TEKTELIC Communications Kona Macro Gateway User manual

TEKTELIC COMMUNICATIONS INC.
Document type:
User Guide
Document number:
T0005158_UG
Document version:
0.6
Document Status:
Approved
Product name:
Kona Macro Gateway
Product codes:
See Table 1
TEKTELIC Communications Inc.
7657 10th Street NE
Calgary, AB, Canada T2E 8X2
Phone: [phone]
© 2019 TEKTELIC Communications Inc., All rights reserved.
All products, names and services are trademarks and registered trademarks of their respective companies.
Disclaimer:
Material contained in this document is subject to change without notice. The material herein is solely for
information purposes and does not represent a commitment by TEKTELIC or its representatives. TEKTELIC has
prepared the information contained in this document solely for use by its employees, agents, and customers.
Dissemination of this information and/or concepts to other parties is prohibited without the prior written consent
of TEKTELIC. In no event will TEKTELIC be liable for any incidental or consequential damage in connection with the
furnishing, performance or use of this material.
TEKTELIC reserves the right to revise this publication in accordance with formal change control procedures defined
by TEKTELIC.

Kona Macro User Guide T0005158_UG Version 0.6
TEKTELIC Communications Inc. Confidential Page 2 of 32
Revision History
Version
Date
Status
Editor
Comments
0.2
Jan. 11, 2018
Draft
S. Morrison
First release
0.3
Feb, 01, 2018
Draft
S. Morrison
Added language translation
0.31
Feb. 13, 2018
Draft
T. Danshin
Updated Table 1 and Table 4 to only
reference North American models
0.32
Feb. 13, 2018
Draft
T. Danshin
Updated product descriptions in Table 1 and
4
0.33
Feb 14, 2018
Approved
T. Danshin
Updated MPE information
0.34
Feb 14, 2018
Approved
T. Danshin
Updated Radio Compliance Statements
0.4
Feb 15, 2018
Approved
S. Morrison
Restore Table 1 and Table 4 to show all
certified models. Removed Section 3.
0.5
Apr 24, 2019
Approved
Z. Herasymiuk
Added North American 2 variant products to
T-Code Table
Added Pt 27 FCC to Regulatory Table
0.6
Jul 30, 2019
Approved
Z. Herasymiuk
Added Proposition 65 Statements

Kona Macro User Guide T0005158_UG Version 0.6
TEKTELIC Communications Inc. Confidential Page 3 of 32
Table of Contents
1Product Description................................................................................................................. 5
1.1 Overview .......................................................................................................................... 5
1.2 Physical Interfaces............................................................................................................ 7
1.3 Specifications.................................................................................................................... 9
2Installation............................................................................................................................. 10
2.1 Safety Precautions.......................................................................................................... 10
2.2 Unpacking and Inspection.............................................................................................. 11
2.3 Required Equipment for Installation.............................................................................. 11
2.4 Kona Macro Gateway Mounting.................................................................................... 11
2.5 Ground Cable Installation .............................................................................................. 14
2.6 Direct DC Power Cable Installation ................................................................................ 15
2.7 RF Cable Installation....................................................................................................... 16
2.8 Copper Ethernet Cable Installation................................................................................ 16
2.9 Proposition 65 Statement .............................................................................................. 16
3Radio Compliance Statements .............................................................................................. 17
4Description du produit........................................................................................................... 18
4.1 aperçu............................................................................................................................. 18
4.2 Interfaces physiques ...................................................................................................... 20
4.3 Spécifications.................................................................................................................. 22
5Installation............................................................................................................................. 24
5.1 Précautions de sécurité.................................................................................................. 24
5.2 Déballage et inspection.................................................................................................. 25
5.3 Équipement pour l'installation....................................................................................... 25
5.4 Montage de la passerelle Kona Macro........................................................................... 25
5.5 Installation du câble de masse....................................................................................... 28
5.6 Installation directe du câble d'alimentation CC............................................................. 29
5.7 Installation du câble RF .................................................................................................. 30
5.8 Installation du câble Ethernet en cuivre........................................................................ 30

Kona Macro User Guide T0005158_UG Version 0.6
TEKTELIC Communications Inc. Confidential Page 4 of 32
6déclarations de conformité radio.......................................................................................... 31

