Tektronix AFG1000 Series User manual

xx
AFG1000 Series
Arbitrary Function Generator
ZZZ
Programmer Manual
*P077112901*
077-1129-01

AFG1000 Series
Arbitrary Function
Generator
ZZZ Programmer Manual
xx
Revision A
www.tek.com
077-1129-01

Copyright © Tektronix. All rights reserved. Licensed software products are owned by Tektronix or its subsidiaries
or suppliers, and are protected by national copyright laws and international treaty provisions.
Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication
supersedes that in all previously published material. Specifications and price change privileges reserved.
TEKTRONIX and TEK are registered trademarks of Tektronix, Inc.
Contacting Tektronix
Tektronix, Inc.
14150 SW Karl Braun Drive
P.O. Box 500
Beaverton, OR 97077
USA
For product information, sales, service, and technical support:
In North America, call 1-800-833-9200.
Worldwide, visit www.tek.com to find contacts in your area.

Warranty
Tektronix warrants that the product will be free from defects in materials and workmanship for a period of three (3)
years from the date of original purchase from an authorized Tektronix distributor. If the product proves defective
during this warranty period, Tektronix, at its option, either will repair the defective product without charge for parts
and labor, or will provide a replacement in exchange for the defective product. Parts, modules and replacement
products used by Tektronix for warranty work may be new or
reconditioned to like new performance. All replaced
parts, modules and products become the property of Tektronix.
In order to obtain service under this warranty, Customer must notify Tektronix of the defect before the expiration
of the warranty period and make suitable arrangements for the performance of service. Customer shall be
responsible for packaging and shipping the defective product to the service center designated by Tektronix,
shipping charges prepaid, and with a copy of customer proof of purchase. Tektronix shall pay for the return of the
product to Customer if the shipment is to a location within the country in which the Tektronix service center is
located. Customer shall be responsible for paying all shipping charges, duties, taxes, and any other charges for
products returned to any other locations.
This warranty shall not apply to any defect, failure or damage caused by improper use or improper or inadequate
maintenance and care. Tektronix shall not be obligated to furnish service under this warranty a) to repair damage
resulting from attempts by personnel other than Tektronix representatives to install, repair or service the product;
b) to repair damage resulting from improper use or connection to incompatible equipment; c) to repair any damage
or malfunction caused by the use of non-Tektronix supplies; or d) to service a product that has been modified or
integrated with other products when the effect of such modification or integration increases the time or difficulty of
servicing the product.
THIS WARRANTY IS GIVEN BY TEKTRONIX WITH RESPECT TO THE PRODUCT IN LIEU OF ANY
OTHER WARRANTIES, EXPRESS OR IMPLIED. TEKTRONIX AND ITS VENDORS DISCLAIM ANY
IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
TEKTRONIX' RESPONSIBILITY TO REPAIR OR REPLACE DEFECTIVE PRODUCTS IS THE SOLE AND
EXCLUSIVE REMEDY PROVIDED TO THE CUSTOMER FOR BREACH OF THIS WARRANTY.
TEKTRONIX AND ITS VENDORS WILL NOT BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL,
OR CONSEQUENTIAL DAMAGES IRRESPECTIVE OF WHETHER TEKTRONIX OR THE VENDOR HAS
ADVANCE NOTICE OF THE POSSIBILITY OF SUCH DAMAGES.
[W2 – 15AUG04]

