Teka CGC 4G AI AL Manual

Installation and maintenance manual
COCINAS CRISTAL-GAS CG.1 4G / CG.1 3G. 1P
CG Lux-60 4G. / CG Lux-70 4G. / CG Lux-70 4G AI AL
CG Lux-70 5G. / CG Lux-60 4G. Al AL / CG Lux-70 5G. Al AL
CG Lux-70 5G AI TR AL / CG Lux-70 5G TR / CGC 4G / CGC 4G AI AL
CG Lux-75 2G AI TR AL / CG Lux-86 3G AI TR AL
CG Lux-86 2G 1P AI TR AL

Dear Customer,
Thank you for choosing a TEKA hob.
We are sure that our product will fully satisfy
your requirements.
This modern, functional and practical applian-
ce has been built using top quality materials
which are subjected to strict quality controls
throughout the manufacturing process.
Before installing or using our product, we
recommend you to carefully read this manual
and to follow its instructions step by step in
order to obtain the best possible results.
Keep this instruction manual in a safe place
so that you can consult it whenever necessary
and comply with the warranty requirements.
To benefit from our Warranty you must pre-
sent proof of purchase together with the
warranty certificate.
Safety Instructions
Before using your hob for the first time, please
read the installation and connection instruc-
tions.
These hob models can be installed in the
same kitchen units as TEKA ovens and control
panels.
N.B. To avoid the risk of burns, keep children
away from the hob during or after its opera-
tion.
We recommend you to follow our instructions
and that the installation of our hobs be carried
out by our Technical Service personnel only.
User’s Guide to this Instruction Manual
2

Introduction Page 4
Description of the Appliance 4
Installation 9
Positioning of the hobs 9
Positioning of the oven 10
Anchoring of the hob 10
Connecting the hob to the oven or
the control panel 11
Gas Connection 12
Electrical Connection 13
Gas transformation 14
Technical Information 16
Dimensions and powers 16
Technical Data 18
Rating Plates 20
Use and Maintenance 24
Special requirements before first use 24
Component Parts of Gas Burners 24
Lighting of Burners 24
Switching on Electric Hotplates 26
Components of a Safety System 27
Using your Hob 29
Hints for the correct Usage of Burners 29
Hints for the correct Usage of
Electric Hotplates 29
Reminder 30
Cleaning and Conservation 31
Electric Hotplates (Mod. CG. 1 3G 1P) 32
Maintenance 32
If Something Doesn´t Work 33
Contents
3

CG. 1 4G (see drawing 1)
1Auxiliary burner of 860 Kcal/h - 1 kW.
2Semi fast burner of 1,500 Kcal/h -
1.75 kW.
3Fast burner of 2,550 Kcal/h - 3 kW
4Semi fast burner of 1,500 Kcal/h -
1.75 kW.
• All burners incorporate a pan support.
• Maximum calorific power: 6,400 Kcal/h -
7.5 kW.
CG.1 3G. 1P. (see drawing 2)
1Auxiliary burner of 860 Kcal/h - 1 kW.
2High-power hotplate of 1,500 W,
Ø 145 mm.
3Semi fast burner of 1,500 Kcal/h -
1.75 kW.
4Fast burner of 2,550 Kcal/h - 3 kW.
• All burners incorporate a pan support.
• Maximum calorific power: 4,900 Kcal/h -
5.75 kW.
• Maximum electric power: 1,500 Watts.
Introduction
4
Description of the Appliance
12
4 3
12
3 4
Drawing 1 Drawing 2

CG-Lux-60 4G. and CG Lux-60 4G AI AL (see
drawing 3)
1Fast burner of 2,580 Kcal/h - 3 kW.
2Semi fast burner of 1,500 Kcal/h -
1.75 kW.
3Semi fast burner of 1,500 Kcal/h -
1.75 kW.
4Auxiliary burner of 860 Kcal/h - 1 kW.
5Burner controls.
• All burners incorporate a pan support.
• Maximum calorific power: 6,450 Kcal/h -
7.5 kW.
CGC 4G and CGC 4G AI AL (see drawing 4)
1Fast burner of 2,580 Kcal/h - 3 kW.
2Semi fast burner of 1,500 Kcal/h -
1.75 kW.
3Semi fast burner of 1,500 Kcal/h -
1.75 kW.
4Auxiliary burner of 860 Kcal/h - 1 kW.
• All burners incorporate a pan support.
• Maximum calorific power: 6,450 Kcal/h -
7.5 kW.
5
3
5
1
2 4
21
3 4
Drawing 3 Drawing 4