Kona Macro User Guide T0005158_UG Version 0.6
TEKTELIC Communications Inc. Confidential Page 5 of 32
1Product Description
1.1 Overview
The Kona Macro Gateway is an outdoor hardened LoRaWAN IoT gateway that supports the full
range of LoRa WAN channels. The Gateway supports one external LoRa antenna, an internal GPS
antenna, two power options including direct DC input power or Power over Ethernet (PoE), and
two backhaul options including copper Ethernet or 3G/4G wireless. Table 1 presents the currently
available Kona Macro Gateway models.
Table 1: Kona Macro Gateway Models
Product Code
Modem
Geolocation
Region
Mode
T0005129
LTE
Yes
North America
FDD
T0005130
LTE
No
Europe
TDD
T0005131
LTE
Yes
Europe
TDD
T0005169
LTE
No
China
470 FDD
T0005179
LTE
Yes
China
470 FDD
T0005180
LTE
No
China
780 TDD
T0005181
LTE
Yes
China
780 TDD
T0005182
LTE
No
Japan
TDD
T0005183
LTE
Yes
Japan
TDD
T0005184
LTE
No
Singapore
TDD
T0005185
LTE
Yes
Singapore
TDD
T0005186
LTE
No
Australia
TDD
T0005187
LTE
Yes
Australia
TDD
T0005247
No
No
North America
FDD
T0005248
No
Yes
North America
FDD
T0005249
No
No
Europe
TDD
T0005250
No
Yes
Europe
TDD
T0005251
No
No
China
470 FDD
T0005252
No
Yes
China
470 FDD
T0005253
No
No
China
780 TDD
T0005254
No
Yes
China
780 TDD
T0005255
No
No
Japan
TDD
T0005256
No
Yes
Japan
TDD
T0005257
No
No
Singapore
TDD
T0005258
No
Yes
Singapore
TDD
T0005259
No
No
Australia
TDD
T0005260
No
Yes
Australia
TDD

Kona Macro User Guide T0005158_UG Version 0.6
TEKTELIC Communications Inc. Confidential Page 6 of 32
T0005261
No
No
New Zealand
TDD
T0005262
No
Yes
New Zealand
TDD
T0005263
LTE
No
New Zealand
TDD
T0005264
LTE
Yes
New Zealand
TDD
T0005265
No
No
BCIL
TDD
T0005266
No
Yes
BCIL
TDD
T0005267
LTE
No
BCIL
TDD
T0005268
LTE
Yes
BCIL
TDD
T0005269
No
No
Taiwan
TDD
T0005270
No
Yes
Taiwan
TDD
T0005271
LTE
No
Taiwan
TDD
T0005272
LTE
Yes
Taiwan
TDD
T0005273
No
No
Australia 2
FDD
T0005274
No
Yes
Australia 2
FDD
T0005275
LTE
No
Australia 2
FDD
T0005276
LTE
Yes
Australia 2
FDD
T0005277
No
No
Australia 2
TDD
T0005278
No
Yes
Australia 2
TDD
T0005279
LTE
No
Australia 2
TDD
T0005280
LTE
Yes
Australia 2
TDD
T0006031
No
No
North America 2
FDD
T0006032
No
Yes
North America 2
FDD
T0006033
LTE
No
North America 2
FDD
T0006034
LTE
Yes
North America 2
FDD
Figure 1 illustrates the Kona Macro Gateway external form-factor with the front view on the left
and rear view on the right. All models share the same mechanical form-factor.

Kona Macro User Guide T0005158_UG Version 0.6
TEKTELIC Communications Inc. Confidential Page 7 of 32
Figure 1: Kona Macro Gateway Common Dimensions
1.2 Physical Interfaces
Figure 2 illustrates the bulkhead layout for the Kona Macro Gateway. All models share the same
bulkhead layout.

