Teldat K Seres User manual

Teldat K/KF router
Installation Manual
Copyright© Teldat-DM540-I Version 5.1 7/2015 Teldat S.A.
Teldat S.A. Manual
Teldat K/KF router 1

Legal Notice
Warranty
This publication is subject to change.
Teldat S.A. offers no warranty whatsoever for information contained in this manual.
Teldat S.A. is not liable for any direct, indirect, collateral, consequential or any other damage connected to the deliv-
ery, supply or use of this manual.
Manual Teldat S.A.
2Teldat K/KF router

Table of Contents
I RelatedDocuments................................. 1
Chapter1 AboutThisManual................................. 2
1.1 SupportedDevices................................... 2
1.2 Who should read this manual? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
1.3 When should this manual be read? . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
1.4 Whatisinthismanual?................................. 2
1.5 Whatisnotinthismanual? ............................... 2
1.6 How is the information organized? . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
1.7 TechnicalSupport ................................... 2
Chapter 2 Teldat K / Teldat KF Routers . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2.1 Features........................................ 4
2.1.1 Powersupply ..................................... 4
2.1.2 HardwareMonitoring.................................. 4
Chapter 3 Components and Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . 5
3.1 Components...................................... 5
3.1.1 FrontPanel...................................... 5
3.1.2 RearPanel ...................................... 5
3.1.3 SidePanels...................................... 6
3.1.4 UndersidePanel.................................... 6
3.1.5 TopPanel(LEDs).................................... 7
3.2 Mountinginrack.................................... 9
3.2.1 Standalone ...................................... 9
3.2.2 Wallmounting..................................... 9
3.3 Plug-inModules................................... 11
3.3.1 Installation...................................... 11
3.3.2 Uninstall....................................... 11
3.4 PowerSource.................................... 11
3.4.1 ExternalPowerSource................................ 12
3.4.2 PoE......................................... 12
3.4.3 Connecting ..................................... 12
3.4.4 Disconnect...................................... 13
3.5 RSTButton..................................... 13
3.5.1 Rebootingthedevice................................. 13
3.5.2 DefaultConfiguration................................. 13
Teldat S.A. Table of Contents
Teldat K/KF router i

3.5.3 CargalanMode.................................... 14
3.6 Connectingthedata.................................. 14
3.6.1 4-portEthernetSwitch................................. 14
3.6.2 WANConnection................................... 15
3.6.3 WWAN Antenna Connection (Cell connector). . . . . . . . . . . . . . . . . . . . . . . 15
3.6.4 Wireless LAN Antenna Connection (Wi-Fi connectors). . . . . . . . . . . . . . . . . . . 16
3.6.5 Connecting a 3G USB device (USB connector) . . . . . . . . . . . . . . . . . . . . . . 17
3.7 InstallingtheSIMcard................................. 17
Appendix A Technical Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
A.1 Troubleshooting................................... 19
A.2 Updatingthesoftware................................. 19
A.3 Connectingwiththerouter............................... 19
A.4 Licenses....................................... 20
A.5 Connectors ..................................... 20
A.5.1 LANConnector.................................... 20
A.5.2 WANConnector................................... 20
A.5.3 WWAN Connector (female) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
A.5.4 WLANConnector(male)................................ 21
A.5.5 USBConnector.................................... 21
A.5.6 PowerSupplyConnector ............................... 21
A.6 TechnicalSpecifications................................ 21
A.6.1 HardwareArchitecture................................. 21
A.6.2 LANInterface .................................... 22
A.6.3 WANInterface.................................... 22
A.6.4 WirelessWANInterface................................ 22
A.6.5 WirelessLANInterface................................ 22
A.6.6 USBInterface.................................... 22
A.6.7 ConfigurationInterface ................................ 23
A.6.8 PowerSupply.................................... 23
A.6.9 ExternalPowerSupply ................................ 23
A.6.10 Dimensionsandweight................................ 23
A.6.11 Environmental Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Appendix B Regulatory compliance and safety information . . . . . . . . . . . . . . . . . 24
B.1 Recycling and the Environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
B.2 Translated Safety Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
B.3 DeclarationofConformity............................... 26
B.3.1 Declaration of Conformity with regard to the EU Directive 1999/5/ED (R&TTE Directive) . . . . 28
B.3.2 Counties where the equipment is intended to be used . . . . . . . . . . . . . . . . . . . 28
B.3.3 CEMarking..................................... 28
Table of Contents Teldat S.A.
ii Teldat K/KF router

