Tellur TLL331081 User manual

Smart Flood Sensor
User Manual
TLL331081

1. PRODUCT OVERVIEW
Smart flood sensor is a smart flood sensor (water leak sensor)
based on wireless solution. While a water leak happens, the
device will wake up the Wi-Fi connection to Wi-Fi router, send
an alarm signal to your mobile phone via Wi-Fi network, in the
case that the APP internet is available locally or remotely. The
alarm is selectable as a notification on your mobile phone with
bar display, banner with tone, vibration based on the APP
Notification setting on your Mobile Phone. There is an around
5-second delay from the state changes to notification on your
mobile phone depending on the internet connection quality.
The device will buzz if a water leak is detected till the leak is
removed. This device is working as a scene to trigger other
device action that are compatible in same APP such as to turn
on/off plug and bulb.
2. PRODUCT FEATURES
• Support buzz in water leak situation
• Working in 802.11 b/g/n;
• Support EZ (Smart Config) and AP(Access Point) mode for
Wireless connection;
• Support water leak detection;
• Support battery level detection and low battery alarm;
• Support 2xAAA battery powered;
• Wall mounted installation with extended detecting cable to 2
meters;
• Led indicates the working state;
• Compliant with CE, FCC and ROHS;
How to Get the device working:
• Make sure your Wi-Fi network work in 802.11 b/g/n 2.4GHz
and internet available;
• Download the APP from Apple store or Google Play;
• Register an account in APP and login with your email
address or Mobile phone number;
• Setup the device Wi-Fi connection;
• Mount device on specified location;
• Test and check the Device and APP working state;

3. PRODUCT DESCRIPTION
Button activities and LED indicator:
1) LED indicator: indicate the device working state:
• Fast blinking in Red: EZ mode (Smart config) for Wi-Fi
configuration;
• Slow blinking in Red: AP Mode for Wi-Fi configuration;
• Flash once in Blue: Wi-Fi connected, and water leak
detected;
• Flash once in Dual-Color: Wi-Fi disconnected and water leak
detected;
2) Probe: extend to detect the water leak;
3) Buzz vent: Sounds while water leak detected;
4) Button: Press and hold the button for 5 seconds to enter
into Wi-Fi connection (or configuration). The red LED
indicator will blink rapidly (EZ mode) or slowly (AP mode).
EZ mode connection is set as default in Wi-Fi configuration.
Press and hold the button for 5 seconds will enable the
device switch between EZ mode and AP mode.
LED indicator Buzz vent
Button
Probe

Note:
1) To check the device is working or not: short-cut the probe,
the LED indicator will flash and the Buzz will works;
2) To check the device is Wi-Fi connected or not: if the LED
indicator turns purple, the device is non Wi-Fi connected. If
the LED indicator turns blue, the device is Wi-Fi connected.
4. PRODUCT SPECIFICATIONS
• Power supply: 2 x AAA battery, 3V
• Battery life: Up to 6 months
• Flood notifications: Yes
• Acoustic alarm: Yes
• Low battery notifications: Yes
• Probe cable length: 2 meters
• WiFi standard: IEEE 802.11b/g/n
• Supported WiFi network: 2.4GHz
• Dimensions: 7cm x 7cm x 2cm
• Weight: 75 gr
5. INSTALL APP AND REGISTER AN ACCOUNT
Download the Tellur Smart App for both iOS and Android OS.
Scan the QR code to download Tellur Smart App
Set up router
This device only supports 2.4GHz frequency band router, does
not support 5GHz frequency band router, please set the
relevant parameters of the router before WiFi configuration,
WiFi passwords do not include special characters such as
Android
IOS
·Support
Download App(IOS&android)

~!@#$%^&*(). When the device is configured in WiFi, the
mobile phone and device are as close as to the router, which
can speed up the configuration of the device.
6. ADD AND REMOVE DEVICE IN YOUR APP ACCOUNT
6.1 Launch the APP and login, Click tADD DEVICES -> All ->
Flood sensor to start the device adding.
6.2 Press the device button for 5 seconds to enter the Wi-Fi
configuration state (fast blinking in EZ mode or slow
blinking in AP mode).
6.3 Input the Wi-Fi SSID and password of the Wi-Fi network
that the device is going to work with, then waiting around
30 seconds for the Wi-Fi configuration finished until a
device is successfully added;
6.4 Change the device name and share it within APP account
as you want.

