Teldat M1 User manual

Teldat Router M1/M1L
Installation Manual
Copyright© Teldat Dm569-I Version 8.3 09/2017 Teldat S.A.
Teldat S.A. Manual
Teldat Router M1/M1L 1

Legal Notice
Warranty
This publication is subject to change.
Teldat S.A. offers no warranty whatsoever for information contained in this manual.
Teldat S.A. is not liable for any direct, indirect, collateral, consequential or any other damage connected to the deliv-
ery, supply or use of this manual.
Manual Teldat S.A.
2Teldat Router M1/M1L

Table of Contents
I RelatedDocuments................................. 1
Chapter1 AboutThisGuide.................................. 2
1.1 SupportedDevices................................... 2
1.2 Who should read this manual? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
1.3 When should this manual be read? . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
1.4 Whatisinthismanual?................................. 2
1.5 Whatisnotinthismanual? ............................... 2
1.6 How is the information organized? . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
1.7 TechnicalSupport ................................... 2
Chapter 2 Teldat M1 / Teldat M1L Devices . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2.1 Characteristics..................................... 4
2.1.1 PowerSupply..................................... 4
2.1.2 HardwareMonitoring.................................. 4
Chapter 3 Components and Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . 5
3.1 Components...................................... 5
3.1.1 FrontPanel...................................... 5
3.1.2 RearPanel ...................................... 7
3.1.3 SidePanels...................................... 7
3.1.4 UndersidePanel.................................... 8
3.2 ExpansionSlot..................................... 8
3.3 Installationinarack.................................. 10
3.3.1 Standalone ..................................... 10
3.3.2 Wallmounting.................................... 11
3.4 Plug-inModules................................... 12
3.4.1 Installation...................................... 12
3.4.2 Uninstall....................................... 12
3.5 PowerSource.................................... 12
3.5.1 Connecting to the power source . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
3.5.2 Connecting ..................................... 13
3.5.3 Disconnecting.................................... 13
3.6 RSTButton..................................... 13
3.6.1 Rebootingthedevice................................. 13
3.6.2 DefaultConfiguration................................. 13
Teldat S.A. Table of Contents
Teldat Router M1/M1L i

3.7 Connectingthedata.................................. 13
3.7.1 4-portEthernetSwitch................................. 14
3.7.2 WANConnection................................... 14
3.7.3 WWAN Antenna Connection (Cell connector). . . . . . . . . . . . . . . . . . . . . . . 14
3.7.4 Wireless LAN Antenna Connection (Wi-Fi connectors) . . . . . . . . . . . . . . . . . . . 16
3.7.5 Connecting a 3G USB device (USB connector) . . . . . . . . . . . . . . . . . . . . . . 16
3.7.6 Connecting for Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
3.8 InstallingtheSIMcard................................. 17
Chapter4 Compliance.................................... 19
4.1 ManufacturerInformation............................... 19
4.2 SafetyWarnings................................... 19
4.3 WEEEInformation.................................. 23
4.4 REACH....................................... 23
4.5 EC Declaration of Conformity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
4.6 CEMarking..................................... 24
4.7 NationalRestrictions................................. 25
4.8 OperatingFrequency................................. 25
4.9 FCCStatement.................................... 25
4.9.1 Federal Communications Commission Interference . . . . . . . . . . . . . . . . . . . . 25
4.9.2 FCC Radiation Exposure Statement. . . . . . . . . . . . . . . . . . . . . . . . . . . 25
4.9.3 Radio Frequency Interference Requirements . . . . . . . . . . . . . . . . . . . . . . . 25
4.10 ICStatement..................................... 26
4.10.1 CAN ICES-3 (B)/NMB-3(B). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Appendix A Technical Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
A.1 Troubleshooting................................... 27
A.2 Updatingthesoftware................................. 27
A.3 Connectingtothedevice ............................... 27
A.3.1 Connecting using the local console (Aux connector) . . . . . . . . . . . . . . . . . . . . 27
A.4 Licenses....................................... 28
A.5 Connectors ..................................... 28
A.5.1 LANConnector.................................... 29
A.5.2 WANConnector................................... 29
A.5.3 WWAN Connector (female) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
A.5.4 WLANConnector(male)................................ 30
A.5.5 USBConnector.................................... 30
A.5.6 ConfigurationConnector................................ 30
Table of Contents Teldat S.A.
ii Teldat Router M1/M1L

