Tecnoautomazione T181P User manual

EXTERNAL
RECEIVER
RC2
+5
GND
PRESS TIME BUTTON FOR 5 SECONDS
T181P. ROLLING SHUTTERS CONTROL UNIT 230 VAC POWER SUPPLY. 433.92 MHz FREQUENCY. 100 STORABLE CODES.
21 345 6 78 9 10 11 12
INPUT
34567
34567
A
B
C
RC1
GROUND
RC2
R1
R2
R3
R4
S1 S2 S3
STATUSPROGRAM
TIME
REMOTE
OUT 2 OUT 2
OUT 1 OUT 1
MOTOR
ON
OPEN
CLOSE
COM
NL
13 14 15
2019
x
230 VAC
GND
RC1
GND
+5
INTERNAL
RECEIVER
ANTENNA
21 345 6 78 9 10 11 12
ON
OFF
A
B
C
S1 S2 S3 S1 S2 S3 A
B
C
S1 S2 S3
A
B
C
21 345 6 78 9 10 11 12
123
11 12
FLASHING LAMP MAX 5W PHOTO TEST
GND
+ 24 VDC
9 108
STOP
5678910 11 123 4 5678 9 10 11 123 4
MOTOR
13 14 15
M
POWER SUPPLY
X
N
L
1920
5678 9 10 11 123 45678 9 10 11 123 4
PHOTOCELL RECEIVER
56789
RX GND
+VDC
10 11 123 4
N.C.
56789
TEST
GND
10 11 123 4
TX
FLASHING LAMP
OUT2. ENABLED DURING
OPENING, CLOSING AND
PAUSE. Ideal for 230V flashing lamp.
OUT1. ENABLE OR
DISABLEVIA REMOTE.
OUT 1 OUT 2
AUXILIARY OUTPUTS
5678910 11 123 4
MAX 5 W
COURTESY LIGHT 230 VAC
TERMINAL BLOCK:
3. OPEN / DEAD-MAN CLOSE
4. CLOSE / DEAD-MAN CLOSE
5. STOP
6. PHOTOCELL
7. START / DEAD-MAN OPEN
8. +VDC / COMMON / +24VAC
9. PHOTOCELLS TEST
10. GND
11.12. FLASHING LAMP
13. MOTOR CLOSE
14. MOTOR COMMON
15. MOTOR OPEN
20.X.19. 230 VAC (FLASHING LAMP STEADY)
BOARD STATUS:S1 S2 S3
STAND BY, ROLLING SHUTTER CLOSED
ROLLING SHUTTER IN OPENING OR
CLOSING PHASE, ROLLING SHUTTER
OPEN ON GOING PROGRAMMING
PHOTOCELLS TEST ERROR
COURTESY LIGHT ERROR
PROGRAMMING ERROR:
INCORRECT PROCEDURE
CONTROL BOARD IN PROGRAMMING
PHASE
2A FUSE
LEDs:
S1.S2.S3. ROLLING SHUTTER STATUS / CONTROL BOARD STATUS LEDS
RC1. SHOWS THAT A SIGNAL HAS BEEN RECEIVED FROM THE INTERNAL RADIO RC1
RC2. SHOWS THAT A SIGNAL HAS BEEN RECEIVED FROM THE EXTERNAL RADIO RC2
R1. START / OPEN OR DEAD-MAN OPEN
R2. STOP STOP THE ROLLING SHUTTER
R3. START / FAST CLOSURE OR DEAD-MAN CLOSURE
R4. OUT1 ON/OFF: light on enable or disable OUT1. Courtesy light will automacally switch off aer the
me programmed with DIP 11 and DIP 12. OUT1 is enabled and disabled via remote and will not switch off automacally.
A. C. PROGRAMMING LEDSB.
1.2.3.4.5.6.7. INPUTS
AUXILIARY OUTPUTS:
OUT1. ENABLED/DISABLED VIA REMOTE (R4)
OUT2. ENABLED DURING OPENING, CLOSING AND PAUSE. IDEAL FOR 230V FLASHING LAMP.
