Techly IDATA EXT-465P User manual

P/N: IDATA EXT-465P
8059018366587
EN User's Manual
IT Manuale d’istruzione
WWW.TECHLY.COM
HDMI EXTENDER
4K@60HZ
Technical features
50 M
POINT
TO POINT

HDMI EXTENDER 4K@60HZ
Dear Customer
Thank you for purchasing this product. For optimum performance and safety, please read these instructions
carefully before connecting, operating or adjusting this product. Please keep this manual for future reference.
IMPORTANT SAFETY INSTRUCTION
INTENDED USE
We do not permit using the device in other ways like described in this user’s manual.
Use the product only in dry interior rooms. Not attending to these regulations and
safety instruction might cause fatal accidents, injuries, and damages to persons and
property. The manufacturer/supplier assumes no liability for damages caused by
failure to comply with the intended use.
To reduce risk of electric shock, this product should
ONLY be opened by an authorized technician when
service is required. Disconnect the product from mains
and other equipment if a problem should occur. Do not
expose the product to water or moisture.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
• Your product is not a toy and is not meant for children, because it contains small parts which can be
swallowed and can injure when used inappropriately!
• Please install the system and devices attached to it in a way that persons cannot be injured, or
objects not be damaged for example by dropping or stumbling.
• Please remove the packing materials, because children may cut themselves on them while playing.
Furthermore, there is a risk of swallowing and inhalation of incidentals and insulating material.
• Avoid places with high temperatures, or humidity, or places which might come into contact with
water. Do not install the product close to openings of air conditioners, or at places with an excessive
amount of dust or smoke. Do not place this apparatus near or over a radiator or heat register, or
where it is exposed to direct sunlight. Any liquid that goes into the apparatus may cause a failure,
fire, or electric shock.
• Do not install the product at places subject to vibration, or oscillation.
• Do not modify and alter the product and any accessories! Do not use any damaged parts.
• Keep enough space around all devices for a good ventilation and free motion and to avoid damages.
• Do not mix up HDMI to RJ45 transmitter and RJ45 to HDMI receiver before installation
EN - 2
WWW.TECHLY.COM
HDMI EXTENDER 4K@60HZ

• Do not unplug the device when it is in using, keep distance from flammable and explosive devices.
• Static electricity will cause damage of the device, please do ESD protection when using the device
• To prevent electric shock, please ensure that all apparatus is properly grounded and never insert
anything metallic into the open parts of this apparatus.
• If a three-party power supply is used, please ensure that the power supply specifications meet the
product requirements.
INTRODUCTION
This is an HDMI point-to-point extender kit, it can realize zero-latency transmission. The 4K@60Hz
HDMI signal can be extended by 50m through CAT6/6A/7 network cable. It supports HDMI loop out, IR
passthrough, etc. This kit is a reliable, ultra-high-definition video transmission solution, which is widely
used in security monitoring, home theater, broadcasting, training and other fields.
FEATURES
1. Zero-latency transmission.
2. Extend 4K@60Hz HDMI signal up to 50m over Cat6/6A/7 cable.
3. Support HDR10.
4. Support EDID passthrough and auto downscaling.
5. Support PoC network cable power supply, only TX power supply is needed.
6. The transmitter supports HDMI loop out.
7. Support IR passthrough.
8. Lightning protection, surge protection, ESD protection.
9. Plug and play.
PACKAGE CONTENTS
• Transmitter x1 • Receiver x1 • Power Supply DC5V2A x1 • User manual x1 • IR blaster extension
cable x1 • IR receiver extension cable x1
INSTALLATION REQUIREMENTS
ITEM DESCRIPTION REQUIREMENT
Signal source Devices with HDMI port (PC, DVD, NVR, etc.) HDMI cable ≤5m
Cable CAT6/6A/7, following standard IEEE-568B CAT6/6A/7≤50m
Display device TVs, projectors, etc. with HDMI port HDMI cable ≤5m
EN - 3
WWW.TECHLY.COM
HDMI EXTENDER 4K@60HZ

