Telehook TH-AN-CM User manual

Dry Wall Anchor
Screw
TM
Component Checklist
Installation Instructions
TELEHOOK
Cable Manager
Wall Plate
10g x 30mm
Screw (x4)
(Check you have received all parts against the Component Checklist below)
End Cap (x2)
Cable Tabs (x8)
A Mount the Wall Plate
Mounting Tips:
Nylon Wall
Plug (x4)
4mm (3/16”)
hole
10g x 30mm
screw
Nylon Wall Plug
6mm
(1/4”)
hole
Wall Plate
Telehook
Cable
Manager
Display
Timber Stud Wall Masonry
Optional Shelf
(sold separately)
Dry Wall
Anchor (x6)
Telehook Cable Manager has been designed to hide the cables of a wall mounted display.
Therefore, it is recommended that it is mounted vertically and centrally below your display.
The adjoining image shows a typical Cable Manager installation.
Ideally, the top of Telehook Cable Manager should sit just under the lower edge of your display
with the bottom of Telehook Cable Manager (i.e. the End Cap) sitting approximately 50mm (2")
above the floor or skirting board.
IMPORTANT: Ensure the lower edge of the Wall Plate is positioned no less than 50mm
(2”) above the skirting board so that there is enough room to accommodate the End Cap
Front Fascia
Tools Required: Power drill 4mm ( 3/16”) drill bit 6mm ( 1/4”) drill bit Phillips head screwdriver
M4 x 5mm Grub
Screw (x4)
Timber Stud
Dry Wall
Mounting
Hole
Pattern
Dry
Wall
Anchor Mounting
Hole
Pattern
To determine the best position for your Cable Manager, see “Mounting Tips” below
6mm
(1/4”)
hole
IMPORTANT: For Dry Wall Installation
use alternating mounting holes
10g x 30mm
screw
Masonry
Wall
Dry Wall
2mm Allen Key
End Cap
End Profile
End Profile
Bits Box
It is recommended that your display be installed prior to the installation of this product.
If you wish to paint your Cable Manager, please consult your paint specialist for advice.
Surface finish: Clear Anodised Aluminium
IMPORTANT NOTES
OR OR
Mounting
Hole
Pattern
TH-AN-CM

Due to continuing product development, the manufacturer reserves the right to alter specifications without notice. Published: 02.03.12©
B Mount your Display
Mount your display onto its wall mount bracket
Connect all the required cables to the display and if necessary, manoeuvre it into its final viewing position
C Installing Cables
Display on
wall mount
bracket
Wall Plate
Install the display’s cables into the left,
right and centre cable bays as shown
F Insert Front Fascia
E Attach End Caps
TOP VIEW
Attach an End Cap onto
both ends of the Wall
Plate and secure in place
using the M4 Grub
Screws as shown.
NOTE:
If possible, separate the display’s
power cable from the data cables
(i.e. hi-fi & speaker cables) by
installing them into separate cable
bays. This will reduce the chance of
electromagnetic interference. The
diagram to the right shows an
example installation setup.
Left cable bay
Centre cable bay
(best for display power cable)
Right cable bay
Data cables
(can also be installed
into the same bay)
TOP VIEW
Using two hands,
flex the End Cap
around the
display’s cables
and manoeuvre
them into their
corresponding End
Cap Cable Bay
F.1.
Partially insert the
front facia as shown
Front Fascia
TOP VIEW
F.2.
Push the edge of the
Front Facia until it snaps
into place
F.3. Repeat F.2.
down the length
of the Front Facia
until it is firmly
secured onto the
Wall Plate
End Cap Cable Bay
Display Power
cable
A
B
2mm
Allen
Key
M4
Grub
Screw
WARNING: DO
NOT OVER TIGHTEN Installation Complete
D Insert Cable Clips
Insert the Cable Tabs into
the Wall Plate to Secure
Cables in place.
If required, cables can exit
from the side of the Cable
Manager. In this case, use
the left or right cable bays
only.
Cable
Tab
E.1.
Using your
thumb and
index finger,
flex the Cable
Tab into a
concave shape
E.2.
Twist the Cable
Tabs into the small
slots in the Wall
Plate
Cables exiting from the side