CG-Lux-70 5G., and CG Lux -70 5G AI AL (See
drawing 5)
1Fast burner of 2,580 Kcal/h - 3 kW.
2Fast burner of 2,580 Kcal/h - 3 kW.
3Semi fast burner of 1,500 Kcal/h -
1.75 kW.
4Semi fast burner of 1,500 Kcal/h -
1.75 kW.
5Auxiliary burner of 860 Kcal/h - 1 kW.
6Burner controls.
• All burners incorporate a pan support.
• Maximum calorific power: 9,020 Kcal/h -
10.5 kW.
CG-Lux-70 5G TR and CG Lux -70 5G AI TR AL
(See drawing 6)
1Fast burner of 2,580 Kcal/h - 3 kW.
2Triple ring burner of 3,000 Kcal/h -
3.5 kW.
3Semi fast burner of 1,500 Kcal/h -
1.75 kW.
4Semi fast burner of 1, 500 Kcal/h -
1.75 kW.
5Auxiliary burner of 860 Kcal/h - 1 kW.
6Burner controls.
• All burners incorporate a pan support.
• Maximum calorific power: 9,450 Kcal/h -
11 kW.
6
1 2
4
3
56
1 2
4
3
56
Drawing 5 Drawing 6

7
CG-Lux-70 4G and CG Lux -70 4G AI AL
(See drawing 7)
1Fast burner of 2,580 Kcal/h - 3 kW.
2Semi fast burner of 1,500 Kcal/h -
1.75 kW.
3Semi fast burner of 1,500 Kcal/h -
1.75 kW.
4Auxiliary burner of 860 Kcal/h - 1 kW.
5Burner controls.
• All burners incorporate a pan support.
• Maximum calorific power: 6,450 Kcal/h -
7.5 kW.
CG-Lux-75 2G AI TR AL (See drawing 8)
1Triple ring burner of 3,010 Kcal/h -
3.5 kW.
2Triple ring burner of 3,010 Kcal/h -
3.5 kW.
3Burner controls.
• All burners incorporate a pan support.
• Maximum calorific power: 6,020 Kcal/h -
7 kW.
1
2
3
45
1 2
3
Drawing 7 Drawing 8

CG-Lux-86 3G AI TR AL (See drawing 9)
1Triple ring burner of 3,010 Kcal/h -
3.5 kW.
2Triple ring burner of 3,010 Kcal/h -
3.5 kW.
3Semi fast burner of 1,500 Kcal/h -
1.75 kW.
4Burner controls.
• All burners incorporate a pan support.
• Maximum calorific power: 7,520 Kcal/h -
8.75 kW.
CG-Lux-86 2G 1P AI TR AL (See drawing 10)
1Triple ring burner of 3,010 Kcal/h -
3.5 kW.
2Triple ring burner of 3,010 Kcal/h -
3.5 kW.
3High-power hotplate of 1,500 W, Ø 145 mm.
4Burner controls.
• All burners incorporate a pan support.
• Maximum calorific power: 6,020 Kcal/h -
7 kW.
• Maximum electric power: 1,500 Watts.
8
1 3 2
4
1 3 2
4
Drawing 9 Drawing 10