i
AFG1000 Series Arbitrary Function Generator Programmer Manual
Table of contents
Getting Started ....................................................................................................................................... 1
Introduction...................................................................................................................................... 1
Connecting the Interface..........................................................................................................................1
Using TekVISA .......................................................................................................................................1
Where to find more information..............................................................................................................2
Syntax and Commands........................................................................................................................... 3
Command Syntax............................................................................................................................. 3
Backus-Naur Form Definition .................................................................................................................3
Command and Query Structure ...............................................................................................................3
SCPI Commands and Queries .................................................................................................................5
IEEE 488.2 Common Commands............................................................................................................9
Command Groups ......................................................................................................................... 10
Command Descriptions................................................................................................................. 14
AFGControl:CSCopy (No Query Form) ...............................................................................................14
*CLS (No Query Form).........................................................................................................................14
*IDN? (Query Only)..............................................................................................................................15
MMEMory:CATalog? (Query Only).....................................................................................................15
MMEMory:CDIRectory .........................................................................................................................16
MMEMory:DELete (No Query Form)....................................................................................................17
*OPT? (Query Only) .............................................................................................................................17
OUTPut[1|2]:IMPedance ........................................................................................................................18
OUTPut[1|2][:STATe] ............................................................................................................................18
*RCL (No Query Form)..........................................................................................................................19
*RST (No Query Form) ..........................................................................................................................20
*SAV (No Query Form)..........................................................................................................................20
[SOURce[1|2]]:AM[:DEPTh] ................................................................................................................21
[SOURce[1|2]]:AM:INTernal:FREQuency ............................................................................................21
[SOURce[1|2]]:AM:INTernal:FUNCtion ...............................................................................................22
[SOURce[1|2]]:AM:INTernal:FUNCtion:EFILe....................................................................................23
[SOURce[1|2]]:AM:SOURce .................................................................................................................24
[SOURce[1|2]]:AM:STATe ...................................................................................................................24
[SOURce[1|2]]:ASKey[:AMPLitude] ...................................................................................................25
[SOURce[1|2]]:ASKey:INTernal:RATE ................................................................................................26
[SOURce[1|2]]:ASKey:SOURce............................................................................................................27
[SOURce[1|2]]:ASKey:STATe ..............................................................................................................27
[SOURce[1|2]]:BURSt:MODE .............................................................................................................28
[SOURce[1|2]]:BURSt:NCYCles..........................................................................................................28
[SOURce[1|2]]:BURSt:SOURce ............................................................................................................29
[SOURce[1|2]]:BURSt:STATe...............................................................................................................30

Table of Contents
ii
AFG1000 Series Arbitrary Function Generator Programmer Manual
[SOURce[1|2]]:FM[:DEViation]............................................................................................................ 30
[SOURce[1|2]]:FM:INTernal:FREQuency............................................................................................. 31
[SOURce[1|2]]:FM:INTernal:FUNCtion ............................................................................................... 32
[SOURce[1|2]]:FM:INTernal:FUNCtion:EFILe .................................................................................... 33
[SOURce[1|2]]:FM:SOURce................................................................................................................ 33
[SOURce[1|2]]:FM:STATe .................................................................................................................. 34
[SOURce[1|2]]:FREQuency:CENTer................................................................................................... 35
[SOURce[1|2]]:FREQuency:CONCurrent ........................................................................................... 35
[SOURce[1|2]]:FREQuency[:CW|:FIXed]........................................................................................... 36
[SOURce[1|2]]:FREQuency:MODE .................................................................................................... 37
[SOURce[1|2]]:FREQuency:SPAN...................................................................................................... 38
[SOURce[1|2]]:FREQuency:STARt..................................................................................................... 39
[SOURce[1|2]]:FREQuency:STOP ...................................................................................................... 39
[SOURce[1|2]]:FSKey[:FREQuency] .................................................................................................. 40
[SOURce[1|2]]:FSKey:INTernal:RATE............................................................................................... 41
[SOURce[1|2]]:FSKey:SOURce........................................................................................................... 42
[SOURce[1|2]]:FSKey:STATe .............................................................................................................. 42
[SOURce[1|2]]:FUNCtion:EFILe......................................................................................................... 43
[SOURce[1|2]]:FUNCtion[:SHAPe] .................................................................................................... 43
[SOURce[1|2]]:PHASe[:ADJust] ......................................................................................................... 45
[SOURce[1|2]]:PHASe:INITiate (No Query Form) ............................................................................. 46
[SOURce[1|2]]:PM[:DEViation] .......................................................................................................... 46
[SOURce[1|2]]:PM:INTernal:FREQuency ........................................................................................... 47
[SOURce[1|2]]:PM:INTernal:FUNCtion .............................................................................................. 48
[SOURce[1|2]]:PM:INTernal:FUNCtion:EFILe................................................................................... 49
[SOURce[1|2]]:PM:SOURce................................................................................................................ 49
[SOURce[1|2]]:PM:STATe ................................................................................................................... 50
[SOURce[1|2]]:PSKey[:DEViation]...................................................................................................... 51
[SOURce[1|2]]:PSKey:INTernal:RATE................................................................................................ 51
[SOURce[1|2]]:PSKey:SOURce............................................................................................................ 52
[SOURce[1|2]]:PSKey:STATe.............................................................................................................. 53
[SOURce[1|2]]:PULSe:DCYCle ........................................................................................................... 53
[SOURce[1|2]]:PWM:INTernal:FREQuency......................................................................................... 54
[SOURce[1|2]]:PWM:INTernal:FUNCtion............................................................................................ 55
[SOURce[1|2]]:PWM:INTernal:FUNCtion:EFILe................................................................................. 56
[SOURce[1|2]]:PWM:SOURce ............................................................................................................. 56
[SOURce[1|2]]:PWM:STATe................................................................................................................ 57
[SOURce[1|2]]:PWM[:DEViation]:DCYCle........................................................................................ 58
[SOURce[1|2]]:SWEep:SOURce.......................................................................................................... 59
[SOURce[1|2]]:SWEep:SPACing ......................................................................................................... 59
[SOURce[1|2]]:SWEep:TIME .............................................................................................................. 60
[SOURce[1|2]]:VOLTage[:LEVel][:IMMediate]:OFFSet..................................................................... 61