TERMINAL BLOCK CONNECTIONS
START OR DEAD-MAN OPEN
OPEN OR DEAD-MAN OPEN CLOSE OR DEAD-MAN CLOSE
PHOTOCELL TRANSMITTER
PROGRAMMING ROLLING SHUTTER WORKING TIMES. The programming must be operated while the rolling shuer is closed.
To start the procedure
DIP 3 - 4 - 5 must be set
to OFF posion.
Led A is steady on.
The rolling shuer opens.
The working me is being
acquired. The rolling shuer
reaches the limit switch.
PRESS THE TIME BUTTON
or a start command PRESS THE TIME BUTTON or a start command
This step depends on
the working mode set.
Led A s steady on. The rolling
shuer is stopped completely
opened. Led C flashing every
second. The automac closure
me is being acquired, (pause
me during opening).
The programming has ended.
The rolling shuer closes.
OUT2. ENABLED DURING OPENING, CLOSING AND PAUSE. IDEAL FOR 230V FLASHING LAMP.

21 345 6 78 9 10 11 12 DIP 6 ON
MOTOR POWER
21 345 6 78 9 10 11 12 21 345 6 78 9 10 11 12 21 345 6 78 9 10 11 12 21 345 6 78 9 10 11 12
DIP 3 OFF
DIP 4 OFF
DIP 5 OFF
21 345 6 78 9 10 11 12
DIP 3 ON
DIP 4 OFF
DIP 5 OFF
21 345 6 78 9 10 11 12
DIP 3 OFF
DIP 4 ON
DIP 5 OFF
21 345 6 78 9 10 11 12
DIP 3 ON
DIP 4 ON
DIP 5 OFF
21 345 6 78 9 10 11 12
DIP 3 OFF
DIP 4 OFF
DIP 5 ON
21 345 6 78 9 10 11 12
DIP 3 ON
DIP 4 OFF
DIP 5 ON
21 345 6 78 9 10 11 12
WORKING TIMES
DIP 3 OFF
DIP 4 ON
DIP 5 ON
21 345 6 78 9 10 11 12
DIP 3 ON
DIP 4 ON
DIP 5 ON
21 345 6 78 9 10 11 12
40%
DIP 1 OFF
DIP 2 OFF
60%
DIP 1 ON
DIP 2 OFF
80%
DIP 1 OFF
DIP 2 ON
100%
DIP 1 ON
DIP 2 ON
PHOTOCELLS TEST
DISABLED
21 345 6 78 9 10 11 12 DIP 6 OFF
LOGIC INPUT FUNCTIONS
21 345 6 78 9 10 11 12 DIP 10 OFF 21 345 6 78 9 10 11 12 DIP 10 ON
COURTESY LIGHT
21 345 6 78 9 10 11 12 21 345 6 78 9 10 11 12 21 345 6 78 9 10 11 12 21 345 6 78 9 10 11 12
DIP 11 OFF
DIP 12 OFF
1 minut
DIP 11 ON
DIP 12 OFF
3 minutes
DIP 11 OFF
DIP 12 ON
5 minutes
DIP 11 ON
DIP 12 ON
10 minutes
21 345 6 78 9 10 11 12
R1 DEAD-MAN OPEN
R2 STOP
R3 DEAD-MAN CLOSE
R4 OUT1 ON/OFF
563 47
dead-man
open stop photocell
dead-man
close
21 345 6 78 9 10 11 12
R1 OPEN
R2 STOP
R3 DEAD-MAN CLOSE
R4 OUT1 ON/OFF
563 47
open stop photocell open
21 345 6 78 9 10 11 12
R1 OPEM
R2 STOP
R3 CLOSE
R4 OUT1 ON/OFF
563 47
stop start
21 345 6 78 9 10 11 12
R1 OPEN
R2 STOP
R3 CLOSE
R4 OUT1 ON/OFF
563 47
stop start
21 345 6 78 9 10 11 12
R1 START
R2 STOP
R3 START + FAST CLOSURE
R4 OUT1 ON/OFF
563 47
stop start
21 345 6 78 9 10 11 12
R1 START
R2 STOP
R3 START + FAST CLOSURE
R4 OUT1 ON/OFF
563 47
stop start
21 345 6 78 9 10 11 12
