Tecomec ISOBUS ECU1224 User manual

P00801580 ECU 1224 ISOBUS SPRAYER: Quick Reference Rev 0
ISOBUS ECU1224 SPRAYER
Connect your sprayer to Any ISOBUS tractor !
Quick reference
ECU Manufacturer : Tecomec Srl
Hardware ID: 00284
Software version . ECU-1224 ISOBUS 2.5.0#

Intended USE
INTRODUCTION
P00801580 ECU 1224 ISOBUS SPRAYER: Quick Reference Rev 2. 2/24
Congratulations Dear User,
You have chosen a product by Tecomec, a leading company in the development
and production of electronic systems for agriculture. This manual provides
information about operating and maintaining. For your safety and the safety of the
people working with this equipment, is very important that you read the manual
carefully before using this system.
Proper maintenance extends the life of the product and ensures the safe operation
of the system.
The manufacturer reserves the right to redesign and change the system as
necessary without notification.
ECU 1224 is an Electronic Control Unit ISOBUS AEF certified, dedicated to sprayer
implement. ECU1224 is a rate controller capable of Automatic Section Control
when connected to ISOBUS Virtual Terminal enabled for GPS navigation. This
device works only with certified ISOBUS VT, please verify documentation of your VT
installed on the tractor.
Find complete user manual at WWW.TECOMEC.COM
User manual

Intended USE
CONFORMANCE
P00801580 ECU 1224 ISOBUS SPRAYER: Quick Reference Rev 2. 3/24
INTENDED USE
ISOBUS ECU 1224 is high performance electronic control unit for liquid distribution,
specially designed to work on agricultural machinery for spraying. The accurate
control of the sprayer parameters increases the effectiveness and efficiency of the
treatments, reducing the waste of chemicals.
ISOBUS ECU 1224 is certified ISO 11783. The ISO 11783 standard protocol usually
called ISOBUS protocol is the result of an agreement between the main
manufacturers of agricultural machinery and equipment. ISOBUS allows
communication between the ISOBUS display installed in most recent tractors and
sprayers, seeder etc. A unique display in the cabin (called Virtual Terminal) will
control your implement, avoiding expensive and bulky proprietary displays. The
certification guarantees you full compatibility with all ISOBUS certified tractor’s
consoles.
LEGEND
This user’s manual uses some conventional signs and words, to lead the user during
the reading of important instructions and advices; these concern especially the
setting of the parameters of the system and thus its correct working.
INFO : Indicates further explaining and information.
DANGER: Indicates an imminently hazardous situation that, if not avoided, could result in
DEATH OR VERY SERIOUS INJURY.
WARNING Indicates a potentially hazardous situation that, if not avoided, may result in
MINOR INJURY or system damage
RECOMENDATION
WARNING: Before operating or installing this equipment read and understand
manual and all safety information. Good safety practices protect operators from
injuries. Safety practices reported in this manual do not override standard good
practice.

Intended USE
CONFORMANCE
P00801580 ECU 1224 ISOBUS SPRAYER: Quick Reference Rev 2. 4/24
WARNING: Always check that any suspended vehicle attachments are lowered to
the ground before beginning repair or maintenance work on a vehicle.
WARNING The power supply must be protected with fuse (10A recommended).
Tecomec s.r.l is not responsible for damages to ISOBUS ECU1224.
WARNING: Disconnect power supply cable ECU when battery is undergoing
recharge. If it is not the case Tecomec s.r.l is not responsible for damages to the
ECU1224.
WARNING: Disconnect power supply ECU before reparations, or welding procedure
on the vehicle. If it is not the case, Tecomec s.r.l is not responsible for damages to
the ECU.
WARNING: For a correct functioning, please make sure that the battery voltage is
higher than 10, 5 Volt.
WARNING: This marking on the product or on its packaging illustrates that this
product may not be disposed of with normal household waste. The user is
responsible for the disposal of this equipment through a
designated collection of electrical and electronic equipment. To
determine where to dispose of such electrical and electronic
waste, contact the government office, the waste disposal
organization serving the family, or the company where the
product was purchased.
WARNING: Before cleaning the implement with high pressure
water jets, protect the equipment from water. Do not orientate
high pressure water jet directly on ECU or cables connected to
ECU 1224.
WARNING: Clean equipment using a soft, damp, lint-free cloth.
Do not use sprays, solvents, abrasives, or sharp or pointed objects
that could damage ECU1224.
WARNING: Wear appropriate protective clothing for the task being undertaken and
conditions.
WARNING: ECU helps the operator to regulate rate control and automatic section
control, but the operator remains the responsible for all the activities. Operator
must keep the control of the vehicle all time. The operator is ultimately responsible

Intended USE
CONFORMANCE
P00801580 ECU 1224 ISOBUS SPRAYER: Quick Reference Rev 2. 5/24
for safe operation of this equipment, preventing and repairing faulty parts and
calibration.