AFG1000 Series Arbitrary Function Generator Programmer Manual
iii
Table of Contents
[SOURce[1|2]]:VOLTage[:LEVel][:IMMediate][:AMPLitude]............................................................61
SYSTem:ERRor[:NEXT]? (Query Only) ...............................................................................................62
TRACe|DATA:CATalog? (Query Only)................................................................................................63
TRACe|DATA:COPY (No Query Form) ...............................................................................................63
TRACe|DATA[:DATA]..........................................................................................................................64
TRACe|DATA[:DATA]:VALue .............................................................................................................64
TRACe|DATA:POINts ..........................................................................................................................65
*TRG (No Query Form) .........................................................................................................................66
*WAI (No Query Form) ........................................................................................................................66
Command Errors.................................................................................................................................. 67
Index .................................................................................................................................................... 68

AFG1000 Series Arbitrary Function Generator Programmer Manual
1
Getting Started
Introduction
This programmer guide provides information to use commands for remotely
controlling your instrument. With this information, write computer programs that will
perform functions such as setting the front-panel controls, selecting clock source,
setting sampling rate, and exporting data for use in other programs.
Connecting the Interface
The AFG1000 Series has a USB (type B) connector on the rear panel, as shown
in the following figure. This connector conforms to USB-TMC. Attach a USB
cable to this connector.
AC line
connector
USB (type B)
connector
Figure 1: USB (type B) connector
Using TekVISA
TekVISA is Tektronix implementation of VISA (Virtual Instrument Software
Architecture), an industry-standard communication protocol. VISA provides
a common standard for software developers so that software from multiple
vendors, such as instrument drivers, can run on the same platform. TekVISA is
industry-compliant software, available with selected Tektronix instruments.
Use this software to write (or draw) interoperable instrument drivers in a
variety of Application Development Environments (ADEs). It implements a
subset of Version 2.2 of the VISA specification for controlling USB
instrument interface locally.

