 2.0
8B/T 2.0 - Cales de pincement ajustables avec
inserts
Set piastrine regolabili posteriori LRC con inserti:
8B/T 2.0
LOSA3532 Wheel Hexes (4) + 2mm Wider: 8B, 8T Rad-Sechskantstücke (4) + 2 mm weiter: 8B,8T 8B, 8T - Hexagone de jantes (4) +2mm Esagoni ruote (4) 2 mm pi˘ larghi: 8B, 8T
LOSA3533 Wheel Hexes (4) + 1/2" Wider: 8B, 8T Rad-Sechskantstücke (4) + 12,7 mm (1/2 Zoll) weiter:
8B, 8T
8B, 8T - Hexagone de jantes (4) +1/2" Esagoni ruote (4) 1/2" pi˘ larghi: 8B, 8T
LOSA3554 Center HD Lightened Outdrive Set (2) Antriebsklauen für Mitteldiff, Leichtbau (2) Noix de cardans allégées HD (2) Set trascinatore alleggerito centrale HD (2)
Optional Parts
Optionale Bauteile
Pièces optionnelles
Pezzi opzionali

LOSI 8IGHT/8IGHT-T RTR
50
Optional Parts
Optionale Bauteile
Pièces optionnelles
Pezzi opzionali
Part # English Deutsch Français Italiano
LOSA3587 Front Center Universal Driveshaft: 8 2.0 Vordere/Mittlere Universalantriebswelle: 8 2.0 8 2.0 - Cardan central avant Albero di trasmissione centrale anteriore universale:
8 2.0
LOSA3600 Front SmartDiff: 8B 2.0 Front SmartDiff: 8B 2.0 8B 2.0 - SmartDiff avant Diff. Smart anteriore: 8B 2.0
LOSA3601 Center SmartDiff: 8B 2.0 Mittleres SmartDiff: 8B 2.0 8B 2.0 - SmartDiff central Diff. Smart centrale: 8B 2.0
LOSA4416 Aluminum Front Chassis Brace: 8B, 8T Front-Chassis-Strebe (Aluminium): 8B, 8T 8B, 8T - Entretoise de châssis av. alu Trapezio anteriore in alluminio: 8B, 8T
LOSA4417 Aluminum Rear Chassis Brace: 8B, 8T Heck-Chassis-Strebe (Aluminium): 8B, 8T 8B, 8T - Entretoise de châssis arr. alu Trapezio posteriore in alluminio: 8B, 8T
LOSA4440 Front Top Brace, Aluminum: 8B, 8T Obere Frontstrebe, Aluminium: 8B, 8T 8B, 8T - Entretoise supérieure av., alu Montante superiore anteriore in allumnio: 8B, 8T
LOSA4444 Split Center Diff Mount, Aluminum: 8B/8T 2.0 Geteilte Center Diff.-Halterung,Aluminium: 8B/8T 2.0 8B/8T 2.0 - Palier de diff. cent., alu Supporto diff. centrale scomponibile in alluminio:
8B/8T 2.0
LOSA4454 Rear Gearbox Bearing Inserts, Aluminum 8B/8T
2.0
Einsätze f. Heck-Getriebeboxlager, Aluminium 8B/8T 2.0 8B/8T 2.0 - Bague de roulement de diff. arr., alu Inserti cuscinetti ingranaggio posteriore in alluminio
8B/8T 2.0
LOSA5452 15mm Springs 2.3" x 4.7 Rate, Green: 8B 15mm Federn 2,3 x 4,7 Rate, Grün: 8B 8B - Ressorts 15mm dureté 2,3 x 4,7, vert Molle 2,3" 15 mm x rigidezza 4,7, verde: 8B
LOSA5457 15mm Springs 3.1" x 2.8 Rate, Silver: 8B 15mm Federn 3,1" x 2,8 Rate, Siber: 8B 8B - Ressorts 15mm dureté 3,1" x 2,8, argent Molle 3,1" 15 mm x rigidezza 2,8, argento: 8B
LOSA5277 Silicone Diff Fluid, 1000CS TLR Silikon Diff Öl, 1.000CS Graisse silicone pour différentiel, 1000CS Fluido silicone diff, 1000CS
