Tech Controllers EU-27i User manual

TECH
1
EU-27i

EU-27i User's manual
2
EU DECLARATION OF CONFORMITY
Hereby, we declare under our sole responsibility that EU-27i manufactured by TECH, head-quartered in
Wieprz Biała Droga 31, 34-122 Wieprz, is compliant with Directive 2014/35/EU of the European Parliament and of
the Council of 26 February 2014 on the harmonisation of the laws of Member States relating to the making available
on the market of electrical equipment designed for use within certain voltage limits (EU OJ L 96, of 29.03.2014, p.
357), Directive 2014/30/EU of the European Parliament and of the Council of 26 February 2014 on the
harmonisation of the laws of Member States relating to electromagnetic compatibility (EU OJ L 96 of 29.03.2014,
p.79), Directive 2009/125/EC establishing a framework for the setting of ecodesign requirements for energy-related
products as well as the regulation by the MINISTRY OF ENTREPRENEURSHIP AND TECHNOLOGY of 24 June 2019
amending the regulation concerning the essential requirements as regards the restriction of the use of certain
hazardous substances in electrical and electronic equipment, implementing provisions of Directive (EU) 2017/2102
of the European Parliament and of the Council of 15 November 2017 amending Directive 2011/65/EU on the
restriction of the use of certain hazardous substances in electrical and electronic equipment (OJ L 305, 21.11.2017,
p. 8).
For compliance assessment, harmonized standards were used:
PN-EN IEC 60730-2-9:2019-06, PN-EN 60730-1:2016-10.
Wieprz, 22.07.2021

TECH
3
I. Safety
Before using the device for the first time the user should read the following regulations carefully. Not
obeying the rules included in this manual may lead to personal injuries or controller damage. The
user’s manual should be stored in a safe place for further reference. In order to avoid accidents and
errors it should be ensured that every person using the device has familiarized themselves with the
principle of operation as well as security functions of the controller. If the device is to be sold or put
in a different place, make sure that the user’s manual is there with the device so that any potential
user has access to essential information about the device.
The manufacturer does not accept responsibility for any injuries or damage resulting from negligence;
therefore, users are obliged to take the necessary safety measures listed in this manual to protect
their lives and property.
WARNING
•High voltage! Make sure the regulator is disconnected from the mains before per-
forming any activities involving the power supply (plugging cables, installing the de-
vice etc.)
•The device should be installed by a qualified electrician.
•Before starting the controller, the user shoud measure earthing resistance of the
electric motors as well as the insulation resistance of the cables.
•The regulator should not be operated by children.
WARNING
•The device may be damaged if struck by a lightning. Make sure the plug is discon-
nected from the power supply during storm.
•Any use other than specified by the manufacturer is forbidden.
•Before and during the heating season, the controller should be checked for condition
of its cables. The user should also check if the controller is properly mounted and clean
it if dusty or dirty.
We are committed to protecting the environment. Manufacturing electronic
devices imposes an obligation of providing for environmentally safe disposal
of used electronic components and devices. Hence, we have been entered
into a register kept by the Inspection For Environmental Protection. The
crossed-out bin symbol on a product means that the product may not be
disposed of to household waste containers. Recycling of wastes helps to
protect the environment. The user is obliged to transfer their used
equipment to a collection point where all electric and electronic components
will be recycled.
!
!

EU-27i User's manual
4
II. Control panel description
III. Working rule
EU-27 regulator is intended to control the operation of CH circulation pump and the operation of
additional pump (HCW or floor pump). The task of the regulator is to switch the CH pump on, if the
temperature exceeds the threshold activation value and to switch the pump off when the boiler cools
down (as a result of extinguishing). For the second pump, apart from activation temperature, the user
adjusts the set temperature to which the pump will operate.
The regulator is equipped with a system preventing from a stoppage of CH and HCW pumps, the so-
called. anti-stop. If the pump works for a longer period (e.g.. beyond the season), then the pump is
turned on every 7 days for 1 minute. Additionally, time is saved every hour in a non - volatile EEPROM
memory, thanks to which, after possible stoppage in supply, time measurement is continued.
The controller has been also equipped with the function of protection against water freezing, the so-
called anti--freezing. After the sensor temperature of the CH HCW pump decreases below 7oC, the
pump is switched on. The pump will work until the moment when the sensor temperature reaches the
value of 9oC.
A user makes every change of parameters by means of pulse generator knob. Turning the knob
allows to mark the requested function or change its value, while pressing the knob causes entering a
given function or a confirmation of change in its value. To exit any function, use exit button.
IV. Controller functions
IV.a) Manual operation
Using this function, a user may start each active executive
device of each regulator manually, independently of the others,
and control alarm work.
CH pump
pump 2
Pulse
generator
knob (entering
MENU, selection
and approval of
settings)
Exit,
cancellation
of settings
Standby mode
(standby)
Current CH,
HCW
temperature
Manual
operation
Temp. HCW
preset
temperatur
e
48oC 40oC 45oC
CH HCW set.HCW