B.3.4 Product Usage Restrictions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
B.3.5 Third Party Software or Firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
B.3.6 Technical Documents on http://www.teldat.com. . . . . . . . . . . . . . . . . . . . . . 31
B.4 StandardsCompliance ................................ 31
B.4.1 FCC Regulatory Approval and Compliance. . . . . . . . . . . . . . . . . . . . . . . . 31
Teldat S.A. Table of Contents
Teldat K/KF router iii

Table of Contents Teldat S.A.
iv Teldat K/KF router

I Related Documents
Teldat-Dm 748-I Software Updating
Teldat S.A. Related Documents
Teldat K/KF router 1

Chapter 1 About This Manual
This is the installation manual for the Teldat K router family and contains information on how to correctly install this
device in a working environment.
1.1 Supported Devices
The information provided only applies to the Teldat K router family.
1.2 Who should read this manual?
This manual should be read by the support personnel who need to install, configure, maintain and monitor the
device.
1.3 When should this manual be read?
Read this guide as soon as you are ready to familiarize yourself with the device and its components.
This manual will help you understand your new device in greater depth.
1.4 What is in this manual?
This installation guide contains the following information:
• A description of the features available in the Teldat K family.
• Technical specifications.
• Power supply requirements.
• Elements you can connect to the device while it is running.
• Installation and removal procedures for modules and power supplies.
• A description of the LEDs and connectors of the device.
• Troubleshooting.
1.5 What is not in this manual?
This manual does not contain information on the device software or its configuration. For information on how to con-
figure this device, please see the relevant protocol manuals, which can be found on the Teldat website: ht-
tp://www.teldat.com .
1.6 How is the information organized?
Each chapter focuses on a specific part of the hardware and its components. All descriptive and technical specifica-
tions, or information on a component, can be found in the relevant chapter.
1.7 Technical Support
Teldat S.A. offers a technical support service. Device software can be upgraded on a regular basis for maintenance
purposes and for new features.
Contact information:
Web: http://www.teldat.com
1 About This Manual Teldat S.A.
2Teldat K/KF router

Tel.: [phone]
Fax: [phone]
Email: suppor[email protected]
Teldat S.A. 1 About This Manual
Teldat K/KF router 3

Chapter 2 Teldat K / Teldat KF Routers
2.1 Features
2.1.1 Power supply
For further information on the different power supplies in the Teldat K router family, please see Components and
Power Supply on page 5 in the section Power Source on page 11
2.1.2 Hardware Monitoring
The only way to monitor the Teldat K router family hardware is through the LEDs panel. The LEDs provide visual in-
formation on what is happening in the device. They indicate the state of the hardware components, if there is con-
nectivity, data flow, etc.
For further information on the LEDs panel, please see section Components on page 5.
2 Teldat K / Teldat KF Routers Teldat S.A.
4Teldat K/KF router

Chapter 3 Components and Power Supply
The following chapter provides detailed information on the chassis of the Teldat K router family and its components.
This information includes:
• Components.
• Information on assembly.
• Installation and removal of modules.
• Power supply.
• RST button.
• Data connection.
• SIM card installation.
3.1 Components
3.1.1 Front Panel
The following figure shows the front panel. The only thing to be found here are the 3G antenna connectors.
Fig. 1: Front Panel
The front panel elements are as follows:
Front panel elements
Item Description
A Main antenna for the Teldat K cellular module.
B Auxiliary antenna 2 for the Teldat K cellular module.
C Auxiliary antenna 1 for the Teldat K cellular module.
3.1.2 Rear Panel
The following figure shows the rear panel. Here you can see all the connectors for the Teldat K router family.
Fig. 2: Rear panel
The following table provides information on each connector as well as a description:
Rear panel elements
Teldat S.A. 3 Components and Power Supply
Teldat K/KF router 5