LOSA6140 8IGHT Screw/Nut Assortment Box 8IGHT Schrauben und Muttern im Sortimentskasten 8B - Boite d’assortiment de vis et d’écrous 8IGHT Scatola assortimento viti/dadi
LOSA6540 Turnbuckles 5mmx60mm w/Ends: 8B Spannschrauben 5 mm x 60 mm mit Endstücken:8B 8B - Biellettes 5mm x 60mm avec rotules Tiranti filettati 5 mm x 60 mm con terminali: 8B
LOSA6541 Turnbuckles 5mmx68mm w/Ends: 8B Spannschrauben 5 mm x 68 mm mit Endstücken:8B 8B - Biellettes 5mm x 68mm avec rotules Tiranti filettati 5 mm x 68 mm con terminali: 8B
LOSA6542 Turnbuckles 4mmx60mm w/Ends: 8B Spannschrauben 4 mm x 60 mm mit Endstücken:8B 8B - Biellettes 4mm x 60mm avec rotules Tiranti filettati 4 mm x 60 mm con terminali: 8B
LOSA8131 8IGHT Wing, White: 8B,8T 8IGHT Flügel, Weiß: 8B,8T 8B, 8T - Aileron 8IGH, blanc Alettone 8IGHT, bianco: 8B,8T
LOSA8132 1/8 Universal Wing Kit,Yellow Losi: 1/8 Universal Spoiler, Gelb Aileron 1/8 universel, jaune 1/8 Kit alettone universale, bianco
LOSA9100 8IGHT/T Clutch Rebuild/Service Box 8IGHT/T Kupplungsüberholungs-/Wartungskasten 8IGHT/T - Kit entretien/réparation embrayage Box manutenzione/ricostruzione frizione 8IGHT/T
LOSA9102 Flywheel & Collet, Steel, 4 Shoe: 8B, 8T Schwungscheibe & Zwinge, Stahl, 4 Backen: 8B, 8T 8B, 8T - Volant d’embrayage, acier, 4 Volano e pinza in acciaio, 4 ceppi: 8B, 8T
LOSA9108 Clutch Shoes, Lightened Aluminum (2): 8B, 8T Kupplungsbacken, Extraleichtes Aluminium (2): 8B, 8T 8B, 8T - Cloche masselottes, allégé alu (2) Ceppi frizione, alluminio alleggerito (2): 8B, 8T
LOSA9109 Long-Wear Aluminum Clutch Shoes (4): 8B, 8T Losi Alu Langzeit Kupplungsschuhe (4): 8B, 8T 8B, 8T - Masselottes d’embrayage renforcées
aluminium (4)
Ceppi frizione alluminio lunga durata (4): 8B, 8T
LOSA9126 High Endurance Clutch Bell, 13T: 2.0 Losi 8 2.0: High Endurance Kupplungsglocke 13T 8B 2.0 - Cloche d’embrayage renforcée 13T Campana frizione alta resistenza, 13T: 2.0
LOSA9127 High Endurance Clutch Bell, 14T: 2.0 Losi 8 2.0: High Endurance Kupplungsglocke 14T 8B 2.0 - Cloche d’embrayage renforcée 14T Campana frizione alta resistenza, 14T: 2.0
LOSA9155 Quick Change Engine Mount Set: 8B, 8T Motoraufhängung Schnellwechsel-Set: 8B, 8T 8B, 8T - Quick Change support moteur Set supporto motore per cambio rapido: 8B, 8T
LOSA9156 Quick Change Engine Mount Only: 8B, 8T Nur Schnellwechsel-Motoraufhängung: 8B, 8T 8B, 8T - Quick Change support moteur seul Solo supporto motore per cambio rapido: 8B, 8T
LOSA9314 Ultra Fuel Tubing, 5' Ultra-Kraftstoffleitung, 1,5 m (5 Fuß) Ultra Fuel Tubing, 5' Tubo miscela ultra, 5'
LOSA99030 Servo Arm, Aluminum: JR Servoarm, Aluminium: JR JR - Palonnier de servo, alu Squadretta servo, alluminio: JR
LOSA99031 Servo Arm, Aluminum: KO/AIR/SPM Servoarm, Aluminium: KO/AIR/SPM KO/AIR - Palonnier de servo, alu Squadretta servo, alluminio: KO/AIR/SPM