INSTALLATION AND ADJUSTMENT MUST BE
CARRIED OUT BY AUTHORISED TECHNICAL
PERSONNEL ACCORDING TO THE APPLICABLE
INSTALLATION REGULATIONS.
Depending on the model to be installed an aper-
ture will be made in the worktop, of the dimen-
sions specified in the drawing 11. A template is
included in the packaging of models CG.1 4G.
and CG.1 3G. 1P. for the correct sizing of the
aperture for these two hob models.
If the hob is installed above kitchen storage
units (cupboards, drawers, etc.), an interme-
diate panel must be fitted.
For hobs with controls, its location must
include a ventilation slot at the front, of 110
cm2. In this case the minimum distance bet-
ween the lower part of the hob and the upper
part of the furniture below the hob will be 20
mm. If there is no front ventilation slot, the
minimum distance between the hob and the
upper part of the furniture must be 130
mm.The hob must be installed at least at 10
cm from its sides to any wall in the room.
The minimum vertical distance of the lower
part of the piece of furniture placed above the
hob will be 600 mm.
The piece of furniture where the hob with oven
is to be placed will be properly fixed. Mod.: CG Lux-60 y CGC 4G
Mod.: CG.1 3G. 1P. y CG.1 4G.
Mod.: CG Lux-70
Mod.: CG Lux-75
Mod.: CG Lux-86
* In the case of the granite hob the measu-
rement can be 580 mm.
Installation
9
Positioning of the hobs
A
B
C
D
E
A
B
C
D
E
Important
Drawing 11

Positioning of the oven
See the applicable manual.
Once the hob position has been dimensioned,
the seal (J) must be affixed to the lower part
of the cooker. This is fastened by means of
four clamps (G), each of which has two tabs
(P) which are inserted in the apertures (O) in
the hob until they click into place. To secure
the clamp, open the tab (S) outwards a little
as indicated in the figure. Once the seal and
the clamps have been positioned the applian-
ce may be installed in its position.
Use a screwdriver to tighten the screws (T) on
the four clamps and the hob will be perfectly
secured in place. (See drawing 12).
N.B. It is imperative to install the seal under
the brim of the worktop. Failure to install this
may cause the worktop to be exposed to high
temperatures.
In the cases of the models CG.1 4G and CG.1
3G 1P, the clamps must be fitted as shown in
the picture 13, depending on the thickness of
the furniture.
For worktops 30 mm thick or less, use the M5
screws supplied as complementary fixation by
introducing them into the circular hole of the
clamp. A fillet shall form in this hole as the
screw is introduced in it. This operation should
be done before fastening the clamps to the hob.
To install hob model CGC 4G AI AL, insert the
quick-fix nuts in the screw housings (see dra-
wing 14), connect the clip which corres
ponds with the height measurement of the
hob unit (20, 30 and 40 mm) and tighten the
screws until they are well secure.
Seal Work top Screw
Fastening clip Quick-fix nut
10
J
O
S
O
PG
TA
D E
B C
A B
CD E
20 mm. 30 mm.40 mm.
Anchoring of the hob
Self-tapping screw for
worktops of 20 and 30
mm. wide
20/30 mm.
40 mm.
Drawing 12
Drawing 13
Drawing 14

Hob models CG-Lux-75 2G and CG-Lux-86 3G
are installed in the same way as the CGC 4G
AI AL, except for the staples which are
geometrically different. The installation of
these hobs must be carried out in the way
shown in the drawing 15, depending on the
thickness of the work top.
Seal Work top Screw
Fastening clip Quick-fix nut
CGC 4G
Once the hob position has been dimensioned,
the seal must be affixed (J) to the hob.
Fix the clamps (K) into the holes on the lower
part of the case, as shown in drawing, by tighte-
ning the four screws supplied (ø4.2 mm).
The clamps (K) and seal (J) are supplied in the
packaging along with the hob. (See drawing 16).
If the unit below the hob is to be used to store
products it must be situated at a distance of at
least 10 cm below the hob. Furthermore, it must
be taken into account that the temperature in
the interior of the furniture may rise to 60oC.
CONNECTING THE HOB TO THE OVEN
(Mod. CG.1 4G, CG.1 3G 1P and CGC 4G) OR
THE CONTROL PANEL
To connect the hob to the oven, four telescopic
universal joints are provided. (See drawing 17).
To make this connection, proceed as follows:
1Disconnect from the mains supply (mod.
CG.1 3G 1P and CGC 4G AI AL).
2Detach the telescopic universal joints by
pressing the retention tab (marked PUSH)
using a thin screwdriver and extract the
extender a few centimetres.
3Remove the four lockpins from the ends (B).
4Partially insert the oven in its position, taking
care not to snag the telescopic universal
joints which are hanging from the underside
of the hob, and leave sufficient space to be
able to connect the other ends of the joints
to the rods at the rear part of the control
panel, before finally connecting the lockpins.
5For the electrical connection between the
two appliances, connect the hob connector
to the oven connector (mod. CG.1 3G 1P
and CGC 4G AI AL). 11
Drawing 16
A
D E
B C
AB
CDE
20 mm. 30 mm.40 mm.
20
J
30
40
J
J
K
K
K
A
A
B
Drawing 15
Drawing 17