R1 START
R2 STOP
R3 START + FAST CLOSURE
R4 OUT1 ON/OFF
563 47
open close stop photocell start
21 345 6 78 9 10 11 12
R1 START
R2 STOP
R3 START + FAST CLOSURE
R4 OUT1 ON/OFF
56
4
3 7 start
DIP 7 ON / DIP 8 ON / DIP 9 OFF / FUNTIONS: STEP-BY-STEP + AUTOMATIC CLOSURE + FAST CLOSURE (R3) + PHOTOCELLS TEST (DIP 6)
DIP 7 OFF / DIP 8 OFF / DIP 9 ON / FUNCTIONS: OPEN (R1)-CLOSURE (R3) + AUTOMATIC CLOSURE + PHOTOCELLS TEST (DIP 6)
standard
community mode
step-by-step
step-by-step
+
automac closure
open-close
+
automac closure
open-close
open
dead-man close
dead-man open
dead-man close
DIP 7 OFF / DIP 8 ON / DIP 9 ON / FUNZIONI: DEAD-MAN CLOSE
DIP 7 ON / DIP 8 ON / DIP 9 ON / FUNCTIONS: DEAD-MAN OPEN + DEAD-MAN CLOSE
DIP 7 ON / DIP 8 OFF / DIP 9 ON / FUNCTIONS: OPEN (R1)-CLOSURE (R3) + PHOTOCELLS TEST (DIP 6)
dead-man
open
TRANSMITTERS FUNCTIONS
dead-man
close
SEQUENTIAL PROGRAMMING USING TIME BUTTON
OPENING=CLOSING: programmable from 0 to 240 seconds (4 minutes)
AUTOMATIC CLOSURE=PAUSE TIME DURING OPENING: programmable from 0 to 240 Seconds (4 minutes)
The automac closure depends on the programmed LOGIC of DIPS 7.8.9.
OPENING=CLOSING: 25 seconds
AUTOMATIC CLOSURE=PAUSE TIME DURING OPENING: 20 seconds
OPENING=CLOSING: 33 seconds
AUTOMATIC CLOSURE=PAUSE TIME DURING OPENING: 20 seconds
OPENING=CLOSING: 40 seconds
AUTOMATIC CLOSURE=PAUSE TIME DURING OPENING: 20 seconds
OPENING=CLOSING: 25 seconds
AUTOMATIC CLOSURE=PAUSE TIME DURING OPENING: 40 seconds
OPENING=CLOSING: 33 seconds
AUTOMATIC CLOSURE=PAUSE TIME DURING OPENING: 40 seconds
OPENING=CLOSING: 40 seconds
AUTOMATIC CLOSURE=PAUSE TIME DURING OPENING: 40 seconds
OPENING=CLOSING: 50 seconds
AUTOMATIC CLOSURE=PAUSE TIME DURING OPENING: 40 seconds
The photocells test depends on the programmed LOGIC of DIPS 7.8.9.
PHOTOCELLS ARE CHECKED
BEFORE ANY MOVEMEN.
DIP 7 OFF / DIP 8 OFF / DIP 9 OFF / FUNCTIONS: AUTOMATIC CLOSURE + FAST CLOSURE(R3) + PHOTOCELLS TEST (DIP6)
DIP 7 ON / DIP 8 OFF / DIP 9 PFF / FUNCTIONS: COMMUNITY MODE +AUTOMATIC CLOSURE + FAST CLOSURE(R3) + PHOTOCELLS TEST (DIP6)
DIP 7 OFF / DIP 8 ON / DIP 9 OFF / FUNCTIONS: STEP-BY-STEP MODE + FAST CLOSURE(R3) + PHOTOCELLS TEST (DIP6)
open close stop photocell
open close photocell
open close photocell
open close photocell
open close photocell
DISABLE NOT WIRED N.C. INPUTS
N.C.
INPUTS ENABLED
Not wired N.C. inputs disabled (stop and photocells) when
a disabled N.C. input is wired, it is automacally enabled
regardless of the dip posion.
