Teltonika RUT200 User manual

https://wiki.teltonika-networks.com/view/QSG_RUT200
QSG RUT200
Main Page > RUT Routers > RUT200 > QSG RUT200
This Wiki page contains the online version of the Quick Start Guide (QSG) for the RUT200 LTE
Router. Here you will find an overview of the various components on the front and back of a
RUT200 device, hardware installation instructions, first login information, device specifications, and
general safety information. It is highly recommended to acquaint yourself with the Quick Start Guide
before using the device. You can also locate a printed version of the Quick Start Guide in the
packaging box of your device.
Contents
• 1 Safety information
- 1.1 General
- 1.2 RF exposure
- 1.3 Operating conditions
- 1.4 Faulty and damaged products
- 1.5 Electrical safety
- 1.6 Product handling
• 2 Front view
• 3 Back view
• 4 Connectors
• 5 Video Quick Start Guide
• 6 Hardware installation
• 7 Configure your computer (Windows)
• 8 Login to device
• 9 SIM card recommendations
Safety information
Before starting operating the device, please review recommendations and precautions to minimize
the possibility of accidents. Safety precautions presented are supplementary and subject to the local
safety regulations. When various operations are executed on the device, the user must fully follow
the safety instructions and recommendations provided with the device.
General
Radio specifications
RF technologies 2G, 3G, 4G, WiFi
Max RF power 33 dBm@GSM, 24 dBm@WCDMA, 23 dBm@LTE, 20 dBm@WiFi
Bundled accessories specifications*
Power adapter Input: 0.45A@100-240 VAC, Output: 9 VDC, 1A, 4-pin plug
Mobile antenna 698~960/1710~2690 MHz, 50 Ω, VSWR<3, gain** 4 dBi, omnidirectional, SMA
male connector

WiFi antenna 2400~2500 MHz, 50Ω, VSWR<2.5, gain** 5dBi, omnidirectional, RP-SMA male
connector
* Order code dependant.
** Higher gain antenna can be connected to compensate for cable attenuation when a cable is used. The user is
responsible for the compliance with the legal regulations.
RUT200 router must be used in compliance with any and all applicable national and international
laws and with any special restrictions regulating the utilization of the communication module in
prescribed applications and environments.
NCC
-取得審驗證明之低功率射頻器材，非經核准，公司、商號或使用者均不得擅自變更頻率、加大功率或變更原設計之特性及功能。低功率射頻器材之使用不得影響飛航安全及干擾合法通信；經發現
有干擾現象時，應立即停用，並改善至無干擾時方得繼續使用。前述合法通信，指依電信管理法規定作業之無線電通信。低功率射頻器材須忍受合法通信或工業、科學及醫療用電波輻射性電機設
備之干擾。
-減少電磁波影響，請妥適使用
Detailed compliance information is available at the following internet address: wiki.teltonika-
networks.com/view/Certificates.
This sign means that is necessary to read the User's Manual before you start using the device.
This sign on the package means that all used electronic and electric equipment should not be
mixed with general household waste.
RF exposure
This device meets the official requirements for exposure to radio waves. This device is designed and
manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by
authorized agencies. The device must be used with a minimum separation of 20 cm from a person’s
body to ensure compliance with RF exposure guidelines. Failure to observe these instructions could
result in your RF exposure exceeding the applicable limits.
External antennas used with RUT200 must be installed to provide a distance of at least 20 cm from
any people and must not be co-located or operated in conjunction with any other antenna or
transmitter.
Any external antenna gain must meet RF exposure and maximum radiated output power limits of the
applicable rule section.
Maximum transmission power
GSM 33 dBm
WCDMA 24 dBm

LTE 23 dBm
WiFi 20 dBm
Operating conditions
Operating temperature: -40° to +75° Celsius
Humidity should be in the range of 10% to 90% (non-condensing). Only use the device in dry
environments.
Out of direct sunlight
Away from heat source, corrosive substances, salts, and flammable gases
Attention: operation outside the permissible range can considerably shorten the service life of the
device.
Faulty and damaged products
Do not attempt to disassemble the device or its accessories.
Only qualified personnel must service or repair the device or its accessories.
If your device or its accessories have been submerged in water punctured or subjected to a
severe fall, do not use until they have been checked at an authorized service center.
Electrical safety
Only use approved accessories.
Do not connect with incompatible products or accessories.
It is recommended to ground devices with grounding terminals before connecting them to
power. Failure to ground appropriately might result in a shock hazard. The cross-sectional
area of the protective grounding conductor should be at least 1mm2.
Product handling
You alone are responsible for how you use your device and any consequences related to its
use.
Use of your device is subject to safety measures designed to protect users and their
environment.
Always treat your device and its accessories with care and keep it in a clean and dust-free
place.
Do not expose your device or its accessories to open flames, lit tobacco products, liquid,
moisture, or high humidity.
Do not drop, throw or try to bend your device or its accessories.
Do not use harsh chemicals, cleaning solvents, or aerosols to clean the device or its
accessories.
Do not paint your device or its accessories.
Do not attempt to disassemble your device (exemptions for devices that require disassembly