Item Description
A SIM Card. Slot where you can insert the SIM card for the external 3G module.
B USB. Slot where you can insert a 3G USB modem.
C 4-port Gigabit Ethernet Switch.
D RST. Reset button. For further information on how the reset button works, please
see “RST Button on page 13 in this chapter.
E WPS (Wireless Protected Setup). This allows for easy and secure configuration of
the WiFi network parameters.
F WiFi antenna no. 3. This connector is used or not depending on the WiFi card the
router has.
G Eth WAN/PoE In. WAN Gigabit Ethernet. This is also where the router is powered
through PoE.
H On/Off switch.
I Power source connection (PSU).
3.1.3 Side Panels
Two WiFi antennas are located on the side panels, one on either side.
Fig. 3: Right hand side panel and Fig. 4 Left hand side panel
3.1.4 Underside Panel
The following elements can be found on the underside panel:
3 Components and Power Supply Teldat S.A.
6Teldat K/KF router

Fig. 5: Underside panel
The following table contains details on the significant elements on the underside panel.
Underside panel elements table
Item Description
A SIM tray for the internal module. This is only found on the Teldat K. It’s accessed
from the underside of the router.
B Platform where the label containing the information on the product is placed. This
label contains information on the device model, mac, serial number, etc.
C Slots for wall mount.
3.1.5 Top Panel (LEDs)
The LEDs panel provides information on the state of the components (whether they are active or not) or on the net-
work activity.
Teldat S.A. 3 Components and Power Supply
Teldat K/KF router 7

Fig. 6: Leds panel
The LEDs for the Teldat K router family are shown in the above figure. The table below contains a description on
them.
LEDs table
LED Status Description
PoE Monochrome Green Off -> not being powered through
PoE.
On -> powered through PoE.
PSU Monochrome
Green
Off -> not being powered through
PSU
On -> powered through PSU
Alert - Not defined.
USB
.
Tricolor Off -> system is powered off.
Red -> interface is unavailable be-
cause it is installing; it is not enabled
(shutdown) or due to auto-test failure.
Amber -> idle.
• Rapid blinking. It has not registered
in the network or the quality is in-
sufficient.
• Slow blinking. GSM connection
(GPRS).
• Steady. WCDMA (UMTS / HSDPA)
connection.
Green -> connected. Blinking: con-
nection data activity.
Wi-Fi Bicolor Red -> interface down.
Green -> interface up.
3 Components and Power Supply Teldat S.A.
8Teldat K/KF router

Blinking (green/red) -> activity/
maintenance.
LAN Tricolor Green -> connected. Blinking: con-
nection data activity.
Red -> disconnected.
WAN Tricolor Green -> connected. Blinking: con-
nection data activity.
Amber -> blinking, auto-test.
Red -> disconnected.
Cell Tricolor Off -> system is powered off.
Red -> interface is unavailable be-
cause it is installing; it is not enabled
(shutdown) or due to auto-test failure.
Amber -> idle.
• Rapid blinking. It has not registered
in the network or the quality is in-
sufficient.
• Slow blinking. GSM connection
(GPRS).
• Steady. WCDMA (UMTS / HSDPA)
connection.
Green -> connected. Blinking: con-
nection data activity.
Coverage
(1, 2, 3, 4)
Monochrome blue Indicates the coverage level the 3G
internal module has. 0 level (all LEDs
off) to 4 (all LEDs on).
3.2 Mounting in rack
The Teldat K router family cannot be mounted in a rack. However there are other types of mounting.
3.2.1 Standalone
Any router from the Teldat K family can be placed as a standalone device on a flat, stable surface.
You need to make sure that there is enough space around the router for ventilation purposes and ensure that the
electricity cables can reach it.
3.2.2 Wall mounting
The Teldat K can be mounted on the wall. The Teldat KF can be as well, but this doesn’t make much sense as it
doesn’t have a 3G module incorporated.
There are two slots on the underside of the device which are used to fix it to the wall. You can see this in section
“Underside Panel on page 6.
You must provide the screws and wall anchors. We recommend the following accessories for wall mounting, valid for
solid wall and Gypsum board (plaster) wall:
• 2 screws: [COACH SCREW HEAD 90 DEGR.POZIDR. 3.5x30]
Teldat S.A. 3 Components and Power Supply
Teldat K/KF router 9

