Teka BKSSL BPM Setup guide

THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF TEKA ILLUMINATION AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR SELL ANYTHING IT MAY
DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF TEKA ILLUMINATION IS STRICTLY FORBIDDEN.
THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF TEKA ILLUMINATION AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR SELL ANYTHING IT MAY
DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF TEKA ILLUMINATION IS STRICTLY FORBIDDEN.
Warning Hot Surface
NEEDED
FOR
INSTALLATION:
By Others
Wear Gloves
DATE
5-14-18
REFERENCE NUMBER
INS-2569-00
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX [phone]
www.tekaillumination.com • [email protected]
High Voltage
5/64” & 1/8” Allen Wrench
Waterproof Wire Connectors
Gloves
Cap
Shade
Base
Lens
Rings
Spacers
IMPORTANT - WEAR GLOVES TO AVOID GETTING FINGERPRINTS ON THIS PRODUCT. MANY TEKA ILLUMINATION PRODUCTS ARE DESIGNED TO NATURALLY PATINA.
OILS FROM YOUR SKIN WILL ACCELERATE THIS PROCESS WHERE TOUCHED AND ARE NEARLY IMPOSSIBLE TO REMOVE. THIS PROCESS OCCURS OVER TIME AND IS
DETERMINED BY THE INSTALLATION ENVIRONMENT.
· Suitable for wet locations
IMPORTANT LISTINGS AND CERTIFICATIONS
IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE THESE INSTALLATION INSTRUCTIONS
• Product must be installed by a qualified person in a manner
consistent with its intended use and in compliance with the
National Electrical Code, Canadian Electrical Code, and all Local and
Provincial Codes.
• Follow product label information and instructions.
• Qualified Personnel with appropriate personal protective
equipment must perform all servicing of this product.
• Before wiring to power supply and during servicing, turn off and
lock out power at fuse or circuit breaker before service.
• The use of accessory equipment not recommended by the
manufacturer or installed contrary to instructions may cause an
unsafe condition. The use of damaged components may cause an
unsafe condition and void product warranty.
IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE ALL SAFETY
AND INSTALLATION INSTRUCTIONS
• Do not block light emanating from product in whole or part, as
this may cause an unsafe condition.
• Never operate the fixture with missing or damaged lens.
Lens must be cleaned on regular basis.
• Entire fixture may become extremely hot. Do not touch hot
lens or fixture body.
• Replace LED assembly only with correct wattage and type of
power supply appropriate for LED assembly.
• All gaskets, o-rings and sealing surfaces must be kept clean
during installation and service; failure to do this may cause an
unsafe condition and void product warranty.
INSTRUCTIONS PERTAINING TO
A RISK OF FIRE, OR INJURY TO
PERSONS IMPORTANT SAFETY
INSTRUCTIONS
Lighted fixture is HOT!
WARNING - To reduce the risk of
FIRE OR INJURY TO PERSONS:
Turn off/unplug and allow to cool before replacing LED.
Fixture gets HOT quickly! Contact only switch/plug when
turning on. Do not touch hot lens, guard, or enclosure.
Keep fixture away from materials that may burn.
Do not operate the luminaire fitting with a missing or
damaged shield. Do not touch the source at any time. Use
a soft cloth or gloves. Oil from skin may cause damage.
SAVE THESE INSTRUCTIONS
BEACON POLE MOUNT™ (BPM)
IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE THESE INSTALLATION INSTRUCTIONS
Pole Top Installation Instructions
Solid State BPM
(Beacon Pole Mount)
3-1/2” O.D. Pole or Pole with
3-1/2” O.D Tenon
(Specify Separately)
(Pole By Others)