H D M I O U T
H D M I D i sp la y
N e t w o r k c ab l e
H D M I D i sp la y
TX RX Video So urce
Po C
D C 5 V
①②③⑤ ⑥④
⑦
①②③⑤ ⑥④
IR receiverIR blaster
H D M I O U T
H D M I D i sp la y
N e t w o r k c ab l e
H D M I D i sp la y
TX RX Video So urce
Po C
D C 5 V
①②③⑤ ⑥④
⑦
①②③⑤ ⑥
④
IR receiverIR blaster
PANEL DESCRIPTION
1. Transmitter
Power input Connect with DC 5V power adapter
RJ45 output Connect with CAT6/6A/7 network cable
IR OUT Connect with IR blaster extension cable
Reset Hole Press the pinhole reset button with a straightened paper clip
Power Indicator When there is power, the indicator will light solid blue
HDMI Output Connect with local HDMI display device with HDMI cable
HDMI Input Connect with HDMI source device with HDMI cable
Power input Spare power port (Powered by TX)
RJ45 output Connect with CAT6/6A/7 network cable
IR IN Connect with IR receiver extension cable
Reset Hole Press the pinhole reset button with a straightened paper clip
Power Indicator When there is power, the indicator will light solid blue
HDMI Output Connect with HDMI display device with HDMI cable
2. Receiver
EN - 4
WWW.TECHLY.COM
HDMI EXTENDER 4K@60HZ
7

H D M I O U T
H D M I D i sp la y
N e t w o r k c ab l e
H D M I D i sp la y
TX RX Video So urce
Po C
D C 5 V
①②③⑤ ⑥④
⑦
①②③⑤ ⑥④
IR receiverIR blaster
INSTALLATION PROCEDURES
1. Connection Diagrams
2. Connection Instructions
1) Connect the source device to the HDMI IN port of the transmitter with an HDMI cable, and connect
the HDMI OUT port of the receiver to the display device with another HDMI cable.
2) Use a Cat6/6A/7 cable to connect the RJ45 port of the transmitter and receiver.
3) If using HDMI loop out, connect the display device to the HDMI OUT port of the transmitter.
4) If using IR passthrough, the IR blaster extension cable should plug in the IR OUT port of the
transmitter, the IR receiver extension cable should plug in the IR IN port of the receiver.
5) Plug the power supply into the devices to get started.
EN - 5
WWW.TECHLY.COM
HDMI EXTENDER 4K@60HZ

H D M I O U T
H D M I D i sp la y
N e t w o r k c ab l e
H D M I D i sp la y
TX RX Video So urce
Po C
D C 5 V
①②③⑤ ⑥④
⑦
①②③⑤ ⑥④
IR receiverIR blaster
3. IR User Guide
1. Power
2. IR Signal
3. Null
1. Power
2. IR Signal
3. Grounding
1) IR blaster extension cable should plug in the IR OUT port of the transmitter, IR receiver extension
cable should plug in the IR IN port of the receiver.
2) The emitter of the IR blaster extension cable should be as close as possible to the IR receiving
window of the source device.
3) Point the remote control at the receiving head of the IR receiver extension cable to operate.
FAQ
Q: The devices are connected correctly, but why is there no image displayed?
A: 1) Please make sure the HDMI cable meets the transmission requirements. (e.g. 4K HDMI cable)
2) Please check and make sure the network cable is connected well.
3) Restart the transmitter or receiver by pressing the reset button.
Q: Why does the display occasionally have a black screen?
A: 1) Check if the length of the cable is within the specified range.
2) Reset the transmitter or receiver to re-built the connection.
Q: Why is the display color abnormal or no sound?
A: 1) Reset the transmitter or receiver to re-built the connection.
2) Check if the HDMI cables are connected well.
3) Reconnect the network cable.
EN - 6
WWW.TECHLY.COM
HDMI EXTENDER 4K@60HZ