LOSA99032 Servo Arm, Aluminum: FUT Servoarm, Aluminium: FUT FUT - Palonnier de servo, alu Squadretta servo, alluminio: FUT
LOSA99033 Servo Arm, Aluminum: Hitec Servoarm, Aluminium: Hitec Hitec - Palonnier de servo, alu Squadretta servo, alluminio: Hitec
LOSA99070 Speed-Shot Fuel Gun Losi: Speed-Shot Fuel Gun Pistolet de remplissage rapide Pistola riempimento rapido carburante
LOSA99130 8-in-1 Locking Hex Wrench Kit Losi 8-in-1 Wechseltool Kit de clés hexagonales 8 en 1 Kit chiavi esagonali 8-in-1
LOSA99166 Losi Exhaust Spring Tool Krümmerfeder Werkzeug Outil Losi de ressort d’échappement Chiave tiramolle Losi
LOSA99172 Camber Gauge Losi Sturzlehre Jauge de carrossage Misuratore camber
LOSA99173 Ride Height Gauge Losi Höhenmesser Cale de garde au sol Misuratore altezza da terra
LOSA99174 Car Stand: 8B, 8T 8B, 8T: Fahrzeugständer 8B, 8T - Support de stand Supporto auto: 8B, 8T
LOSA99176 Precision Tire Balancer with Balancing Clay Losi Präzisionsreifenwuchtgerät Equilibreur de pneus 1/8 avec de la pate Bilanciatore gomme di precisione con pongo
LOSB4106 Hinge Pin Set: 8RTR 8RTR: Hinge Pin Set 8RTR:Axes de suspension en Titane Perni cerniera: 8RTR
LOSA99041 Metal Servo Arm Insert, 23 Spline, JR (2) Losi Metall Servohorneinsatz/ 23 Spline/ JR (2) Insert 23s JR en métal pour bras de servo (2) Inserto metallico squadretta servo, 23 scanalature, JR (2)
LOSA99042 Metal Servo Arm Insert, 24 Spline, Hitec (2) Losi Metall Servohorneinsatz/ 24 Spline/ Hitec (2) Insert 24s Hitec en métal pour bras de servo (2) Inserto metallico squadretta servo, 24 scanalature,
Hitec (2)
LOSA99043 Metal Servo Arm Insert, 25 Spline, Futaba (2) Losi Metall Servohorneinsatz/ 25 Spline/ Futaba (2) Insert 25s Futaba en métal pour bras de servo (2) Metal Servo Arm Insert, 25 Spline, Futaba (2)
LOSB4604 17mm Wheel Wrench: LST2, MUG, 8B, 8T LST2, MUG, 8B, 8T: 17mm Radschlüssel Alu LST2, MUG, 8B, 8T: Clé de roue 17mm 17mm chiave ruote: LST2, MUG, 8B, 8T
LOSB5007 Fuel Tank Lid Pull, : 8T 2.0 RTR Tankaufzieher: 8T 2.0 RTR 8T 2.0 RTR - Ouverture rapide de réservoir Coperchio a molla per serbatoio: 8T 2.0 RTR
LOSB5012 Fuel Tank Lid Pull, Fluorescent Yellow: 8T 2.0 Tankaufzieher/Fluor Gelb: 8T 2.0 8T 2.0 - Ouverture rapide de réservoir jaune Serbatoio con tappo a molla, giallo fluorescente:
8T 2.0
LOSF0430 Nitrotane Race 30%, Quart Nitro Kraftstoff für Rennmotor 30% Carburant Nitrométhane à 30%, Quart Miscela da gara Nitrotane 30%, Quart
SPM6400 DX6R 6-Channel DSMR Smart Radio System WiFi/BT Spektrum DX6R 6-Kanal Surface-Sender m. BLE-
Connectivity
Emetteur 6 voies DX6R DSMR avec connexion
WiFi/Bluetooth
Sistema radio Smart DX6R DSMR 6 canali WiFi/BT
TLR3500 F/R CV Driveshaft Axles (4):Aluminum 8B, 8T 2.0 F/H Gleichlaufgelenkwellen (4): Aluminium 8B, 8T 2.0 8B, 8T 2.0 - Axes de roue de cardan CVD av/
arr, Alu (4)