A.5.7 PowerSupplyConnector ............................... 30
A.6 TechnicalSpecifications ............................... 30
A.6.1 HardwareArchitecture................................. 31
A.6.2 LANInterface .................................... 31
A.6.3 WANInterface.................................... 31
A.6.4 WirelessWANInterface................................ 31
A.6.5 WirelessLANInterface................................ 31
A.6.6 USBInterface.................................... 32
A.6.7 ConfigurationInterface ................................ 32
A.6.8 PowerSupply.................................... 32
A.6.9 Dimensionsandweight................................ 32
A.6.10 Environmental Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
AppendixB RadioInformation................................. 33
B.1 RFLTESpecifications................................. 33
B.2 RF GSM/WCDMA Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
B.3 WIFISpecifications.................................. 34
Teldat S.A. Table of Contents
Teldat Router M1/M1L iii

Table of Contents Teldat S.A.
iv Teldat Router M1/M1L

I Related Documents
Teldat Dm748-I Software Updating
Teldat S.A. Related Documents
Teldat Router M1/M1L 1

Chapter 1 About This Guide
This installation guide for the Teldat M1 router family contains information on how to correctly install the device in a
working environment.
1.1 Supported Devices
The information provided in this installation guide only applies to the Teldat M1 router family.
1.2 Who should read this manual?
This manual should be read by the support personnel who need to configure, maintain and monitor the device.
1.3 When should this manual be read?
Read this guide as soon as you are ready to familiarize yourself with the device and its components.
This manual will help you understand your new device in greater depth.
1.4 What is in this manual?
This installation guide contains the following information:
• A description of the available features in the Teldat M1 routers.
• Technical specifications.
• Power supply requirements.
• Elements that can be connected when the router is operating.
• How to install and uninstall the modules and power sources.
• A description of the device LEDs and connectors.
• Troubleshooting.
1.5 What is not in this manual?
This manual does not contain information relative to the device software or its configuration. For information on how
to configure this device, please see the relevant protocol manuals to be found in the Teldat website: ht-
tp://www.teldat.com
1.6 How is the information organized?
Each chapter focuses on a specific part of the hardware and its components. All descriptive, technical specifications
and information on a component can be found in the relevant chapter.
1.7 Technical Support
Teldat S.A. offers a technical support service. Device software can be upgraded on a regular basis for maintenance
purposes and for new features.
Contact information:
Web: http://www.teldat.com
Tel.: [phone]
1 About This Guide Teldat S.A.
2Teldat Router M1/M1L

Fax: [phone]
Email: suppor[email protected]
Teldat S.A. 1 About This Guide
Teldat Router M1/M1L 3

Chapter 2 Teldat M1 / Teldat M1L Devices
2.1 Characteristics
2.1.1 Power Supply
For further information on the different Teldat M1 power supplies, please see Components and Power Supply on
page 5, under section Power Source on page 12.
2.1.2 Hardware Monitoring
The only way to monitor the Teldat M1 router family hardware is through the LEDs on the front panel. The LEDs
provide visual information on the state of the device. They indicate the condition of the hardware components, if
there is connectivity, data flow, etc.
For further information on the LEDs panel, please see Components on page 5.
2 Teldat M1 / Teldat M1L Devices Teldat S.A.
4Teldat Router M1/M1L