The courtesy light is on when the rolling shuer moves. It switches off automacally aer the me set with DIP 11 and DIP 12.
The courtesy light can be switched on via a remote that has a R4 funcon memorized.

OUT1 ON/OFF
R1. OFF
R2. OFF
R3. OFF
R4. ON
X1
START OR OPEN OR
DEAD-MAN OPEN
R1. ON
R2. OFF
R3. OFF
R4. OFF
X4
STOP
R1. OFF
R2. ON
R3. OFF
R4. OFF
X3
START OR FAST CLOSURE OR
CLOSE OR DEAD-MAN CLOSURE
R1. OFF
R2. OFF
R3. ON
R4. OFF
X2
RC1
RC2
ON
R1. OFF
R2. OFF
R3. OFF
R4. ON
X4
RC1
RC2
ON
R1. OFF
R2. OFF
R3. ON
R4. OFF
X3
R1. OFF
R2. ON
R3. OFF
R4. OFF
X2
R1. ON
R2. OFF
R3. OFF
R4. OFF
X1
STOP OUT1 ON/OFF
DEAD-MAN OPEN: OPENS UNTIL THE COMMAND IS ENABLED. The dead-man command takes precedence over stop and photocells securies.
DEAD-MAN CLOSURE: CLOSES UNTIL THE COMMAND IS ENABLED. The dead-man command takes precedence over stop and photocells securies.
DISABLE NOT WIRED N.C. INPUTS: DISABLE ALL NOT WIRED N.C. INPUTS. IF ANY N.C. INPUT IS THEREAFTER WIRED THE CONTROL UNIT WILL
AUTOMATICALLY ENABLE IT REGARDLESS OF THE DIP POSITION. DURING DEAD-MAN OPERATING LOGIC THE PHOTOCELLS TEST IS NOT EXECUTED
REGARDLESS OF THE DIP POSITION.
COMMUNITY MODE:
•During closing: the start commands invert the door movement.
•During opening: the start commands are ignored.
STEP-BYSTEP:
•During closing: the start commands stop the door movement.
•During opening: the start commands stop the door movement.
AUTOMATIC CLOSURE: ROLLING SHUTTER CLOSES AUTOMATICALLY AFTER THE THE PROGRAMMED AUTOMATIC CLOSURE TIME.
IF THE AUTOMATIC CLOSURE IS DISABLED THE ROLLING SHUTTER REMAINS OPENED AFTER THE OPENING PHASE.
FAST CLOSURE: DURING OPENING THE ROLLING SHUTTER CLOSES 3 SECONDS AFTER THE PHOTOCELLS ACTIVATION. THIS FUNCTION CAN BE
ACTIVATED ONCE EVERY WORKING CYCLE AND ONLY IF THE ROLLING SHUTTER MOVEMENT HAS NEVER BEEN STOPPED DURING THE OPENING
OR DURING THE TIME OF AUTOMATIC CLOSURE.
R1. ON
R2. ON
R3. ON
R4. ON
R1. OFF
R2. OFF
R3. OFF
R4. OFF
R1. OFF
R2. ON
R3. ON
R4. ON
R1. OFF
R2. OFF
R3. ON
R4. ON
R1. OFF
R2. OFF
R3. OFF
R4. ON
ERASE ALL REMOTES
TO ERASE ALL SAVED REMOTES PRESS AND HOLD THE REMOTE BUTTON ON THE BOARD FOR 6 SECONDS. LEDS R1, R2, R3, AND R4 WILL GO ON
STEADY THEN WILL GO OFF INDICATING CORRECT DELETION OF ALL REMOTES.
PRESS AND HOLD THE REMOTE
BUTTON ON THE BOARD FOR
ABOUT 6 SECONDS.
SUGGESTIONS
THE RADIO CASE CAN BE
INSTALLED IN COMBINATION
WITH THE FLASHING LAMP ONE UP.
THE RADIO
MODULE
HOUSED INSIDE
THE RADIO CASE
(RANPC5T).