2
AFG1000 Series Arbitrary Function Generator Programmer Manual
Getting Started
Installation Use an internet browser to access the Tektronix Web site
(www.tek.com/downloads)
and download the current TekVISA to your PC.
Unzip the downloaded file in a
temporary directory of your choice and run
Setup.exe.
NOTE: The details on TekVISA concepts and operations are explained in the
TekVISA Programmer Manual that can be also found on the Tektronix Web site.
Where to find more information
The following table lists related documentation available for your instrument.
The documentation is available on the Product Documentation CD and on the
Tektronix Web site (www.tek.com/manuals).
Item
Purpose
Location
Important
safety and
compliance
instructions
Compliance and
safety instructions
Built-in Help
UI Help and Operation
Quick Start
User
Manual
Unpacking, Installation,
T
utorials, Operation,
and
Overviews
Programmer
Manu
al
Menu Structures, User
Interface,
and
Programming
Information
Technical
Reference
Specifications and
performance
ver
ification procedures

AFG1000 Series Arbitrary Function Generator Programmer Manual
3
Syntax and Commands
Command Syntax
Control the operations and functions of the instrument through the USB
interface using commands and queries. The related topics listed below
describe
the syntax of these commands and queries. The topics also describe the
conventions that the instrument uses to process them. See Command Groups
(See page 10.) for a listing of the commands by command group, or use the
index to locate a specific command.
Backus-Naur Form Definition
This manual describes commands and queries using the Backus-Naur Form
(BNF) notation. The following table defines the standard BNF symbols.
Table 1: BNF symbols and meanings
Symbol Meaning
< > Defined element
:=
Is defined as
| Exclusive OR
{ } Group; one element is required
[ ] Optional; can be omitted
. . . Previous element(s) may be repeated
( ) Comment
Command and Query Structure
Overview Commands consist of set commands and query commands (usually simply called
commands and queries). Commands change instrument settings or perform a
specific action. Queries cause the instrument to return data and information about
its status.
Most commands have both a set form and a query form. The query form of the
command is the same as the set form except that it ends with a question mark.
For example, the set command MMEMory:CDIRectory has a query form
MMEMory:CDIRectory?. Not all commands have both a set and a query form;
some commands are set only and some are query only.
Messages A command message is a command or query name, followed by any
information the instrument needs to execute the command or query. Command
messages consist of five element types.

4
AFG1000 Series Arbitrary Function Generator Programmer Manual
Command Syntax
Table 2: Command message elements
Symbol Meaning
<Header> The basic command name. If the header ends with a question mark, the
command is a query. The header may begin with a colon (:) character; if
the command is concatenated with other commands the beginning
colon
is required. The beginning colon can never be used with command
headers beginning with a star (*).
<Mnemonic> A header subfunction. Some command headers have only one mnemonic.
If a command header has multiple mnemonics, they are always separated
from each other by a colon (:) character.
<Argument> A quantity, quality, restriction, or limit associated with the header. Not
all commands have an argument, while other commands have multiple
arguments. Arguments are separated from the header by a <Space>.
Arguments are separated from each other by a <Comma>.
<Comma> A single comma between arguments of multiple-argument commands. It
may optionally have white space characters before and after the comma.
<Space> A white space character between command header and argument. It may
optionally consist of multiple white space characters.
Commands Commands cause the instrument to perform a specific function or change one of
its settings. Commands have the structure:
[:]<Header>[<Space><Argument>[<Comma><Argument>]...]
A command header is made up of one or more mnemonics arranged in a
hierarchical or tree structure. The first mnemonic is the base or root of the tree and
each subsequent mnemonic is a level or branch of the previous one. Commands at
a higher level in the tree may affect those at a lower level. The leading colon (:)
always returns you to the base of the command tree.
Queries Queries cause the instrument to return information about its status or settings.
Queries have the structure:
[:]<Header>?
[:]<Header>?[<Space><Argument>[<Comma><Argument>]...]
Specify a query at any level within the command tree unless otherwise noted.
These branch queries return information about all the mnemonics
below the
specified branch or level.
Query Responses When a query is sent to the instrument, only the values are returned. When the
returned value is a mnemonic, it is noted in abbreviated format.