Rear view of the Control Panel:
Flexible Power Cable.
Connector.
Power Unit Protective Casing.
6Position the oven in its definitive location,
ensuring that the telescopic universal
joints are well connected to the rods and
that the telescopic tubes are introduced
well aligned with each other in order to
favour their movement.
7Position the control panel on the oven’s
fascia.
8To operate, the controls must be pressed
in and then turned in order to release the
safety device.
If the telescopic universal joints are too short,
extensions can be used. These are inserted at
pressure and fastened with the corresponding
cover.
To make the oven’s electrical connection, con-
sult the oven’s instruction manual.
Hob model CGC 4G AI AL
This hob should be fitted onto the oven by
following the same method, except for item 7,
where the procedure shall be as follows:
Fix the hob knob covers on the oven according
to the oven instructions manual. Fix the knob
covers included with the hob and remove tho-
se for the oven.
This hob comes complete with knob covers for
all TEKA ovens except for models RT-600 and
RT-800. For these two models, order the knob
covers in your nearest TEKA establishment or
official technical service.
The hob’s gas connection to the mains supply
must be made in accordance with the applica-
ble installation regulations and by qualified
technical personnel (an authorized installer).
The gas connection for these hobs must be by
means of rigid piping, given that this is an
immobilized appliance, in the case of hobs
destined for the EC. The hob is prepared with
a
1/2"
diameter screw connection according to
ISO 228-1, or
1/2"
diameter conical screw con-
nection to ISO 7-1 according to the regulations
of the receiving country.
For the markets with
1/2"
ISO 228-1 connec-
tion a copper tube of diameter 10/12 mm is
suplied as an accessory. This can be welded
to the gas intake pipe.
The room must be provided with adequate ven-
tilation, in accordance with the applicable
regulations.
The gas connection between the hob and the
mains gas pipe must be in accordance with
the basic regulations for gas installations in
homes.
12
1
2
3
1
2
3
Drawing 18
Gas Connection

TEKA will not accept responsability for faults
or damage caused by incorrect or defective
instalation.
Once the gas connetion has been made the
airtightness of the installation mus be chec-
ked. If the check is made using air, the tes-
ting pressure must be no greater than 200
g/cm2 .
To avoid causing damage to the hob during
installation when tightenig the gas pipe con-
nection nut, a maximum grip torque of 350
kg.f.cm must be used.
After installing the hob, check that the bur-
ners’ minimum settings are well regulated. To
do this, light the burners and check that they
do not go out when brusquely turned from
maximum to minimum.
Do not connect the hob burners with town gas
whose composition contains carbon monoxi-
de, except in models which incorporate a
safety device.
Each time the gas connection nut is removed
the washer must be replaced.
The gas connection must be so sited that it is
not adversely heated when the appliance is in
operation.
When the gas hob has been installed, it is essen-
tial to check that neither the gas hose nor the
electric cable is in contact with hot parts of the
appliance or hot gas exhaust, otherwise heat
damage to the hose and cable could occur.
When installation is completed, check that
all the gaskets are leaktight and any other
possible leak using a soap based solution,
never a flame.
(Only for cookers with automatic ignition or
with electric hotplates).
First of all it must be checked that the mains
voltage is the same as that indicated on the
appliance’s rating plate.
The connection must be made through an
omnipolar cut-off switch with a distance of at
least 3 mm between the contacts, assuring
disconnection in cases of emergency or for
the cleaning of the hob. It must also be provi-
ded with the correct earth connection in accor-
dance with the applicable regulations.
If it comes necessary to change the flexible
power cable in model CG.1 3G. 1P, the repla-
cement must be carried out by TEKA’s official
Technical Service as special tools are requi-
red. With the other hob models it is also
recommended that the replacement be carried
out by TEKA’s Techncial Service, though these
cables can be ordered from the Technical Ser-
vice giving the reference CG Lux-60, CG Lux-
70, CG Lux-75, CG Lux-86 3G and CG Lux-86
2G 1P mains power cable, depending on the
model in question.
13
Elbow Union
Gasket
Straight
Hose Holder
Electrical Connection
Drawing 19