TECH
5
Pressing PULSE GENERATOR switches CH water pump on/off:
Pressing PULSE GENERATOR switches HTW water pump
on/off:
Pressing PULSE GENERATOR switches the alarm on/off :
IV.b) Pump type 2
This setting allows to choose (activate) the proper type of the second pump between HCW and floor
pump. If an additional pump is not connected, No pump option should be chosen.
Depending on the settings, additional functions will be available for the selected pumps and the
appropriate screen view will be visible:
•No pump (CH view)
It is possible to change the activation threshold temperature
directly from the main screen, using plus and minus buttons.
•HCW pump (CH and HCW view)
It is possible to change the preset HCW temperature directly
from the main screen, using plus and minus buttons.
•Floor pump (CH and floor view)
It is possible to change the preset floor temperature directly
from the main screen, using plus and minusbuttons.
IV.c) Working mode
If pump 2 is not selected, the regulator will run
according to CH pump settings (see chapter 3).
In the case of choosing the second pump as HCW, the following working modes will appear:
Manual operation
Pump type 2
CH pump*
HTW pump
CH pump
HTW pump*
HTW pump
Alarm test *
No pump *
HCW pump
48o C, 40o C,
CH act.threshold
HCW pump*
Floor pump
48o C, 40o C, 45o C,
CH HCW HCWpreset
HCW pump
Floor pump *
48oC 40oC 45oC
CH Floor preset.

EU-27i User's manual
6
•CH only
In this mode, only CH pump will work, HCW pump will not be activated.
•Simultaneous pumps
In this mode, both pumps will be active at the same time, each according to their own settings
activation.
•HCW priority
After selecting this mode, HCW pump will be activated first, and after reaching the preset temperature,
HCW pump will be deactivated then, CH circulation pump will be activated. Re-switching to HCW
pump will take place, when the reboiler temperature falls below the preset value by HCW hysteresis
value.
•Lukewarm mode
After activating this function, CH pump is deactivated and HCW pump works according to the preset
activation parameters.
In the case of selecting the second pump as floor pump, the following operating modes will
appear:
•CH only
In this mode, only CH pump will work, floor pump will not be activated.
•Simultaneous pumps
In this mode, both pumps will be active at the same time, each according to their own settings
activation.
•Only floor
After activating this function, CH pump is deactivated and floor pump works according to the preset
activation parameters.
ATTENTION
In the event when there are two circulation pumps active, pump 2 (HCW or floor) is turned off, if their
temperatures become equal. Re-activation will take place when the CH circulation temperature is
greater by at least 2°C.
IV.d) CH pump (settings)
With this function, activation parameters of CH pump should be configured:
•CH pump temperature
This is a threshold activation temperature value, after reaching it, a pump starts working. The pump
will be deactivated when the CH temperature falls below the activation temperature by CH hysteresis
value.
•CH hysteresis
CH pump will be deactivated after the decrease in circulation temperature below the activation
temperature by CH hysteresis.
IV.e) HCW pump (settings)
This setting shall be active, after choosing HCW pump (MENU> pump type 2). Using this
function, activation parameters of HCW pump should be configured:
•HCW activation temperature
This is a threshold activation temperature value, after reaching it, a pump starts working. The pump
will be deactivated when HCW temperature falls below the activation temperature by HCW hysteresis
or reaches the preset temperature.
•Preset HCW
It is a temperature value of a reboiler, after reaching it, HCW is turned off. The pump will be activated

TECH
7
again, when the temperature falls below the preset one by HCW hysteresis value.
•HCW hysteresis
The HCW pump will be deactivated after the decrease in the temperature in circulation below the
activation temperature by HCW hysteresis. In the event when the preset temperature is reached
and the pump is deactivated, pump re-activation will take place, when the temperature falls below the
preset one, by HCW hysteresis.
IV.f) Floor pump (settings)
this setting shall be active, after choosing the floor pump (MENU> pump type 2). Using this function,
parameters switching on the floor pump should be configured:
•Floor pump activation temperature
This is a threshold activation temperature value, after reaching it, a pump starts working. The pump
will be deactivated when floor temperature falls below the activation temperature by floor hysteresis
value or reaches the preset temperature
•Preset floor pump temperature
It is a floor pump temperature value, after reaching it, the floor pump is deactivated. The pump will
be activated again, when the temperature falls below the preset one by floor hysteresis value.
•Floor pump hysteresis (floor hysteresis)
Floor pump will be deactivated after the decrease in temperature in the circulation below the activation
temperature by floor hysteresis value. In the event when the preset temperature is reached and the
pump will be deactivated, pump re-activation will take place, when the temperature falls below the
preset one by floor hysteresis value.
IV.g) Factory settings
By activating the option factory settings, all user's own device settings are replaced the
settings saved by the manufacturer (it does not apply to servicing menu settings). From that moment,
the own controller parameters may be set once again.
V. Servicing menu
In order to enter the servicing mode settings, network switch should be switched to the item O,
then output button should be pressed and, without the interval, network switch should be switched to
the item I. After a few seconds, the regulator enters the servicing mode. In order to return to user
menu (exit servicing menu), the controller should be deactivated and activated again.
1. Alarm temperature
This function applies to securing temperature circulation. It is a critical temperature value, at
which the alert sound occurs along with the respective message on the display.
2. Alarm hysteresis
After the occurrence of an alert temperature, the possibility of switching it off takes place, after
the decrease of temperature below alarm value by alarm hysteresis value.
3.Anti-stop
This setting allows for deactivating/activating anti-stop function.
4.Anti--freezing
This setting allows for deactivating/activating anti--freezing function.