AFG1000 Series Arbitrary Function Generator Programmer Manual
5
Command Syntax
Command Entry Follow these general rules when entering commands:
Enter commands in upper or lower case.
Precede any command with white space characters. White space
characters
include any combination of the ASCII control characters 00 through
09 and
0B through 20 hexadecimal (0 through 9 and 11 through 32 decimal).
The instrument ignores commands that consists of just a combination of white
space characters and line feeds.
SCPI Commands and Queries
The instrument uses a command language based on the SCPI standard. The SCPI
(Standard Commands for Programmable Instruments) standard was created by a
consortium to provide guidelines for remote programming of instruments.
These guidelines provide a consistent programming environment for instrument
control and data transfer. This environment uses defined programming messages,
instrument responses and data formats that operate across all SCPI instruments,
regardless of manufacturer.
The SCPI language is based on a hierarchical or tree structure. The top level of
the tree is the root
node; it is followed by one or more lower-level nodes.
Create commands and queries from these subsystem hierarchy trees.
Commands
specify actions for the instrument to perform. Queries return
measurement data
and information about parameter settings.
Creating Commands SCPI commands are created by stringing together the nodes of a subsystem
hierarchy and separating each node by a colon.
To create a SCPI command, start with the root
node and move down the tree
structure adding nodes until you reach the
end of a branch. Most commands and
some queries have parameters; you must
include a value for these parameters. If
you specify a parameter value that is out
of range, the parameter will be set to a
default value. The command descriptions,
list the valid values for all
parameters.
Creating Queries To create a query, start at the root node of a tree structure, move down to the end of
a branch, and add a question mark.
Query Responses The query causes the instrument to return information about its status or settings.
When a query is sent to the instrument, only the values are returned. When the
returned value is a mnemonic, it is noted in abbreviated format.
Parameter Types Every parameter in the command and query descriptions is of a specified type.
(See Table 3.) The parameters are enclosed in brackets, such as <value>.

6
AFG1000 Series Arbitrary Function Generator Programmer Manual
Command Syntax
The parameter type is listed after the parameter and is enclosed in parentheses,
for example, (boolean). Some parameter types are defined specifically for the
instrument command set and some are defined by SCPI.
Table 3: Parameter types used in syntax descriptions
Parameter type
Description
Example
arbitrary block 1
A specified length of
arbitrary
data
#512234xxxxx . . . where
5
indicates that the following
5
digits (12234) specify the
length
of the data in bytes;
xxxxx
... indicates the data or
#0xxxxx...<LF><&EOI>
boolean
Boolean numbers or values
ON or ≠0
OFF or 0
discrete
A list of specific values
MIN, MAX
binary
Binary numbers
#B0110
octal
Octal numbers
#Q57, #Q3
hexadecimal 2
Hexadecimal numbers
(0-9, A, B, C, D, E, F)
#H AA, #H1
NR1
2
numeric
Integers
0, 1, 15, -1
NR2
2 3
numeric
Decimal numbers
1.2, 3.141516, -6.5
NR3
2
numeric
Floating point numbers
3.1415E-9, -16.1E5
NRf 2 numeric
Flexible decimal number that
may be type NR1, NR2 or NR3
See NR1, NR2, and NR3
examples
string 4
Alphanumeric characters (must
be within quotation marks)
"Testing 1, 2, 3"
1 Defined in ANSI/IEEE 488.2 as "Definite Length Arbitrary Block Response Data."
2 An ANSI/IEEE 488.2-1992-defined parameter type.
3 Some commands and queries will accept an octal or hexadecimal value even though the parameter type is
defined as NR1.
4 Defined in ANSI/IEEE 488.2 as "String Response Data."
Special Characters The Line Feed (LF) character or the New Line (NL) character (ASCII 10), and all
characters in the range of ASCII 127-255 are defined as special characters. These
characters are used in arbitrary block arguments only; using these characters in
other parts of any command yields unpredictable results.