Chapter 3 Components and Power Supply
The following chapter provides detailed information on the chassis of the Teldat M1 router family and its compon-
ents. This information includes:
• Components.
• Information on assembly.
• Installing and uninstalling modules.
• Power supply.
• RST button.
• Data connection.
• SIM card installation.
3.1 Components
3.1.1 Front Panel
The following figure shows the front panel:
Fig. 1: Frontal Panel
The front panel elements are as follows:
FRONT PANEL ELEMENTS TABLE
Item Description
A Aux. RJ45 Connector, which provides access to the device’s local console for con-
figuration and monitoring purposes.
B LEDs panel.
C Tray for expansion card.
The LEDs panel provides information on the status of the components (if they are active or not) and on the network
activity.
LEDs table
LED Status Description
PSU Monochrome green Off -> no power through PSU.
On -> powered through PSU.
Slot Tricolor Off -> There is no card in the expan-
sion slot.
Red -> interface down.
Amber -> auto test.
Teldat S.A. 3 Components and Power Supply
Teldat Router M1/M1L 5

Green -> interface up (blinking, in
some cards, when there is connection
data activity).
USB Tricolor Off -> system stopped.
Red -> interface is unavailable be-
cause it is installing, it is not enabled
(shutdown) or due to auto-test failure.
Amber -> idle.
• Rapid blinking. It has not registered
in the network or the quality is in-
sufficient.
• Slow blinking. GSM connection
(GPRS).
• Steady. WCDMA (UMTS / HSDPA)
connection.
Blinking (green/red) -> activity/
maintenance.
Wi-Fi Bicolor Red -> interface down.
Green -> interface up.
Blinking (green/red) -> activity/
maintenance.
LAN Switch Tricolor Green -> connected. Blinking: con-
nection data activity.
Red -> disconnected.
Eth WAN Tricolor Green -> connected. Blinking: con-
nection data activity.
Amber -> blinking: auto-test.
Red -> disconnected.
Cell Tricolor Off -> system stopped.
Red -> interface is unavailable be-
cause it is installing, it’s not enabled
(shutdown) or due to auto-test failure.
Amber -> idle.
• Rapid blinking. It has not registered
in the network or the quality is in-
sufficient.
• Slow blinking. GSM connection
(GPRS).
• Steady. WCDMA (UMTS / HSDPA)
connection.
Green -> connected. Blinking: con-
nection data activity.
Coverage Monochrome Blue Indicates the coverage level the in-
ternal 3G module has. Level from 0
3 Components and Power Supply Teldat S.A.
6Teldat Router M1/M1L

(1, 2, 3, 4) (all the LEDs off) to 4 (all lit up).
3.1.2 Rear Panel
The following figure shows the rear panel. Here you will find the majority of the Teldat M1 router family connectors.
Fig. 2: Rear panel
The following table provides information on each connector as well as a description:
Rear panel elements
Item Description
A SIM Card. Slot where you can insert SIM card for the external 3G module.
B USB. Slot where you can insert a 3G USB modem.
C 4-port Gigabit Ethernet Switch.
D RST. Reset button. For further information on how the reset button works, please
see RST Button on page 13.
E WPS (Wireless Protected Setup). This allows for easy and secure configuration of
the WiFi network parameters.
F Wi-Fi Antenna nº3. This connector is used or not, depending on the Wi-Fi card the
router has.
G Eth WAN. WAN Gigabit Ethernet.
H On/Off switch.
I Power source connection (PSU).
3.1.3 Side Panels
Two Wi-Fi and two 3G antenna connectors are located on the side panels, two each on either side:
Fig. 3: Right hand side panel and Fig. 4: Left hand side panel
The connectors are as follows:
Side panel connectors
Item Description
A Wi-Fi antenna connectors.
Teldat S.A. 3 Components and Power Supply
Teldat Router M1/M1L 7

B 3G antenna connectors.
3.1.4 Underside Panel
The following elements can be found on the underside panel:
Fig. 4: Underside panel
The following table contains details on the significant elements on the underside panel:
Underside PANEL ELEMENTS TABLE
Item Description
A Internal 3G module SIM tray. Accessed from the underside of the router.
B Adhesive rubber feet (these are not required if mounted in a rack).
3.2 Expansion Slot
The Teldat M1 router family has an expansion slot, so you can increase its features and interfaces by inserting differ-
ent cards or boards.
This slot is located on the router’s front panel, as shown in Figure 6:
Fig. 5: Expansion slot
3 Components and Power Supply Teldat S.A.
8Teldat Router M1/M1L