Phase 2 - Fixture Installation (Pole Top Option)
Pole Top Installation Instructions
IMPORTANT SAFETY INFORMATION LISTED ON REVERSE
READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS
DATE
5-14-18
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX [phone]
www.tekaillumination.com • [email protected]
REFERENCE NUMBER
INS-2569-00
BEACON POLE MOUNT™ (BPM)
2. Make watertight connections from primary
branch circuit to driver leads using waterproof
wire connectors (By Others). Connect green
ground wire to ground wiring from driver.
Connect incoming dimming controls to driver
primary side dimming controls. Secondary side
is connected via quick disconnect. See wiring
diagram.
WIRING DIAGRAM
1. Pull primary branch circuit wiring up to driver
bracket location at top of pole. Pull incoming
dimming controls to top of pole. Feed through
strain relief.
LINE
Red
FIXTURE
COM
Driver
Black
GROUND
DIM +
DIM -
GROUND IN HOUSING
LINE
Red
FIXTURE
COM
Driver
Black
DIM +
DIM -
GROUND ON PLATE
LINE
Red
FIXTURE
COM
Driver
Black
DIM +
DIM -
3. Place connections and driver on bracket into
pole. Rest bracket on pole top or tenon.
Phase 1 - Install Pole
1. Install 3-1/2” O.D. pole (By Others) or pole with
3-1/2” O.D. tenon (By Others, Specify Separately)
according to lighting plan and manufacturer’s
installation instructions. Install conduit (By
Others) to be used with this product.
2. Pull primary branch circuit wiring necessary for
installation (By Others). Pull incoming dimming
controls necessary for installation. (By Others).
Leave sufficient wire length in the pole for
future service.
4. Slide fixture over pole top. Secure with four (4)
1/4-20 screws using /1/8” Allen wrench. Make
sure the fixture is completely seated. Do not
overtighten.
4. Make secondary connections via quick disconnect
from driver secondary side to fixture secondary
side.

THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF TEKA ILLUMINATION AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR SELL ANYTHING IT MAY
DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF TEKA ILLUMINATION IS STRICTLY FORBIDDEN.
THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF TEKA ILLUMINATION AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR SELL ANYTHING IT MAY
DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF TEKA ILLUMINATION IS STRICTLY FORBIDDEN.
Warning Hot Surface
NEEDED
FOR
INSTALLATION:
By Others
Wear Gloves
DATE
5-14-18
REFERENCE NUMBER
INS-2569-01
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX [phone]
www.tekaillumination.com • [email protected]
High Voltage
5/64” & 1/8” Allen Wrench
Waterproof Wire Connectors
Gloves
Adjustable Crescent Wrench
Cap
Shade
Base
Lens
Rings
Spacers
IMPORTANT - WEAR GLOVES TO AVOID GETTING FINGERPRINTS ON THIS PRODUCT. MANY TEKA ILLUMINATION PRODUCTS ARE DESIGNED TO NATURALLY PATINA.
OILS FROM YOUR SKIN WILL ACCELERATE THIS PROCESS WHERE TOUCHED AND ARE NEARLY IMPOSSIBLE TO REMOVE. THIS PROCESS OCCURS OVER TIME AND IS
DETERMINED BY THE INSTALLATION ENVIRONMENT.
· Suitable for wet locations
IMPORTANT LISTINGS AND CERTIFICATIONS
IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE THESE INSTALLATION INSTRUCTIONS
• Product must be installed by a qualified person in a manner
consistent with its intended use and in compliance with the
National Electrical Code, Canadian Electrical Code, and all Local and
Provincial Codes.
• Follow product label information and instructions.
• Qualified Personnel with appropriate personal protective
equipment must perform all servicing of this product.
• Before wiring to power supply and during servicing, turn off and
lock out power at fuse or circuit breaker before service.
• The use of accessory equipment not recommended by the
manufacturer or installed contrary to instructions may cause an
unsafe condition. The use of damaged components may cause an
unsafe condition and void product warranty.
IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE ALL SAFETY
AND INSTALLATION INSTRUCTIONS
• Do not block light emanating from product in whole or part, as
this may cause an unsafe condition.
• Never operate the fixture with missing or damaged lens.
Lens must be cleaned on regular basis.
• Entire fixture may become extremely hot. Do not touch hot
lens or fixture body.
• Replace LED assembly only with correct wattage and type of
power supply appropriate for LED assembly.
• All gaskets, o-rings and sealing surfaces must be kept clean
during installation and service; failure to do this may cause an
unsafe condition and void product warranty.
INSTRUCTIONS PERTAINING TO
A RISK OF FIRE, OR INJURY TO
PERSONS IMPORTANT SAFETY
INSTRUCTIONS
Lighted fixture is HOT!
WARNING - To reduce the risk of
FIRE OR INJURY TO PERSONS:
Turn off/unplug and allow to cool before replacing LED.
Fixture gets HOT quickly! Contact only switch/plug when
turning on. Do not touch hot lens, guard, or enclosure.
Keep fixture away from materials that may burn.
Do not operate the luminaire fitting with a missing or
damaged shield. Do not touch the source at any time. Use
a soft cloth or gloves. Oil from skin may cause damage.
SAVE THESE INSTRUCTIONS
BEACON POLE MOUNT™ (BPM)
IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE THESE INSTALLATION INSTRUCTIONS
3-1/2” O.D. Hinge Base Pole or
Hinge Base Pole with 3-1/2” O.D
Tenon (Specify Separately)
(Pole By Others)
Hinge Base Installation Instructions
Solid State BPM
(Beacon Pole Mount)

