Tektronix NetTek Y400 User manual

Copyright ETektronix, Inc. All rights reserved
Warning!
To avoid injury, do not connect this product to any
source which may be subject to the effects of
lightning.
Important Safety Information
Review the following safety precautions to avoid
injury and prevent damage to this product or any
products connected to it.
Service. Only qualified personnel should perform
service procedures.
Power. Use only the Power cords, Desk Top Power
Supplies, Batteries, or In-Vehicle Power Adapters
specified for this product and certified for the country
of use. Observe all ratings marked on these parts.
Intended Use. The Y400 is intended for use only with
the specified application modules available from
Tektronix. Important safety information is contained
in the application module user manuals.
Read Application Module Manuals. Before operating
the Y400 NetTek Analyzer Platform, refer to the
application module manuals for:
HDetailed instructions on installing and charging
the battery. Recharge batteries for the recom-
mended charge cycle only.
HSystem specifications, environmental ratings, and
electrical ratings.
HGeneral safety warnings and cautions related to
operating the system and an explanation of the
safety symbols marked on the product.
HProper use of controls and settings, and proper
connection of inputs and outputs.
HProper use of the product’s shoulder strap, strand
hook, and other accessories.
HProper application module installation.
HProper system maintenance.
Layout
Batteries
Application
modules
PC card
Front panel
External
power
123 4
I/O ports
1.Power/Suspend button
2.Reset button
3.Status light
4.Battery charge/level light
Input and Output Ports
1234567
1.Microphone input
2.Headphone jack
3.Ethernet (RJ-45)
4.Serial (RS-232)
5.Keyboard
6.USB host
7.USB slave
Installing/Removing Batteries
Pull and lift tab:
Swing up retainer
Retainer in
open position
Lift battery by strap
1
2
3
Connecting Power Adapters
Power adapter jack
Charging Batteries
1.Connect AC or DC power adapter to Y400.
2.Connect AC or DC power adapter to appropriate
power source. The battery charge/level light turns
green.
3.Battery charge time (full charge):
HAnalyzer powered off: 4 hours
HAnalyzer powered on: 8 hours
For more information on battery charging, battery
calibration, and power management, select Start >
Help > Windows CE Basics > Tektronix NetTek
Analyzer Platform Basics > Power Management.
Powering On and Off the Analyzer
To power on the NetTek Analyzer, press the
Power/Suspend button (blue button at lower left
corner of instrument). Powering up the NetTek
Analyzer takes about 30 seconds.
To power off the NetTek Analyzer, do one of the
following:
HPress the Power/Suspend button
HSelect Start > Shutdown > Shutdown
For more information on the Shutdown menu
functions, select Start > Help > Windows CE Basics
> Tektronix NetTek Analyzer Platform Basics >
Shutting Down the Instrument

www.tektronix.com
Calibrating the Touch-Screen Display
You must calibrate the touch-screen display to
respond correctly to your taps before using the
NetTek Analyzer.
1.Select Start > Settings > Control Panel.
2.Open (double-tap) the Stylus icon.
3.In the Double-Tap tab, double-tap the
checkerboard grid at a comfortable speed with a
stylus or your finger. This sets the tap rate
sensitivity.
4.Select the Calibration tab.
5.Follow the on-screen instructions to set the
touch-screen location and pressure values. Apply
pressure to the touch-screen for approximately
5 seconds to register each tap.
6.Tap OK to close the dialog box.
7.Restart the NetTek Analyzer to save and apply the
touch-screen calibration settings.
Online Help
To access Windows CE online help, select
Start > Help.
For NetTek Analyzer-specific help, select Start >
Help > Windows CE Basics > Tektronix NetTek
Analyzer Platform Basics.
Some application windows have context-sensitive
help, as indicated by a question mark icon at the top
of the application screen. Selecting the context-sensi-
tive icon displays information about the active
application window.
Transportation and Lithium-Ion Batteries
Each Y400 lithium--ion battery pack contains less
than 8 grams of lithium, with individual cells each
containing less than 1.5 grams of lithium, as
measured by International Civil Aviation Organiza-
tion (ICAO) standards. Consult your air carrier for
applicability and determination of any special
lithium--ion battery transportation requirements.
Cleaning
1.Disconnect the NetTek Analyzer from the external
power adapter.
2.Close all NetTek Analyzer connector and battery
doors.
3.Install the bus door on the NetTek Analyzer or
application module.
4.Use a soft cloth dampened with a solution of
water and mild detergent. Do not immerse the
analyzer or use abrasive cleaners.
CAUTION.To prevent damage to external
surfaces, do not use chemicals that contain
acetone, benzene, toluene, xylene, or similar
solvents. Do not use bleach or ammonia
solutions for cleaning.
Contacting Tektronix
Web site: www.tektronix.com
Phone: [phone]
Address: Tektronix, Inc.
Department or name (if known)
14200 SW Karl Braun Drive
P.O. Box 500
Beaverton, OR 97077
USA
Email: [email protected]
Additional contact information is also located on the
online help system by selecting Start > Help >
Windows CE Basics > Tektronix NetTek Analyzer
Platform Basics > Contacting Tektronix.
For more information on the NetTek Analyzer,
including options and accessories, go to
www.tektronix.com and enter Y400 in the web page
search field.
EMC Compliance
EC Declaration of Conformity -- EMC
Meets intent of Directive 89/336/EEC for Electromagnetic
Compatibility. Compliance was demonstrated to the following
specifications as listed in the Official Journal of the European
Union:
EN 61326 EMC requirements for Class A electrical
equipment for measurement, control and
laboratory use. 1,2,3,4
IEC 61000-4-2 Electrostatic discharge immunity
(Performance criterion B)
IEC 61000-4-3 RF electromagnetic field immunity
(Performance criterion A)
IEC 61000-4-4 Electrical fast transient/burst immunity
(Performance criterion B)
IEC 61000-4-5 Power line surge immunity
(Performance criterion B)
IEC 61000-4-6 Conducted RF immunity
(Performance criterion A)
IEC 61000-4-11 Voltage dips and interruptions immunity
(Performance criterion B)
EN 61000-3-2 AC power line harmonic emissions
EN 61000-3-3 Voltage changes, fluctuations, and flicker
Australia/New Zealand Declaration of Conformity -- EMC
Complies with EMC provision of Radiocommunications Act per
the following standard(s): 2,3
AS/NZS 2064.1/2 Industrial, Scientific, and Medical
Equipment: 1992
1Platform EMC performance may be altered when operated
with an application module; EMC specifications for the
application module apply in that case.
2EMC compliance was demonstrated using high-quality
shielded interface cables.
3Emissions that exceed the limits of this standard may occur
when the instrument is connected to a test object.
4Minimum Immunity test requirement.
Y400
NetTekrAnalyzer
Setup Reference
*P071143000*
071-1430-00