TO INCREASE THE SIGNAL RANGE DISCONNECT THE RADIO MODULE FROM THE INTERNAL RECEIVER
POSITION AND WIRE IT ON THE TERMINAL BLOCK EXTERNAL RECEIVER POSITION. IF AVAILABLE, WE
SUGGEST YOU USE THE RADIO CASE (CODE RANPC5T).
1. RADIO MODULE CONNECTED IN
INTERNALRECEIVER POSITION
(DEFAULT CONFIGURATION).
2. DISCONNECT THE RADIO
MODULE FROMTHE INTERNAL
RECEIVER POSITION.
3. WIRE THE RADIO MODULE ON THE
TERMINAL BLOCK EXTERNAL RECEIVER
POSITION.
3. WIRE THE RADIO MODULE
ON THE TERMINAL
BLOCK EXTERNAL
RECEIVER
POSITION.
x x x
MEMORIZE A REMOTE
DELETE A REMOTE
START OR OPEN OR
DEAD-MAN OPEN START OR FAST CLOSURE OR CLOSE OR DEAD-MAN CLOSURE
PRESS AND HOLD THE DESIRED BUTTON ON THE REMOTE, SIMULTANEOUSLY PRESS ONCE THE REMOTE BUTTON ON THE CONTROL BOARD TO
MEMORIZE THE START OR OPEN OR DEAD-MAN OPEN FUNCTIONS, PRESS TWICE THE REMOTE BUTTON ON THE BOARD TO MEMORIZE THE STOP
FUNCTION, PRESS THREE TIMES THE REMOTE BUTTON ON THE BOARD TO MEMORIZE THE START OR FAST CLOSURE OR DEAD-MAN CLOSURE
FUNCTIONS, PRESS FOUR TIMES THE REMOTE BUTTON ON THE BOARD TO MEMORIZE THE OUT1 ON/OFF FUNCTION. THE CORRESPONDING LED
(R1-START, R2-STOP, R3-PEDESTRIAN, OR R4-OUT1) WILL BE STEADY ON TO CONFIRM MEMORIZATION.
PRESS AND HOLD THE DESIRED BUTTON ON THE REMOTE, SIMULTANEOUSLY PRESS FOUR TIMES THE REMOTE BUTTON ON THE CONTROL BOARD
TO DELETE THE START OR OPEN OR DEAD-MAN OPEN FUNCTIONS, PRESS THREE TIMES THE REMOTE BUTTON ON THE BOARD TO DELETE THE
STOP FUNCTION, PRESS TWICE THE REMOTE BUTTON ON THE BOARD TO DELETE THE START OR FAST CLOSURE OR DEAD-MAN CLOSURE
FUNCTIONS, OR PRESS ONCE THE REMOTE BUTTON ON THE BOARD TO DELETE THE OUT1 ON/OFF FUNCTION.
FUNCTIONS DESCRIPTION / MODES

MADE IN ITALY
T.A. Tecno Automazione s.r.l. - Via Vicinale snc - 03018 - Paliano - (FR) - Italy - Tel [phone] - Fax [phone] - [email protected] - www.tecnoautomation.com - www.tecnoautomazione.com
USER MANUAL
T181P
ENG
For private households: Informaon on Disposal for Users of WEEE This symbol on the product(s) and / or accompanying documents means that used electrical and electronicequipment (WEEE)
should not be mixed with general household waste. For proper treatment, recovery and recycling, please take this product(s) to designated collecon points where it will be accepted free of
charge. Alternavely, in some countries, you may be able to return your products to your local retailer upon purchase of an equivalent new product. Disposing of this product correctly will help
save valuable resources and prevent any potenal negave effects on human health and the environment, which could otherwise arise from inappropriate waste handling. Please contact your
local authority for further details of your nearest designated collecon point. Penales may be applicable for incorrect disposal of this waste, in accordance with you naonal legislaon. For
professional users in the European Union If you wish to discard electrical and electronic equipment (EEE), please contact your dealer or supplier for further informaon. For disposal in countries
outside of the European Union This symbol is only valid in the European Union (EU). If you wish to discard this product please contact your local authories ordealer and ask for the correct
method of disposal.