Teltonika RUT240 User manual

Saltoniškių g. 9B-1,
LT-08105 Vilnius
Tel. [phone]
Faks. [phone]
www.teltonika-iot-group.com
[email protected]
RUT240 First Start
From Wiki Knowledge Base | Teltonika
This is the approved revision of this page, as well as being the most recent.
Main Page > Network products > RUT240 > RUT240 First Start
This Wiki page contains the online version of the Quick Start Guide (QSG) for the RUT240 LTE Router. Here you will nd an overview of the
various components found on the front and back sides of a RUT240 device, basic hardware installation, rst login information, device
specications and general safety information. It is highly recommended that you acquaint yourself with with the Quick Start Guide before using
the device. If you own a RUT240 device, you can also nd a printed version of the Quick Start Guide in the device's package.
Contents
1 Front view
2 Back view
3 Connectors
4 Hardware installation
5 Congure your computer (Windows)
6 Login to device
7 Safety information
Front view
No. Description
1 Power LED

Saltoniškių g. 9B-1,
LT-08105 Vilnius
Tel. [phone]
Faks. [phone]
www.teltonika-iot-group.com
[email protected]
2 Power socket
3 Network type LED
4 SIM holder
5 Mobile signal strength indication LEDs
6 Ethernet ports
7 LAN LED
8 WAN LED
Back view
No. Description
1 WiFi antenna connectors
2 Reset button
3 LTE antenna connectors
Connectors
Power socket pinout
No. Description Wire color
1 Power Red
2 Ground Black

Saltoniškių g. 9B-1,
LT-08105 Vilnius
Tel. [phone]
Faks. [phone]
www.teltonika-iot-group.com
[email protected]
3 Input Green
4 Output White
.
Hardware installation
1. Remove the SIM card slot tray with the pin needle. Insert your SIM card and push the tray back into the router. Correct SIM card
orientation can be seen in the gure below:
2. Attach LTE and WiFi antennas
3. Connect the power adapter to the power socket located on the front panel of the device. Then plug the other end of the power adapter
into a power outlet.

Saltoniškių g. 9B-1,
LT-08105 Vilnius
Tel. [phone]
Faks. [phone]
www.teltonika-iot-group.com
[email protected]
4. Connect to the device wirelessly (SSID: RUT240_****) or use an Ethernet cable.
Congure your computer (Windows)
1. Enable the wireless network connection (go to Start  Control Panel  Network and Internet  Network and Sharing Center. In the left
panel click the Change adapter settings link. Right click on Wireless Network Connection and select Enable).
2. Setup wireless network adapter on your computer (right click on Wireless Network Connection and select Properties. After that select
Internet Protocol Version 4 (TCP/IP) and click Properties).
3. Select Obtain IP address and Obtain DNS server address automatically if they are not selected. Click OK.

Saltoniškių g. 9B-1,
LT-08105 Vilnius
Tel. [phone]
Faks. [phone]
www.teltonika-iot-group.com
[email protected]
4. Right click on Wireless Network Connection and select Connect to see available wireless networks.

Saltoniškių g. 9B-1,
LT-08105 Vilnius
Tel. [phone]
Faks. [phone]
www.teltonika-iot-group.com
[email protected]
5. Choose the wireless network RUT240_**** from the list and click Connect. Enter the WiFi password located on the device's label.
Login to device
1. To enter the router's Web interface (WebUI), type http://192.168.1.1 into the URL eld of your Internet browser.
2. Use the following login information when prompted for authentication:

Saltoniškių g. 9B-1,
LT-08105 Vilnius
Tel. [phone]
Faks. [phone]
www.teltonika-iot-group.com
[email protected]
3. After you login, you will be prompted to change your password for security reasons. The new password must contain at least 8 characters,
including at least one uppercase letter, one lowercase letter and one digit. This step is mandatory and you will not be able to interact with
the router's WebUI before you change the password.
4. When you change the router's password, the Conguration Wizard will start. The Conguration Wizard is a tool used to setup some of the
router's main operating parameters.
5. Go to the Status  Network page and pay attention to the Signal Strength indication. To maximize cellular performance try adjusting the
antennas or changing the location of your device to achieve the best signal conditions (you can nd information on signal strength
recommendations here).

Saltoniškių g. 9B-1,
LT-08105 Vilnius
Tel. [phone]
Faks. [phone]
www.teltonika-iot-group.com
[email protected]
Safety information
The RUT240 router must be used in compliance with any and all applicable national and international laws and with any special restrictions
regulating the utilization of the communication module in prescribed applications and environments.
Radio specications
RF technologies GSM, GPRS, EDGE, UMTS/HSPA+, LTE, WiFi
Max RF power 33 dBm@GSM, 24 dBm@WCDMA, 23 dBm@LTE, 20 dBm@WiFi
Bundled accessories specications*
Power AC/DC power adapter 9 V 1 A, 4 pin plug
GSM/WCDMA/LTE antenna 698~960/1710~260 MHz, 50 Ω, VSWR < 3, gain** 3 dBi, omnidirectional, SMA male connector
WiFi antenna 2400~2483.5 MHz, 50 Ω, VSWR < 2, gain** 5dBi, omnidirectional, RP-SMA male connector

Saltoniškių g. 9B-1,
LT-08105 Vilnius
Tel. [phone]
Faks. [phone]
www.teltonika-iot-group.com
[email protected]
* Order code dependent.
** Higher gain antenna can be connected to compensate for cable attenuation when a cable is used. The user is responsible for the compliance
with the legal regulations.
This sign on the package means that is necessary to read the User's Manual before you start using the device
This sign on the package means that all used electronic and electric equipment should not be mixed with general household waste
Hereby, Teltonika declares that the radio equipment type RUT240 is in compliance with Directives: 2014/53/EU, 2014/35/EU, 2014/30/EU.
The full text of the EU declaration of conformity is available at the following internet address: http://teltonika.lt/product/rut240/
Retrieved from "https://wiki.teltonika.lt/wikibase/index.php?title=RUT240_First_Start&oldid=48174"