Important!
The transformation of the appliance to use a
different gas to that for which it has been
sold must only be carried out by a qualified
technician.
Information for the Technical Service: in the
event of conversion of the type of gas or
pressure in the appliance, the new regulation
label must be placed over the existing one, in
order to identify the new characteristics after
the changeover.
To make the transformation replace the gas
nozzles and regulate the minimum settings of
the taps.
The gas nozzles necessary for each type of
gas are indicated in table 1.
To replace the gas nozzles it is necessary to
follow the following instructions:
• Remove the pan supports and the top part
of the burners in order to access the nozzle.
• Use a no 7 tubular spanner to remove
the nozzles and replace them with the
corresponding alternative nozzles. Take care
to tighten the nozzles well so as to avoid the
risk of gas leaks.
• Reposition the pan support and burner
covers.
Once the gas nozzles have been replaced, the
following instructions must be followed to
graduate the minimum settings.
Hob CG.1 4G, CG.1 3G 1P, CGC 4G y CGC 4G
AI AL
• Remove the oven or the control panel from
their place to access the gas taps.
• Light the burners at their minimum setting.
• Use a small screw driver to remove the
screw on the right or centre of the plug of
the gas key (turn left for a big flame and
right for a small flame).
• Once the setting has been graduated
check that the flame remains at its mini-
mum setting when the control is brusquely
turned between the maximum and the
minimum setting.
14
Gas transformation
Table 1
CG LUX-60, CG LUX-70, CGC 4G, CG.1 4G, CG.1 3G. 1P.
CG Lux-75 and CG Lux-86
Burner Family
First Second Third
Group a Group c Group e Group H Group E+ Group 3+
Triple ring 290 290 290 135 135 95
Triple ring 5R (SHA) 340 340 340 - - -
Fast 260 260 260 116 116 85
Semi fast 185 185 185 97 97 65
Auxiliary 145 145 145 72 72 50
Gas nozzle diameter (Ø) expressed in 1/100 mm

• In order to access the screw which gradua-
tes the gas flow through the taps in hob
CGC 4G AI AL, remove the screws that fix
the cover protecting the taps to the case
and lift the cover.
Others hobs
• Remove the tap controls by pulling them
upwards strongly.
• Light the burners at their minimum setting.
• Use a small screw driver to remove the
screw on the right or centre of the plug of
the gas key (turn left for a big flame and
right for a small flame).
• Once the setting has been graduated
check the the flame remains at its mini-
mum setting when the control is brusquely
turned between the maximum and the
minimum setting.
Models CG LUX-75 and CG LUX-86 regulated
for town gas can not be transformed to opera-
te neither natural nor butane gas.
The only intervention necessary for the trans-
formation is the replacement of the gas nozz-
les and their setting.
TEKA INDUSTRIAL, S.A. will not accept
responsibility for incorrect hob operation if the
gas transformation and regulation of minimum
burner settings are not carried out by TEKA’s
official Technical Service.
15