AFG1000 Series Arbitrary Function Generator Programmer Manual
7
Command Syntax
Abbreviating Commands,
Queries, and Parameters
Abbreviate most SCPI commands, queries, and parameters to an accepted short
form. This manual shows these short forms as a combination of upper and
lower
case letters. The upper case letters indicate the accepted short form of a
command. As shown in the following figure, create a short form by using only
the upper case letters. The accepted short form and the long form are
equivalent
and request the same action of the instrument.
Figure 2: Example of abbreviating a command
NOTE: The numeric suffix of a command or query may be included in either the
long form or short form; the instrument will default to "1" if no suffix is used.
Chaining Commands and
Queries
Chain several commands or queries together into a single message. To create a
chained message, first create a command or query, add a semicolon (;), and then
add more commands or queries and semicolons until the message is complete.
If the command following a semicolon is a root node, precede it with a colon
(:).The single chained message should end in a
command or query, not a
semicolon. Responses to any queries in your message
are separated by
semicolons.
If a command or query has the same root and lower-level nodes as the previous
command or query, you can omit these nodes.
Unit and SI Prefix If the decimal numeric argument refers to amplitude, frequency, or time, express
it using SI units instead of using the scaled explicit point input value
format
<NR3>. (SI units are units that conform to the Systeme International
d'Unites
standard.) For example, use the input format 200 mV or 1.0 MHz
instead of
200.0E-3 or 1.0E+6, respectively, to specify voltage or frequency.

8
AFG1000 Series Arbitrary Function Generator Programmer Manual
Command Syntax
The following table lists the available units.
Table 4: Available units
Symbol Meaning
DEG degree (phase)
Hz hertz (frequency)
PCT percent (%)
s
second (time)
V volt
Vpp volt
You can omit a unit in a command, but you must include the unit when using a SI
prefix. For example, frequency of 15 MHz can be described as follows
15.0E6, 1.5E7Hz, 15000000, 15000000Hz, 15MHz, etc.
("15M" is not allowed.)
General rules for using
SCPI commands
Here are three general rules for using SCPI commands, queries, and parameters:
Use single (‘ ’) or double (“ ”) quotation marks for quoted strings, but
you cannot
use both types of quotation marks for the same string.
correct "This string uses quotation marks correctly."
correct
‘This string also uses quotation marks correctly.'
incorrect
"This string does not use quotation marks correctly.'
Use upper case, lower case, or a mixture of both cases for all
commands, queries,
and parameters.
SOURCE1:FREQUENCY 10MHZ
is the same as
and
source1:frequency 100mhz
SOURCE1:frequency 10MHZ
NOTE: Literal strings (quoted) are case sensitive, for example, file names.
No embedded spaces are allowed between or within nodes.
correct
SOURCE1:FREQUENCY 10MHZ
incorrect SOURCE1: FREQUENCY 10MHZ

AFG1000 Series Arbitrary Function Generator Programmer Manual
9
Command Syntax
IEEE 488.2 Common Commands
Description
ANSI/IEEE Standard 488.2 defines the codes, formats, protocols, and usage of
common commands and queries used on the interface between the controller and
the instruments. The instrument complies with this standard.
Command and Query
Structure
The syntax for an IEEE 488.2 common command is an asterisk (*) followed by a
command and, optionally, a space and parameter value. The syntax for an IEEE
488.2 common query is an asterisk (*) followed by a query and a question mark.
All of the common commands and queries are listed in the last part of the Syntax
and Commands section. The following are examples of common commands:
*CLS
The following are examples of common queries
*IDN?

