Tech Controllers EU-20 User manual

USER’S MANUAL
EU-20
Safety
Before using the device for the rst time the user should read the
following regulations carefully. Not obeying the rules included in this
manual may lead to personal injuries or controller damage. The user’s
manual should be stored in a safe place for further reference. In order to
avoid accidents and errors it should be ensured that every person using
the device has familiarized themselves with the principle of operation as
well as security functions of the controller. If the device is to be sold or
put in a dierent place, make sure that the user’s manual is there with
the device so that any potential user has access to essential information
about the device.
The manufacturer does not accept responsibility for any injuries or
damage resulting from negligence; therefore, users are obliged to take
the necessary safety measures listed in this manual to protect their lives
and property.
We are committed to protecting the environment. Manufacturing
electronic devices imposes an obligation of providing for environmentally
safe disposal of used electronic components and devices. Hence, we have
been entered into a register kept by the Inspection For Environmental
Protection. The crossed-out bin symbol on a product means that the
product may not be disposed of to household waste containers. Recycling
of wastes helps to protect the environment. The user is obliged to transfer
their used equipment to a collection point where all electric and electronic
components will be recycled.
WARNING
• High voltage! Make sure the regulator is disconnected from the
mains before performing any activities involving the power supply
(plugging cables, installing the device etc.)
• The device should be installed by a qualied electrician.
• Before starting the controller, the user shoud measure earthing
resistance of the electric motors as well as the insulation resistance
of the cables.
• The regulator should not be operated by children.
WARNING
• The device may be damaged if struck by a lightning. Make sure the
plug is disconnected from the power supply during storm.
• Any use other than specied by the manufacturer is forbidden.
• Before and during the heating season, the controller should be
checked for condition of its cables. The user should also check if the
controller is properly mounted and clean it if dusty or dirty.
WARRANTY CARD
TECH company ensures to the Buyer proper operation of the device for the period of 24 months from the date of sale. The
Guarantor undertakes to repair the device free of charge if the defects occurred through the manufacturer’s fault. The device
should be delivered to its manufacturer. Principles of conduct in the case of a complaint are determined by the Act on specic
terms and conditions of consumer sale and amendments of the Civil Code (Journal of Laws of 5 September 2002).
CAUTION! THE TEMPERATURE SENSOR CANNOT BE IMMERSED IN ANY LIQUID (OIL ETC). THIS MAY RESULT IN
DAMAGING THE CONTROLLER AND LOSS OF WARRANTY! THE ACCEPTABLE RELATIVE HUMIDITY OF THE CONTROLLER’S
ENVIRONMENT IS 5÷85% REL.H. WITHOUT THE STEAM CONDENSATION EFFECT.
THE DEVICE IS NOT INTENDED TO BE OPERATED BY CHILDREN.
Activities related to setting and regulation of the controller parameters described in the Instruction Manual and parts wearing
out during normal operation, such as fuses, are not covered by warranty repairs. The warranty does not cover damages arising
as a result of improper operation or through the user’s fault, mechanical damage or damage created as a result of re, ood,
atmospheric discharges, overvoltage or short-circuit. The interference of an unauthorized service, wilful repairs, modications
and construction changes cause the loss of Warranty. TECH controllers have protective seals. Removing a seal results in the
loss of Warranty.
The costs of unjustiable service call to a defect will be borne exclusively by the buyer. The unjustiable service call is dened
as a call to remove damages not resulting from the Guarantor’s fault as well as a call considered unjustiable by the service
after diagnosing the device (e.g. damage of the equipment through the fault of the client or not subject to Warranty), or if the
device defect occurred for reasons lying beyond the device.
In order to execute the rights arising from this Warranty, the user is obliged, at his own cost and risk, deliver the device to
the Guarantor along with a correctly lled-in warranty card (containing in particular the sale date, the seller’s signature and
a description of the defect) and sales proof (receipt, VAT invoice, etc.). The Warranty Card is the only basis for repair free of
charge. The complaint repair time is 14 days.
When the Warranty Card is lost or damaged, the manufacturer does not issue a duplicate.
...................................... ......................................
seller’s stamp date of sale
EN

Principle of operation
The task of the regulator is to switch the pump on when the temperature
exceeds the pre-set value and to switch the pump o when the boiler
cools down (as a result of damping). It prevents unnecessary operation of
the device which, in turn, helps to save electricity (up to 60%, depending
on the boiler use) and prolongs the life of the device. Consequently, the
device is more reliable and the maintenance costs are reduced.
How to use the regulator
The pump activation temperature is set using a potentiometer (within
the range of 25˚C-85˚C). The pump is disabled if the actual temperature
drops by 2˚C below the pre-set value. It prevents regular pump activation
(which aects its durability) due to small temperature uctuation.
Apart from the potentiometer, the regulator is equipped with a power
switch (if the device is switched on, the control light power goes on), a
switch to enable the pump manually (when the pump is enabled, Manual
mode control light goes on) and a control light labelled manual which
signalises the pump operation.
The regulator has a WT 1,6A tube fuse-link protecting the network.
1.Potentiometer
2. Control light indicating manual mode
3. Control light indicating power supply
4. Control light indicating pump operation
5. Power switch
6. Fuse 1,6A
7. Power supply
8. CH pump output
9. Temperature sensor
10.Manual mode switch
How to install the regulator
The sensor should be installed in a proper place with the use of a cable
tie and protected from the inuence of external factors with an insulating
tape. The device power cord should be connected in the following way:
blue (N) and brown (L) - 230V AC/50 Hz, yellow-green (protective)
should be earthed.
TECHNICAL DATA
NO SPECYFIKATION
1. Power supply 230V ±10% /50Hz
2. Maximum power consumption 2W
3. Ambient temperature 5÷50
4. Pump max. output load 0,5A
5. Temperature measurement accuracy 1°C
6. Sensor thermal resistance -30÷99°C
7. Fuse 1,6A
EU Declaration of conformity
Hereby, we declare under our sole responsibility that EU-20 manufactured
by TECH, headquartered in Wieprz Biała Droga 31,
34-122 Wieprz, is compliant with:
• Directive 2014/35/EU of the European Parliament and of the
Council of February 26, 2014 on the harmonisation of the laws of Member
States relating to the making available on the market of electrical
equipment designed for use within certain voltage limits (EU
Journal of Laws L 96, of 29.03.2014, p. 357),
• Directive 2014/30/EU of the European Parliament and of the
Council of February 26, 2014 on the harmonisation of the laws of Member
States relating to electromagnetic compatibility (EU Journal of Laws L 96
of 29.03.2014, p.79),
• Directive 2009/125/EC establishing a framework for the
setting of ecodesign requirements for energy-related products,
• the regulation by the Ministry of Economy of May 8, 2013
concerning the essential requirements as regards the restriction of
the use of certain hazardous substances in electrical and electronic
equipment, implementing provisions of RoHS directive 2011/65/EU.
For compliance assessment, harmonized standards were used:
PN-EN 60730-2-9:2011, PN-EN 60730-1:2016-10
Wieprz, 06.05.2019
23
4
1
5
6
8
9
10