Kona Macro User Guide T0005158_UG Version 0.6
TEKTELIC Communications Inc. Confidential Page 8 of 32
Figure 2: Kona Macro Gateway Bulkhead Layout
All Kona Gateway module interconnect is located on the bottom facing bulkhead. The RF
connectors are water proof while un-mated but all other connectors must be terminated with
mating connectors or covered with the supplied protective cap when not in use in order to be
water tight. Connector types and their mating connectors are listed in Table 2.
Table 2: Kona Macro Gateway Interface Connector Types
Interface
Connector Type
Mating Connector
LoRa Antenna
Ports
N-Type female
Industry standard N-Type male
DC Power
2 pin CPC
Protective
Earth
Ground
LoRa RF
Antenna
Copper
Ethernet
3G/4G Modem
SIM card
access port

Kona Macro User Guide T0005158_UG Version 0.6
TEKTELIC Communications Inc. Confidential Page 9 of 32
3G/4G Modem
SIM card
SIM card
Industry standard, located behind SIM card access
port cover
Copper Ethernet
Port
Threaded, circular, RJ-45
Shenzhen Chogori Technology Co., Ltd. approved
mating connector (p/n 33000111-02 or equivalent)
Direct DC Power
Input Port
Threaded, circular, 2
contact DC power
Shenzhen Chogori Technology Co., Ltd. approved
mating connector (p/n 23002211-02, or equivalent)
Earth Ground
Chassis Protective Earth
Ground terminal
Industry standard 2-hole lug, 1/4 x 0.75” spacing
1.3 Specifications
The Kona Macro Gateway specifications are listed in Table 3.
Table 3: Kona Macro Gateway Specifications
Attribute
Specification
Dimensions
222.2mm (8.7”) wide x 101mm (4.0”) deep x 287.3mm (11.3”) tall
Weight
5.1 kg (11.3 lbs)
Operating Temperature
-40°C to 60°C (-40°F to 140°F) at sea level Including solar loading.
Relative Humidity
10% to 100%
Operating Altitude
-60 m to 4,000 m (-197 ft to 13,123 ft)
Power Input, Direct DC
48 VDC nominal, 37 to 57 VDC operating range.
Positive or negative ground referenced feed. SELV source required.
5A recommended input overcurrent protection (2A minimum to 10A
maximum allowed).
Power Input, PoE
802.3 at (Type 2 Class 4), Mode A or Mode B or 4-pair Mode.
Power Consumption
20 W maximum
Weather Tightness
UL Type 6 (IP-67)
Regulatory Compliance
CSA/UL 60950-1 & CSA/UL 60950-22, CE IEC 60950-1
FCC Pt. 15, RSS-247, EN 301 489-1
FCC Pt. 27 (North American 2 Variant Only)
Surge Protection
All interfaces are protected to primary levels.

Kona Macro User Guide T0005158_UG Version 0.6
TEKTELIC Communications Inc. Confidential Page 10 of 32
2Installation
2.1 Safety Precautions
•The Kona Macro Gateway must be installed in a restricted access location (such that touching
of the Gateway by non-service persons is not likely).
•The Kona Macro Gateway may become hot to the touch during normal operation at elevated
ambient temperatures.
•The Kona Macro Gateway has no internal field serviceable parts. The Gateway module must
only be opened by an approved TEKTELIC service center.
•All installation practices must be in accordance with the local and national electrical codes.
•Do not work on the system during periods of lightning activity.
•The Kona Macro Gateway is considered permanently connected equipment. The Protective
Earth Ground connection (that is, the two-hole lug to chassis ground) is always required.
•Ensure the Kona Macro Gateway Protective Earth Ground connection is properly terminated
prior to the connection of any other interface.
•The Kona Macro Gateway contains primary lightning surge suppression on the Direct DC
power port, the Copper Ethernet port, and the LoRa RF antenna port. The primary lightning
protectors have the ability to bridge the interface to chassis isolation boundary during over-
voltages. Ensure that the Protective Earth Ground connection is always in place.
•Ensure that the Kona Macro Gateway is secured to eliminate any physical hazard to people
or property. The Gateway must be securely mounted according to the mounting instructions
prior to any cable connection and operation.
•The Kona Macro Gateway does not contain a power disconnection device; a readily accessible
disconnection device must be incorporated external to the Kona Macro Gateway.
•The direct DC powered Kona Macro Gateway shall be supplied through an input overcurrent
protection device rated not more than 10 A. The overcurrent protection must have the
appropriate current interrupt capacity for the power source and must be incorporated into
the non-earthed conductor(s) of the Kona Macro Gateway DC supply.
•For the direct DC power input, the DC positive pin must be at positive potential relative to
the DC negative pin. If the polarity is reversed, the unit will not sustain damage but will not
operate until the connection polarity is corrected.