TECHNICAL PARAMETERS
ITEMS TRANSMITTER RECEIVER
VIDEO
Input Interface
1x HDMI Type A Female 1x RJ45 Female
Output Interface 1x HDMI Type A Female; 1x RJ45 Female 1x HDMI Type A Female
HDMI Length ≤ 5m ≤ 5m
Maximum transfer rate 18Gbps
Maximum transmission
bandwidth
600MHz
EDID passthrough Yes
Compatibility
HDMI 2.0 (Deep color, 4K, HDR, YUV4:4:4)
HDCP 2.2, HDCP1.4
Resolutions
480i@60Hz, 480p@60Hz, 576i@50Hz, 576p@50Hz, 720p@50/60Hz,
1080i@50/60Hz,1080p@50/60Hz, 3840x2160@24/25/30/50/60Hz,
3440x1440, 2560x1440, 2560x1080, 2048x1080, 1920x1440, 1920x1080,
1280x960, 1280x800, 1280x768, 1680x1050, 1360x768, 1366x768,
1600x900,1024x768, 800x600
Transmission distance 4K transmission distance 50m; 1080p transmission distance 70m
AUDIO
Input interface 1x HDMI Type A Female N/A
Output interface
1x HDMI Type A Female 1x HDMI Type A Female
Audio formats LPCM/DTS-HD/DTS-Audio/Dolby Digital 5.1CH/Dolby Atmos
COMMAND SIGNAL
IR Interface
1x 3.5mm IR OUT Female 1x 3.5mm IR IN Female
Receiving range ≤5m
Infrared frequency 20KHz~60KHz
POWER
Power Supply
DC5V/2A PoC (Powered by TX)
Power Consumption TX+RX<5.5W
OPERATING ENVIRONMENT
Working temperature
-20°~60°C
Storage temperature -30°~70°C
Humidity 0~90% RH (No condensation)
PHYSICAL PROPERTIES
Housing
Metal
Weight TX: 130g RX: 130g
Color Black
Dimensions 75.0(L)*60.0(W)*21.0(H)mm
Protection
ESD protection; 1a Contact discharge level 2 (±4KV); 1b Air discharge level 3
(±8KV); Implementation of the standard: IEC61000-4-2
Lightning protection, Surge protection
EN - 7
WWW.TECHLY.COM
HDMI EXTENDER 4K@60HZ

Maintenance: clean only with a dry cloth. Do not use cleaning solvents or abrasives.
Warranty: no guarantee or liability can be accepted for any changes and modifications of the product
or damage caused due to incorrect use of this product.
In compliance with EU Directive WEEE this product is marked with this symbol. It means
that used electrical and electronic products should not be mixed with general household
waste.There is a separate collections system for these products in compliance with WEEE
directive, otherwise contaminative and hazardous substances can pollute the environment.
With the CE sign, Techly®ensures that the product is conformed to the basic European
standards and directives. CE declaration is available on web site at the product page.
EN - 8
WWW.TECHLY.COM
HDMI EXTENDER 4K@60HZ