16
Dimensions and powers
Models CG.1 4G CG.1 3G. 1P. CG Lux-60 CG Lux-60 CGC CGC 4G CG Lux-70
4G AI AL 4G. 4G AI AL 4G.
Dimensions in mm
Length 590 590 610 610 600 600 710
Width 510 510 510 510 510 510 510
Depth 120 120 75 75 100 100 70
Glass thickness 5 5 8 8 8 8 8
Worktop
hob
dimensions mm.
Length 570 570 580 580 580 580 690
Width 492 492 490 490 490 490 490
3.5 kW Triple
ring gas burner
3 kW
fast burner 1 1 1 1 1 1 1
1.75 kW semi
fast burner 2 1 2 2 2 2 2
1 kW
auxiliary burner 1 1 1 1 1 1 1
1,000 W electric
hotplate Ø 145 mm.
1,500 W electric
hotplate Ø 145 mm. 1
1,500 W electric
hotplate Ø 180 mm.
Electric
Maximum nominal
power W 1.500 0,6 0,6
Supply
voltage V 230 220/240 220/240
Frequency Hz 50/60 50/60 50/60
Gas
Maximum
power kW 7,5 5,75 7,5 7,5 7,5 7,5 7,5
Technical information

17
Models CG Lux-70 CG Lux-70 CG Lux-70 CG Lux-70 CG Lux-70 CG Lux-75 CG Lux-86 CG Lux-86
4G AI AL 5G. 5G AI AL 5G AI TR AL 5G. TR 2G AI TR AL 3G AI TR AL 2G 1P AI TR AL
Dimensions in mm
Length 710 710 710 710 710 750 860 860
Width 510 510 510 510 510 450 450 450
Depth 70 70 70 70 70 70 70 70
Glass thickness 8 8 8 8 8 8 8 8
Worktop
hob
dimensions mm.
Length 690 690 690 690 690 670 815 815
Width 490 490 490 490 490 350 405 405
3.5 kW Triple
ring gas burner 1 1 2 2 2
3 kW
fast burner 1 2 2 1 1
1.75 kW semi
fast burner 2 2 2 2 2 1
1 kW
auxiliary burner 1 1 1 1 1
1,000 W electric
hotplate Ø 145 mm.
1,500 W electric
hotplate Ø 145 mm. 1
1,500 W electric
hotplate Ø 180 mm.
Electric
Maximum nominal
power W 0,6 0,6 0,6 0,6 0,6 1.500
Supply
voltage V 220/240 220/240 220/240 220/240 220/240 230
Frequency Hz 50/60 50/60 50/60 50/60 50/60 50/60
Gas
Maximum
power kW 7,5 10,5 10,5 11 11 7 8,75 7

18
COMMON CHARACTERISTICS TO THE ELEC-
TRIC HOTPLATES AND AUTOMATIC LIGHTING
MODEL
The supply voltage and frequency must be
those indicated in the rating plate. The fire
protection is of “X” type. The hob must be
installed at over 15 cm away from the side walls.
(See drawing 20).
In the event of a hotplate being cracked the
hob must be switched off at the mains.
COMMON CHARACTERISTICS TO EVERY
MODEL WITH GAS BURNERS
Warnings:
a) “Before installing, make sure that the local
distribution conditions (gas type and pressure)
are compatible with the setting of the applian-
ce”.
b) “ The setting conditions, of this appliance
are printed on the label (or the rating plate)”.
c) “This appliance must not be connected to a
device for the evacuation of combustion pro-
ducts. Its installation and connection will be
carried out according the installation rules in for-
ce. Special attention will be paid to the applica-
ble specifications concerning ventilation”.
Attention: The use of a gas cooking applian-
ce, produces heat and humidity in the room
where it is installed. Good ventilation of the
kitchen must be ensured by keeping the natu-
ral ventilation holes open or by opening a win-
dow or installing an efficient mechanical venti-
lation device (mechanical ventilation hood).
Technical Data
Drawing 20
Table 2
Country Category
Spain III1ace2H3+
Portugal II2H3+
France II2E+3+
United Kingdom II2H3+
Greece I3+