Kona Macro User Guide T0005158_UG Version 0.6
TEKTELIC Communications Inc. Confidential Page 11 of 32
•Although the Kona Macro Gateway can be powered through either the direct DC input or the
power over Ethernet (PoE) input, simultaneous application of power to both inputs may result
in unexpected operation and shall be avoided.
•The Kona Macro Gateway power source must meet SELV requirements.
•Always ensure the 3G/4G Modem SIM card access port is properly sealed after installing a
SIM card.
2.2 Unpacking and Inspection
The following should be considered during the unpacking of a new Kona Macro Gateway.
1. Inspect the shipping carton and report any significant damage to TEKTELIC.
2. Unpacking should be conducted in a clean and dry location when possible.
3. Do not discard the shipping box or foam inserts as they will be required if a unit is returned
for repair or re-configuration.
2.3 Required Equipment for Installation
The following tools are required to install the Kona Macro Gateway module:
1. A 6 point metric socket set and torque wrench drive.
2. Anti-oxidant compound (NO-OX-ID, Penetrox, Noalox, Ox-Gard or equivalent).
3. A small wire brush.
4. A clean cloth.
5. Weatherproofing tape kit for the RF connector (Scotch Wireless Weatherproofing Kit, WK-
101 recommended).
6. Appropriately sized pipe clamps for pole mounting or appropriate screws or bolts (four
sized M8) with any required anchors according to the wall construction for wall mounting.
2.4 Kona Macro Gateway Mounting
Kona Macro Gateway is designed to be mounted to a vertical pole or wall using the supplied
mounting bracket which attaches at the four screw locations on the back of the module
illustrated in Figure 3.

Kona Macro User Guide T0005158_UG Version 0.6
TEKTELIC Communications Inc. Confidential Page 12 of 32
Figure 3: Kona Macro Gateway Mounting Bracket Attachment Screw Locations
The mounting bracket is a single part that bolts to the back surface of the Gateway using supplied
hardware (four M6x1.0 - 14 mm bolts with flat and star lock washers) as illustrated in Figure 4.
The Gateway module must be oriented with the connector bulkhead facing down, towards earth.
Mounting
screw location
Mounting
screw location
Mounting
screw location
Mounting
screw location

Kona Macro User Guide T0005158_UG Version 0.6
TEKTELIC Communications Inc. Confidential Page 13 of 32
Figure 4: Kona Macro Gateway Module with Mounting Bracket
Ensure that the structure to which the Gateway is being mounted is secure and able to support
a dead load of at least 136 kg (300 lbs). The area below must be free of any obstructions to cable
ingress.
The Kona Macro Gateway wall mounting procedure is as follows:
1. Bolt the wall mounting bracket to the Gateway module using the supplied bolts and
washers.
2. Install 2 site supplied M8 bolts into the wall at 139.7 mm (5.5”) center spacing, leaving
the bold heads protruding with a 2mm gap from the wall surface.
3. Hang the Kona Macro Gateway with bracket from the two bolts by inserting the keyhole
slots at the top of the bracket onto the 2 bolts and tightening the bolts.
4. Insert and tighten two additional site supplied M8 bolts through the holes at the bottom
of the bracket.
The Kona Macro Gateway pole mounting procedure is as follows:
Mounting
Bracket

Kona Macro User Guide T0005158_UG Version 0.6
TEKTELIC Communications Inc. Confidential Page 14 of 32
1. Bolt the wall mounting bracket to the Gateway module using the supplied bolts and
washers.
2. While temporarily supporting the Gateway with bracket, install the two site supplied pipe
clamps, one through each of the upper and lower slotted clamp mounting points.
2.5 Ground Cable Installation
The Kona Macro Gateway is considered Permanently Connected Equipment and requires a
permanently connected Protective Earth Ground (PEG) conductor. The Protective Earth Ground
connection is made through a 1/4 x 0.75” on center double hole lug to the ground termination
point illustrated in Figure 5. The recommended ground cable gauge is #10 AWG.
The Kona Macro Gateway grounding system shall follow local and national electrical codes. The
Protective Earth Ground conductor terminated at the double hole lug point is mandatory and
must be the first connection made to the Kona Macro Gateway during installation. Proper routing
and termination of this cable is key to robust lightning withstand performance; in high
susceptibility installations, every effort shall be made to minimize connection inductance and
ground bed resistance.
The ground cable installation steps are as follows:
1. Lightly abrade the surface of the casting ground area with a fine wire brush to remove the
oxide layer.
2. Use a clean cloth to remove any debris from this surface.
3. Immediately coat the contact surface with a thin layer of anti-oxidant compound.
4. Install the ground cable through its 2-hole lug onto the chassis ground point using the two
supplied 1/4 - 20 x 1/2” bolts with flat and star lock washers, torqued to 10.4 Nm (92
in·lbs).