IMPORTANT SAFETY INFORMATION LISTED ON REVERSE
READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS
DATE
5-14-18
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX [phone]
www.tekaillumination.com • [email protected]
REFERENCE NUMBER
INS-2569-01
BEACON POLE MOUNT™ (BPM)
Hinge Base Installation Instructions
Phase 1 - Install Pole
1. Install 3-1/2” O.D. pole (By Others) or pole with
3-1/2” O.D. tenon (By Others, Specify Separately)
according to lighting plan and manufacturer’s
installation instructions. Install conduit (By Others)
to be used with this product.
2. Pull primary branch circuit wiring necessary for
installation (By Others). Pull incoming dimming
controls necessary for installation. (By Others).
Leave sufficient wire length in the pole for
future service.
3. Make watertight connections from primary
branch circuit to driver leads using waterproof
wire connectors (By Others). Connect green
ground wire to ground wiring from driver.
Connect incoming dimming controls to driver
primary side dimming controls. Connect
secondary side of driver to wiring for fixture
leads. See wiring diagram.
WIRING DIAGRAM
Phase 2 - Fixture Installation (Hinge Base Option)
LINE
Red
FIXTURE
COM
Driver
Black
GROUND
DIM +
DIM -
GROUND IN HOUSING
LINE
Red
FIXTURE
COM
Driver
Black
DIM +
DIM -
GROUND ON PLATE
LINE
Red
FIXTURE
COM
Driver
Black
DIM +
DIM -
2. Hinge pole open for access to conduit and
branch circuit wiring. Pull branch circuit wiring
and dimming controls to splice location.
1. Remove base cover (if required). Open hinge base
on pole by loosening three (3) 1/2”-13 stainless
steel bolts using adjustable crescent wrench.
4. Place driver, bracket and connections into pole.
Hinge pole back to upright position. Connect
secondary wiring to secondary side of driver.
Pull secondary wiring to top of pole. Length of
secondary wiring will vary with height of pole.
Leave length for future service.
5. Close hinge pole, then secure to base with
three (3) 1/2” I.D. flat washers, split lock
washers and three (3) 1/2”-13 stainless steel
bolts using an adjustable crescent wrench.
6. If pole comes with cover, place cover on base
of pole. Secure with four (4) 1/4”-20 hex screws
using 3/16” Allen wrench.

IMPORTANT SAFETY INFORMATION LISTED ON REVERSE
READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS
DATE
5-14-18
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX [phone]
www.tekaillumination.com • [email protected]
REFERENCE NUMBER
INS-2569-01
BEACON POLE MOUNT™ (BPM)
Hinge Base Installation Instructions
7. Make watertight connections using waterproof
wire connectors to connect fixture leads to
secondary leads from driver. Leave length for
future service. See wiring diagram.
8. Slide fixture over pole top. Secure with four (4)
1/4-20 screws using /1/8” Allen wrench. Make
sure the fixture is completely seated. Do not
overtighten.

THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF TEKA ILLUMINATION AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR SELL ANYTHING IT MAY
DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF TEKA ILLUMINATION IS STRICTLY FORBIDDEN.
THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF TEKA ILLUMINATION AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR SELL ANYTHING IT MAY
DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF TEKA ILLUMINATION IS STRICTLY FORBIDDEN.
Warning Hot Surface
NEEDED
FOR
INSTALLATION:
By Others
Wear Gloves
DATE
5-14-18
REFERENCE NUMBER
INS-2569-02
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX [phone]
www.tekaillumination.com • [email protected]
High Voltage
5/64”, 1/8”, 5/32” & 1/16” Allen Wrench
Waterproof Wire Connectors
Gloves
Cap
Shade
Base
Lens
Rings
Spacers
IMPORTANT - WEAR GLOVES TO AVOID GETTING FINGERPRINTS ON THIS PRODUCT. MANY TEKA ILLUMINATION PRODUCTS ARE DESIGNED TO NATURALLY PATINA.
OILS FROM YOUR SKIN WILL ACCELERATE THIS PROCESS WHERE TOUCHED AND ARE NEARLY IMPOSSIBLE TO REMOVE. THIS PROCESS OCCURS OVER TIME AND IS
DETERMINED BY THE INSTALLATION ENVIRONMENT.
· Suitable for wet locations
IMPORTANT LISTINGS AND CERTIFICATIONS
IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE THESE INSTALLATION INSTRUCTIONS
• Product must be installed by a qualified person in a manner
consistent with its intended use and in compliance with the
National Electrical Code, Canadian Electrical Code, and all Local and
Provincial Codes.
• Follow product label information and instructions.
• Qualified Personnel with appropriate personal protective
equipment must perform all servicing of this product.
• Before wiring to power supply and during servicing, turn off and
lock out power at fuse or circuit breaker before service.
• The use of accessory equipment not recommended by the
manufacturer or installed contrary to instructions may cause an
unsafe condition. The use of damaged components may cause an
unsafe condition and void product warranty.
IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE ALL SAFETY
AND INSTALLATION INSTRUCTIONS
• Do not block light emanating from product in whole or part, as
this may cause an unsafe condition.
• Never operate the fixture with missing or damaged lens.
Lens must be cleaned on regular basis.
• Entire fixture may become extremely hot. Do not touch hot
lens or fixture body.
• Replace LED assembly only with correct wattage and type of
power supply appropriate for LED assembly.
• All gaskets, o-rings and sealing surfaces must be kept clean
during installation and service; failure to do this may cause an
unsafe condition and void product warranty.
INSTRUCTIONS PERTAINING TO
A RISK OF FIRE, OR INJURY TO
PERSONS IMPORTANT SAFETY
INSTRUCTIONS
Lighted fixture is HOT!
WARNING - To reduce the risk of
FIRE OR INJURY TO PERSONS:
Turn off/unplug and allow to cool before replacing LED.
Fixture gets HOT quickly! Contact only switch/plug when
turning on. Do not touch hot lens, guard, or enclosure.
Keep fixture away from materials that may burn.
Do not operate the luminaire fitting with a missing or
damaged shield. Do not touch the source at any time. Use
a soft cloth or gloves. Oil from skin may cause damage.
SAVE THESE INSTRUCTIONS
BEACON POLE MOUNT™ (BPM)
IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE THESE INSTALLATION INSTRUCTIONS
3-1/2” O.D. Pole or Pole with
3-1/2” O.D Tenon with Hand
Hole (Specify Separately)
(Pole By Others)
Hand Hole Installation Instructions
Solid State BPM
(Beacon Pole Mount)