EXTENDER HDMI 4K@60HZ
Gentile Cliente
Grazie per aver acquistato questo prodotto. Per ottenere il massimo delle prestazioni nella salvaguardia della
sua sicurezza, le consigliamo di leggere con attenzione il presente manuale prima di collegare e mettere in
funzione il prodotto. Tenga sempre a disposizione il presente manuale per ulteriori esigenze future.
IMPORTANTI INFORMAZIONI SULLA SICUREZZA
USO PREVISTO
Non è consentito l’uso dell’apparecchio in modi diversi da quello indicato nel
presente manuale. Utilizzare il prodotto solo in luoghi interni asciutti. Non rispettare
le istruzioni e le precauzioni di sicurezza riportate nel presente manuale potrebbe
causare incidenti mortali, lesioni e danni a persone e cose. Il costruttore/fornitore non
risponde dei danni risultanti da un utilizzo non conforme all’uso previsto.
Per ridurre il rischio di shock elettrico, questo prodotto
dovrebbe essere aperto SOLO da un tecnico autorizzato
quando è necessario ripararlo. Scollegare il prodotto
dall’alimentazione e da altri apparecchi se dovesse
esserci un problema. Non esporre il prodotto ad acqua o umidità.
ATTENZIONE
RISCHIO DI SCOSSE ELETTRICHE
NON APRIRE
• Questo prodotto non è un giocattolo e non è pensato per i bambini, contiene piccole parti che
potrebbero venir ingerite o inalate e provocare danni se non utilizzato correttamente!
• Installare l’apparecchio e le periferiche ad esso collegate in modo che non possano provocare danni
a persone e oggetti come far inciampare o causare cadute.
• Rimuovere tutti gli imballi che potrebbero causare soffocamento se manipolati da bambini.
• Evitare di installare l’apparecchio in luoghi con temperature o umidità eccessive, o luoghi che
potrebbero venire a contatto con l’acqua. Non installare vicino a bocchette dell’aria condizionata o in
luoghi che presentano polvere o fumi eccessivi. Non posizionare questo apparecchio vicino o sopra
un radiatore o un termosifone o dove è esposto alla luce solare diretta. Qualsiasi liquido che penetri
nell'apparecchio può causare guasti, incendi o scosse elettriche.
• Non utilizzare l’alimentatore se risultasse danneggiato.
• Non installare il prodotto in luoghi soggetti a vibrazioni o oscillazioni.
• Non modificare o alterare il prodotto e i suoi accessori! Non utilizzare parti danneggiate.
• Mantenere sufficiente spazio attorno alla periferica per garantire una buona ventilazione, permettere
una maggiore libertà di movimento ed evitare danni.
• Non invertire il trasmettitore da HDMI a RJ45 con il ricevitore da RJ45 a HDMI prima dell'installazione.
WWW.TECHLY.COM
IT - 9
EXTENDER HDMI 4K@60HZ

• Non scollegare la periferica durante l’uso, mantenere il prodotto distante da materiali infiammabili
ed esplosivi.
• L'elettricità statica può danneggiare il dispositivo, si prega di usare una protezione contro le cariche
elettrostatiche quando si utilizza il dispositivo.
• Per evitare scosse elettriche, assicurarsi che tutti gli apparecchi siano adeguatamente messi a terra
e non inserire mai oggetti metallici nelle parti aperte di questo apparecchio.
• Se si utilizza un alimentatore di terze parti, assicurarsi che le specifiche dell'alimentatore soddisfino
i requisiti del prodotto.
INTRODUZIONE
Questo è un kit di estensione punto-punto HDMI, può realizzare una trasmissione a latenza zero. Il
segnale HDMI 4K@60Hz può essere esteso di 50 m tramite cavo di rete CAT6/6A/7. Supporta loop
out HDMI, passthrough IR, ecc. Questo kit è una soluzione di trasmissione video affidabile e ad
altissima definizione, ampiamente utilizzata nel monitoraggio della sicurezza, nell'home theater, nella
trasmissione, nella formazione e in altri campi.
CARATTERISTICHE
1. Trasmissione a latenza zero.
2. Estendi il segnale HDMI 4K@60Hz fino a 50 m tramite cavo Cat6/6A/7.
3. Supporta HDR10.
4. Supporta il passthrough EDID e il downscaling automatico.
5. Supporta l'alimentazione del cavo di rete PoC, è necessaria solo l'alimentazione TX.
6. Il trasmettitore supporta l'uscita loop HDMI.
7. Supporta il passaggio IR.
8. Protezione contro i fulmini, protezione contro le sovratensioni, protezione ESD.
9. Collega e usa.
CONTENUTO DELLA CONFEZIONE
• Trasmettitore x1 • Ricevitore x1 • Alimentatore DC5V2A x1 • Manuale utente x1 • Cavo di prolunga
blaster IR x1 • Cavo di prolunga del ricevitore IR x1
REQUISITI DI INSTALLAZIONE
ARTICOLO DESCRIZIONE REQUISITI
Sorgente del segnale Dispositivi con porta HDMI port (PC, DVD, NVR, etc.) Cavo HDMI ≤5m
Cavo CAT6/6A/7, seguono standard IEEE-568B CAT6/6A/7≤50m
Dispositivo di
visualizzazione TV, proiettori, ecc. con porta HDMI Cavo HDMI ≤5m
WWW.TECHLY.COM
IT - 10 EXTENDER HDMI 4K@60HZ