Kona Macro User Guide T0005158_UG Version 0.6
TEKTELIC Communications Inc. Confidential Page 15 of 32
Figure 5: Chassis Ground Connection
2.6 Direct DC Power Cable Installation
The Kona Macro Gateway direct DC feed terminates at a dedicated two pin circular plastic
connector (CPC) on the bulkhead. The direct DC power input is isolated from chassis (earth) with
the exception of the primary surge suppressors. One lead of the DC power feed is normally earth
referenced external to the Kona Macro Gateway (usually at the power source by convention).
The DC power cable shall be rated for outdoor application according to local and national
electrical codes.
The CPC direct DC connector shall be as specified in Table 2 and shall follow the signal polarity
identified in Figure 6.
Chassis Ground
Connection

Kona Macro User Guide T0005158_UG Version 0.6
TEKTELIC Communications Inc. Confidential Page 16 of 32
Figure 6: Direct DC Power CPC Connector Connection Polarity
2.7 RF Cable Installation
The Kona Macro Gateway installation requires connection to a LoRa RF antenna. The RF cable
attaches to the N-Type connector located on the bulkhead of the Gateway. Torque the connector
to 1.7 to 2.3 Nm (15 to 20 in·lbs). The N-Type connector interface to a cable is not water proof
and must be taped to be used outdoors. TEKTELIC recommends taping with Scotch Wireless
Weatherproofing Kit, WK-101. Follow the taping procedures outlined by the supplier of this tape
system.
Note that the 3G/4G modem antenna is internal to the Kona Macro Gateway.
2.8 Copper Ethernet Cable Installation
The Kona Macro Gateway Ethernet port may be used on a temporary basis for commissioning
and maintenance or may be permanently connected for backhaul. When the port is not in use,
the weatherproof protective cap must be installed. When the port is permanently connector for
backhaul, the proper water-tight mating connector specified in Table 2 must be used.
The Ethernet cable must have minimum 24 AWG conductors and shall be rated for outdoor
application according to local and national electrical codes.
2.9 Proposition 65 Statement
󱣻󱣼󱣽WARNING: This product can expose you to chemicals including lead, beryllium & nickel,
which is known to the State of California to cause cancer, birth defects or other reproductive
harm. For more information, go to www.P65Warnings.ca.gov.
Black
DC Negative
White
DC Positive
Keyed DC Power
Connector (CPC)
DC Positive
DC Negative

Kona Macro User Guide T0005158_UG Version 0.6
TEKTELIC Communications Inc. Confidential Page 17 of 32
3Radio Compliance Statements
Federal Communications Commission
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to
operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of
the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help.
To comply with FCC/IC RF exposure limits for general population / uncontrolled exposure, the antennas used for this
transmitter must be installed to provide a separation distance of at least 30 cm from all persons and must not be co-
located or operating in conjunction with any other antenna or transmitter. This product must be installed by professional
trained RF technicians.
Industry Canada
This Device complies with Industry Canada License-exempt RSS standard(s). Operation is subject to the following two
conditions:
1. This device may not cause interference, and
2. This device must accept any interference, including interference that may cause undesired operation of the device.
This radio transmitter 22504-T0005158 has been approved by Industry Canada to operate with the antenna types listed
below with the maximum permissible gain indicated. Antenna types not included in this list, having a gain greater than the
maximum gain indicated for that type, are strictly prohibited for use with this device.
The required antenna impedance is 50 ohms.
Only omnidirectional type antennas with maximum gain of 8dBi can be used for the LoRa radios of this product if the cable
insertion loss at 900 MHz is 0.5dB or more for 1 carrier operation at 28.5dBm or 2dB or more for 2 carrier operation at 30dBm
total. Antenna(s) shall be installed to location providing a separation distance of at least 13.8 inches (35 cm) from any human
body.
During product operation, always keep a separation distance of at least 13.8 inches (35 cm) from any connected antenna(s).
Before servicing the product, the antenna(s) or cables, turn off the transmission function or the unit power if you have to get
closer than the minimum separation distance. This product must be installed by professional trained RF technicians.