6.5 Click the device just added to launch the device state UI to
check the state, battery level, record history and the APP
notification setting.
• EZ mode: make sure your APP is internet available and
device and APP both work in EZ mode. Then input the Wi-Fi
network password to finish the device adding. If you want to
change the Wi-Fi network, please check the “Change
network” in APP;

• AP mode: Click AP Mode, make sure your APP is internet
available and device and APP both work in AP mode. Confirm
to input the SSID and Password of Wi-Fi network, then select
the Device AP name in Wi-Fi list then back to App to finish the
device adding.
After the device is successfully added to APP account, the LED
will turn off. Using the methods mentioned in LED indicator to
check the device is successfully added or not. If not, please
repeat the Device adding again.
6.6 Remove device
1) Click “Remove Device” to remove this device from your
account; click “Restore manufacturer Defaults” to remove
the device from your account and clear the history record in
cloud.
2) After remove device or Restore manufacturer defaults from
the APP, repeating the Device add steps to your account;

7. INSTALLATION
7.1 AAA battery installation
1) Hold the battery cover and rotate it counter-clockwise to
open the battery cover
2) Put 2xAAA battery in with the correct positive and negative
electrode.
3) Close the cover and turn it clockwise
Left position Right position

7.2 Mount the device on the wall
There are two methods to mount the device on the wall.
3M Tape mode
• Stick the included self-adhesive
pads to the bottom of the device.
• Peel off the protective layer
of the sticker.
• Stick the device onto the wall.
Screw mode
1) Mark a hole location as
below picture and drill a
hole on thewall accordingly.
2) Screw the two bolts within the package on the wall leaving
the around 5~8mm bolt margin out of the wall. Then hang
the device on the two bolts.

7.3 Install the probe case on the wall with a 3M tape,
keep no gap between the probe and floor.
Note:
The notifications cannot be alerted on APP with my Android
System?
1. Make sure the alarm setting in APP is enabled
2. Make sure the Push notification is enabled for this APP for
Android system;

Declaration of conformity
We, ABN SYSTEMS INTERNATIONAL S.R.L., Bucharest, Sector
1, Marinarilor street, nr. 31, we declare on own responsibility
that the product below:
Product description: WiFi Smart Flood sensor
Brand: Tellur
Product code: TLL331081
It does not endanger life, health, work safety, does not have a
negative impact on the environment and
corresponds to the standards stated in the manufacturer's
declaration of conformity.
The product is in compliance with the following standards and
/ or other normative documents:
RED – 2014/53/EU
Applied standards:
EMC: ETSI EN 301 489-1 V2.2.0 (2017-03)
ETSI EN 301 489-17 V3.2.0 (2017-03)
Radio: ETSI EN 300 328 V2.1.1 (2016-11)
Health: EN 62479:2010
Safety: EN
60950-1:2006+A11:2009+A1:2010+A12:2011+A2:2013
RoHS – 2011/65/EU (RoHS 2.0)
The product bears CE mark, applied in 2019
Name: George Barbu
Function: General manager
Place and date: Bucharest, 19-03-2019
Signed:

Disposal and recycling information
The crossed-out wheeled-bin symbol on your
product, battery, literature or packaging reminds
you that all electronic products and batteries must
be taken to separate waste collection points at the
end of their working lives; they must not be disposed
of in the normal waste stream with household
garbage. It is the responsibility of the user to dispose
of the equipment using a designated collection point
or service for separate recycling of waste electrical
and electronic equipment (WEEE) and batteries
according to local laws. Proper collection and
recycling of your equipment helps ensure EEE waste
is recycled in a manner that conserves valuable
materials and protects human health and the
environment, improper handling, accidental
breakage, damage, and/or improper recycling at the
end of its life may be harmful for health and
environment.