Jason.L Switch 4 Person workstations with Uniform... User manual

Note: Please ignore any pre-drilled holes or nut inserts that maybe present in your top(s). They will not match your
particular table/desk base and woods screws will be required to be screwed directly into the underside of the top.
Note: It is important to fully tighten all bolts and screws before attaching the top(s) so that the frame
is suciently rigid. Failure to do this may aect stability once the tops are attached.
Tools Required: Power screwdriver.
INSTALLATION GUIDE
Switch 4 Person
workstations with
Uniform Spine
Page 1 of 14
Need help!
Call us on
1300 527 665
www.jasonl.com.au

INSTALLATION GUIDE
Switch 4 Person
workstations with
Uniform Spine
Page 2 of 14
Need help!
Call us on
1300 527 665
www.jasonl.com.au
To begin, we need to assemble the desks.
Please carefully follow the following steps.
Repeat the process for each desk until all
4 have been completed.

Table Top (1400x800mm)
Leg x4
Leg Bracket x4
Beam Bracket x8
Long Beam x2 (925mm)
Short Beam x2 (325mm)
L-Bracket x10
1
2
3
4
5
6
7
Hex Nut x4
L-Bracket screws x10
Hex Head screws x16
M8x25mm Dome Head x4
8
9
10
11
COMPONENTS
SCREWS
Page 3 of 14
INSTALLATION GUIDE
Switch 4 Person
workstations with
Uniform Spine
Need help!
Call us on
1300 527 665
www.jasonl.com.au
6
5
4
3
7
9
11
2
8
1

Page 4 of 14
INSTALLATION GUIDE
Switch 4 Person
workstations with
Uniform Spine
Need help!
Call us on
1300 527 665
www.jasonl.com.au
Join 3 L-Bracket through each Long Beam
and 2 L-Bracket through each Short Beam.
Join Leg Brackets to each Leg using screws to secure them, as follow.
Securely connect each Beam to each Beam Bracket. Screw to secure. Insert Hex Nut on each Beam Bracket.
01
03 04
02

Page 5 of 14
INSTALLATION GUIDE
Switch 4 Person
workstations with
Uniform Spine
Need help!
Call us on
1300 527 665
www.jasonl.com.au
Position as presented, and proceed to screw to ensure each corner of the frame.
05
If this bolt does not drop into the joint
use the Allen key to screw it all the way
in so that it creates its own thread.
This will ensure a nice, tight joint. Directly screw into table tops, using L-Bracket
screws through each L-Bracket.
06
Note: It is important to fully tighten all bolts and screws
before attaching the top(s) so that the frame is suciently
rigid. Failure to do this may aect stability once the tops
are attached.

ASSEMBLY INSTRUCTIONS
Switch 4 Person
workstations with
Uniform Spine
Page 6 of 14
Need help!
Call us on
1300 527 665
www.jasonl.com.au
Let's move on to storage now. Please
follow the steps below. Repeat the pro-
cess for each storage until all 4 have
been completed.

Page 7 of 14
Need help!
Call us on
1300 527 665
www.jasonl.com.au
ASSEMBLY INSTRUCTIONS
Switch 4 Person
workstations with
Uniform Spine
Components: Hardware:
Minifix Cam
14 pcs
Minifix Steel Bolt
14 pcs
Rubber Wood Dowel
19 pcs
Push Lock
1 sets
- Back Panel -
Qty : 1 pc
- Base Panel -
Qty : 1 pc
- Top Rail -
Qty : 1 pc
-Shelf-
Qty : 1 pc
- Side Panel -
Qty : 2 pcs
- Door Panel -
Qty : 2 pcs
- Door Rail-
Qty : 1 pc
Door Panel Rail Guide
4 sets (already installed) Stripe Handle
2 sets
Leveller N2880
Plastic Cap
5 pcs
Adjustable
Leveller N2880
5 pcs
Adjustable
Leveller N2881
5 pcs
Chipboard
Screw 4 x16mm
20 pcs

Page 8 of 14
Need help!
Call us on
1300 527 665
www.jasonl.com.au
ASSEMBLY INSTRUCTIONS
Switch 4 Person
workstations with
Uniform Spine
7
64
1
5
2
3
Exploded
view

Need help!
Call us on
1300 527 665
www.jasonl.com.au
ASSEMBLY INSTRUCTIONS
Switch 4 Person
workstations with
Uniform Spine
Page 9 of 14
Minifix Steel Bolt
Back panel Side panels
Rubber Wood Dowel

Need help!
Call us on
1300 527 665
www.jasonl.com.au
ASSEMBLY INSTRUCTIONS
Switch 4 Person
workstations with
Uniform Spine
Page 10 of 14
Minifix Steel Bolt
Door Rail Base Panel
Top Rail
Rubber Wood Dowel

Page 11 of 14
Need help!
Call us on
1300 527 665
www.jasonl.com.au
ASSEMBLY INSTRUCTIONS
Switch 4 Person
workstations with
Uniform Spine
Add side panel (6) & Shelf (7) at the same time.
Attach levellers with Chipboard Screw 4x16 at
bottom of carcass
Lay back panel (1) on ground.
Add one side panel (2) and
base panel (3)
STEP 01
Add top rail (4) & centre panel (5)
STEP 02
STEP 03
Chipboard
Screw 4 x32mm
Adjustable Leveller
N2880
Leveller N2880 Cap
DECO-CAP-18X15
5-pcs

Page 12 of 14
Need help!
Call us on
1300 527 665
www.jasonl.com.au
ASSEMBLY INSTRUCTIONS
Switch 4 Person
workstations with
Uniform Spine
8
8
10
Assemble Top Panel at top of two of the
carcass and complete assembly.
The other two storages will have a
Planter box. For those, top panel (No 10)
needs to be replaced with planter box
bottom panel and complete assembly.
Assembly MFC sliding doors
STEP 04
STEP 05
PUSH

Planter Box assembly Step 1.
Assemble component follow sequence number
Step 2.
Insert collar stud into boringhole
Note For Minifix Cam
Important: Function of Klix cam
1/4 RIGHT TURN FOR
LOCKING Make Sure The Arrow Is Pointing
Upwards Before InsertingInto The Panel'sHole
TOP PANEL
Qty : 1 pc
BASE PANEL
Qty : 1 pc
FRONT PANEL
Qty : 1 pc
SIDE PANEL L
Qty : 1 pc
SIDE PANEL R
Qty : 1 pc
BACK PANEL
Qty : 1 pc
1 2
34
5
6
Collar Stud
262.24.710
4 pcs
Minifix Steel
Bolt 10259
16 pcs
DECO-CAP
16x5
16 pcs
1
2
3
4
5
Note:
The bottom panel should be
facing down. Screws holes must
be seen from the outside only.
Bottom view
6
Insert Collar Stud
into Boring Hole
ASSEMBLY INSTRUCTIONS
Switch 4 Person
workstations with
Uniform Spine
Need help!
Call us on
1300 527 665
www.jasonl.com.au
Page 13 of 14

Assemble planter box bottom
panel on top of carcass and
complete assembly
STEP 05
Tighten Minifix
Connecting into
Boring Hole.
ASSEMBLY INSTRUCTIONS
Switch 4 Person
workstations with
Uniform Spine
Need help!
Call us on
1300 527 665
www.jasonl.com.au
Page 14 of 14