Kona Macro User Guide T0005158_UG Version 0.6
TEKTELIC Communications Inc. Confidential Page 18 of 32
4Description du produit
4.1 aperçu
La passerelle Kona Macro Gateway est une passerelle LoRaWAN IoT durcie à l'extérieur qui prend
en charge la gamme complète des canaux LoRa WAN. La passerelle prend en charge une antenne
LoRa externe, une antenne GPS interne, deux options d'alimentation, y compris une alimentation
CC directe ou Power over Ethernet (PoE), et deux options backhaul, y compris Ethernet cuivre ou
3G / 4G sans fil. Le tableau 4 présente les modèles Kona Macro Gateway actuellement disponibles
pour le marché nord-américain..
Table 4: Modèles de Kona Macro
Code de produit
Modem
Géolocalisation
Région
Mode
T0005129
LTE
Yes
North America
FDD
T0005130
LTE
No
Europe
TDD
T0005131
LTE
Yes
Europe
TDD
T0005169
LTE
No
China
470 FDD
T0005179
LTE
Yes
China
470 FDD
T0005180
LTE
No
China
780 TDD
T0005181
LTE
Yes
China
780 TDD
T0005182
LTE
No
Japan
TDD
T0005183
LTE
Yes
Japan
TDD
T0005184
LTE
No
Singapore
TDD
T0005185
LTE
Yes
Singapore
TDD
T0005186
LTE
No
Australia
TDD
T0005187
LTE
Yes
Australia
TDD
T0005247
No
No
North America
FDD
T0005248
No
Yes
North America
FDD
T0005249
No
No
Europe
TDD
T0005250
No
Yes
Europe
TDD
T0005251
No
No
China
470 FDD
T0005252
No
Yes
China
470 FDD
T0005253
No
No
China
780 TDD
T0005254
No
Yes
China
780 TDD
T0005255
No
No
Japan
TDD
T0005256
No
Yes
Japan
TDD
T0005257
No
No
Singapore
TDD
T0005258
No
Yes
Singapore
TDD
T0005259
No
No
Australia
TDD

Kona Macro User Guide T0005158_UG Version 0.6
TEKTELIC Communications Inc. Confidential Page 19 of 32
T0005260
No
Yes
Australia
TDD
T0005261
No
No
New Zealand
TDD
T0005262
No
Yes
New Zealand
TDD
T0005263
LTE
No
New Zealand
TDD
T0005264
LTE
Yes
New Zealand
TDD
T0005265
No
No
BCIL
TDD
T0005266
No
Yes
BCIL
TDD
T0005267
LTE
No
BCIL
TDD
T0005268
LTE
Yes
BCIL
TDD
T0005269
No
No
Taiwan
TDD
T0005270
No
Yes
Taiwan
TDD
T0005271
LTE
No
Taiwan
TDD
T0005272
LTE
Yes
Taiwan
TDD
T0005273
No
No
Australia 2
FDD
T0005274
No
Yes
Australia 2
FDD
T0005275
LTE
No
Australia 2
FDD
T0005276
LTE
Yes
Australia 2
FDD
T0005277
No
No
Australia 2
TDD
T0005278
No
Yes
Australia 2
TDD
T0005279
LTE
No
Australia 2
TDD
T0005280
LTE
Yes
Australia 2
TDD
T0006031
No
No
North America 2
FDD
T0006032
No
Yes
North America 2
FDD
T0006033
LTE
No
North America 2
FDD
T0006034
LTE
Yes
North America 2
FDD
Figure 7 illustre le facteur de forme externe Kona Macro Gateway avec la vue de face sur la
gauche et la vue arrière sur la droite. Tous les modèles partagent le même facteur de forme
mécanique.

Kona Macro User Guide T0005158_UG Version 0.6
TEKTELIC Communications Inc. Confidential Page 20 of 32
Figure 7: Kona Macro Gateway Dimensions communes
4.2 Interfaces physiques
Figure 8 illustre la disposition de la cloison de la Kona Macro Gateway. Tous les modèles
partagent la même disposition de cloison.