• 2 wall anchors: [WHITE STRIATED WALL ANCHOR DIAM.8mm]
Warning
The screws must go into a wall stud (wood) or a wall anchor of the appropriate type for the wall. Screws
into drywall are not strong enough to mount the router.
Fig. 7: Wall-Mounting Features on the Teldat K/KF router
Figure 7 shows the wall-mounting features on the Teldat K/KF routers.
1 Wall screws 2 10.2 cm (4.02 inches)
3 Chassis mounting holes (on
bottom)
4 Router chassis
5 Mounting surface
To mount the router on a wall or other surface, follow these steps:
Procedure
Step 1 Install the two screws (3.5x30) horizontally apart on a wall or any other vertical surface.
The screws should protrude 0.6 cm (0.25 inch) from the surface of the wall.
3 Components and Power Supply Teldat S.A.
10 Teldat K/KF router

Warning
If you install the screws in drywall, use hollow-wall anchors (8 mm – 5/16 inch) to secure the screws. If
the screws are not properly anchored, the strain of the cables connected to the router back panel could
pull the router from the wall.
Step 2 Hang the router on the screws. This is the appropriate orientation for safe use (see Fig. 7 on page 10).
Note
• The accessories for wall mounting the device are not provided in the package, and have to be ac-
quired separately.
• The accessories must be properly adapted to the kind of wall and must be chosen to ensure that they
can support the weight of the device.
3.3 Plug-in Modules
The only module that can be inserted in the device is the USB 3G modem. To view the list of supported 3G modems,
please visit the Teldat website: http://www.teldat.com .
3.3.1 Installation
In order to install the USB modem, simply insert it in the USB slot on the rear panel as shown in the following figure:
Fig. 8: USB modem insertion slot
3.3.2 Uninstall
To remove the device, simply remove it from the slot where it was inserted. See Fig. 8 on page 11.
3.4 Power Source
The Teldat K router family is powered though an external AC/DC source or through an Ethernet cable (if it complies
with the POE 802.3at standard).
Warning
The equipment must be used with the power supply provided by the manufacturer, or equivalent.
Workplace Conditions. Main Characteristics
• Avoid humid and or dusty locations.
• Direct exposure to sunlight should be avoided as well as other heat sources. The device should not be placed
amongst papers, magazines or other elements that could hinder natural air circulation.
• The device should not be placed very close to strong electromagnetic fields such as speakers, engines, etc.
• Knocks and/or strong vibrations should be avoided during transport, operation and storage.
Teldat S.A. 3 Components and Power Supply
Teldat K/KF router 11

Warning
The electric current in power cables, telephone lines and communication cables is dangerous. To pre-
vent electric shocks, before installing, handling or opening the equipment covers, connect and discon-
nect the cables following the steps set in Connecting on page 12 andDisconnect on page 13.
3.4.1 External Power Source
To connect the power supply to the device, please follow the steps outlined in section “ If the Ethernet cable isn’t PoE
on page 13.
To avoid electric shocks, residual current circulation and other unwanted effects, also affecting communications, the
following is recommended:
Warning
All interconnected communication devices should be plugged to THE SAME GROUNDED POWER
OUTLET, which should at the same time be of good quality (lower than 10 ohms).
Whether the workplace is provided with an uninterrupted power supply system (UPS), regulated supply
or it is independent from the rest (such as lighting, etc.); it is highly recommended that all data devices
should be connected to the same power source. This will avoid operating and premature aging prob-
lems of drivers and other components.
3.4.2 PoE
The Teldat K router family can be powered through an Ethernet cable if the latter complies with the POE 802.3at
standard. The port enabled for this is the Eth WAN.
To connect the Ethernet cable with PoE power to the router, please carry out the steps outlined in section “ If the Eth-
ernet cable is PoE on page 13.
The following figure illustrates how to connect the PoE injector to the device.
Fig. 9: Diagram showing how to connect the PoE injector to the device
3.4.3 Connecting
3 Components and Power Supply Teldat S.A.
12 Teldat K/KF router