EU-27i User's manual
8
VI. Alarms
Each alarm controller is signaled with the sound, red "Alarm" diode lit on the panel, flashing
screen, and the appropriate message on the screen. Leaving alarm mode proceeds by pressing any
button, after the removal of the defect (or after cooling the circulation).
Below, the operated alarms are shown subsequently, according to priority:
1. No CH sensor
Text on a display:
The activation of CH pump takes place, also HCW pump is
activated, if the 2nd pump is HCW.
2. Shorted CH sensor
Text on a display:
The activation of CH pump takes place, also HCW pump is
activated, if the 2nd pump is HCW.
3. No CHW sensor
Text on a display:
The activation of CH pump takes place. Working mode switched
to "CH only". The second pump type is switched to "No pump".
4. Shorted sensor 2
Text on a display:
The activation of CH pump takes place. Working mode switched
to "CH only". The second pump type is switched to "No pump".
5. CH temperature above the alarm value
Text on a display:
The activation of CH pump takes place, and HCW pump is also
activated, if pump 2 is HCW pump.
6.Temperature 2 above the alarm value
Text on a display:
The activation of CH pump takes place, also HCW pump is
activated, if the 2nd pump is HCW.
7. Temperature 2 below 7°C
Text on a display:
The alarm is active only when anti-freezing option is activated.
The activation of CH pump takes place, and if pump 2 is HCW,
HCW pump is also activated until reaching 9°C.
!NO!
!CH sensor!
!Shorted!
!CH sensor!
!NO!
!Sensor 2!
!Shorted!
!Sensor 2!
!Temperature!
!CH sensor!
!Temperature!
!Sensor 2!
!Below 7⁰C!
!Sensor 2!

TECH
9
8. CH temperature below 7°C
Text on a display:
The alarm is active only when anti-freezing option is activated.
The activation of CH pump takes place, and if pump 2 is HCW,
HCW pump is also activated until reaching 9°C.
9. Test alarm
Text on a display:
VII. Fuse
The regulator is equipped with WT 3.15 A tubular cartridge fuse, protecting the network. Using a
fuse with a higher value may cause damage to the controller.
VIII. Maintenance
In EU-27i Controller, technical condition of wires should be checked before the heating season and
throughout its duration. Fastening of the controller should be also checked, it should be cleaned from
dust and other dirt. Earthing effectiveness of the engines should be also measured.
Technical Data EU-27i
Specification
Unit
Power supply
V
230V +/-10% / 50Hz
Power consumption
W
4
Ambient Temperature
OC
5÷50
CH Pump max. output load
A
0,5
Second Pump max. output load
A
0,5
Measurement Accuracy
OC
1
Sensor Thermal Resistance
OC
-30÷99
Fuse Insert
A
3,15
for
Temperature
Adjustment Range
ON threshold
OFF threshold
hysteresis
From
To
Max
Od
To
Fact.
CH
30 oC
70 oC
40 oC
1
oC
20
oC
2 oC
CHW
20 oC
60 oC
30 oC
55 oC
60 oC
1
oC
20
oC
2 oC
Floor
20 oC
50 oC
30 oC
45 oC
50 oC
1
oC
20
oC
2 oC
ALARM
70 oC
90 oC
85 oC
1
oC
5 oC
2 oC
!Below 7⁰C!
!CH sensor!
!Alarm!

EU-27i User's manual
10
IX. Assembly
Attention: The assembly should be done only by the person with proper qualifications! The
device in this time must not be live (you should ensure that plug is disconnected from the grid)!
ATTENTION: wrong connection of wires can cause the damage of the regulator!
IX.a) The diagram of connecting cables to the
controller.
While assembly of wiring of the controller you should pay special attention to correct connecting
ground wires.
PE - earthing (yellow and green)
N – neutral (blue)
L – phase (brown)