TECOM xDAQ-600 User manual

1
Copyright © 2020, All Rights Reserved.
Ver: D01 D/C: 109-0414
xDAQ-600 / xDAQ-600(P)
A Piezo Vibration Analysis and
Diagnosis Unit
Operation Manual
V1.1

xDAQ-600 / xDAQ-600 (P) Operation Manual
Page 2
目錄
Start Up............................................................................................................................................... 3
1. Device Info .................................................................................................................................... 4
1.1 Status Overview ............................................................................................................... 4
1.2 DHCP Client List ............................................................................................................... 4
1.3 System Log ........................................................................................................................ 5
1.4 Change Setting Log ........................................................................................................ 5
1.5 Device Alarm History...................................................................................................... 6
2. Settings .......................................................................................................................................... 7
2.1 LAN...................................................................................................................................... 7
2.2 WAN .................................................................................................................................... 7
2.3 Unit Pairing........................................................................................................................ 8
2.4 RS485 ................................................................................................................................ 11
2.5 Maintenance Info .......................................................................................................... 19
3. Wireless........................................................................................................................................ 21
3.1 WiFi Mode Setting......................................................................................................... 21
3.2 Basic Wireless Settings................................................................................................. 22
3.3 AP+STA Mode ................................................................................................................ 24
4. System Management ............................................................................................................... 28
4.1 Basic Settings.................................................................................................................. 28
4.2 Settings Management (Configuration File) ........................................................... 29
4.3 Certificate Update ......................................................................................................... 30
4.4 Firmware Update ........................................................................................................... 30
4.5 Log Level .......................................................................................................................... 31

xDAQ-600 / xDAQ-600 (P) Operation Manual
Page 3
Start Up
Users use the browser (default IP: 192.168.168.10, account: admin, password:
IP585xAdmin), and the homepage provides links to AG300 related functions.
System login screen:
After successful login, the system will list the current status information, the page is as
follows:
Users can set the project into four major items: "Device info", "Settings", "wireless",
and "System Management".

xDAQ-600 / xDAQ-600 (P) Operation Manual
Page 4
1. Device Info
The device information includes five items: "Status Overview", "DHCP Client List",
"System Log", "Change Setting Log", and "Device Alarm History".
1.1 Status Overview
Users can use this project to obtain basic system information and network settings.
The page is as shown in the figure above.
1.2 DHCP Client List
Users can use this project to obtain DHCP client data.

xDAQ-600 / xDAQ-600 (P) Operation Manual
Page 5
1.3 System Log
Users can use this project to obtain system log data.
1.4 Change Setting Log
The operation history is listed in the List directory. It can be exported via the "Export"
button.

xDAQ-600 / xDAQ-600 (P) Operation Manual
Page 6
1.5 Device Alarm History
Users can use this project to view the alarm records of all devices.

xDAQ-600 / xDAQ-600 (P) Operation Manual
Page 7
2. Settings
Usage settings include "LAN", "WAN", "Unit Paring", "RS485", "Maintenance info" sub-
items.
2.1 LAN
Users can use this project to set LAN settings, the page is shown as below:
2.2 WAN
Users can use this project to set up the WAN. The page is as shown below:
"Remote Access" can configure projects that allow remote access:
"Secure HTTP" can enable or disable remote HTTPS access
"Normal HTTP" can enable or disable remote HTTP access
"Remote Login" can enable or disable remote login

xDAQ-600 / xDAQ-600 (P) Operation Manual
Page 8
2.3 Unit Pairing
Users can register through the webpage, as shown below :

xDAQ-600 / xDAQ-600 (P) Operation Manual
Page 9
1. Press the "Add" button to automatically create a new terminal device.
2. Check the newly generated terminal device, and press the "Edit" key to enter the
editing screen, you can edit the various information of the terminal device.
-Name: Fill in the appropriate name according to personal needs.
-Type: Smartphone.
-Account: Please enter the number within 100 ~ 109, and this number cannot be
the same as other registered terminal equipment.
-Password: can be reconfigured according to personal needs.

xDAQ-600 / xDAQ-600 (P) Operation Manual
Page 10
3. After editing the information, press the "Save" button, and then press the "Start
Pairing" button to enter the device registration program.
4. After successful registration, the status will show "Connected".

xDAQ-600 / xDAQ-600 (P) Operation Manual
Page 11
2.4 RS485
Users can use this project to add equipment, set and view equipment parameters, and
configure the “Alarm Trigger Time”of the alarm and the “Start Address”of the
equipment.
1>. Add Motor：
1. Select the "Add" button in the motor, enter the configuration parameters, and click
"Save" to add a motor.