3.4.3.1 If the Ethernet cable isn’t PoE
• Make sure that the router’s power supply switch is in the OFF position (0).
• Ensure that the power supply is NOT connected to either the electricity or the router.
• Connect all data cables.
• Connect the power supply cable to the device.
• Connect the power supply cable to the electricity supply.
• Set the router’s power supply switch to the ON position (1).
3.4.3.2 If the Ethernet cable is PoE
• Check that the Ethernet cable going to be used for power is NOT connected to the router.
• Make sure that the router’s power supply switch is in the OFF position (0).
• Ensure that the power supply is NOT connected to the electricity supply.
• Connect all data cables.
• If you need redundant power, connect the power supply to the device.
• If you need redundant power, connect the power supply to the electricity supply.
• Connect the Ethernet cable.
• Set the router’s power supply switch to the ON position (1).
3.4.4 Disconnect
3.4.4.1 If the Ethernet cable isn’t PoE
• Make sure that the router’s power supply switch is in the OFF position (0).
• Disconnect the power supply from the electricity supply.
• Disconnect the power supply from the router.
• Disconnect the data cables.
3.4.4.2 If the Ethernet cable is PoE
• Disconnect the Ethernet cable.
• Make sure that the router’s power supply switch is in the OFF position (0).
• Disconnect the power supply from the electricity supply.
• Disconnect the data cables.
3.5 RST Button
The different features of the RST button are described below.
3.5.1 Rebooting the device
Once the device is operating normally, if you press the RST button, this will restart.
3.5.2 Default Configuration
The RST button allows you to boot the device with its default configuration through the following steps:
• With the device switched off, keep the RST button pressed and switch on the router through the ON/OFF switch
(1).
• The PSU LED (green) will light up and the Alert LED will begin to blink (amber). This blinking will continue for 10
seconds.
Teldat S.A. 3 Components and Power Supply
Teldat K/KF router 13

• So that the device boots with the default configuration, you need to release the RST button while the Alert LED is
blinking, i.e. before the 10 second period expires.
The router’s default configuration sets the following IP address and mask:
• IP address: 192.168.1.1
• IP mask: 255.255.255.0
Note
Some devices leave the factory with customized settings for a client. This personalization means that
the device may have a different default configuration from the one shown above.
3.5.3 Cargalan Mode
Setting the cargalan mode enables you to send the router files such as BIOS, a distribution or a configuration file.
For the router to enter this mode, you need to follow these steps:
• With the device switched off, keep the RST button pressed and switch on the router through the ON/OFF switch
(1).
• The PSU LED (green) will light up and the Alert LED will begin to blink (amber). This blinking will continue for 10
seconds.
• Once the Alter LED stops blinking, it will light up in steady green. At that point the USB LED will begin to blink
(amber). This blinking will continue for 3 seconds.
• The router will enter in the cargalan mode if you release the RST button while the USB LED is blinking.
Once the device is in this mode, you can start downloading files up to a maximum of 5. The loading procedure is as
follows:
• Send a file while the LED is blinking in amber.
• When the whole file has arrived, it is then recorded while the LED blinks in red and green.
• If the file has recorded correctly, the LED will light up in steady green and the next LED will begin to blink in amber
indicating that you can send another file. This occurs up to a maximum of five times, when the Cell LED, which is
the last one, will then light up in steady green.
3.6 Connecting the data
The Teldat K router family has the following data connections.
3.6.1 4-port Ethernet Switch
The Teldat K router family incorporates a 4-port 10/100/1000 BaseT Switch with automatic MDI/MDIX to connect to
a local area network (LAN).
Please pay careful attention to the labeling so you do not confuse this switch with other types of ports:
Fig. 10: LAN switch PORTs
Note
During booting and in BIOS mode, only the LAN 1 connector is available.
3 Components and Power Supply Teldat S.A.
14 Teldat K/KF router