Technics SL-1210M5GE User manual

ORDERNO. AD0303062C0
A2
TurntableSystem
SL-1210M5GE
SL-1210M5GEB
SL-1210M5GGN
SL-1210M5GPP
Colour
Black Type:SL-1210M5G
SPECIFICATIONS
Specifications
1

TURNTABLE SECTION
Type: Quartzdirectdrive
Manual turntable
Drive method: Directdrive
Motor: Brushless DC motor
Turntableplatter: Aluminum diecast
Diameter33.2cm (13-5/
64”)
Mass 1.7kg(3.74lb.)
Turntablespeeds: 33-1/3r/min, 45 r/min
Variablerangepitch: ±8%, ±16%(twosettings)
Starting torque: 1.5kg-cm (1.3lb-in)
Build-up characteristics: 0.7s. from standstill to33-
1/3r/min
Braking system: Electronicbrake
Wowand flutter: 0.01%WRMS*
0.025%WRMS (JIS C5521)
±0.035%peak(IEC98A
Weighted)
Rumble: -56dB(IEC98A
Unweighted)
-78dB(IEC98AWeighted)
*Thisrating referstoturntableassemblyalone,
excluding effectsofrecord, cartridgeor tonearm,
butincluding platter. Measuredbyobtaining signal
from built-infrequency generator ofmotor assembly.
TONEARMSECTION
Type: Universal
Effective length: 230mm (9-1/16”)
Arm heightadjustment
range: 0-6mm
Overhang: 15mm (19/32”)
Effective mass: 12g(withoutcartridge)
Offsetangle: 22°
Friction: Less than7mg(lateral,
vertical)
Tracking error angle: Within2°32’ [attheouter
groove of30cm (12”)
record]
Within0°32’ [attheinner
groove of30cm (12”)
record]
2

Styluspressure
adjustmentrange: 0-4g
Applicablecartridge
weightrange: 3.5-13g
11-20.5g(including
headshell)
(withauxiliaryweight); 9.5-13g
17-20.5g(including
headshell)
(withshell weight); 3.5-6.5g
11-14g(including
headshell)
Headshell weight: 7.5g
GENERAL
Powersupply: AC110-127V/220-240V,
50Hz
(E,EB,GN)
AC120V, 60Hz(PP)
Powerconsumption: 15W(E,EB,GN)
14.5W(PP)
Dimensions(W×H×D): 45.3×17.2×35.5cm
(17-27/32”×6-25/32”×13-31
/32”)
Mass: 11.7kg(25.74lb)
Note:
Specificationsaresubjecttochangewithoutnotice.
Mass and dimensionsareapproximate.
1
1. Accessories
3

- Disc slipsheet set (RGS0005Z-1)...1pc.
- Disc slipsheet
- Transparentsheet
- Auxiliaryweight(SFPWG17202)...1pc.
- EP record adaptor (SFWE010A)...1pc.
- Shell weight(SFPZB3501)...1pc.
- Overhang gauge(SFK0135-01)...1pc.
4

- Nuts (RHN26003)...2pcs.
- Screws(short) (SFCZV8801-1)...2pcs.
- Screws(long)(SFPEV9801-1)...2pcs.
- Washers(SFPEW9601)...2pcs.
- Sticker(RQLC0142-1)...1pc.
2. Controls
3. Turntablesystempitch adj. sliderreplacement
instructions.
5

4. SafetyPrecaution
(This“Safety Precaution”isappliedonlyinU.S.A.)
1. Beforeservicing, unplug thepowercord topreventanelectricshock.
2. Whenreplacing parts, use onlymanufacturer’srecommendedcomponents for
safety.
3. Check thecondition ofthepowercord. Replace ifwearor damageisevident.
4. Afterservicing, besuretorestoretheleaddress, insulation barriers, insulation
papers, shields, etc.
5. Beforereturning theservicedequipmenttothecustomer, besuretomake the
following insulation resistance test topreventthecustomerfrombeing exposed
toashock hazard.
Insulation Resistance Test
1. Unplug thepowercord and shortthetwoprongsoftheplug withajumperwire.
2. Turn on thepowerswitch.
3. Measuretheresistance valuewithohmmeterbetweenthejumperAC plug and
eachexposedmetal cabinet part, suchas screwheads, control shafts, handle
brackets, etc. Equipmentwithantennaterminalsshouldreadbetween3M and
5.2M toall exposedparts. (Fig. A) Equipmentwithoutantennaterminalsshould
readapproximatelyinfinity toall exposedparts. (Fig. B)
*Note:Someexposedparts may beisolatedfromthechassisbydesign. These
will readinfinity.
(Fig. A)
6

(Fig. B)
7

4. Ifthemeasurementisoutsidethespecifiedlimits, thereisapossibility ofashock
hazard. Theequipmentshouldberepairedand recheckedbeforeitisreturnedto
thecustomer.
5. Caution forACMains Lead
6. Operation Checks and Component Replacement
Procedures
8

- Thissection describes procedures for checking theoperation ofthemajor
printedcircuitboardsand replacing themaincomponents.
- For reassemblyafteroperation checks or replacement, reverse therespective
procedures. Special reassemblyprocedures aredescribedonlywhenrequired.
6.1. Checking forthemain P.C.B. and power supplyP.C.B.
9

10