COMMON CHARACTERISTICS TO EVERY
MODEL
N.B.: All the hob models referred to in this
manual have hot zones during or after their
use and can cause burns.
Care must be taken when handling these hobs
before installation as there may be rough
zones or corners which may be dangerous.
19
Burner Triple Large Standard Small
ring
Nominal calorific consumption kW 3,5 3 1,75 1
Nominal consumptions* G-130 (Nm3/h) 0,49 0,42 0,24 0,14
G-150 (Nm3/h) 0,63 0,54 0,31 0,18
G-110 (Nm3/h) 0,79 0,68 0,40 0,23
G-20 (Nm3/h) 0,33 0,29 0,17 0,10
G-25 (Nm3/h) 0,38 0,33 0,19 0,11
G-30 (Kg/h) 0,25 0,22 0,13 0,07
G-31 (Kg/h) 0,24 0,21 0,13 0,07
CCR CG Lux-60, CG Lux-70
CGC 4G, CG.1 4G and CG.1 3G. 1P kW 1,55 0,77 0,47 0,33
CCR CG Lux-75 and CG Lux-86 kW 1,55 – 0,47 –
Efficiency % >52 >52 >52 –
* On standard calorific power
Table 3

20
TEKA INDUSTRIAL, S.A.
SANTANDER - ESPAÑA
Mod. CG.1 4G
G-110 Vr Nm3/h G-20 Vr Nm3/h1.70 0.71
G-130 Vr Nm3/h G-25 Vr Nm3/h
1.05 0.83
G-150 Vr
ES FR
Nm3/h G-30 Mr Kg/h1.35 0.55
G-31 Mr Kg/h0.54
∑Qn
(P.C.S.) 7.50
Clase 3
Nº
Cat. Kat III1ace2H3+ II2E+3+
p (mbar) 8-18-28/37 20/25 28/37
GB GR PT
Cat. Kat II2H3+ I3+ II2H3+
p (mbar) 20-28/37 28/37 20-30/37
ELECT. H∆EKTPIKO
TYP. B1221300A
TEKA INDUSTRIAL, S.A.
SANTANDER - ESPAÑA
Mod. CG.1.3G.1P
G-110 Vr Nm3/h G-20 Vr Nm3/h1.30 0.55
G-130 Vr Nm3/h G-25 Vr Nm3/h0.80 0.64
G-150 Vr
ES FR
Nm3/h G-30 Mr Kg/h1.03 0.42
G-31 Mr Kg/h0.41
∑Qn
(P.C.S.) 5.75
Clase 3
Nº
Cat. Kat III1ace2H3+ II2E+3+
p (mbar) 8-18-28/37 20/25 28/37
GB GR PT
Cat. Kat II2H3+ I3+ II2H3+
p (mbar) 20-28/37 28/37 20-30/37
ELECT. H∆EKTPIKO
TYP. B1D21300A
220…230 V ~
50/60 Hz. 1.500 W
TEKA INDUSTRIAL, S.A.
SANTANDER - ESPAÑA
Mod. CG LUX 60 4G
G-110 Vr Nm3/h G-20 Vr Nm3/h1.70 0.71
G-130 Vr Nm3/h G-25 Vr Nm3/h
1.05 0.83
G-150 Vr
ES FR
Nm3/h G-30 Mr Kg/h1.35 0.55
G-31 Mr Kg/h0.54
∑Qn
(P.C.S.) 7.50
Clase 3
Nº
Cat. Kat III1ace2H3+ II2E+3+
p (mbar) 8-18-28/37 20/25 28/37
GB GR PT
Cat. Kat II2H3+ I3+ II2H3+
p (mbar) 20-28/37 28/37 20-30/37
ELECT. H∆EKTPIKO
TYP. A1322100A
TEKA INDUSTRIAL, S.A.
SANTANDER - ESPAÑA
Mod. CG LUX 70 4G
G-110 Vr Nm3/h G-20 Vr Nm3/h1.70 0.71
G-130 Vr Nm3/h G-25 Vr Nm3/h1.05 0.83
G-150 Vr
ES FR
Nm3/h G-30 Mr Kg/h1.35 0.55
G-31 Mr Kg/h0.54
∑Qn
(P.C.S.) 7.50
Clase 3
Nº
Cat. Kat III1ace2H3+ II2E+3+
p (mbar) 8-18-28/37 20/25 28/37
GB GR PT
Cat. Kat II2H3+ I3+ II2H3+
p (mbar) 20-28/37 28/37 20-30/37
ELECT. H∆EKTPIKO
TYP. A1322100A
0099
0099 0099
0099