1
2
3
4
5
6
Pin Cable
color 1* Cable
color 2* Pin/wire function denition
Use Regulations
Magnetostrictive displacement sensor is used to detect the displacement of motion mechanism. According to
the selection regulations, the magnets matched with magnetostrictive displacement detection electronic compo-
nents are selected for detection applications in different occasions. During use, ensure that the cable,connector,
magnet and sensor body are the original parts of the manufacturer.
Please do not open the shell of the sensor without authorization, so as not to affect the normal warranty period
of the product.
Saftey matters
Please read the manual carefully before powering up the sensor. First, conrm the outlet mode and pin signal
of the sensor, and make correct electrical connection to prevent power-on from damaging the sensor or causing
misoperation of the equipment.During the construction and use of the sensor, the current of high-power equipment
such as welding machine should be avoided from entering the working circuit of the sensor.
If you nd that the sensor data is abnormal or the appearance has obvious changes, please stop using it
immediately, and contact the manufacturer to conrm the current state of the sensor before continuing to use it.
Status indication/fault analysis
Installation Dimensions
Electric interface
Outgoing mode: Cable outlet
RH
RP
RF
Outgoing mode: Connector
Application environment
Magnetostrictive displacement sensor is a kind of magnetic measurement sensor. Make sure there is no
strong magnetic eld around the sensor, which may interfere with the data.
The displacement output signal cable of magnetostrictive displacement sensor should be away from the
power cable or large current or strong pulse interference source.
Conrm the environmental parameters including temperature, vibration, etc., and ensure that the working
conditions are within the nominal working parameters of the sensor.
Installation
The installation of magnetostrictive displacement sensor mainly includes sensor body, magnet and cable
xing.
The installing forms of the sensor body are: thread installing, clamp installing and matching xing installing.
Before installation, make sure that the packaging is in good condition, and the sensor body has no obvious
bending and bumping. The sensor body should be assembled according to the specic installation form.
When installing magnets, please use matching magnetic insulation gaskets to ensure normal magnetic eld
circuit.
When installing plugs or cables, please connect them accurately according to the electrical interfaces in the
instructions.
After-sales support
If the sensor malfunctions, please contact the after-sales department of the company in time. Do not attempt
to repair it yourself.
flexible zone (bending radius
should not less than 250mm)
Hard outer
tube at the end
End non-usable area
Stroke length
Head non-usable area
O-ring
94
61
Hard outer tube
at head end
93 40
Ф9.1
Ф7.9
62/72(DP/PN)
Ф7.9
Stroke length 63.5/10750.810
24
Hexagonal flat flange
M18×1.5
Opposite side 46mm
Outer diameter Ф12
Outer diameter Ф12.7
Standard
magnet ring
Total length
<7620mm，deviation0~+8mm；>7620mm，deviation-5~+15mm。
（Total length deviation has no effect on Stroke length）
*
*
1
2
3
4
5
6
7
8
Pin Cable
color 3* Pin/wire function denition
Green light
ON
ON
Flash
Red light
OFF
ON
OFF
Function
Normal work
Magnet not detected
Programming state
The sensor has no
interrogation signal
ON Flash Star/stop
sensor
Start-
Start+
Stop-
Stop+
Controller start signal
Sensor output signal
Stop Time interval Begin
2~5µs
1.5~2µs
1.5~2µs
Con-
troller
Schematic diagram of START-STOP signal
Head dead area
63.5
Ф10
50.87232
24
Stroke length
End dead area
Starting point of sector magnet/
square magnet stroke
45.5
Stroke length End Non-usable area
14.5
9
3812
M5
13
67 28 66
Mounting clamp 36
50
68
M5×16
46
1.8
61
~38
12
46
46
Blue
Green
Yellow
White
Red
Black
Grey
Pink
Yellow
Green
Brown
White
Stop（-）
Stop（+）
Start（+）
Start（-）
0 Vdc
6-pin male connector arrangement (facing the
sensor head)
Note: * Cable color 1: Cable PUR sheath, orange,-20~90℃
* Cable color 2/3: Cable PVC sheath, orange,-20~105℃
Yellow
Grey
Pink
-
Green
Blue
Brown
White
Start（+）
Stop（+）
Start（-）
Reservation
Stop（-）
0 Vdc（power supply circuit）
+24Vdc power supply（-20%~+20%）
Reservation
8-pin male connector arrangement (facing the
sensor head direction)
+24Vdc power supply（-20%~+20%）