Assi trasmissione ant./post.CV (4): alluminio 8B, 8T
2.0
TLR3501 Differential Shaft Set, Aluminum (6): 8B, 8T 2.0 Diff. Achskreuz, Aluminium (6): 8B, 8T 2.0 8B, 8T 2.0 – Axe de maintien de satellites de
diff., aluminium (6)
Albero differenziale, alluminio (6): 8B, 8T 2.0
TLR3538 Covered 17mm Wheel Nuts,Alum: 8B/8T 2.0 Verkleidete 17 mm Radmuttern,Alum.: 8B/8T 2.0 8B/8T 2.0 - Écrou de roue fermé 17mm en
aluminium
Dadi ruote 17 mm coperti in alluminio: 8B/8T 2.0
TLR5276 8IGHT/T Diff Fluid Refill Kit, 2K,5K,7K Silicone 8IGHT/T Diff.-Flüssigkeit-Nachfüll-Kit, 2K, 5K, 7K Silikon 8IGHT/T - Kit de remplissage des diff., silicone 2K,
5K et 7K
Kit ricarica olio al silicone per differenziale 8IGHT/T,
2K,5K,7K
TLR5277 Silicone Diff Fluid, 1000CS Silikon Diff.-Flüssigkeit, 1000CS Graisse silicone de diff., 1000CS Olio al silicone per differenziale, 1000CS
TLR5278 Silicone Diff Fluid, 2000CS Silikon Diff.-Flüssigkeit, 2000CS Graisse silicone de diff., 2000CS Olio al silicone per differenziale, 2000CS
TLR5279 Silicone Diff Fluid, 3000CS Silikon Diff.-Flüssigkeit, 3000CS Graisse silicone de diff., 3000CS Olio al silicone per differenziale, 3000CS
TLR5280 Silicone Diff Fluid, 5000CS Silikon Diff.-Flüssigkeit, 5000CS Graisse silicone de diff., 5000CS Olio al silicone per differenziale, 5000CS
TLR5281 Silicone Diff Fluid, 7000CS Silikon Diff.-Flüssigkeit, 7000CS Graisse silicone de diff., 7000CS Olio al silicone per differenziale, 7000CS
TLR5282 Silicone Diff Fluid, 10,000CS Silikon Diff.-Flüssigkeit, 10.000CS Graisse silicone de diff, 10 000 CS Olio al silicone per differenziale 10.000CS
TLR5283 Silicone Diff Fluid, 15,000CS Silikon Diff.-Flüssigkeit, 15.000CS Graisse silicone de diff., 15 000 CS Olio al silicone per differenziale, 15.000CS
TLR5284 Silicone Diff Fluid, 20,000CS Silikon Diff.-Flüssigkeit, 20.000CS Graisse silicone de diff., 20 000 CS Olio al silicone per differenziale, 20.000CS
TLR5285 Silicone Diff Fluid, 30,000CS Silikon Diff.-Flüssigkeit, 30.000CS Graisse silicone de diff., 30 000 CS Olio al silicone per differenziale, 30.000CS
TLR5286 Silicone Diff Fluid, 50,000CS Silikon Diff.-Flüssigkeit, 50.000CS Graisse silicone de diff., 50 000 CS Olio al silicone per differenziale, 50.000CS
TLR5288 Silicone Diff Fluid, 125,000CS Silikon Diff.-Flüssigkeit, 125.000CS Graisse silicone de diff., 125 000 CS Olio al silicone per differenziale, 125.000CS
TLR6019 Ballstud/Hub Spacer Set, Aluminum: 22 Distanzringe für Kugelkopf, Aluminium: 22 22 – Rondelles d’espacement, aluminium Rondelle hub, alluminio: 22
TLR240000 Body Set, Clear: 8 3.0 Karosserie Set, Klar: 8 3.0 8B 3.0 - Carrosserie Set carrozzeria, trasparente: 8 3.0
TLR240001 Wing, Black 8IGHT Buggy 3.0 Flügel, Black 8IGHT Buggy 3.0 8IGHT Buggy 3.0 - Aileron noir Alettone, nero 8IGHT Buggy 3.0