xDAQ-600 / xDAQ-600 (P) Operation Manual
Page 12
Some parameters are explained as follows:
Name: fill in as required
Work ID : Motor factory ID
Drive Mode : direct drive and inverter drive
Control point : Configure DO
FAE Information : Contact Information for Equipment Maintenance Personnel
Engineer Information : Factory Technician Contact
2. After adding the motor, you can add IEPE below.
3. Add an IEPE, select "+", and complete the IEPE setting in the pop-up box. Click the
"Save" button to save.

xDAQ-600 / xDAQ-600 (P) Operation Manual
Page 13
Some parameters are explained as follows:
Line : Choose to use the first set of lines (1) or the second set of lines (2)
Name : can be filled as required
Vibration
Name : fill in as required
Velocity RMS
Up Limit : When the vibration reaches this set value, an alarm will be issued. Please
fill in (mm / s) according to the specifications.
Up Early Warning : When the vibration reaches this set value, a warning
notification is issued. Please fill in (mm / s) according to the specifications.
Low : minimum vibration setting value, please fill in according to the specification
(mm / s).
High : The highest vibration setting value, please fill in according to the
specification (mm / s).
Sudden Change
Amplitude : Please fill in the value (mm / s) as required (if no value is filled in, this
function will be automatically turned off).
Time : Please fill in the value according to the requirements, the range is 5-60.
Acceleration RMS

xDAQ-600 / xDAQ-600 (P) Operation Manual
Page 14
Up Limit : When this set value is reached, an alarm will be issued. Please fill in (mm
/ s²) according to the specifications.
Up Early Warning : When the set value is reached, a warning notification is issued.
Please fill in according to the specifications (mm / s²).
Low : The lowest setting value, please fill in according to the specifications (mm /
s²).
High : The highest setting value, please fill in according to the specifications (mm /
s²).
Sudden Change
Amplitude : Please fill in the value (mm / s²) as required (if no value is filled in, this
function will be automatically turned off).
Time : Please fill in the value according to the requirements, the range is 5-60.
Displacement
Up Limit : When this set value is reached, an alarm will be issued. Please fill in (mm)
according to the specifications.
Up Early Warning : send pre-warning notice when reaching this set value, please fill
in (mm) according to specifications.
Low : The lowest setting value, please fill in (mm) according to the specifications.
High : The highest setting value, please fill in (mm) according to the specifications.
Sudden Change
Amplitude : Please fill in the value (mm) as required (if the value is not filled in, this
function will be automatically turned off).
Time : Please fill in the value according to the requirements, the range is 5-60.
Kurtosis
Up Limit : When this set value is reached, an alarm is issued.
Up Early Warning : A warning notification is issued when this set value is reached.
Low : The lowest setting value.
High : The highest setting value.
After adding, you can click the configuration icon to modify the parameters of IEPE.

xDAQ-600 / xDAQ-600 (P) Operation Manual
Page 15
4. XDAQ600 (P) additionally contains PMS related setting parameters, as shown
below：

xDAQ-600 / xDAQ-600 (P) Operation Manual
Page 16
PMS parameters are described as follows :
Field
Description
Sample Rate
Keep it the same as DAQ setting
Sample Number
Keep it the same as DAQ setting
Fa (Spinning) in RPM
Motor spinning speed in RPM
Threshold
There are 17 known defects. The application will
calculate the confidence level of each defects. Only
when the confident level > Threshold will be shown in
the diagnosis information field.
Contact Angle
Contact Angle
Bearing Diameter
The theoretical median diameter of a bearing, which
passes through the center of the balls.
Number of Balls
Number of balls
Ball Diameter
Diameter of balls
Inner Frequency
Ball Pass Frequency of Inner Ring
Outer Frequency
Ball Pass Frequency of Outer Ring
Roller Frequency
Ball Spin Frequency
Number of Rotors
Number of rotor bars in a motor
Fp(Driven Gear)
The output speed of a gear box

xDAQ-600 / xDAQ-600 (P) Operation Manual
Page 17
Number of Gears
The number of teeth of first driven gear.
Low frequency
Ignore frequency lower than low frequency
High frequency
Ignore frequency higher than high frequency
Note : The PMS parameters are supported for xDAQ-600 (P) only.
2>. Add the switchgear :
1. Select the "Add" button in the switchgear, enter the parameter configuration, and
click "Save" to add a switchboard.
3>. Add other devices:
1. Select the "Add" button in other devices, enter the parameter configuration, and
click "Save" to add another device.

xDAQ-600 / xDAQ-600 (P) Operation Manual
Page 18
2. After adding other devices, you can add IEPE below.

xDAQ-600 / xDAQ-600 (P) Operation Manual
Page 19
2.5 Maintenance Info
Users can use this project to add contact information of equipment maintenance
personnel and factory technicians.
1. Click "Add", enter name and phone number, save and add a contact.

xDAQ-600 / xDAQ-600 (P) Operation Manual
Page 20
2. After checking the contact list, click the "Edit" or "Delete" button to edit or delete a
record.
3. Contacts can be selected on the device's settings page :