10
AFG1000 Series Arbitrary Function Generator Programmer Manual
Command Groups
This section lists the commands organized by functional group. The Command
Descriptions section lists all commands alphabetically. (See page 14.)
Memory Commands Memory commands let you change setup memory attributes. The following table
lists and describes Memory commands.
Table 5: Memory commands
Command Description
*RCL Recall instrument setting from setup memory
*SAV Save instrument setting to setup memory
Mass Memory Commands Mass Memory commands let you change mass
memory attributes. The
following table lists and describes the Mass Memory commands.
Table 6: Mass Memory commands
Command Description
MMEMory:CATalog? Query the status of mass memory
MMEMory:CDIRectory Set/query current directory
MMEMory:DELete Delete file or directory in mass memory
Output Commands Output commands let you set output attributes. The following
table lists and
describes the Output commands.
Table 7: Output commands
Command Description
OUTPut[1|2]:IMPedance Set/query impedance
OUTPut[1|2][:STATe] Set/query output on or off

AFG1000 Series Arbitrary Function Generator Programmer Manual
11
Command Groups
Source Commands Source commands let you set waveform output parameters.
The following table
lists and describes the Source commands.
Table 8: Source commands
Command Description
[SOURce[1|2]]:AM[:DEPTh] Set/query amplitude modulation depth
[SOURce[1|2]]:AM:INTernal:FREQuency Set/query internal modulation frequency
[SOURce[1|2]]:AM:INTernal:FUNCtion Set/query internal modulation waveform
[SOURce[1|2]]:AM:INTernal:FUNCtion:EFILe Set/query EFILe setting
[SOURce[1|2]]:AM:SOURce Set/query amplitude modulation source
[SOURce[1|2]]:AM:STATe Set/query amplitude modulation status
[SOURce[1|2]]:ASKey[:AMPLitude] Set/query ASK depth
[SOURce[1|2]]:ASKey:INTernal:RATE Set/query ASK internal modulation rate
[SOURce[1|2]]:ASKey:SOURce Set/query ASK source
[SOURce[1|2]]:ASKey:STATe Set/query ASK status
[SOURce[1|2]]:BURSt:MODE Set/query burst mode
[SOURce[1|2]]:BURSt:NCYCles Set/query burst mode waveform output cycle
[SOURce[1|2]]:BURSt:SOURce Set/query burst mode trigger source
[SOURce[1|2]]:BURSt:STATe Set/query burst mode status
[SOURce[1|2]]:FM[:DEViation] Set/query frequency deviation
[SOURce[1|2]]:FM:INTernal:FREQuency Set/query internal modulation frequency
[SOURce[1|2]]:FM:INTernal:FUNCtion Set/query internal modulation waveform
[SOURce[1|2]]:FM:INTernal:FUNCtion:EFILe Set/query EFILe setting
[SOURce[1|2]]:FM:SOURce Set/query frequency modulation source
[SOURce[1|2]]:FM:STATe Set/query frequency modulation status
[SOURce[1|2]]:FREQuency:CENTer Set/query center frequency
[SOURce[1|2]]:FREQuency:CONCurrent Set/query concurrent change of frequency
[SOURce[1|2]]:FREQuency[:CW|:FIXed] Set/query output waveform frequency
[SOURce[1|2]]:FREQuency:MODE Set/query sweep status
[SOURce[1|2]]:FREQuency:SPAN Set/query sweep frequency span
[SOURce[1|2]]:FREQuency:STARt Set/query sweep start frequency
[SOURce[1|2]]:FREQuency:STOP Set/query sweep stop frequency
[SOURce[1|2]]:FSKey[:FREQuency] Set/query FSK hop frequency
[SOURce[1|2]]:FSKey:INTernal:RATE Set/query FSK internal modulation rate
[SOURce[1|2]]:FSKey:SOURce Set/query FSK source
[SOURce[1|2]]:FSKey:STATe Set/query FSK status
[SOURce[1|2]]:FUNCtion:EFILe Set/query EFILe name
[SOURce[1|2]]:FUNCtion[:SHAPe] Set/query output waveform
[SOURce[1|2]]:PHASe[:ADJust] Set/query output waveform phase
[SOURce[1|2]]:PHASe:INITiate Initiate output waveform phase synchronization