for SIM insertion) or its accessories: it does not contain any user-serviceable parts. For safety
reasons, the equipment should be opened only by qualified personnel.
Make sure to use ESD personal protective equipment while the equipment is serviced.
Do not use your device in an enclosed environment where heat dissipation is poor.
Prolonged use in such space may cause excessive heat and raise ambient temperature, which
will lead to the automatic shutdown of your device or the disconnection of the mobile network
connection for your safety. To use your device again after such a shutdown, cool it in a well-
ventilated place before turning it on.
Please check all national laws and local regulations for the disposal of electronic products.
Do not operate the device where ventilation is restricted.
Do not use or install this product near water to avoid fire or shock hazards.
Avoid exposing the equipment to rain or damp areas.
Arrange power and Ethernet cables so that they are not likely to be stepped on or have items
placed on them.
Ensure that the voltage and the rated current of the power source match the device’s
requirements. Do not connect the device to an inappropriate power source.
During a thunderstorm, no operations should be carried out on the device and cables.
The unit must be powered off where blasting is in progress and explosive atmospheres are
present or near medical life support equipment.
Do not leave your device and its accessories within reach of small children or allow them to
play with it. They could hurt themselves or others and could accidentally damage the device.
Your device contains small parts with sharp edges that may cause an injury choking hazard.
Like any wireless device, this device operates using radio signals, which cannot guarantee
connection in all conditions. Therefore, you must never rely solely on any wireless device for
emergency communications or otherwise use the device in situations where the interruption of
data connectivity could lead to death, personal injury, property damage, data, or other loss.
The device may become warm during regular use.
Front view
Back view
Connectors
POWER SOCKET PINOUT

Video Quick Start Guide
Need some help setting up your new Teltonika Networks RUT200 Industrial Cellular Router? Watch
our quick start guide video and follow the step by step instructions to easily set up your new router
for operation.
Hardware installation
Configure your computer (Windows)
1. Ensure the
Wireless
network
connection is
Enabled. Go to
Start — Control
Panel —
Network and
Internet —
Network and
Sharing
Center. Click
on the Change
adapter
settings in the
left panel, then
right-click on
Wireless
Network
Adapter, and
select Enable.

2. Check if IP
and DNS are
obtained
automatically.
Right-click on
Wireless
Network
Adapter and
select
Properties.
Then select
Internet
Protocol
Version 4 and
click
Properties.
3. If not
selected, check
to obtain an
IP address
and obtain
DNS server
address
automatically.
Click OK.
4. Connect to a
wireless
network by
right-clicking
on Wireless
Network
Adapter and
selecting
Connect.
5. Choose the
wireless
network
RUT200 ****
from the list
and click
Connect. Enter
the WiFi
password
located on the
device's label.
Login to device

1. To enter the
router's Web
interface
(WebUI), type
http://192.168.1.1
into the URL field
of your Internet
browser.
2. When
prompted for
authentication
enter the
username admin
and enter the
password located
on the device
information
label/engraving.

3. After logging
in, you must set a
new password for
security reasons.
You will not be
able to interact
with the router’s
WebUI until the
default password
is changed. The
new password
must consist of a
minimum of 8
characters.
Requirements:
one uppercase
letter, one
lowercase letter,
and one digit.
4. Next, the
Configuration
Wizard will start
to help you set up
some of the
router's main
operational
parameters.
5. Finally, let's
verify the Mobile
signal strength.
Go to the Status
— Network page
and pay attention
to the Signal
Strength
indication.
To achieve the
best signal
conditions and
maximize cellular
performance, try
adjusting the
antennas or
changing the
location of your
device. You can
find information
on signal
strength
recommendations
here.
SIM card recommendations
Before installing the SIM cards, please apply a thin layer of dielectric grease to the SIM card
contacts for devices used in environments with high-vibration levels. This will help avoid
SIM cards losing touch with the SIM slot and prevent unexpected failures.
Industrial Grade SIM cards are recommended for devices requiring a long lifespan used in
environments with extreme temperatures, corrosive or extra humid climates, or hard-to-

reach locations.