To correctly insert the cards, please follow these steps:
(1) Switch off the device and remove the data cables as described in Disconnecting on page 13.
(2) Remove the device from the workplace and place it in a stable, safe location where it can be easily accessed
and handled.
(3) Unscrew the screws on the front panel in order to dismantle the tray that gives access to the expansion cards.
Please see Fig. 6 on page 9.
Fig. 6: Unscrewing the screws from the front panel tray
(4) Once unscrewed, pull out the tray from the front panel slot. Please see Fig. 7 on page 9.
Fig. 7: Extracting the tray from the front panel
(5) If the card is provided with the tray fixed, skip to the next step. Otherwise, once you have extracted the tray,
place the card in the correct position. Once this has been done, attach the card using the appropriate screws
(making sure you don't damage it during the tightening process). Please see Fig. 8 on page 9.
Fig. 8: Placing the expansion card
(6) Finally, insert the tray into the device once again using the appropriate guides. See Fig. 9 on page 10.
Teldat S.A. 3 Components and Power Supply
Teldat Router M1/M1L 9

Fig. 9: Inserting the expansion card
(7) Screw the tray to the device. See Fig. 10 on page 10.
Fig. 10: Screw the tray to the front panel
(8) Connect a terminal to the console and check that the device detects the expansion card.
3.3 Installation in a rack
The Teldat M1 device family can be installed in a 19” rack. The strips and screws needed are not provided by default
and need to be acquired separately.
Both strips are attached to the device by means of 4 screws, two on each side, as shown in Figure 11.
Fig. 11: Anchor bolts for a rack
3.3.1 Standalone
The Teldat M1 routers can be placed as a standalones on a flat, stable surface. The adhesive rubber feet must be
stuck to the underside panel to prevent the device from sliding.
3 Components and Power Supply Teldat S.A.
10 Teldat Router M1/M1L

Make sure there is enough space around the router (for ventilation purposes) and check that the electricity cables
can comfortably reach it.
3.3.2 Wall mounting
The Teldat M1 can be mounted on the wall. This optional kit can be ordered separately or together with the Teldat
M1.
The anchors to mount the device on the wall must be installed as shown in the following figure, using the screws
provided by the manufacturer.
Fig. 12: Wall mounting
Once the anchors have been placed, you can place the device on the wall as shown in the upper right hand figure.
Warning
The screws must go into a wall stud (wood) or a wall anchor of the appropriate type for the wall. Screws
into drywall are not strong enough to support the router.
The above figures show the wall-mounting features on the Teldat M1 router.
Wall-mounting elements
Item Description
1 Wall screws.
2 23.2 cm (9.13 inches).
3 Chassis mounting holes.
4 Router chassis.
5 Mounting surface.
(1) Place the two (or four) wall studs on the wall, or on any other vertical surface, horizontally and separately.
Warning
If you install the router in drywall, use hollow-wall anchors (8mm - 5/16 inch) to secure the screws.
If the screws are not properly anchored, the strain of the cables connected to the router back pan-
el could pull the router from the wall.
Teldat S.A. 3 Components and Power Supply
Teldat Router M1/M1L 11