Intended USE
P00801580 ECU 1224 ISOBUS SPRAYER: Quick Reference Rev 2. 6/24
COMPONENTS
COMPONENTS
Figure 1 Kit composition
INSTALLATION DIAGRAM
Figure 2Installation Diagram
PART
Description
PART
Description
A
Driver ISOBUS ECU 1224
I
Pump
--
----------
J
External Switch Main Valve
--
----------
L
Tank
D
Speed sensor (Optional)
N
Sprayer Boom
E
Output 12V max 1.5 A
C1
Main cable
F
Level Sensor (Optional)
C2
Gray connector valve cable
G
Pressure sensor (Optional)
C3
Brown connector valve cable
H
Electric valves
T1
ISOBUS T

Intended USE
P00801580 ECU 1224 ISOBUS SPRAYER: Quick Reference Rev 2. 7/24
COMPONENTS
MECHANICAL FIXING
Figure 3 Mechanical Installation

Intended USE
START
P00801580 ECU 1224 ISOBUS SPRAYER: Quick Reference Rev 2. 8/24
Figure 4 Main
Figure 5 Working Interface

Intended USE
START
P00801580 ECU 1224 ISOBUS SPRAYER: Quick Reference Rev 2. 9/24
Figure 7 Manual Section Control
Figure 6 Main

Intended USE
SECTIONS CONTROL
P00801580 ECU 1224 ISOBUS SPRAYER: Quick Reference Rev 2. 10/24
Figure 8 Automatic Section Control
Figure 9 Automatic Section Control Prescription Map

Intended USE
DIRECT SPRAYING
P00801580 ECU 1224 ISOBUS SPRAYER: Quick Reference Rev 2. 11/24
Figure 10 Direct Mode

Intended USE
RESET COUNTERS
P00801580 ECU 1224 ISOBUS SPRAYER: Quick Reference Rev 2. 12/24
Figure 11 Reset Counters
Figure 12 Reports

Intended USE
TRAILED SPRAYER
P00801580 ECU 1224 ISOBUS SPRAYER: Quick Reference Rev 2. 13/24
Figure 13 Dimensions configuration
Figure 14 Trailed sprayer

Intended USE
THREE POINT LINKAGE
P00801580 ECU 1224 ISOBUS SPRAYER: Quick Reference Rev 2. 14/24
Figure 15 Dimension Configuration
Figure 16 Three point linkage

Intended USE
BOOM
P00801580 ECU 1224 ISOBUS SPRAYER: Quick Reference Rev 2. 15/24
Figure 17 Boom Settings
Figure 18 Boom Diagram

Intended USE
Sensor:Flowmeter
P00801580 ECU 1224 ISOBUS SPRAYER: Quick Reference Rev 0. 16/24
Figure 19 Flow meter regulation sensor
Figure 20Flow meter regulation sensor(b)

Intended USE
Sensor:Flowmeter
P00801580 ECU 1224 ISOBUS SPRAYER: Quick Reference Rev 0. 17/24
Figure 21 Pressure regulation sensor
Figure 22 Pressure regulation sensor (b)

Intended USE
Sensor:Flowmeter
P00801580 ECU 1224 ISOBUS SPRAYER: Quick Reference Rev 0. 18/24
This product has been designed and manufactured using the most modern
techniques. The manufacturer guarantees the products for 24 months from the date of
purchase.
Tecomec S.r.l. guarantees that ISOBUS ECU 1224 SPRAYER labeled products are
covered against manufacturing defects during the following periods.
Warranty periods
•Finished products –2 years from Invoice date to end user
•Warranty on parts or reparation made during warranty period will
end at the end of initial warranty period.
Product warranty terms
1. The warranty period starts at the date of purchase. The guarantee
will be applied upon presentation of the purchase invoice. The
manufacturer, acting through the sales and technical assistance
network, shall replace free of charge any defective component. The
warranty does not modify the purchaser’s rights as established
under legislation governing the consequences of defects in the
product.
2. The technical staff will intervene as soon as possible within the time
limits granted by organizational arrangements.
3. Any claim under the warranty, must include details of invoice or
receipt showing the date of purchase.

Intended USE
Sensor:Flowmeter
P00801580 ECU 1224 ISOBUS SPRAYER: Quick Reference Rev 0. 19/24
4. The manufacturer excludes consumables and parts subject to
normal wear and tear.
5. The guarantee excludes intervention for updating and improvement
of product.
6. The warranty does not cover the tuning maintenance interventions
which should occur during the period of guarantee.
7. Any damage caused during transport must be reported immediately
to the carrier or warranty will be void.
8. The warranty does not cover any damage, direct or indirect, caused
to people or things
9. The warranty is void in the event of:
•Obvious lack or wrong installation or maintenance.
•Use of not original spare parts or accessories
•Interventions carried out by non-authorized personnel.
Returning goods
To have an effective guarantee, it is necessary to comply with the following
requirements:
•The product must be delivered in the original packaging and with all
the accessories (if applicable) in good condition.
•Provide a copy of the purchase invoice.
•Attach a letter in writing (from the distributor or user) explaining in
detail the equipment failures and / or anomalies, mentioning the
device serial number.

Intended USE
Sensor:Flowmeter
P00801580 ECU 1224 ISOBUS SPRAYER: Quick Reference Rev 0. 20/24
•Get the official approval from the seller before returning any goods
Notes
•Customer is not allowed to rework or try to repair the device under
any conditions. Reworked devices will not be covered by warranty.
•The guarantee will be applied after the analysis of technical staff
which will carry out the necessary tests for diagnosis.
•Parts warranty, will start from the seller sales invoice.
•The serial number must appear on the sales invoice to the final
customer.
•Repair and maintenance must be carried out only by Agres,
Tecomec s.r.l. or authorized centers
As indicated in the Returning goods topic, the documentation must be correct for the
equipment analysis to begin.