IMPORTANT SAFETY INFORMATION LISTED ON REVERSE
READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS
DATE
5-14-18
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX [phone]
www.tekaillumination.com • [email protected]
REFERENCE NUMBER
INS-2569-02
BEACON POLE MOUNT™ (BPM)
WIRING DIAGRAM
Phase 1 - Install Pole
1. Install pole (By Others) with 3”x5” min. hand hole
according to lighting plan and manufacturer’s
installation instructions. Install conduit (By
Others) to be used with this product.
2. Pull wiring necessary for installation (By Others.)
Leave sufficient wire length in the pole for
future service.
Phase 2 - Fixture Installation (Hand Hole Option)
3. Open hand hole as per pole manufacturer’s
instructions, then pull primary branch circuit
wiring through conduit to splice location and
pull down fixture leads from installed pole top.
1. Thread fixture leads down pole to splice location
at hand hole.
2. Slide fixture over pole top. Secure with four (4)
1/4”-20 set screws using 3/16” Allen wrench.
Make sure the fixture is completely seated. Do not
overtighten.
Hand Hole Installation Instructions
4. Make watertight connections from primary
branch circuit to driver leads using waterproof
wire connectors (By Others). Connect green
ground wire to ground wiring from driver.
Connect incoming dimming controls to driver
primary side dimming controls. Connect
secondary side of driver to fixture leads. See
wiring diagram.
LINE
Red
FIXTURE
COM
Driver
Black
GROUND
DIM +
DIM -
GROUND IN HOUSING
LINE
Red
FIXTURE
COM
Driver
Black
DIM +
DIM -
GROUND ON PLATE
LINE
Red
FIXTURE
COM
Driver
Black
DIM +
DIM -
5. Place connections and driver on bracket into
pole through hand hole. (For use with 3”x5” hand
hole).
7. Close hand hole cover with hardware and tools
as per pole manufacturer. (Pole and Hardware
By Others)
6. Driver bracket should hang off small horizontal
interior bar inside pole near hand hole. Use two
hooks on bracket to hang on interior bar.

IMPORTANT SAFETY INFORMATION LISTED ON REVERSE
READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS
DATE
5-14-18
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX [phone]
www.tekaillumination.com • [email protected]
REFERENCE NUMBER
INS-2569-03
BEACON POLE MOUNT™ (BPM)
3. Detach heatsink from fixture body via quick
disconnect. Carefully pull away and turn upside
down to access LED.
Do not pull on connector or wiring. Handle
with care.
1. Loosen three (3) captive #10-24 screws on cap
with 5/32” Allen wrench.
5. Loosen two (2) #4-40 screws with 1/16” Allen
wrench.
4. Loosen three (3) #6-32 set screws on side of
dome lens optic holder using 1/16” Allen wrench.
Gently remove dome lens and optic holder.
6. Carefully remove LED module from heatsink.
Do not pull on connector or wiring. Handle
with care.
Fragile! Do not pull on connector or wiring.
Handle with care.
7. Use small pick tool to push connector off LED
board through two small slots behind connector.
Once loose, lift connector upwards and off board.
NEEDED
FOR
INSTALLATION:
By Others
5/32”, 3/32” & 1/16” Allen Wrench
Waterproof Wire Connectors
Gloves
2. Loosen three (3) #4-40 screws with 3/32” Allen
wrench that hold heatsink to fixture body.
8. Spread thin, even layer of thermal paste on back
of new LED module. Place new LED module onto
heatsink, lining up module with holes for screws.
Tighten two (2) #4-40 screws using 1/16” Allen
wrench to secure LED module to heatsink.
9. Press connector straight downwards into slot
on module to snap into place.
Connector will only fit in one direction.
Replacing Optic and LED Module
LED Replacement Installation Instructions

IMPORTANT SAFETY INFORMATION LISTED ON REVERSE
READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS
DATE
5-14-18
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX [phone]
www.tekaillumination.com • [email protected]
REFERENCE NUMBER
INS-2569-03
BEACON POLE MOUNT™ (BPM)
11. Attach heatsink to fixture body via quick
disconnect. Line up on spacers.
13. Attach cap with securing three (3) #10-24
screws using 5/32” Allen wrench.
10. Place dome lens into optic holder. Tighten three
(3) #6-32 set screws on side of dome lens optic
holder using 1/16” Allen wrench.
Relamping Instructions
12. Tighten three (3) #4-40 screws with 3/32” Allen
wrench to secure heatsink to fixture body.