(2) Place the router on the wall and attach it using the screws (3.5x30). The figure shows how to install it correctly,
so that it can be used safely.
3.4 Plug-in Modules
The 3G USB modem is the only module that can be inserted in the device. To view the list of supported 3G modems,
please visit the following website: http://www.teldat.com.
3.4.1 Installation
To install the USB modem, simply insert it in the USB slot on the rear panel as shown in the following figure:
Fig. 13: USB modem insertion slot
3.4.2 Uninstall
To remove the device, simply remove it from the slot where it was inserted. See Fig. 13 on page 12.
3.5 Power Source
The Teldat M1 router family is powered though an external AC/DC source.
Workplace conditions. Main characteristics
• Avoid humid and or dusty locations.
• Direct exposure to sunlight, as well as other heat sources, should be avoided. The device should not be placed
amongst papers, magazines or other elements that could hinder natural air circulation.
• The device should not be placed very close to strong electromagnetic fields (such as speakers, engines, etc.).
• Knocks and/or strong vibrations should be avoided during transport, operation and storage.
Warning
The electric current in power cables, telephone lines and communication cables is dangerous. To pre-
vent electric shocks, before installing, handling or opening the equipment covers, connect and discon-
nect the cables following the steps set forth in Connecting on page 13 andDisconnecting on page 13.
3.5.1 Connecting to the power source
To connect the power supply to the device, please follow the steps set forth in section Connecting on page 13.
To avoid electric shocks, residual current circulation and other unwanted effects, also affecting communications, the
following is recommended:
Warning
All interconnected communication devices should be plugged to THE SAME GROUNDED POWER
OUTLET, which should at the same time be of good quality (lower than 10 ohms).
Whether the workplace is provided with an uninterrupted power supply system (UPS), regulated supply
3 Components and Power Supply Teldat S.A.
12 Teldat Router M1/M1L

or it is independent from the rest (such as lighting, etc.); it is highly recommended that all data devices
should be connected to the same power source. This will avoid operating and premature aging prob-
lems of drivers and other components.
3.5.2 Connecting
• Make sure that the device’s power supply switch is in the OFF position (0).
• Ensure that the power supply is NOT connected to either the electricity or the device.
• Connect all data cables.
• Connect the power supply cable to the device.
• Connect the power supply cable to the electricity supply.
• Set the router’s power supply switch on the ON position (1).
3.5.3 Disconnecting
• Make sure that the device’s power supply switch is in the OFF position (0).
• Disconnect the power supply from the electricity supply.
• Disconnect the power supply from the device.
• Disconnect the data cables.
3.6 RST Button
The different features of the RST button are described below.
3.6.1 Rebooting the device
Once the device is operating normally, pressing the RST button will make it restart.
3.6.2 Default Configuration
The RST button allows you to boot the device with its default configuration through the following steps:
• With the device switched off, keep the RST button pressed and switch on the router through the ON/OFF switch
(1).
• The PSU LED (green) will light up and the LED Slot will begin to blink (amber). This blinking will continue for 10
seconds.
• For the device to boot with the default configuration, stop pressing the RST button while the LED Slot is blinking
(i.e. before the 10 second period expires).
The default configuration for the router establishes the access IP and mask address as follows:
• IP address: 192.168.1.1
• IP mask: 255.255.255.0
Note
Some devices leave the factory with customized settings. This personalization may mean that the de-
fault configuration is different from the one shown above.
3.7 Connecting the data
The Teldat M1 router family has the following data connections.
Teldat S.A. 3 Components and Power Supply
Teldat Router M1/M1L 13

3.7.1 4-port Ethernet Switch
The Teldat M1 router family incorporates a 4-port 10/100/1000 BaseT Switch with automatic MDI/MDIX to connect to
a local area network (LAN).
Please pay careful attention to the labeling so you do not mix this switch with other port types:
Fig. 14: LAN switch ports
Note
During booting and in BIOS mode, only the LAN 1 connector is available.
Warning
The equipment must be used with the power supply provided by the manufacturer.
3.7.2 WAN Connection
The Teldat M1 router family incorporates an Ethernet WAN 10/100/1000 BaseT port with automatic MDI/MDIX.
The WAN port is independent from the Switch and is handled as just one more interface.
Please pay careful attention to the labeling so you do not mix this switch with other port types:
Fig. 15: WAN PORT
Note
During booting and in BIOS mode, the WAN connector is not operative.
3.7.3 WWAN Antenna Connection (Cell connector)
The Teldat M1 router family has two connectors for 3G antennas. To assemble and disassemble the antennas,
simply screw them into the Cell connectors (located on the side panels of the router).
Installing these antennas in the Teldat M1 router is essential in order to improve the quality of the signal received
and transmitted by the cellular model.
3 Components and Power Supply Teldat S.A.
14 Teldat Router M1/M1L